Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructure and mechanical properties of ultrasonic spot welding of AA7075-T6 and A380 casting aluminum alloy

Ultrasonic spot welding (USW) was employed to join AA7075-T6 and casting Al alloy A380. Under a constant welding power, the influence of the welding time duration (from 1 s to 3 s) on peak temperature, microstructure, hardness, and mechanical strength of the joints were studied. It was found that the peak temperature increased with welding time. A sound solid-state metallurgical bonding was obtained at the joint interface. The cracks occurred at the edge of the joints were eventually eliminated as the welding time increased. A layer of refined grains formed in A380 adjacent to the bonding line. Further, hardness reduction occurred in AA7075 at the joint interface and the degree of hardness reduction and the volume increased with the peak temperature. By increasing welding time, lap shear tensile tests show that the peak load increased from 5.3 kN to 6.55 kN. The corresponding interfacial shear strength ranged from 96.29 MPa to 99.72 MPa, lower than the shear strength of both base materials (331 MPa for AA7075 and 185 MPa for A380). All joint samples exhibited interfacial fracture after lap shear tensile testing, with a thin layer of A380 remnant attached to AA7075 at the center of the fractured surface.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Joining Light Metals with Polymer Composites Through Metal Overcasting

This work investigates a unique technique to join aluminum (Al) and magnesium (Mg) alloys to carbon fiber reinforced polymer (CFRP) composites without the use of adhesives or mechanical fasteners. The joints were made using an overcasting technique where the molten alloys were cast around the polymer composites using high pressure die casting method. Rapid cooling during casting allowed the composite to be embedded inside the cast metal without causing any gross damage to the former even though the molten metal temperature exceeded the melting point of the composite matrix by several 100’s of deg. C. The metal/composite interface was examined using optical microscopy and x-ray imaging and the joint strength was examined through tensile testing. Although evidence of polymer melting was evident in the x-ray images, the embedded section of the composite coupons retained their overall shape and integrity. Preliminary tension tests on Al/CFRP composites showed strength degradation of the CFRP and it failed near the metal/CFRP interface (outside the joint). Strength degradation in the CFRP suggests that the overcasting process needs further optimization to minimize thermal excursion in the CFRP. Nevertheless, the overcasting process shows great promise as a unique joining technique with application in fabricating light-weight structures for automotive and transportation industries.

overcasting, Casting, Mg Castings, Al Casting, Joi↗
DOE OSTI2023

Analysis of ultrafast magnetization switching dynamics in exchange-coupled ferromagnet–ferrimagnet heterostructures

Magnetization switching in ferromagnets has so far been limited to the current-induced spin–orbit–torque effects. Recent observation of helicity-independent all-optical magnetization switching (HI-AOS) in an exchange-coupled ferromagnet–ferrimagnet (FM-FEM) heterostructures expanded the range and applicability of such ultrafast heat-driven magnetization switching. Here we report the element-resolved HI-AOS dynamics of such an exchange-coupled system, using a modified microscopic three-temperature model. We have studied the effect of (i) the Curie temperature of the FM, (ii) FEM composition, (iii) the long-range Ruderman–Kittel–Kasuya–Yosida (RKKY) exchange-coupling strength, and (iv) the absorbed optical energy on the element-specific time-resolved magnetization dynamics. The phase-space of magnetization illustrates how the RKKY coupling strength and the absorbed optical energy influence the switching time. Our analysis demonstrates that the threshold switching energy depends on the composition of the FEM and the switching time depends on the Curie temperature of the FM as well as RKKY coupling strength. Importantly, this simulation anticipates new insights into developing faster and more energy-efficient spintronics devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crystal plasticity modeling for the strengthening effect of multilayered copper–graphene nanocomposites

The paper explores plastic deformation mechanisms in metal–graphene nanocomposites, illustrating their material strengthening effects through a crystal plasticity finite element (CPFE) model. This model is compared with published experimental results, which have previously shown that the two-dimensional shape of graphene effectively controls dislocation motion and significantly enhances the strength of metals. Simulated nanopillar compression tests, using a physics-based CP model that incorporates surface nucleation and single-arm source dislocation mechanisms, help us understand dislocation motions at submicron length scales. The crystal plasticity models are applied to nanolayered composites with copper grain layers and monolayer graphene, featuring repeat layer spacings of 200 nm, 125 nm, and 70 nm, respectively. This study quantifies the accumulation of dislocations at the graphene interfaces, contributing to the ultra-high strength of copper–graphene composites. Furthermore, a Hall–Petch-like correlation is established between yield strength and the number of embedded graphene layers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A snapshot of high-entropy alloy processing techniques and their effects on resulting mechanical properties

High-entropy alloys (HEAs) exhibit exceptional strength, corrosion resistance, and thermal stability, making them promising candidates for nuclear, aerospace, and other extreme applications. While most prior work has focused on compositional design, manufacturing techniques themselves can alter microstructure and mechanical properties as dramatically as alloy chemistry. This review compiles and compares the effects of processing routes—including arc melting, induction melting, mechanical alloying with spark plasma sintering, and additive manufacturing—on the structure and properties of HEAs. Quantitative comparisons highlight, for example, that SPS-processed alloys can achieve ∼20–45 % higher yield and tensile strength than arc-melted counterparts, while Bridgman solidification produces nearly single-crystal structures with elongation to failure exceeding 80 %. Additive manufacturing routes such as selective laser melting offer fine microstructures but also introduce anisotropy and porosity, leading to yield strengths spanning 100–600 MPa for the same composition. By synthesizing such results, this review provides actionable insight into how processing routes interact with HEA core effects (high entropy, lattice distortion, sluggish diffusion, and cocktail effect) to determine performance, thereby offering a practical guide for optimizing manufacturing strategies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain size on iron-boride nanoglasses

Metallic nanoglasses are made of amorphous grains that are separated by lower-density amorphous boundaries, which have been proposed to enhance plasticity through the deflection of cracks and shear bands at interfaces. It has been difficult to experimentally control grain size and interfacial structure to understand their roles in plastic deformation. Here, we fabricate bulk nanoglasses via compaction and sintering of colloidally synthesized amorphous iron-boride nanoparticles. These nanoglasses have amorphous grains with diameters from 116nm to 576nm and were tested using nanoindentation and micropillar compressions. The nanoglass with a grain size of 576 nm shows the highest elastic modulus and hardness of 101 GPa and 7.4GPa, respectively. Transmission electron microscopy reveals that nanocrystals form within the nanoglasses during compaction. Higher nanocrystal density correlates with higher nanoparticle crystallization enthalpy, an increase in plasticity, and a decrease in yield strength. Plastic strain of 5.0%, yield strength of 3.8GPa, and ultimate compressive strength of 2.7–3.8GPa were achieved. Here we show that the compaction of colloidal metallic glass nanoparticles results in robust bulk samples, with mechanical properties similar to that of other iron-based bulk metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical behavior of additively manufactured and wrought 316L stainless steels before and after neutron irradiation

Fabrication of nuclear reactor components using additive manufacturing (AM) methods is now a practical option since the AM technologies have advanced to allow for building of complex parts with high quality materials. To assess the mechanical performance of printed components in reactor-relevant conditions and to build a property database for the AM 316L stainless steel (SS), mechanical testing and characterization were performed before and after neutron irradiation. In this work, miniature tensile specimens were irradiated at the High Flux Isotope Reactor (HFIR) to 0.2 and 2 displacements per atom (dpa) at 300 and 600°C. The AM 316L SS was tested in the as-built, stress-relieved, and solution-annealed conditions, and the wrought (WT) 316L SS in solution-annealed condition as a reference alloy. The baseline test result showed that the AM 316L SS, regardless of the post-build heat treatment, had higher strength than the WT 316L SS, but similar ductility. Post-irradiation tensile testing was conducted at RT, 300°C, and 500°C for selected irradiation conditions. Neutron irradiation induced significant changes in the mechanical behavior of the AM stainless steels, including both hardening and softening. Although the as-built 316L steel after 300°C irradiation showed necking just after yielding, the overall property changes of the as-printed alloy became less significant after 600°C irradiation. Irradiation-induced ductilization was also observed after the higher temperature irradiation. In general, the strength change was smaller in the relatively stronger as-built and stress-relieved AM SSs than in the solution-annealed AM and WT SSs. These relatively lower strength 316L SSs overall retained higher ductility in the irradiation conditions tested, but the stronger 316L SSs demonstrated a similar level of ductility after the higher temperature (600°C) irradiation. It is a positive assessment for the AM 316L materials that no embrittlement was observed within the test and irradiation conditions of the experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗
DOE OSTI2022

Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils

In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Phase stability, mechanical properties, and ion irradiation effects in face-centered cubic CrFeMnNi compositionally complex solid-solution alloys at high temperatures

We report two CrFeMnNi face-centered cubic complex concentrated solid-solution alloys (CSA) have been evaluated for phase stability, mechanical properties, and radiation damage effects from heavy ions. Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 were predicted by thermodynamic calculations to phase separate and maintain a single phase at 700 °C, respectively. Aging experiments at this temperature confirmed varying degrees of precipitation of a body-centered cubic phase in both Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 . The alloys showed promising strength in tensile deformation at room temperature, with yield strengths of 155 MPa and 151 MPa for Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe3 5 Mn 15 Ni 35 , respectively. At 500 °C, the yield strength of Cr 18 Fe 27 Mn 27 Ni 28 fell to 93 MPa, and to 100 MPa in Cr 15 Fe3 5 Mn 15 Ni 35 . Unlike Cr 18 Fe 27 Mn 27 Ni 28 , Cr 15 Fe 35 Mn 15 Ni 35 gained some ductility at 500 °C compared to room temperature. The two CSAs were irradiated to 75 dpa at 500 °C in the plateau region of the displacement curve using 3.7 MeV Ni 2+ ions, alongside model alloy 709 as a reference. Irradiation results produced similar densities and sizes of dislocations loops in the two CSAs compared to the reference. However, while large voids form in the plateau region of Cr 18 Fe 27 Mn 27 Ni 28 , small voids form just beyond the displacement peak of Cr 15 Fe 35 Mn 15 Ni 35 . Atom probe tomography and energy dispersive X-ray spectroscopy-equipped scanning transmission electron microscopes were used to characterize the alloys for changes in chemical distribution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Failure evaluation of neutron-irradiated SiC/SiC composites by underwater acoustic emission

Here, understanding the statistical properties of mechanical properties of non-irradiated and neutron-irradiated SiC/SiC composites is essential for component design. This study aims to evaluate the detailed damage accumulation behavior of composites focusing on two fracture parameters: proportional limit stress (PLS) and acoustic emission (AE) onset stress. The developmental underwater AE technique, which is benefit in non-contact in-situ failure monitoring method during mechanical testing and in handle of the irradiated material, was first applied to evaluate damage accumulation behavior. Two types of chemical vapor infiltration SiC/SiC composites were used: one reinforced with Hi-Nicalon Type-S SiC fiber and one reinforced with Tyranno-SA3 SiC fiber in the form of satin-woven 2D fabrics with pyrolytic carbon interface. Neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory reached a fluence of 30 dpa at a temperature of 620–670°C. Four-point flexural tests were conducted to evaluate post-irradiation strength. Weibull statistics did not suggest marked degradation of composite strength. Detailed failure behavior evaluated by AE demonstrated no irradiation-induced change of the AE onset stress (i.e., crack initiation equivalent stress). Failure probability analysis suggests that increasing the reliability of composites (i.e., the Weibull modulus rather than strength itself) is essential to expanding the design margin and benefiting from a probabilistic design approach.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Achieving superior mechanical properties: Tailoring multicomponent microstructure in AISI 9254 spring steel through a two-stage Q&P process and nanoscale carbide integration

In the pursuit of lightweight, durable steel, we have successfully developed a multicomponent structure in AISI 9254 spring steel using a two-stage quenching and partitioning (Q&P) process. The primary objective of this process was to engineer an optimized microstructure consisting of nanobainite, martensite, and nano-carbides. Utilizing the insights gained from the results of advanced techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom probe tomography (APT) performed on the as-received AISI 9254 spring steel, we refined the quenching and partitioning (Q&P) path, leading to the successful establishment of a bainitic transformation for superior mechanical properties. Our tensile tests revealed a high yield strength (≈ 1600 ± 25 MPa) and ultimate tensile strength (≈ 1850 ± 50 MPa), along with considerable elongation (≈ 11.15 ± 0.25%). We also identified that pre-formed martensite lath defects and high silicon content play crucial roles during the Q&P process, preventing carbide coalescence and increasing strain-hardening capacity. Finally, this study demonstrates the potential of a Q&P process to generate high-strength, ductile steel for automotive and aerospace applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Deformation behavior of annealed Cu64Zr36 metallic glass via molecular dynamics simulations

In the present work, we investigate the isothermal annealing process of Cu 64 Zr 36 metallic glass (MG) by means of molecular dynamics (MD) simulations, and characterize the compression properties under different temperatures and compressive rates. The pair distribution functions, the bond-orientational order, and the cluster-type index method are modeled and analyzed to characterize changes in the structure. Results of the modeling and analysis reveal that the MgZn 2 -type Laves, MgCu 2 -type Laves and five-fold local symmetry structures can be formed during the isothermal holding at 950 K. Study on the compression properties shows that at a fixed strain rate, the yield strength and yield drop all increase with decreasing temperature. At a fixed temperature, however, the increase of the strain rate leads to a noticeable increase in the yield strength at 600 K, but has little effect on yield strength at 10 K. Moreover, the modeling and analysis of the structure at a temperature of 10 K and strain-rate of 5 × 10 7 s -1 demonstrate that the order-disorder transformation initiates the shear band.

36 MATERIALS SCIENCE↗