Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Mechanical Properties and Chemical Reactivity of Li x SiO y Thin Films

Silicon (Si) is a commonly studied candidate material for next-generation anodes in Li-ion batteries. A native oxide SiO 2 on Si is often inevitable. However, it is not clear if this layer has a positive or negative effect on the battery performance. This understanding is complicated by the lack of knowledge about the physical properties of the SiO 2 lithiation products and by the convolution of chemical and electrochemical effects during the anode lithiation process. In this study, Li x SiO y thin films as model materials for lithiated SiO 2 were deposited by magnetron sputtering at ambient temperature, with the goal of (1) decoupling chemical reactivity from electrochemical reactivity and (2) evaluating the physical and electrochemical properties of Li x SiO y . X-ray photoemission spectroscopy analysis of the deposited thin films demonstrate that a composition close to previous experimental reports of lithiated native SiO 2 can be achieved through sputtering. Our density functional theory calculations also confirm that the possible phases formed by lithiating SiO 2 are very close to the measured film compositions. Scanning probe microscopy measurements show that the mechanical properties of the film are strongly dependent on lithium concentration, with a ductile behavior at a higher Li content and a brittle behavior at a lower Li content. The chemical reactivity of the thin films was investigated by measuring the AC impedance evolution, suggesting that Li x SiO y continuously reacts with the electrolyte, in part because of the high electronic conductivity of the film determined from solid-state impedance measurements. The electrochemical cycling data of the sputter-deposited Li x SiO y /Si films also suggest that Li x SiO y is not beneficial in stabilizing the Si anode surface during battery operation, despite its favorable mechanical properties.

14 SOLAR ENERGY↗

Intrinsic Properties of Individual Inorganic Silicon–Electrolyte Interphase Constituents

Because of the complexity, high reactivity, and continuous evolution of the silicon-electrolyte interphase (SiEI), 'individual' constituents of the SiEI were investigated to understand their physical, electrochemical, and mechanical properties. For the analysis of these intrinsic properties, known SiEI components (i.e., SiO 2 , Li 2 Si 2 O 5 , Li 2 SiO 3 , Li 3 SiO x , Li 2 O, and LiF) were selected and prepared as amorphous thin films. The chemical composition, purity, morphology, roughness, and thickness of prepared samples were characterized using a variety of analytical techniques. On the basis of subsequent analysis we found, LiF shows the lowest ionic conductivity and relatively weak, brittle mechanical properties, while lithium silicates demonstrate higher ionic conductivities and greater mechanical hardness. This research establishes a framework for identifying components critical for stabilization of the SiEI, thus enabling rational design of new electrolyte additives and functional binders for the development of next-generation advanced Li-ion batteries utilizing Si anodes.

14 SOLAR ENERGY↗

Controlling Nanoscale Pore Size and Wall Composition in Polycarbonate Membranes via Atomic Layer Deposition and Sequential Infiltration Synthesis: Implications for High Water Permeance

Polymer membranes have a wide variety of applications, ranging from water treatment to energy storage. Many of these applications require precise control over the membrane porosity and surface chemistry. In this study, we explore the modification of isoporous polycarbonate (PC) track-etched membranes (PCTEs) by atomic layer deposition (ALD) and sequential infiltration synthesis (SIS) to tune the pore size and the pore wall surface chemistry. We first performed a detailed study of Al 2 O 3 ALD and SIS in PCTE using a variety of in situ and ex situ measurements. We discovered that short precursor exposure times are critical to achieve conformal Al 2 O 3 ALD in the PCTE nanopores, while longer precursor exposure times resulted in Al 2 O 3 SIS within the bulk of the PC leaving the membranes brittle. Next, we tuned the PCTE pore size via Al 2 O 3 ALD and studied its effect on the water contact angle and the water permeance. Here, we found that the membranes became more hydrophilic, and the permeance decreased with increasing ALD Al 2 O 3 cycles. Finally, we studied the effect of hydrophilic (SnO 2 )/hydrophobic (In 2 O 3 ) ALD metal oxide coatings on membrane properties. We found that the most hydrophilic SnO 2 showed the highest water flux and the least hydrophilic In 2 O 3 showed the lowest water flux through the PCTE membranes. Our results demonstrate that ALD is an effective method to tune the surface and transport properties of PCTE membranes, but care must be exercised to avoid SIS and bulk modification of the polymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Dual Approach in Direct Ink Writing of Thermally Cured Shape Memory Rubber Toughened Epoxy

Bisphenol A-based epoxies are much used in a wide range of composite and coating applications due to their excellent thermomechanical properties. However, their 3D printability remains a challenge with most reported materials suffering from high brittleness and low toughness. In this work, we have described especially modified epoxy resins that enable 3D printing with both fast and slow curing rates. These materials exhibit greatly enhanced toughness, tunable thermomechanical properties, and excellent shape memory behavior. Two different printing systems, including a two-part static mixing printhead and a single extrusion printhead, were developed for fast- and slow-curing epoxies, respectively. The rheology of inks in both systems has been modified into printable thixotropic fluids with the aid of silica nanoparticles and other additives. Epoxide-functionalized telechelic polybutadiene was added into the resins, which are then introduced inside the epoxy network after cross-linking. The addition of polybutadiene rubber significantly improves the toughness (over 135%), fracture strain (over 200%), and shape memory behavior. By adding different amounts of the rubber telechelic, thermomechanical properties, including modulus, elongation, and Tg of epoxy, can be well controlled in a wide range to satisfy different applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

3D Printable All-Polymer Epoxy Composites

Herein, 3D printable polymer-toughened epoxy resin composites are reported. Epoxy resins are widely used due to their excellent properties, such as thermal and chemical stability. However, their applications are limited by traditional mold-based manufacturing and their high brittleness. Mixtures of homopolymers, diblock copolymers, and triblock copolymers composed of poly(phenylene ether), poly(styrene), poly(methyl methacrylate), and poly(ethylene oxide) that self-assemble into micelles in the uncured resin are employed, providing a balance of structure, creep resistance, and flowability that enables 3D printing processing techniques and a retention of dimensional fidelity from the time of printing throughout the cured state. The precured ink is solid at room temperature and has strong shear-thinning behavior at elevated temperature for printing. As the printed parts cure, the polymer morphology evolves via reaction induced phase separation to yield finished composites with enhanced mechanical properties, including a 40% increase in the impact strength compared to the neat epoxy, without compromising thermal properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Upcycling of Polystyrene Waste to Poly(ionic liquid) Materials

The C–H functionalization of commodity polymers could be a promising approach for upcycling plastic waste into advanced materials, which can alter the properties of the original materials through the introduction of different functionalities onto the existing backbone structures. In this study, waste polystyrene (PS) was modified by Friedel–Crafts acylation using 4-chlorobutyryl chloride (4-CBC) followed by reaction with N-alkylimidazoles to form cationic polyelectrolytes. These methods provide access to what are essentially poly(ionic liquid) (poly(IL)) materials with properties that are distinctly different from those of the PS from which they were formed. In one notable example, the glass transition temperature (T g ) of imidazolium-functionalized PS was ∼16 °C, which is a nearly 90 °C reduction from PS. This is also evidenced by macroscopic mechanical properties where the poly(IL) product is highly elastic in stark contrast to brittle PS. Moreover, the resulting ionomers showed self-healing behaviors in the presence of a “free” IL further contributing to the utility of the materials. Here, the methods in this work can open opportunities to utilize waste PS to obtain a vast array of poly(IL) materials with highly tailored structures and properties.

36 MATERIALS SCIENCE↗

Comparing the Effects of Side Chain Dipole–Dipole Interactions and Hydrogen Bonding on the Mechanical and Electrical Properties of Poly(3-hexylthiophene)

Poly(3-alkylthiophenes) are simple conjugated polymers with good electrical properties, but tend to be brittle, limiting their application. Here, we investigate how side chain modifications can improve their toughness without compromising their charge transport. Specifically, we compare a weak dipole–dipole interaction of ester groups with a stronger hydrogen-bonding interaction of the hydroxyl groups. Two copolymers with targeted 5 and 10 mol % ester-functionalized side chains were synthesized and hydrolyzed in the solid state to introduce hydroxyl groups. Both hydrolyzed polymers became insoluble in most organic solvents, providing a path to layer-by-layer solution processing. All polymers’ optical, thermal, structural, electrical, and mechanical properties were investigated. Optical spectroscopy revealed that functionalization at these low levels did not significantly affect aggregation or π–π stacking. Differential scanning calorimetry indicated reduced crystallinity in the functionalized copolymers compared to that of P3HT. Grazing-incidence wide-angle X-ray diffraction data showed that functionalization led to an increase in lamellar spacing without altering molecular orientation or π–π stacking. Mechanical testing highlighted that at the lower functionalization level, both ester and hydroxyl groups similarly enhanced toughness, suggesting that disorder, rather than the specific nature of the functional group, was responsible for these improvements. At the higher functionalization level, hydroxyl groups significantly increased the elastic modulus while also negatively impacting charge carrier mobility. This study suggests that with stronger hydrogen-bonding groups, only very small amounts can improve P3HT’s toughness. For a wider tunable range, it may be a better strategy to use weak interactions such as dipole–dipole interactions of ester groups.

36 MATERIALS SCIENCE↗

Simultaneous in Situ X-ray Scattering and Infrared Imaging of Polymer Extrusion in Additive Manufacturing

In situ wide-angle X-ray scattering together with infrared imaging was performed during three-dimensional material extrusion printing and correlated with the development of the crystalline structure and subsequent thermomechanical properties. Identical samples were printed with nozzle motion either along the short axis or the long axis. The short axis mode had higher thermal retention, which resulted in later onset of crystal structure. The longer time spent at temperatures between the glass transition and the melting point produced samples with higher degree of crystallinity but also significantly increased brittleness. The tracer diffusion coefficient D ( T ), together with its temperature dependence, was measured using neutron reflectivity, and the total interdiffusion length between filaments was then calculated using D ( T ) for each temperature point, as determined by the measured thermal profiles. This allowed us to define the time/temperature plane that yielded the minimum diffusion length ΔL that provides mechanical integrity of the printed features ( ΔL less than the radius of gyration of the poly(l-lactide)). The model was probed by printing structures at four nozzle temperatures and measuring the time dependence of the thermal profiles at filaments in the horizontal and vertical positions. In conclusion, the data indicated that the thermal retention was anisotropic, where higher values were obtained in the horizontal plane. Mechanical measurements indicated large differential increases in the torsional strength, corresponding to the direction with increased thermal retention.

36 MATERIALS SCIENCE↗

Poly(lactic acid) Toughening through Chain End Engineering

The intrinsic brittleness of poly(lactic acid) (PLA) has hindered its widespread use in many structural applications. Various strategies have been developed to toughen PLA; however, most of the methods lead to a trade-off in strength or modulus. In this study, a chain end engineering strategy was developed to toughen PLA via an industry-friendly melt processing method. Green acids with multifunctional groups, such as 1,2,3,4-butanetetracarboxylic acid (BTCA), were used to modify PLA chain ends/tails via a melt reaction. We report a remarkable improvement in toughness (16×) was achieved by the addition of a minimal amount of BTCA (0.5%). At the same time, the toughened PLA samples maintained the tensile strength and Young’s modulus of neat PLA, suggesting a unique toughening mechanism that is different from the plasticizing effect. Other acid–based modifiers with different numbers of functional groups were also studied in this work. To understand the toughening, we propose a chain end engineering picture that can improve the toughness via a reduction in the number density of chain ends or defects of entanglement and the formation of long-branch topological structures. This study demonstrates a unique and cost-effective strategy for toughening PLA via scalable melt reaction without sacrificing other mechanical properties of PLA, potentially broadening the applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a Process for the Spinning of Synthetic Spider Silk

Spider silks have unique mechanical properties but current efforts to duplicate those properties with recombinant proteins have been unsuccessful. Here, this study was designed to develop a single process to spin fibers with excellent and consistent mechanical properties. As-spun fibers produced were brittle, but by stretching the fibers the mechanical properties were greatly improved. A water-dip or water-stretch further increased the strength and elongation of the synthetic spider silk fibers. Given the promising results of the water stretch, a mechanical double-stretch system was developed. Both a methanol/water mixture and an isopropanol/water mixture were independently used to stretch the fibers with this system. We found that the methanol mixture produced fibers with high tensile strength while the isopropanol mixture produced fibers with high elongation.

36 MATERIALS SCIENCE↗

Dual Alloying Strategy to Achieve a High Thermoelectric Figure of Merit and Lattice Hardening in p-Type Nanostructured PbTe

The introduction of an alkaline earth metal telluride as a second phase in PbTe can lead to very high thermoelectric figure of merit, ZT, as a result of hierarchical structuring, e.g., in the PbTe-SrTe system. However, there are two roadblocks to this strategy: poor solubility and occurrence of incoherent nanoprecipitates in the PbTe matrix, e.g., the PbTe-BaTe system. Here we demonstrate a dual alloying approach by simultaneously alloying CaTe and BaTe in the p-type PbTe matrix to achieve ZT max ranging up to ~2.2 at high temperatures. Synergistic enhancement of the Seebeck coefficient via favorable band convergence gives rise to higher power factors up to 34 μW cm -1 K -2 and significant suppression of lattice thermal conductivity, κ L , down to ~0.6 W m -1 K -1 results from large multicenter phonon scattering. In addition, co-inclusion of Ca and Ba causes unanticipated lattice hardening in otherwise brittle PbTe, essential for practical device applications.

36 MATERIALS SCIENCE↗

Hybrid Nanocrystals of Small Molecules and Chemically Disordered Polymers

Organic crystals formed by small molecules can be highly functional but are often brittle or insoluble structures with limited possibilities for use or processing from a liquid phase. A possible solution is the nanoscale integration of polymers into organic crystals without sacrificing long-range order and therefore function. This enables the organic crystals to benefit from the advantageous mechanical and chemical properties of the polymeric component. We report here on a strategy in which small molecules co-crystallize with side chains of chemically disordered polymers to create hybrid nanostructures containing a highly ordered lattice. Synchrotron X-ray scattering, absorption spectroscopy, and coarse-grained molecular dynamics simulations reveal that the polymer backbones form an “exo-crystalline” layer of disordered chains that wrap around the nanostructures becoming a handle for interesting properties. The morphology of this “hybrid bonding polymer” nanostructure is dictated by the competition between the polymers’ entropy and the enthalpy of the lattice allowing for control over the aspect ratio of the nanocrystal by changing the degree of polymer integration. Further, we observed that nanostructures with an exo-crystalline layer of polymer exhibit enhanced fracture strength, self-healing capacity, and dispersion in water, which benefits their use as light-harvesting assemblies in photocatalysis. Guided by computation, future work could also explore these hybrid nanostructures as building blocks for functional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Validated Reactive Force Field Quantifies MXene Interfacial Properties, Mechanics, and Thermal Transport

MXenes combine rich surface chemistry, mechanical strength, and high conductivity for a multitude of emerging applications. Predictive modeling supports accelerated materials designs and has been limited by the absence of validated and transferable force fields. Here, we introduce an interpretable, reactive INTERFACE force field (IFF and IFF-R) for Ti 3 C 2 T x MXenes that is trained based on chemical knowledge and achieves quantitative agreement with experiments across lattice parameters (<0.5%), density (<0.2%), liquid contact angles, Raman spectra, and the in-plane elastic modulus (∼320 GPa). The models cover surface terminations from hydroxyl (−OH) to fluorine (−F) groups and are extensible to other chemistries. We introduce pH-resolved surface chemistry and identify dopamine adsorption mechanisms at MXene–aqueous interfaces supported by QCM-D and UV–Vis experiments. The data reveal coplanar and perpendicular binding modes and concentration-dependent multilayer assembly. We predict previously inaccessible properties, including termination-dependent cleavage energies, interlayer shear moduli and dynamic shear failure, nanoindentation and brittle fracture, anisotropic in-plane and out-of-plane thermal conductivities, including the role of defects. Agreement with available experimental data is consistently close and exceeds DFT accuracy across the benchmark properties examined. The IFF/IFF-R model is compatible with CHARMM, AMBER, OPLS, and CVFF force fields for simulations of MXenes with diverse surface terminations, electrolyte interfaces, biointerfaces, and polymer composites without additional parameters. Parameter sets, 3D models, and analysis scripts are provided for community use. The validated, reactive, and transferable IFF framework facilitates predictive design of MXene-based films, membranes, sensing interfaces, and composites.

MXene↗

Quantifying Polymer Chain Orientation in Strong and Tough Nanofibers with Low Crystallinity: Toward Next Generation Nanostructured Superfibers

Advanced fibers revolutionized structural materials in the second half of the 20th century. However, all high-strength fibers developed to date are brittle. Recently, pioneering simultaneous ultrahigh strength and toughness were discovered in fine (<250 nm) individual electrospun polymer nanofibers (NFs). This highly desirable combination of properties was attributed to high macromolecular chain alignment coupled with low crystallinity. Quantitative analysis of the degree of preferred chain orientation will be crucial for control of NF mechanical properties. However, quantification of supramolecular nanoarchitecture in NFs with low crystallinity in the ultrafine diameter range is highly challenging. Here, we discuss the applicability of traditional as well as emerging methods for quantification of polymer chain orientation in nanoscale one-dimensional samples. Advantages and limitations of different techniques are critically evaluated on experimental examples. It is shown that straightforward application of some of the techniques to sub wavelength-diameter NFs can lead to severe quantitative and even qualitative artifacts. Sources of such size-related artifacts, stemming from instrumental, materials, and geometric phenomena at the nanoscale, are analyzed on the example of polarized Raman method but are relevant to other spectroscopic techniques. A proposed modified, artifact-free method is demonstrated. Outstanding issues and their proposed solutions are discussed. The results provide guidance for accurate nanofiber characterization to improve fundamental understanding and accelerate development of nanofibers and related nanostructured materials produced by electrospinning or other methods. Overall, we expect that the discussion in this review will also be useful to studies of many biological systems that exhibit nanofilamentary architectures and combinations of high strength and toughness.

36 MATERIALS SCIENCE↗

Effects of Recovery Conditions and Aggregation Mechanisms on the Chemical and Physical Properties of Hybrid Poplar and Corn Stover Lignins

Heterogeneity in the physical properties and processing behavior of lignins recovered from biorefining process streams can hinder their effective utilization and industrial valorization. This work investigates lignin recovery by acidification from alkaline pretreatment liquors of varying sources (corn stover and hybrid poplar), compositions, solid contents, and incubation temperatures prior to filtration. Recovered lignins were characterized for filtration performance, mass yield, chemical composition, particle size and morphology, and color. A transition temperature was identified corresponding to marked shifts in lignin physical properties and was a function of the solid content and liquor source. Filtration below this temperature yielded slow-filtering, dark, brittle lignins with smoother particle surfaces, whereas precipitation above this threshold yielded fast-filtering, lighter, powdery lignins with rougher particle surfaces. The impact of temperature and concentration on universal cluster aggregation mechanisms was proposed to explain the differences between lignin particle properties and filtration behavior.

Aggregation↗

Directly Probing the Fracture Behavior of Ultrathin Polymeric Films

Understanding fracture mechanics of ultrathin polymeric films is crucial for modern technologies, including semiconductor and coating industries. However, up to now, the fracture behavior of sub-100 nm polymeric thin films is rarely explored due to challenges in handling samples and limited testing methods available. In this work, we report a new testing methodology that can not only visualize the evolution of the local stress distribution through wrinkling patterns and crack propagation during the deformation of ultrathin films but also directly measure their fracture energies. Using ultrathin polystyrene films as a model system, we both experimentally and computationally investigate the effect of the film thickness and molecular weight on their fracture behavior, both of which show a ductile-to-brittle transition. Furthermore, we demonstrate the broad applicability of this testing method in semicrystalline semiconducting polymers. We anticipate our methodology described here could provide new ways of studying the fracture behavior of ultrathin films under confinement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tunable and Degradable Dynamic Thermosets from Compatibilized Polyhydroxyalkanoate Blends

Polyhydroxyalkanoates (PHAs) are versatile, biobased polyesters that are often targeted for use as degradable thermoplastic replacements for polyolefins. Given the substantial chemical diversity of PHA, their potential as cross-linked polymers could also enable similar platforms for reversible, degradable thermosets. In this work, we genetically engineered Pseudomonas putida KT2440 to synthesize poly(3-hydroxybutyrate-co-3-hydroxyundecenoate) (PHBU), which contains both 3-hydroxybutyrate and unsaturated 3-hydroxyundecenoate components. To reduce the brittleness of this polymer, we physically blended PHBU with the soft copolymer poly(3-hydroxydecanonate-co-3-hydroxyundecenoate) in mass ratios of 1:3, 1:1, and 3:1. Upon observing varying degrees of immiscibility by scanning electron microscopy, we installed dynamic boronic ester cross-links via thiol–ene click chemistry, which resulted in compatibilized dynamic thermoset blends ranging in hard, medium, and soft rubber or elastomer thermomechanical profiles. These dynamic thermoset blends were subjected to controlled biological degradation experiments in freshwater conditions, achieving timely mass loss despite the cross-linked architectures. Overall, this work highlights a two-component platform for the production of degradable and reprocessable dynamic thermoset blends suitable for several classes of cross-linked polymer technologies from tailored, biological PHA copolymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Supertough PLA-Silane Nanohybrids by in Situ Condensation and Grafting

Brittleness is a key barrier for poly(lactic acid) (PLA) toward broader applications. Supertough PLA was achieved by simply mixing a low amount (0.5–1 wt %) of organoalkoxysilane with PLA. Three organosilanes, (3-aminopropyl)triethoxysilane (APTES), 3-(triethoxysilyl)propyl isocyanate (ICPTES), and trimethoxymethylsilane (MTMS), were selected for this study to understand how the functional group on a silane affects the behavior of the PLA-silane hybrids. Remarkable improvements in ultimate tensile strain (up to 12 folds) and tensile toughness (up to 10 folds) were observed in APTES- and ICPTES-modified PLA without any loss in tensile strength and modulus. Glass transition temperatures measured by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) did not show any obvious decrease. We propose that in situ condensation of organosilane and grafting of PLA to form a silica-PLA core–shell nanocomplex may be the reason for the improved mechanical properties. Scanning electron microscopy (SEM) showed evidence of nanofibrils at fractured surfaces. Dynamic light scattering (DLS) indicated nanoparticle formation (bimodal, 50–200 nm and <10 nm) in dilute solution, while transmission electron microscopy (TEM) provided clearer evidence of the nanosized silica formed in situ. Rheological studies also showed increased chain entanglement in the polymer melts, which contributed to 1 order of magnitude higher complex viscosity and storage modulus. The simple PLA toughening strategy and the new mechanism revealed in this study will open a door to novel performance polymer materials and broader use of PLAs.

36 MATERIALS SCIENCE↗