Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wake fields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Neutral beams in two-ribbon flares and in the geomagnetic tail

The current sheet created in the wake of an erupting filament during a two-ribbon flare is studied. A comparison with the geomagnetic tail shows that the physics of these systems is very similar, and therefore the existence of super Dreicer fields and the generation of netural beams traveling down the postflare loops with small pitch angles may be expected. The observational evidence for neutral beams in flares is reviewed and found to be generally supportive, while contracting the widely held hypothesis of electron beams. A dimensional analysis further demonstrates that the results for self-consistent numerical simulations of the current sheet in the geomagnetic tail can directly be scaled to the coronal current sheet, and the scaling parameters are derived.

Martens, P. C. H.↗

DSMC simulation of ionized rarefied flows

Recently a renewed interest has been exhibited in understanding contamination and space environmental effect in the LEO range of 200 to 600 km as well as in low density microelectronics manufacturing technologies. Realistic simulations must model the physics of the highly coupled effects of neutral and charged particle flows, thermodynamic nonequilibrium, surface charging, and electromagnetic field effects. The computational requirements are enormous for this level of modeling and are almost impossible on current single processor supercomputers. An effort was initiated to develop this capability on a massively parallel MIMD supercomputers. The Wake Shield Facility experiment will be used for test case calculations. Preliminary results indicate that parallel supercomputers may be the only computers capable of simulating the required level of physics and spatial resolution. Calculations which contain from 1 to 8 million simulation particles are presented.

Bartel, Timothy J.↗

Experimental studies of flow separation of the GA(W)-2 airfoil at low speeds

Wind tunnel tests have been conducted on a NASA GA(W)-2 airfoil section at Reynolds number of 2.2 x 10(exp 6) and Mach number of 0.13. Detailed measurements of flow fields associated with turbulent boundary layers have been obtained at angles of attack of 10.3, 14.4, and 18.3 deg. Pre- and post-separated velocity and pressure survey results over the airfoil and in the associated wake are presented. Extensive force, pressure, tuft survey, hot-film survey, local skin friction, and boundary layer data are also included. Pressure distributions and separation point locations show good agreement with theory for the two lower angles of attack. Boundary layer displacement thickness, momentum thickness, and shape factor agree well with theory up to the point of separation. There is considerable disparity between extent of flow reversal in the wake as measured by pressure and hot-film probes. The difference is attributed to the intermittent nature of the flow reversal.

Seetharam, H. C.↗

A study of blade-vortex interaction aeroacoustics utilizing an independently generated vortex

This paper presents results from an experimental study of rotor blade-vortex interaction (BVI) aerodynamics and acoustics. The experiment utilized an externally generated vortex interacting with a two-bladed rotor operating at zero thrust to minimize the influence of the rotor's own wake. The rotor blades were instrumented with a total of 60 absolute pressure transducers at three spanwise and ten chordwise stations on both the upper and lower surfaces. Acoustic data were obtained with fixed near-field microphones as well as a movable array of far-field microphones. The test was carried out in the acoustically treated test section of the NASA Ames 80- by 120-foot Wind Tunnel. Several parameters which influences BVI, such as vortex-rotor separation distance, vortex strength, and vortex sense (swirl direction), as well as rotor tip Mach number and advance ratio, were varied. Simultaneous measurements were obtained of blade surface pressure distributions, near-field acoustics, and far-field acoustics during the vortex-blade encounters.

Kitaplioglu, C.↗

Transition and Turbulence Modeling for Blunt-Body Wake Flows

Aerobraking has been proposed as an efficient means of decelerating spacecraft for planetary missions. Most current aerobrake designs feature a blunt forebody shielding the payload from the intense heat generated during atmospheric entry. Although this forebody will absorb the largest portion of the heat pulse, accurate prediction of heating in the near wake is of great importance, since large local heating values can occur at points of shear-layer impingement. In order to address the various issues associated with these blunt-body wake flowfields, the Advisory Group for Aerospace Research and Development (AGARD) formed Working Group 18 in 1992. One of the objectives of this activity was to examine real-gas effects in high-speed flow fields around a 70 deg. blunted cone. To date, many researchers have conducted experiments using this geometry in various facilities, such as the Large Energy National Shock (LENS) tunnel at Cubric/Calspan and the HEG shock tunnel at DLR-Goettingen. Several computational studies have also been conducted in concert with these tests. Many of the experimental results have indicated the possible presence of a transitional shear layer through a large increase in heat transfer downstream of the reattachment point. The presence of transition could in fact lead to much higher peak heating than if the separated flow is entirely laminar or turbulent. In the shock-tunnel tests, however, it is difficult to separate such viscous-flow phenomena from real-gas effects. In order to help make this distinction, Horvath et al. recently conducted a set of experiments in the NASA Langley 20-Inch Mach 6 Tunnel, and compared the results to laminar Navier-Stokes calculations. They found heat-transfer distributions similar to those obtained in the high-enthalpy facilities, with the measured peak heating along the sting support markedly greater than that predicted by the laminar computations. These trends point to the need to find transitional and turbulent computational solutions for these flowfields.

Nance, Robert P.↗

Development of a Linearized Unsteady Euler Analysis with Application to Wake/Blade-Row Interactions

A three-dimensional, linearized, Euler analysis is being developed to provide a comprehensive and efficient unsteady aerodynamic analysis for predicting the aeroacoustic and aeroelastic responses of axial-flow turbomachinery blading. The mathematical models needed to describe nonlinear and linearized, inviscid, unsteady flows through a blade row operating within a cylindrical annular duct are presented in this report. A numerical model for linearized inviscid unsteady flows, which couples a near-field, implicit, wave-split, finite volume analysis to far-field eigen analyses, is also described. The linearized aerodynamic and numerical models have been implemented into the three-dimensional unsteady flow code, LINFLUX. This code is applied herein to predict unsteady subsonic flows driven by wake or vortical excitations. The intent is to validate the LINFLUX analysis via numerical results for simple benchmark unsteady flows and to demonstrate this analysis via application to a realistic wake/blade-row interaction. Detailed numerical results for a three-dimensional version of the 10th Standard Cascade and a fan exit guide vane indicate that LINFLUX is becoming a reliable and useful unsteady aerodynamic prediction capability that can be applied, in the future, to assess the three-dimensional flow physics important to blade-row, aeroacoustic and aeroelastic responses.

Verdon, Joseph M.↗

Linearized Unsteady Aerodynamic Analysis of the Acoustic Response to Wake/Blade-Row Interaction

The three-dimensional, linearized Euler analysis, LINFLUX, is being developed to provide a comprehensive and efficient unsteady aerodynamic scheme for predicting the aeroacoustic and aeroelastic responses of axial-flow turbomachinery blading. LINFLUX couples a near-field, implicit, wave-split, finite-volume solution to far-field acoustic eigensolutions, to predict the aerodynamic responses of a blade row to prescribed structural and aerodynamic excitations. It is applied herein to predict the acoustic responses of a fan exit guide vane (FEGV) to rotor wake excitations. The intent is to demonstrate and assess the LINFLUX analysis via application to realistic wake/blade-row interactions. Numerical results are given for the unsteady pressure responses of the FEGV, including the modal pressure responses at inlet and exit. In addition, predictions for the modal and total acoustic power levels at the FEGV exit are compared with measurements. The present results indicate that the LINFLUX analysis should be useful in the aeroacoustic design process, and for understanding the three-dimensional flow physics relevant to blade-row noise generation and propagation.

Verdon, Joseph M.↗

Compressibility and Turbulence Effects Due to Airfoil Clocking in Axial Compressors

Axial compressors have inherently unsteady flow fields because of relative motion between rotor and stator airfoils. This relative motion leads to viscous and inviscid (potential) interactions between blade rows. As the number of stages increases in a turbomachine, the buildup of convected wakes can lead to progressively more complex wake/wake and wake/airfoil interactions. Variations in the relative circumferential positions of stators or rotors can change these interactions, leading to different unsteady forcing functions on airfoils and different compressor efficiencies. In addition, as the Mach number increases the interaction between blade rows is intensified due to potential effects. The current study uses an unsteady, two-dimensional Navier-Stokes approach to investigate the unsteady aerodynamics of stator clocking in a 1-1/2 stage compressor, typical of high-pressure compressors used in advanced commercial jet engines. The effects of turbulence are modeled with both algebraic and two-equation models. Results include surface pressures, efficiencies, boundary layer quantities and turbulence quantities. In addition, the growth of turbulence and the effects of compressibility on airfoil are discussed.

Dorney, Daniel J.↗

PLASMA WAKE EXCITATION BY LASERS OR PARTICLE BEAMS

Plasma accelerators may be driven by the ponderomotive force of an intense laser or the space-charge force of a charged particle beam. Plasma wake excitation driven by lasers or particle beams is examined, and the implications of the different physical excitation mechanisms for accelerator design are discussed. Plasma-based accelerators have attracted considerable attention owing to the ultrahigh field gradients sustainable in a plasma wave, enabling compact accelerators. These relativistic plasma waves are excited by displacing electrons in a neutral plasma. Two basic mechanisms for excitation of plasma waves are actively being researched: (i) excitation by the nonlinear ponderomotive force (radiation pressure) of an intense laser or (ii) excitation by the space-charge force of a dense charged particle beam. There has been significant recent experimental success using lasers and particle beam drivers for plasma acceleration. In particular, for laser-plasma accelerators (LPAs), the demonstration at LBNL in 2006 of high-quality, 1 GeV electron beams produced in approximately 3 cm plasma using a 40 TW laser. In 2007, for beam-driven plasma accelerators, or plasma-wakefield accelerators (PWFAs), the energy doubling over a meter to 42 GeV of a fraction of beam electrons on the tail of an electron beam by the plasma wave excited by the head was demonstrated at SLAC. These experimental successes have resulted in further interest in the development of plasma-based acceleration as a basis for a linear collider, and preliminary collider designs using laser drivers and beam drivers are being developed. The different physical mechanisms of plasma wave excitation, as well as the typical characteristics of the drivers, have implications for accelerator design. In the following, we identify the similarities and differences between wave excitation by lasers and particle beams. The field structure of the plasma wave driven by lasers or particle beams is discussed, as well as the regimes of operation (linear and nonlinear wave). Limitations owing to driver emittance are also discussed.

43 PARTICLE ACCELERATORS↗

Field Sensitivity Analysis of Turbulence Model Parameters for Flow Over a Wing

Reynolds-averaged-Navier-Stokes (RANS) turbulence models are a critical tool in computational-fluid-dynamics simulations of aerodynamic systems, but simulation results can be highly sensitive to RANS-model parameter choices. Sensitivity analysis can be used to quantify these impacts, and the objective of this study is to demonstrate field sensitivity analysis with respect to ten parameters in the 2003 Menter shear-stress-transport (SST) turbulence model. Here, the analysis is demonstrated for an application relevant to wind energy, namely, flow over a NACA 0015 wing at 12 degree angle of attack and a Reynolds number of 1.5 x 10 6 . We quantify sensitivity using Sobol indices and the mean-squared gradient, which are estimated using polynomial chaos and active subspace models, respectively. Our results indicate that there are substantial spatial variations in parameter sensitivities, with different sets of most-sensitive parameters near the wing, as well as in the downstream wake, consistent with the physical interpretations of the turbulence model inputs. We show that, for this particular turbulence model and flow, simultaneous dimension reduction is possible across all quantities of interest, enabling efficient exploration of model outcomes. Ultimately, this analysis provides new insights into turbulence model parameter sensitivities in incompressible flows, and also demonstrates the implementation of field sensitivity analysis for applications relevant to aerodynamics simulations.

17 WIND ENERGY↗

Analysis of Performance Instabilities of Hafnia-Based Ferroelectrics Using Modulus Spectroscopy and Thermally Stimulated Depolarization Currents

The discovery of the ferroelectric orthorhombic phase in doped hafnia films has sparked immense research efforts. Presently, a major obstacle for hafnia's use in high-endurance memory applications like nonvolatile random-access memories is its unstable ferroelectric response during field cycling. Different mechanisms are proposed to explain this instability including field-induced phase change, electron trapping, and oxygen vacancy diffusion. However, none of these is able to fully explain the complete behavior and interdependencies of these phenomena. Up to now, no complete root cause for fatigue, wake-up, and imprint effects is presented. In this study, the first evidence for the presence of singly and doubly positively charged oxygen vacancies in hafnia–zirconia films using thermally stimulated currents and impedance spectroscopy is presented. Moreover, it is shown that interaction of these defects with electrons at the interfaces to the electrodes may cause the observed instability of the ferroelectric performance.

36 MATERIALS SCIENCE↗

Predicting wind farm operations with machine learning and the P2D‐RANS model: A case study for an AWAKEN site

Abstract The power performance and the wind velocity field of an onshore wind farm are predicted with machine learning models and the pseudo‐2D RANS model, then assessed against SCADA data. The wind farm under investigation is one of the sites involved with the American WAKE experimeNt (AWAKEN). The performed simulations enable predictions of the power capture at the farm and turbine levels while providing insights into the effects on power capture associated with wake interactions that operating upstream turbines induce, as well as the variability caused by atmospheric stability. The machine learning models show improved accuracy compared to the pseudo‐2D RANS model in the predictions of turbine power capture and farm power capture with roughly half the normalized error. The machine learning models also entail lower computational costs upon training. Further, the machine learning models provide predictions of the wind turbulence intensity at the turbine level for different wind and atmospheric conditions with very good accuracy, which is difficult to achieve through RANS modeling. Additionally, farm‐to‐farm interactions are noted, with adverse impacts on power predictions from both models.

17 WIND ENERGY↗

Multimode turbulent flow measurements using magnetic resonance imaging- and laser-based techniques and computational fluid dynamics simulations

We studied the flow field characteristics of a turbulent flow over a regularized cube array with a perpendicular injection flow through the floor between the second and third cubical elements, representing the complex flow interactions of a 3D jet and the wake flows behind cubical obstacles. Four different experimental measurements were performed: two magnetic resonance imaging-based measurements for three-dimensional three-component velocity (MRV) and concentration (MRC) and two laser-based techniques, particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF), for two-dimensional two-component velocity and concentration measurement, respectively. The mainstream Reynolds number is Re = 15 000⁠, based on the primary inlet velocity U m and channel height D H ⁠, whereas the injector Reynolds number is Re j = 3400⁠, based on the injector velocity U j and the injector's exit width D j ⁠. Numerical simulations were performed for the studied flow configuration of turbulent flow over a regularized cube array using Reynolds-averaged Navier–Stokes (RANS) and large-eddy simulation (LES) approaches. Results obtained from experimental measurements—including MRV, MRC, PIV, and PLIF—as well as RANS and LES simulations are discussed and compared along several horizontal and vertical planes of the studied configuration. In addition, 3D turbulent flow structures, such as leading-edge vortex, horseshoe vortex, and jet shear-layer vortex, and the isosurfaces of scalar concentration successfully revealed by MRV and MRC techniques were found to be in very good agreement with those 3D features extracted from RANS and LES simulations. In conclusion, the high-resolution experimental and numerical database obtained from this study could be useful for validation and verification of numerical codes.

Computational fluid dynamics↗

Experimental studies of flow separation of three airfoils at low speeds

Wind tunnel tests were conducted on the NASA LS(1)-0421 Mod, NACA 2412 and NASA GA(W)-2 airfoil sections at a Reynolds number of 2.2 x 10(6) and a Mach number of 0.13. Detailed measurements of flow fields associated with turbulent boundary layers of these airfoils were obtained at pre-stall, near-stall, and post-stall angles of attack. Velocity and pressure survey results over the airfoil and in the associated wake, are presented for fully attached flow conditions through the stalled flow condition. Extensive force, pressure, tuft survey, hot-film survey, local skin friction and boundary layer data are also included.

Rodgers, E. J.↗

Degradation of Spacesuit Fabrics in Low Earth Orbit

Six samples of pristine and dust-abraded outer layer spacesuit fabrics were included in the Materials International Space Station Experiment-7, in which they were exposed to the wake-side low Earth orbit environment on the International Space Station (ISS) for 18 months in order to determine whether abrasion by lunar dust increases radiation degradation. The fabric samples were characterized using optical microscopy, optical spectroscopy, field emission scanning electron microscopy, atomic force microscopy, and tensile testing before and after exposure on the ISS. Comparison of pre- and post-flight characterizations showed that the environment darkened and reddened all six fabrics, increasing their integrated solar absorptance by 7 to 38 percent. There was a decrease in the ultimate tensile strength and elongation to failure of lunar dust abraded Apollo spacesuit fibers by a factor of four and an increase in the elastic modulus by a factor of two.

Gaier, James R.↗

A Comparison of ARTEMIS Data with the Lunar Plasma Design Environment for NASA Crewed Missions

NASA’s Gateway will provide the capability for sustaining a human presence in cis-lunar space. Operations of the Gateway will include spacecraft dockings, extra vehicular activities (EVA), and high-power solar arrays. NASA’s experience with the International Space Station highlighted the importance of evaluating spacecraft charging effects for such operations. For crewed spacecraft, which tend to employ the use of dielectric surfaces in this dynamic plasma environment, reliance on spacecraft charging simulation packages, such as the NASA/Air Force Spacecraft Charging Analyzer Program (Nascap-2k) [Mandell et al., 2006] and Spacecraft Plasma Interaction System (SPIS) [Roussel et al., 2008], is required to understand the risks to hardware and humans. The variability in the lunar plasma environment as the Moon revolves around the Earth, lunar wake effects, and a strong dependency on photoemission and secondary electron emission creates challenges for spacecraft charging analysis. The Design Specification for Natural Environments (DSNE) [NASA, MSFC] is the primary resource for space environments affecting NASA’s crewed missions, and the DSNE provides plasma environments in a standard form for input into simulation packages. NASA developed the existing lunar plasma environment using data from Geotail [Nishida, 1994] along with published lunar plasma wake models [Halekas et al., 2005] based on Lunar Prospector. Since 2011, NASA’s twin Acceleration Reconnection Turbulence & Electrodynamics of Moon’s Interaction with the Sun (ARTEMIS) satellites [Angelopoulos, 2010] have been collecting high resolution plasma and fields observations within the lunar plasma environment providing a much larger dataset of the plasma properties in cislunar space. This research compares the existing lunar plasma environment definition with ARTEMIS data and makes recommendations on the refinement of the environment definition for future lunar missions.

ARTEMIS mission↗

Kestrel Results at Liftoff Conditions for a Space Launch System Configuration in Proximity to the Launch Tower

Aerodynamic data books for Space Launch System vehicles require databases for the integrated forces and moments and section loads during liftoff and transition to the ascent phase of flight. While the force and moment database can be generated from wind tunnel results, computational analyses are necessary to provide the extensive surface information required to generate proper lineloads. Of the two flight regimes, the liftoff problem is the more costly and complex situation to simulate, as it requires modeling of the vehicle in proximity to the launch tower. The effects of massive separation on the leeward pressure fields of both the tower and vehicle are not well captured with RANS methods, necessitating the use of more advanced methods, such as Delayed Detached Eddy Simulation, in conjunction with computational grids sufficiently refined to resolve the wakes. Details on the computational setup for employing the Kestrel flow solver to address the liftoff problem are presented. The methodology involves the use of independent unstructured near-body grids for the vehicle and the tower, overset by a solution adaptive Cartesian off-body grid. Results from the simulations are compared to experimental results from a test in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel.

Computational fluid dynamics↗

Measurements and modeling of flow structure in the wake of a low profile wishbone vortex generator

The results of an experimental examination of the vortex structures shed from a low profile 'wishbone' generator are presented. The vortex generator height relative to the turbulent boundary layer was varied by testing two differently sized models. Measurements of the mean three-dimensional velocity field were conducted in cross-stream planes downstream of the vortex generators. In all cases, a counter-rotating vortex pair was observed. Individual vortices were characterized by three descriptors derived from the velocity data; circulation, peak vorticity, and cross-stream location of peak vorticity. Measurements in the cross plane at two axial locations behind the smaller wishbone characterize the downstream development of the vortex pairs. A single region of stream wise velocity deficit is shared by both vortex cores. This is in contrast to conventional generators, where each core coincides with a region of velocity deficit. The measured cross-stream velocities for each case are compared to an Oseen model with matching descriptors. The best comparison occurs with the data from the larger wishbone.

Wendt, B. J.↗