Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zinc”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

CdTe‐Based Solar Cells with Variations in Mg Concentration in the MgZnO Emitter

The optimal fraction of Mg incorporation in sputter-deposited Mg X Zn 1−X O (MZO) emitters for thin-film CdTe-based solar cells is evaluated by varying it over a range of x from 0 to 0.35. This range allows a variation in the conduction band offset from −0.1 eV (cliff like) to +0.32 eV (spike like). Here, a maximum efficiency of 18.5% for cells with the bilayer CdSeTe/CdTe absorber occurs at x = 0.15, which corresponds to a spike-like band offset near 0.2 eV, as confirmed by X-ray photoelectron spectroscopy. In addition, good cell performance is seen over a fairly broad range of x extending from 0.1 to 0.25. The MZO optical bandgap increases with the Mg fraction, consistent with an increasing conduction band offset. Temperature-dependent current−voltage measurements and time-resolved photoluminescence show improvement in the emitter/absorber interface with the incorporation of Mg. Capacitance−voltage measurements show that the depletion region extends further into the absorber with more Mg, and X-ray diffraction confirms a change from a hexagonal-dominant crystal structure toward zinc blende at x = 0.35.

14 SOLAR ENERGY↗
DOE OSTI2025

Monocrystalline CdSeTe/MgCdTe Double‐Heterostructure Solar Cells

This article reports monocrystalline CdSeTe/MgCdTe double‐heterostructure (DH) solar cells with varying Se compositions in the absorber layers that are grown on InSb substrates by using molecular beam epitaxy. The Se composition in the samples studied is determined to be 4%–11% through high‐resolution X‐ray diffraction (XRD) and photoluminescence measurements. Increased Se incorporation induces higher defect density attributed to increased lattice mismatch, and mixed‐phase formation due to the small difference in formation energies between the wurtzite and zinc blende phases of CdSe, which causes stacking faults and grain boundaries. Devices are fabricated by directly depositing an n‐type indium tin oxide (ITO) layer on the CdSeTe/MgCdTe DHs followed by Ag metal contacts. Reduced bandgap is observed in solar cells with increased Se composition. The devices with an absorber containing 4% Se exhibit an average open‐circuit voltage ( V OC ) of 0.925 V, a short‐circuit current density ( J SC ) of 23.4 mA/cm 2 , a fill factor ( FF ) of 0.650 and an efficiency of 14.1% without anti‐reflection coating. Absorbers with higher Se compositions result in poor device performance, mainly attributed to high defect density in the materials.

Ju, Zheng [Center for Photonics Innovation Arizona↗
DOE OSTI2024

Role of Selenium in CdZnTeSe as a Defect Engineering Agent

Cadmium zinc telluride (CdZnTe) with 10 atomic % Zn has been the material of choice for room-temperature semiconductor compact X- and gamma-ray detector applications for over three decades. Despite its commercial success as the most desirable room-temperature semiconductor radiation detection material, CdZnTe (CZT) suffers from a lack of compositional homogeneity on both the micro- and macroscales and the presence of high concentrations of performance-limiting defects such as subgrain boundary networks (dislocation walls) and secondary phases (Te-rich inclusions). Random distributions of these defects in the CZT matrix result in the spatial inhomogeneity of the material’s charge-transport properties. The recently discovered quaternary Cd x Zn 1-x Te 1-y Se y (CZTS) has experienced remarkable advances in its material properties, with highly reduced defects and higher compositional homogeneity. This book chapter focuses on the presence of performance-limiting defects in CZT that have thus far hindered the yield and cost of high-quality detectors and restricted their widespread deployment for a variety of potential applications, particularly for their use as large-volume gamma detectors, where the demands on material perfection are significantly greater. This chapter also provides an overview of the recent developments in the quaternary material CZTS, particularly the effects of selenium (Se) in the CZTS matrix on the defect engineering of the quaternary alloy material and the advancement of CZTS as a potential next-generation detector operable at room temperature.

Roy, Utpal N.↗
DOE OSTI2021

Metal Removal by a Free Surface Constructed Wetland and Prediction of Metal Bioavailability and Toxicity with Diffusive Gradients in Thin Films (DGT) and Biotic Ligand Model (BLM)

The H-02 constructed wetland is a free water surface wetland to remove copper (Cu) and zinc (Zn) from the industrial wastewater. In this study, we evaluated the performance of the wetland from 2018 to 2019 and coupled the diffusive gradients in thin films (DGTs) and biotic ligand model (BLM) to explore metal speciation and bioavailability in wetland waters. Surface water samples were collected and piston DGTs were deployed in different sites of the wetland. The H-02 wetland functioned well during the sampling period with high removal efficiencies (Cu: 73.8 ± 1.2% and Zn: 75.2 ± 16.0%). In our study, with the assumption that the combination of BLM predicted inorganic metals species, BLM Cu(II) and BLM Zn(II), were the bioavailable and toxic species, DGT-Cu did not correlate to BLM Cu(II) (P = 0.47), but DGT-Zn positively correlated to BLM Zn(II) (R 2 = 0.35, P < 0.001). Compared to the modeling results of BLM, DGT-indicated labile and/or bioavailable Cu included not only free Cu ions and inorganic Cu complexes but also a high percentage of Cu-labile organic matter complexes. DGT-indicated Zn included free Zn ion, inorganic Zn, and only a low percentage of Zn-labile organic matter complexes. Our findings illustrated the appropriate use of passive sampling techniques and geological modeling when biomonitoring could be substituted. Furthermore, the close monitoring of metal concentrations, speciation, and bioavailability helps us understand metal biogeochemistry and metal removal processes and ensure the long-term sustainability of the constructed wetland.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Mycorrhizal status and host genotype interact to shape plant nutrition in field grown maize ( Zea mays ssp. mays )

Arbuscular mycorrhizal fungi (AMF) establish symbioses with the major cereal crops, providing plants with increased access to nutrients while enhancing their tolerance to toxic heavy metals. However, not all plant varieties benefit equally from this association. In this study, we used quantitative trait loci (QTL) mapping to evaluate the combined effect of host genotypic variation (G) and AMF across 141 genotypes on the concentration of 20 mineral elements in the leaves and grain of field grown maize (Zea mays spp. mays). Our mapping design included selective incorporation of a castor AMF-incompatibility mutation, allowing estimation of AMF, QTL and QTLxAMF effects by comparison of mycorrhizal and non-mycorrhizal plants. Overall, AMF compatibility was associated with higher concentrations of boron (B), copper (Cu), molybdenum (Mo), phosphorus (P), selenium (Se) and zinc (Zn) and lower concentrations of arsenic (As), iron (Fe), magnesium (Mg), manganese (Mn), potassium (K) and strontium (Sr). In addition to effects on individual elements, pairwise correlation matrices for element concentration differed between mycorrhizal and non-mycorrhizal plants. We mapped 22 element QTLs, including 18 associated with QTLxAMF effects that indicate plant genotype-specific differences in the impact of AMF on the host ionome. Although there is considerable interest in AMF as biofertilizers, it remains challenging to estimate the impact of AMF in the field. Our design illustrates an effective approach for field evaluation of AMF effects. Furthermore, we demonstrate the capacity of the ionome to reveal host genotype-specific variation in the impact of AMF on plant nutrition.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Metal fluxes at the sediment–water interface in a free water surface constructed wetland

Metal biogeochemistry in the sediment, water, and the sediment–water interface (SWI) was studied in a free water surface constructed wetland. Concentrations of labile copper (Cu), zinc (Zn), sulfate, chloride, and dissolved organic carbon (DOC) were measured with the diffusive gradients in thin film (DGT) and peeper. A good agreement between peeper- and DGT-measured metals was observed for Cu (regression r 2 = 0.3, 95% CI of the slopes > 0), but not for Zn (95% CI of the slopes overlapped with 0), which was attributed to the different complexed compounds between Cu and Zn in porewater. The depth profile of labile metals in sediment porewater varied with time and was consistent with the solid-phase metal deposition, showing higher concentrations in the surface layer (3 to –3 cm) than in the bottom layer (–4 to –13 cm). The depth-averaged labile Cu and Zn concentrations measured by DGT were 1.0 and 3.1 µg/L, and labile sulfate, chloride, and DOC concentrations measured by peeper were 1.8, 3.6, and 2.1 mg/L, respectively. A sharp decrease in sulfate occurred in September when sulfate concentrations became the lowest among sampling months. This was caused by the seasonal sulfur cycles in the wetland, where the dominant sulfur reaction is sulfate reduction in warm seasons and sulfide oxidation in cold seasons. Different metal-removal mechanisms were observed in the two wetland cells; sulfur dynamics controlled the removal processes in the cell without frequent disturbance but failed to influence metal removal in the cell with frequent disturbance due to the interruption of anoxic layers. The flux ratios that compare labile element concentrations between the water column and the SWI (R-Cu, R-Zn, R-DOC, R-sulfate, and R-chloride) were generated to determine metal diffusive fluxes at the interface. Labile Zn was mostly transported from the water to the SWI during all seasons (R-Zn < 1 for all months except January). Labile Cu moved from the SWI to the water during the warm months (R-Cu < 1), which was explained by the bioturbation-induced transport of organic matter based on the positive correlations between R-Cu and R-DOC. In general, sediment can serve either as a sink or a source depending on the environmental conditions, metal speciation, and presence of living organisms. Here, metal flux at the SWI is a key component in the biogeochemical cycling of a constructed wetland.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

The practice and economics of hybrid poplar biomass production for biofuels and bioproducts in the Pacific Northwest

Hybrid poplar demonstration-scale farms were managed in Oregon, Washington, Idaho, and California to establish management practices, yields, harvesting methods, and the economics of biomass production. Yield during the 2-year establishment cycle averaged 3.5 dry Mg ha –1 year –1 increasing to 11.6 Mg ha –1 year –1 in the ensuing 3-year coppice cycle. Populus deltoides (Bartram ex Marsh.) × P. maximowiczii (Henry) varieties preformed best in Oregon during the coppice cycle with the best variety producing 18.1 Mg ha –1 year –1 , while P. ×generosa (Henry) varieties maximized yields in Washington at 22.1 Mg ha –1 year –1 . P. ×canadensis (Moench) varieties excelled in Idaho and California with upper yields of 13.6 Mg ha –1 year –1 and 12.9 Mg ha –1 year –1 , respectively. Stands were cut with a single-pass harvester 2 years after planting and a second time after 3 years of coppice growth; material capacity, limited by poor ground conditions, varied between 21.7 to 31.3 green Mg h –1 . Chemical composition averaged 1.87% inorganics, 7.74% extractives, 26.90% lignin, 38.07% glucan, 13.66% xylan, 1.61% galactan, 1.14% arabinan, and 2.76% mannan. Production costs (USD) projected over a 20-year rotation of six coppice cycles were $71.81 Mg –1 in Washington, $89.91 Mg –1 in Oregon, $98.76 Mg–1 in Idaho, and 179.07 Mg–1 in California. Here, land rental, establishment, crop care, harvest, transportation, and land restoration, respectively, accounted for 23%, 5%, 19%, 30%, 17%, and 6% of total feedstock cost. Farms were successfully restored to conditions existing before poplar conversion. In the absence of fertilization, increases in soil pH and decreases in nitrate-nitrogen, zinc, iron, and organic matter were consistently noted but could not be associated with poplar production alone.

09 BIOMASS FUELS↗
DOE OSTI2023

On Energy Storage Chemistry of Aqueous Zn-Ion Batteries: From Cathode to Anode

Rechargeable aqueous zinc-ion batteries (ZIBs) have resurged in large-scale energy storage applications due to their intrinsic safety, affordability, competitive electrochemical performance, and environmental friendliness. Extensive efforts have been devoted to exploring high-performance cathodes and stable anodes. However, many fundamental issues still hinder the development of aqueous ZIBs. Here, we critically review and assess the energy storage chemistries of aqueous ZIBs for both cathodes and anodes. First, this review presents a comprehensive understanding of the cathode charge storage chemistry, probes the existing deficiencies in mechanism verification, and analyzes contradictions between the experimental results and proposed mechanisms. Then, a detailed summary of the representative cathode materials and corresponding comparative discussion is provided with typical cases encompassing structural features, electrochemical properties, existing drawbacks, and feasible remedies. Subsequently, the fundamental chemical properties, remaining challenges, and improvement strategies of both Zn metal and non-Zn anodes are presented to thoroughly explore the energy storage chemistry of ZIBs and pursue the development of high-performance ZIBs. Furthermore, the progress of mechanistic characterization techniques and theoretical simulation methods used for ZIBs is timely reviewed. Finally, here we provide our perspectives, critical analysis, and insights on the remaining challenges and future directions for development of aqueous ZIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Chapter 20: Advances and Application of CRISPR-Cas Systems

A new gene-editing technique called clustered regularly interspaced short palindromic repeats (CRISPR) and CRISPR-associated (Cas) proteins have revolutionized genome engineering because of its high efficiency, relatively low cost, and ease of use compared with other techniques such as zinc-finger nucleases and transcription activator-like effector nucleases. CRISPR-Cas systems have transformed biological research, quickly becoming the preferred method for engineering specific genome sequences in industrially relevant microbes, important food crops, and human cells. This powerful new tool has the potential for limitless applications ranging from the treatment of human diseases to improving food security to the generation of renewable and sustainable bioproducts and biofuels. In this chapter, we will discuss advances and applications for these CRISPR-Cas systems in biological engineering.

bacterial↗
DOE OSTI2023

A high-performance lung-inspired ceramic 3D-printed heat exchanger for high-temperature energy-efficient systems

The thermal-to-electric conversion efficiency of next-generation supercritical carbon dioxide and concentrated solar power plants is significantly augmented by operating at temperatures exceeding 1000 °C if durable, compact, high-temperature heat exchangers (HXs) are developed. Whereas metal 3D-printed HXs fail to operate under extreme temperature conditions, ceramic 3D-printed HXs are deemed promising candidates for high-temperature, highly oxidizing environments. Ceramic 3D-printed HXs, however, exhibit a high gas permeability issue through hot and cold separating walls due to an excessive non-volatile photopolymer content utilized. Here, in this work, a novel leak-free lung-inspired ceramic 3D-printed HX employing a highly complex heat transfer topology is introduced for high-temperature energy-efficient systems. The high permeability issue of ceramic 3D-printed HXs is fully eliminated through a uniform zinc-based coating. It was determined that the effective thermal conductivity of the sintered ceramic heat exchangers is affected by the coated layer. The high-temperature thermal and hydraulic characteristics of the lung-inspired ceramic 3D-printed HX are comprehensively examined and compared against a millichannel 3D-printed HX module. Experimental results indicated that the lung-inspired 3D-printed ceramic HX significantly outperforms its millichannel counterpart. The lung-inspired HX shows a volume-based power density of 8.2 MW/m3 at a hot-side inlet air temperature of 700°C, a 71 % improvement compared with that of the millichannel HX. More importantly, the higher thermal duty of the lung-inspired 3D-printed HX is realized at a lower normalized pressure drop penalty of 510 Pa/W, 22 % lower than that of the millichannel ceramic HX. This study accelerates the advancement of high-performance ceramic 3D-printed HXs with complex topologies for high-temperature energy-efficient systems and/or corrosive environments.

42 ENGINEERING↗
DOE OSTI2023

Tetrazole-based inhibitors of the bacterial enzyme N -succinyl- L,L -2,6-diaminopimelic acid desuccinylase as potential antibiotics

Based on a hit from a high-throughput screen, a series of phenyltetrazole amides was synthesized and assayed for inhibitory potency against DapE from Haemophilus influenzae (HiDapE). The inhibitory potency was modest but confirmed, with the most potent analog containing an aminothiazole moiety displaying an IC 50 = 50.2 ± 5.0 μM. Finally, docking reveals a potential binding mode wherein the amide carbonyl bridges both zinc atoms in the active site, and the tetrazole forms key hydrogen bonds with Arg330.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Mechanoadaptive strain and functional osseointegration of dental implants in rats

Spatiotemporal implant-bone biomechanics and mechanoadaptive strains in peri-implant tissue are poorly understood. Physical and chemical characteristics of an implant-bone complex (IBC) were correlated in three-dimensional space (along the length and around a dental implant) to gather insights into time related integration of the implant with the cortical portion of a jaw bone in a rat. Rats (N = 9) were divided into three experimental groups with three rats per time point; 3-, 11-, and 24-day. All rats were fed crumbled hard pellets mixed with water (soft-food diet) for the first 3 days followed by a hard-food diet with intact hard-food pellets (groups of 11- and 24-day only). Biomechanics of the IBCs harvested from rats at each time point was evaluated by performing mechanical testing in situ in tandem with X-ray imaging. The effect of physical association (contact area) of a loaded implant with adapting peri-implant tissue, and resulting strain within was mapped by using digital volume correlation (DVC) technique. The IBC stiffness at respective time points was correlated with mechanical strain in peri-implant tissue. Results illustrated that IBC stiffness at 11-day was lower than that observed at 3-day. However, at 24-day, IBC stiffness recovered to that which was observed at 3-day. Furthermore, correlative microscopy and spectroscopy illustrated that the lower IBC stiffness was constituted by softer and less mineralized peri-implant tissue that contained varying expressions of osteoconductive elements. Lower IBC stiffness observed at 11-day was constituted by less mineralized peri-implant tissue with osteoconductive elements that included phosphorus (P) which was co-localized with higher expression of zinc (Zn), and lower expression of calcium (Ca). Higher IBC stiffness at 24-day was constituted by mineralized peri-implant tissue with higher expressions of osteoconductive elements including Ca and P, and lower expressions of Zn. These spatiotemporal correlative maps of peri-implant tissue architecture, heterogeneous distribution of mineral density, and elemental colocalization underscore mechanoadaptive physicochemical properties of peri-implant tissue that facilitate functional osseointegration of an implant. These results provided insights into 1) plausible "prescription" of mechanical loads as an osteoinductive "therapeutic dose" to encourage osteoconductive elements in the peri-implant tissue that would facilitate functional osseointegration of the implant; 2) a "critical temporal window" between 3 and 11 days, and perhaps it is this acute phase during which key candidate regenerative molecules can be harnessed to accelerate osseointegration of an implant under load.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

LABQ3: Bayesian method for quantification of mineral compositions and nano-scale elemental mapping of 3D synchrotron XCT data

Quantitative analysis of mineral compositions is essential in understanding geochemical, mineralogical and environmental processes. Fine-resolution 3D imaging is widely done using synchrotron X-ray computed tomography (XCT), but existing analyses are limited to visualization and segmentation. This paper presents a new method, Linear Attenuation Bayesian Quantitative 3D-mapper (LABQ3), based on the linearity of X-ray attenuation with respect to elemental concentrations. To address the random variability in attenuation measurements, LABQ3 employs Bayesian decision theory to minimize classification error, using reference attenuation distributions from scans of pure mineral standards. To demonstrate LABQ3 and test its performance, we studied precipitated carbonate samples. XCT scans were done at multiple energies using the transmission X-ray microscope (TXM) at beamline 32-ID-C of the Advanced Photon Source at Argonne National Laboratory. The reconstructed 3D images have a voxel size of 20 nm. Analyses revealed rich nano-scale compositional heterogeneity within individual particles. A mixture of calcium and cadmium produced an overall stoichiometric composition of (Ca 0.78 ,Cd 0.22 )CO 3 , with some voxels containing nearly pure CdCO 3 . The addition of zinc led to an overall stoichiometric composition of 33% Ca, 28% Cd, 39% Zn, with a nearly pure CaCO 3 core and compositional zonation through the rim. These compositional gradients are related to temporal sequences of carbonate mineral formation where Cd precipitated at the beginning in (Ca,Cd)CO 3 , while Cd and Zn precipitated at the end in (Ca, Cd,Zn)CO 3 . Results differ from bulk analyses using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS), showing that LABQ3 provides particle-specific insights. LABQ3 distinguishes itself by quantifying chemical compositions along a continuum, making it different from XCT analyses based on segmentation. LABQ3 allows simultaneous acquisition of morphology and chemical composition in 3D, facilitating the interpretation of chemical gradients of trace elements, quantification of solid solution compositions, inferences about temporal sequences of mineral precipitation, and addressing other concerns about solid-phase chemistry.

58 GEOSCIENCES↗
DOE OSTI2026

Entropy-defect synergy for dual luminescence mechanism in spinel: Time-resolved anti-counterfeiting and fingerprint visualization

Multimodal luminescent materials, while promising for anti-counterfeiting, often lack dynamic time-dependent responses and controllable spatial distribution, limiting their encryption capabilities in the spatiotemporal dimension. Here, this work presents a coordinated control strategy based on entropy and defect engineering, and uses a backpropagation (BP) neural network for material screening to successfully prepare spinel Mg 0.8 (Fe 0.04 Co 0.04 Ni 0.04 Cu 0.04 Zn 0.04 )Cr 2 O 4 (MgA 5 CO) phosphors with time-dependent dynamic luminescence behavior. This phosphor simultaneously activated the d-d transition luminescence (∼618 nm) derived from Co 2+ /Cr 3+ and the defect luminescence (∼398 nm) related to zinc vacancies (V Zn ) in a single-phase solid solution. The phosphor exhibits a time-dependent color evolution from pink to purple under fixed-wavelength excitation, due to the different excited-state dynamics and decay lifetimes associated with the d-d transition and defect luminescence. Structural characterization and spectral analysis confirmed the existence of V Zn and its significant role in defect luminescence process. The fluorescent and dynamic luminescent properties of entropy-based spinel oxide enable its use in advanced anti-counterfeiting applications like fingerprint recognition and color-changing dedicated anti-counterfeiting mark, showing promise in high-end and time-dynamic anti-counterfeiting fields. This research not only developed a new type of fluorescent dynamic anti-counterfeiting material, but also provided a new idea for constructing advanced optical functional materials with multiple luminescence mechanisms.

Defect project↗
DOE OSTI2021

Application of spectroscopic evidence to diffuse layer model (DLM) parameter estimation for cation adsorption onto ferrihydrite in single- and bi-solute systems

The diffuse layer model (DLM) is one of the most frequently used surface complexation models (SCM) for predicting cation adsorption onto ferrihydrite. However, the DLM with its existing database sometimes fails to predict cation adsorption, especially in multi-solute systems. Notably, the failure is often attributed to inaccurate selection of the surface complexes and/or underestimation of the site density for DLM formulation. DLM simulations of batch adsorption data conducted with cadmium, copper, lead, and zinc on ferrihydrite in CO2 free systems demonstrates the ability of the DLM to fit single-solute data reasonably well but highlights its limitations with respect to predicting bi-solute data. Modifications to the DLM were made in two steps. First, spectroscopic evidence was used to guide cation complexation reactions at the ferrihydrite surface. Second, surface characteristics (reactive site density, specific surface area, and acidity constants) of ferrihydrite were updated according to recent literature. The results from this study suggest that when spectroscopic verification is employed and surface site density is increased, a simple two-site DLM can predict cation adsorption on ferrihydrite in single-solute systems for pH data above 3.5 and in most of the bi-solute systems tested.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Visible-Light-Initiated Free-Radical Polymerization by Homomolecular Triplet-Triplet Annihilation

Polymerization reactions initiated by ultraviolet light are ubiquitous in scores of industrial applications but would markedly benefit from visible-light activation to overcome stability, energy consumption, light penetration, and sample geometry limitations. The current work leverages visible-light-driven homomolecular triplet-triplet annihilation (TTA) in zinc(II) meso-tetraphenylporphyrin (ZnTPP) to initiate facile free-radical polymerization in trimethylolpropane triacrylate (TMPTA) and methyl acrylate (MA) monomers through ultrafast electron transfer quenching. Selective Q-band (S 1 ) excitation of ZnTPP in the green or yellow sensitizes TTA occurring between two 3 ZnTPP* energized chromophores, ultimately generating the highly reducing S 2 excited state on one ZnTPP molecule (E red = –2.13 V versus saturated calomel electrode, SCE). Subsequently, this S 2 state engages in electron transfer with TMPTA or MA, thereby initiating the radical polymerization process. Bimolecular electron transfer was confirmed through optically gated fluorescence upconversion. In conclusion, FT-IR and EPR spin-trapping experiments verified visible-light-initiated polymerization leading to the formation of well-defined macro- and microscopic objects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Surviving nanoscale interfacial stability in extreme thermal expansion contrast Zn(CN) 2 -epoxy resin matrix composites

Here, we report the remarkable stability at the nanoscale matrix-filler interface in a series of overall low coefficient of thermal expansion (CTE) zinc cyanide (ZC)/epoxy resin composites. These interfaces demonstrate the stability of highly contrasting materials. These composites are designed to optimize the properties of both materials: epoxy resins are valued for their high strength, superb chemical resistance, low dielectric properties, and adhesive abilities. ZC, a model flexible framework, exhibits negative thermal expansion (NTE) behavior and compensates for the epoxy resin’s detrimentally large thermal expansion values. Filled resins minimize the native 65 ppm/°C CTE values to 19 ppm/° C over a wide temperature range while maintaining linearity, yielding composites compatible with typical metal and ceramic substrates’—commonly bonded to the resin— 0–20 ppm/° C CTE values. Additionally, with significant intrinsic differences in the materials, we use wide-angle X-ray diffraction and atomic force microscopy to elucidate thermal movement. The ZC/epoxy interface is surprisingly resilient over 1,000 cycles between -55° C and 75° C, extremes typical to aerospace applications. Further, we show that the resin viscosity remains less than 21 Pa*s at up to 30 vol% ZC, an important consideration for workability. We also discuss settling distribution, glass transition temperature, flexural strength, and longevity. All results point favorably towards practical implementation in low thermal expansion application needs: filling the gap in component design.

42 ENGINEERING↗
DOE OSTI2025

Silver diamine fluoride differentially affects dentin and hypomineralized enamel permeabilities

OBJECTIVES: To investigate the physicochemical effect of silver diamine fluoride (SDF) by correlating permeability with mineral density and elemental composition of hypomineralized enamel and carious dentin. METHODS: Enamel and dentin from human carious primary teeth with and without SDF treatment in-vivo, and hypomineralized enamel from permanent molars with and without SDF treatment in-vitro were scanned using micro X-ray computed tomography. Spatial maps of biometals (calcium, zinc), phosphorus, and silver were generated using X-ray fluorescence microprobe. Permeabilities were computed using Porous Microstructure Analysis software. RESULTS: The intrinsic permeability of SDF-treated carious dentin was 14.3 % lower than untreated sound dentin (6.39e-15 ± 3.01e-15 m² vs 7.46e-15 ± 1.82e-15 m²; P < 0.0001), while untreated carious dentin was 98.4 % higher (1.48e-14 ± 7.11e-15 m²; P < 0.0001). SDF-treated and untreated transparent dentin showed similar reduced permeabilities (75.6 % and 78.4 % lower than untreated sound dentin, respectively; P = 0.93). Severely hypomineralized enamel showed permeability reaching 108.1 % of adjacent sound dentin (5.71e-15 ± 2.04e-15 m² vs 5.28e-15 ± 1.30e-15 m²; P = 0.1409) and was significantly higher than mildly hypomineralized enamel (1.39e-15 ± 1.04e-15 m²; P < 0.0001). SDF treatment did not significantly impact the permeability of severely hypomineralized enamel (12.4 % reduction; P = 0.07). Principal component regression identified Zn level as a significant effector of tissue permeabilities in carious primary teeth (P < 0.0001). SIGNIFICANCE: This study introduces a computational method to measure dental tissue permeability, and demonstrates that SDF significantly reduces permeability in carious dentin but not intact hypomineralized enamel. The study reveals biometal Zn localization can alter dentin and enamel permeabilities, providing new insights into pathobiological mechanisms underlying caries and hypomineralization.

Chou, Conrad↗