SEARCH · Engineering Papers

Results for “Accelerator design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

All sources NASA NTRS DOE OSTI

NASA NTRS1988

The radial velocity search for extrasolar planets

Researchers are measuring small changes in the line-of-sight velocities of stars to detect the oscillating reflex acceleration induced by large planets. The intention is to observe enough stars for a long enough time to be able to make a statement of the probability of planets in a certain range of masses even if no planetary perturbations are detected. To make these measurements of Doppler shift with the required sensitivity, a new instrument was specifically designed, built and tested for this campaign of ground-based planet detection. The instrument is an optical spectrometer for which wavelengths are first calibrated by transmission through a tunable Fabry-Perot etalon interferometer. The intrinsic stability of the etalon and an image-scrambling fiber optic light feed provide great sensitivity to line-of-sight accelerations and immunity to systematic errors.

Mcmillen, Robert S.↗

NASA NTRS1992

Future radiation measurements in low Earth orbit

The first Long Duration Exposure Facility (LDEF) mission has demonstrated the value of the LDEF concept for deep surveys of the space radiation environment. This paper will survey the types of measurements that could be done on a second LDEF mission. One of the most surprising discoveries on LDEF1 was the Be-7 that was found imbedded on the windward surface. LDEF2 could follow up on this discovery and search for evidence of other cosmogenic nuclei. Another experiment could be designed to investigate the presence of energetic heavy ions observed on LDEF1. The relative abundance of rare earths can also be used to search for evidence that cosmic rays accelerate in episodes which occur throughout their propagation in the stellar medium. Further investigations of radiation effects could also be undertaken. A second LDEF mission also offers the opportunity for new investigations such as measurements of cosmic ray differential energy spectrum to ultrahigh energies. These and other ideas will be discussed.

Adams, James H., Jr.↗

NASA NTRS1990

COLD-SAT orbital experiment configured for Altas launch

A study was done of the feasibility of conducting liquid hydrogen orbital storage, acquisition, and transfer experiments aboard a spacecraft launched by a commercial Atlas launch vehicle. Three hydrogen tanks are mated to a spacecraft bus that is similar to that used for three-axis-controlled satellites. The bus provides power, communications, and attitude control along with acceleration levels ranging from 10 exp -6 to 10 exp -4 g. At launch, all the liquid hydrogen is contained in the largest tank, which has an insulation system designed for both space operation and the short-term launch pad and ascent environment. This tank is much lighter and lower in cost than a vacuum-jacketed design, and is made possible by the experiment tanking options available due to the hydrogen-fueled Centaur upper stage of the Atlas I.

Schuster, J. R.↗

NASA NTRS1990

Installing scientific instruments into a cold LHe dewar - The Gravity Probe B approach

Gravity Probe B is an orbital test of Einstein's general theory of relativity using gyroscopes. The precession of the gyroscopes will measure both the geodetic effect (6.6 arcsec/yr) through the curved space-time surrounding the earth and the motional effect (0.042 arcsec/yr) due to the rotating earth dragging space-time around with it. To achieve the extraordinary accuracies needed to measure these small precessions, it is necessary to have the gyroscopes operating in the following environments: a vacuum of less than 10 exp -10 torr; an acceleration level of less than 10 exp -10 g's; a magnetic field of less than 10 exp -7 gauss; and a temperature near 2 K. This paper discusses designs that allow scientific instruments to be installed into a dewar at 4.2 K. Methods for structurally supporting the instruments, transferring heat across joints at low temperature in vacuum, and excluding air during the insertion process are discussed. The structural support method is designed for Shuttle launch loads.

Parmley, Richard T.↗

NASA NTRS2003

Momentum and Heat Flux Measurements in the Exhaust of VASIMR using Helium Propellant

Interplanetary travel requires propulsion systems that can provide high specific impulse (Isp), while also having sufficient thrust to rapidly accelerate large payloads. One such propulsion system is the Variable Specific Impulse Magneto-plasma Rocket (VASIMR), which creates, heats, and ejects plasma to provide variable thrust and Isp, designed to optimally meet the mission requirements. The fraction of the total energy invested in creating the plasma, as compared to the plasma's total kinetic energy, is an important factor in determining the overall system efficiency. In VASIMR, this 'frozen flow loss' is appreciable when at high thrust, but negligible at high Isp. The loss applies to other electric thrusters as well. If some of this energy could be recovered through recombination processes, and reinjected as neutral kinetic energy, the efficiency of VASIMR, in its low Isp/high thrust mode may be improved. An experiment is being conducted to investigate the possibility of recovering some of the energy used to create the plasma by studying the flow characteristics of the charged and neutral particles in the exhaust of the thruster. This paper will cover the measurements of momentum flux and heat flux in the exhaust of the VASIMR test facility using helium as the propellant where the heat flux is comprised of both kinetic and plasma recombination energy. The flux measurements also assist in diagnosing and verifying the plasma conditions in the existing experiment.

Chavers, D. Gregory↗

NASA NTRS2010

Rocket Cratering in Simulated Lunar and Martian Environments

With NASA's planned return to the moon and possibly with lunar outposts being formed, repeated landings at the same site will be necessary. Understanding rocket plume interaction with lunar and Martian surfaces is of paramount importance in order to safely land and protect hardware surrounding the landing site. This work will report on results of three small experiments intended to explore plume impingement onto lunar and Martian surfaces: Handheld Observation of Scour Holes (HOOSH), Handheld Angle of Repose Measurements of Lunar Simulants (HARMLuS), and Mars Architecture Team study (MATS). The first two experiments were performed during two sorties of reduced gravity flights. HOOSH was designed to investigate crater formation as a function of gravitational level (lunar and Martian gravity). HARMLuS was designed to measure the Angle of Failure (related to the angle of repose) at lunar and Martian gravity. Both experiments have complex findings indicative of the hysteretic behavior of granular materials, especially resulting from reduced gravity. The MATS experiment was designed to investigate the effects of regolith compaction on the granular mechanics of crater formation . In general, the granular mechanics is a much stronger function of compaction than gravitation acceleration. Crater formation is greatly enhanced at reduced gravity (resulting in much larger craters). The angle of failure of the lunar simulants increases with decreasing gravitational acceleration, and occasionally becomes infinite for some compactions at lunar gravity. The angle of failure also increases with increasing compaction. While compaction does play a role in the time development of crater formation, the asymptotic behavior is largely unaffected.

Immer, Christopher↗

NASA NTRS2011

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

A rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for a curved orthogrid panel typical of launch vehicle skin structures. Several test article configurations were produced by adding component equipment of differing weights to the flight-like vehicle panel. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was employed to describe the assumed correlation of phased input sound pressures across the energized panel. This application demonstrates the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software modules developed for the RPTF method can be easily adapted for quick replacement of the diffuse acoustic field with other pressure field models; for example a turbulent boundary layer (TBL) model suitable for vehicle ascent. Wind tunnel tests have been proposed to anchor the predictions and provide new insight into modeling approaches for this type of environment. Finally, component vibration environments for design were developed from the measured and predicted responses and compared with those derived from traditional techniques such as Barrett scaling methods for unloaded and component-loaded panels.

Frady, Gregory P.↗

NASA NTRS2014

Navigation Design and Analysis for the Orion Earth-Moon Mission

This paper details the design of the cislunar optical navigation system being proposed for the Orion Earth-Moon (EM) missions. In particular, it presents the mathematics of the navigation filter. The unmodeled accelerations and their characterization are detailed. It also presents the analysis that has been performed to understand the performance of the proposed system, with particular attention paid to entry flight path angle constraints and the delta-V performance.

DSouza, Christopher↗

NASA NTRS2015

High-Efficiency Hall Thruster Discharge Power Converter

Busek Company, Inc., is designing, building, and testing a new printed circuit board converter. The new converter consists of two series or parallel boards (slices) intended to power a high-voltage Hall accelerator (HiVHAC) thruster or other similarly sized electric propulsion devices. The converter accepts 80- to 160-V input and generates 200- to 700-V isolated output while delivering continually adjustable 300-W to 3.5-kW power. Busek built and demonstrated one board that achieved nearly 94 percent efficiency the first time it was turned on, with projected efficiency exceeding 97 percent following timing software optimization. The board has a projected specific mass of 1.2 kg/kW, achieved through high-frequency switching. In Phase II, Busek optimized to exceed 97 percent efficiency and built a second prototype in a form factor more appropriate for flight. This converter then was integrated with a set of upgraded existing boards for powering magnets and the cathode. The program culminated with integrating the entire power processing unit and testing it on a Busek thruster and on NASA's HiVHAC thruster.

Jaquish, Thomas↗

NASA NTRS2010

Orion Entry Performance-Based Center-of-Gravity Box

The Orion capsule has many performance requirements for its atmospheric entry trajectory. Requirements on landing accuracy, maximum heating rate, total heat load, propellant usage, and sensed acceleration must all be satised. It is desired to define a methodology to translate the many performance requirements for an atmospheric entry trajectory into language easily understood by vehicle designers in terms of an allowable center-of-gravity box. This is possible by noting that most entry performance parameters for a capsule vehicle are mainly determined by the lift-to-drag ratio of the vehicle. However, the lift-to- drag ratio should be considered a probabilistic quantity rather than deterministic, where variations in the lift-to-drag are caused by both aerodynamic and center-of-gravity un- certainties. This paper discusses the technique used by the Orion program to define the allowable dispersions in center-of-gravity to achieve the desired entry performance while accounting for aerodynamic uncertainty.

Rea, Jeremy R.↗

NASA NTRS2018

NASA's Centennial Challenge for 3D-Printed Habitat: Phase II Outcomes and Phase III Competition Overview

The 3D-Printed Habitat Challenge is part of NASA's Centennial Challenges Program. NASA's Centennial Challenges seek to accelerate innovation in aerospace technology development through public competitions. The 3D-Printed Habitat Challenge, launched in 2015, is part of the Centennial Challenges portfolio and focuses on habitat design and development of large-scale additive construction systems capable of fabricating structures from in situ materials and/or mission recyclables. The challenge is a partnership between NASA, Caterpillar (primary sponsor), Bechtel, Brick and Mortar Ventures, and Bradley University. Phase I of the challenge was an architectural concept competition in which participants generated conceptual renderings of habitats on Mars which could be constructed using locally available resources. Phase II asked teams to develop the printing systems and material formulations needed to translate these designs into reality. Work under the phase II competition, which concluded in August 2017 with a head to head competition at Caterpillar's Edward Demonstration Facility in Peoria, Illinois, is discussed, including the key technology development outcomes resulting from this portion of the competition. The phase III competition consists of both virtual and construction subcompetitions. Virtual construction asks teams to render high fidelity architectural models of a habitat and all the accompanying information required for construction of the pressure retaining and load bearing portions of the structure. In construction phase III, teams are asked to scale up their printing systems to produce a 1/3 scale habitat on-site at Caterpillar. The levels of the phase III construction competition (which include printing of a foundation and printing and hydrostatic testing of a habitat element) are discussed. Phase III construction also has an increased focus on autonomy, as these systems are envisioned for robotic precursor missions which would buildup infrastructure prior to the arrival of crew. Results of the phase III competition through July 2017 (which includes virtual construction level 1) are discussed. This Centennial Challenge enables an assessment of the scaleability and efficacy of various processes, material systems, and designs for planetary construction. There are also near-term terrestrial applications, from disaster response to affordable housing and infrastructure refurbishment, for these technologies.

Prater, T. J.↗

NASA NTRS2018

The Hayabusa2 Sample Return Mission and Its Small Carry-On Impactor Experiment

On December 3, 2014 the Hayabusa2 Spacecraft was launched by JAXA to investigate and return samples from carbonaceous Asteroid (162173) Ryugu. The spacecraft's payload contains several remote sensing instruments that are designed to characterize the asteroid's surface and to help identify scientifically interesting locations from which samples can be obtained safely. The data collected by these instruments will also help place any obtained samples in context with respect to the global characteristics of Ryugu. In addition to the suite of remote sensing instruments and the sampling device, Hayabusa2 also includes a small carry-on impactor (SCI) payload experiment, which is designed to impact the surface of the asteroid and excavate fresh material for subsequent collection. The SCI consists of a 30 cm diameter 2 kg copper disk that is accelerated by an explosive charge into the surface of Ryugu at approximately 2 km/s. The resultant crater formed during this experiment is estimated to be approximately between 2 - 10 meters in diameter with an ejecta blanket extending to 10 - 100 meters on the asteroid. Hayabusa2 will not be able to observe the impact experiment directly due to considerations of spacecraft safety since there is some risk of collisions with debris from the explosion and ejecta from the crater. However, prior to moving safely away, the spacecraft will deploy a small imaging system called Deployable Camera 3 (DCAM3). DCAM3 will detach from Hayabusa2 just before the detonation of the SCI and will image the moment of impact, crater formation, and ejecta propagation. These data will be transmitted to Hayabusa2 and will help constrain the near-surface properties of Ryugu and also impact scaling laws for small bodies in low gravity environments. These data could also be useful for gaining insights into determining asteroid physical properties from higher velocity impact events (e.g., DART and HERA data of Didymos).

Abell, Paul A.↗

NASA NTRSDate not supplied

Trajectory Simulation for Air Traffic Management Employing a Multirotor Urban Air Mobility Aircraft Model

This paper describes a point-mass model of a multirotor electric vertical takeoff and landing aircraft designed to carry up to five passengers and a pilot. The model employs thrust, thrust vector angle and bank angle as controls, which are computed in part using the acceleration, heading-angle rate, and flight-path-angle rate generated by control systems in response to speed, heading angle, and flight-path angle commands. The equations of motion are integrated forward in time using the controls needed for following the desired vertical climb/descent and speed profiles, and horizontal path and cruise speed in the presence of wind to generate the flight trajectory.

trajectory simulation, urban air mobility aircraft↗

NASA NTRS1989

Conceptual design of a moving belt radiator shuttle-attached experiments: Technical requirement Document

The technical requirements for a shuttle-attached Moving Belt Radiator (MBR) experiment are defined. The MBR is an advanced radiator concept in which a rotating belt radiates thermal energy to space. The requirements for integrating the MBR experiment in the shuttle bay are discussed. Requirements for the belt material and working fluid are outlined along with some possible options. The proposed size and relationship to a full scale Moving Belt Radiator are defined. The experiment is defined with the primary goal of dynamic testing and a secondary goal of demonstrating the sealing and heat transfer characteristics. A perturbation system which will simulate a docking maneuver or other type of short term acceleration is proposed for inclusion in the experimental apparatus. A deployment and retraction capability which will aid in evaluating the dynamics of a belt during such a maneuver is also described. The proposed test sequence for the experiment is presented. Details of the conceptual design are not presented herein, but rather in a separate Final Report.

Aguilar, Jerry L.↗

NASA NTRS1991

Reusable Reentry Satellite (RRS) system design study

The Reusable Reentry Satellite (RRS) is intended to provide investigators in several biological disciplines with a relatively inexpensive method to access space for up to 60 days with eventual recovery on Earth. The RRS will permit totally intact, relatively soft, recovery of the vehicle, system refurbishment, and reflight with new and varied payloads. The RRS is to be capable of three reflights per year over a 10-year program lifetime. The RRS vehicle will have a large and readily accessible volume near the vehicle center of gravity for the Payload Module (PM) containing the experiment hardware. The vehicle is configured to permit the experimenter late access to the PM prior to launch and rapid access following recovery. The RRS will operate in one of two modes: (1) as a free-flying spacecraft in orbit, and will be allowed to drift in attitude to provide an acceleration environment of less than 10(exp -5) g. the acceleration environment during orbital trim maneuvers will be less than 10(exp -3) g; and (2) as an artificial gravity system which spins at controlled rates to provide an artificial gravity of up to 1.5 Earth g. The RRS system will be designed to be rugged, easily maintained, and economically refurbishable for the next flight. Some systems may be designed to be replaced rather than refurbished, if cost effective and capable of meeting the specified turnaround time. The minimum time between recovery and reflight will be approximately 60 days. The PMs will be designed to be relatively autonomous, with experiments that require few commands and limited telemetry. Mass data storage will be accommodated in the PM. The hardware development and implementation phase is currently expected to start in 1991 with a first launch in late 1993.

Source record↗

NASA NTRS1974

Laboratory demonstration model: Active cleaning technique device

The technique which utilizes exposure to a plasma to remove contaminants from a surface was incorporated into a laboratory model which demonstrates active cleaning by both plasma cleaning and ion sputtering modes of operation. The development phase is reported and includes discussion of the plasma tube configuration, device design, and performance tests. A general description of the active cleaning device is provided which includes information on the main power/plasma discharge sensors, and the power, gas supply, and ion accelerator systems. Development of the active cleaning species at high vacuum conditions is described and results indicate that plasma cleaning occurs in the region of a visible plume which extends from the end of the plasma tube. Recommendations are made for research to determine the plasma cleaning mechanism and the plasma species responsible for the cleaning, as well limitations on the type of contaminants that can be removed.

Shannon, R. L.↗

NASA NTRS1976

Laser Doppler spectrometer method of particle sizing

A spectrometer for the detection of airborne particulate pollution in the submicron size range is described. In this device, airborne particles are accelerated through a supersonic nozzle, with different sizes achieving different velocities in the gas flow. Information about the velocities of the accelerated particles is obtained with a laser-heterodyne optical system through the Doppler shift of light scattered from the particles. Detection is accomplished by means of a photomultiplier. Nozzle design and signal processing techniques are also discussed.

Weber, F. N.↗

NASA NTRS1980

Reduction of unsteady wind torques on an open port airborne optical turret

Techniques for reducing the unsteady torques acting on the inner gimbal of a turret were developed. The reductions in the unsteady torques were obtained by using fixes that alter undesirable flow characteristics or change the acoustic properties of the turret cavity. These fixes were designed to be used in the subsonic and transonic flow regimes. The flow field about the turret generally three dimensional and turbulent, and shock waves formed because of the rapid acceleration of the compressible gas about the blunt turret. The situation was further complicated by the presence of the cavity flow, and the fact that the mouth of the cavity must sweep through a wide angular variation relative to the direction of the freestream. Results indicate that significant reductions of the unsteady pressures measured in the turret cavity could be obtained by the use of porous wind screens around the aperature of the cavity mouth.

Thomas, J. P., Jr.↗