Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “particle data analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

New Particle Formation and Growth to Climate‐Relevant Aerosols at a Background Remote Site in the Western Himalaya

New particle formation (NPF) can influence the Earth's radiative budget when the newly formed particles grow to climate‐relevant sizes. Here, we present analysis of 21 months of continuous aerosol size distribution measurements at a background remote site in the western Himalaya and provide observational evidence that newly formed particles grow to cloud condensation nuclei (CCN)‐active sizes (i.e., >20–100 nm in diameter). Out of total 55 NPF events, 38 (66%) events occurred in the pre‐monsoon season (March–May). NPF events were classified into those with and without pollution influence as polluted and cleaner, respectively, using black carbon data. The analysis of air mass age, based on the ratio of number concentration of Aitken to accumulation mode aerosols, indicated that NPF occurred in the relatively cleaner air masses reaching to the site. The median formation rate of 10 nm particles and particle growth rates for cleaner events were three‐fold and two‐fold, respectively, higher than polluted events. We present the first estimates of the survival probability of newly formed particles to 50 and 100 nm size, which was not attempted in an Indian environment previously. The survival probability to 50 nm particles ranged from 44% to 98%, with a mean and standard deviation of 82 ± 18%. On average, ∼60% of the particles surviving to 50 nm survived to 100 nm, making the overall survival probability of 100 nm to 53 ± 31%. This indicates that the probability of nucleated particles growing to CCN‐active sizes under a large source of condensing vapor (transported from nearby lower‐altitude regions) and low pre‐existing particle concentrations (background mountain site) is high compared to the previous studies. These findings highlight the importance of the efficiency of nucleation events for producing CCN, which is a critical basis of aerosol indirect effects.

cloud condensation nuclei↗

Elemental Mixing State of Aerosol Particles Collected in Central Amazonia during GoAmazon2014/15

Two complementary techniques, Scanning Transmission X-ray Microscopy/Near Edge Fine Structure spectroscopy (STXM/NEXAFS) and Scanning Electron Microscopy/Energy Dispersive X-ray spectroscopy (SEM/EDX), have been quantitatively combined to characterize individual atmospheric particles. This pair of techniques was applied to particle samples at three sampling sites (ATTO, ZF2, and T3) in the Amazon basin as part of the Observations and Modeling of the Green Ocean Amazon (GoAmazon2014/5) field campaign during the dry season of 2014. The combined data was subjected to k-means clustering using mass fractions of the following elements: C, N, O, Na, Mg, P, S, Cl, K, Ca, Mn, Fe, Ni, and Zn. Cluster analysis identified 12 particle types, across different sampling sites and particle sizes. Samples from the remote Amazon Tall Tower Observatory (ATTO, also T0a) exhibited less cluster variety and fewer anthropogenic clusters than samples collected at the sites nearer to the Manaus metropolitan region, ZF2 (also T0t) or T3. Samples from the ZF2 site contained aged/anthropogenic clusters not readily explained by transport from ATTO or Manaus, possibly suggesting the effects of long range atmospheric transport or other local aerosol sources present during sampling. In addition, this data set allowed for recently established diversity parameters to be calculated. All sample periods had high mixing state indices (χ) that were >0.8. Two individual particle diversity (D i ) populations were observed, with particles <0.5 μm having a D i of ~2.4 and >0.5 μm particles having a D i of ~3.6, which likely correspond to fresh and aged aerosols respectively. The diversity parameters determined by the quantitative method presented here will serve to aid in the accurate representation of aerosol mixing state, source apportionment, and aging in both less polluted and more industrialized environments in the Amazon Basin.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Using deep machine learning to interpret proton radiography data from a pulsed power experiment

Deep machine learning is used to analyze a proton radiograph from a tin pulsed power experiment and determine density values for each pixel in the image. Two promising convolutional neural network architectures that have proven to be effective for image analysis in other applications are applied to analyze a proton radiograph and find density values. The process of creating a suitable training dataset is described, involving the Lagrangian hydrodynamic model used for simulations of the experiment, the proton radiography forward model to make synthetic images for training, and the manner in which data augmentation is used to expand the resulting image dataset. It is shown that machine learning not only produces a reasonable density field but is also able to predict features in the density field that are suggested by the proton radiograph but not captured by simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Using Synchrotron X-ray Fluorescence Microprobes in the Study of Metal Homeostasis in Plants

Background and Aims: This Botanical Briefing reviews the application of synchrotron X-ray fluorescence (SXRF) microprobes to the plant sciences; how the technique has expanded our knowledge of metal(loid) homeostasis, and how it can be used in the future. Scope: The use of SXRF microspectroscopy and microtomography in research on metal homeostasis in plants is reviewed. The potential use of SXRF as part of the ionomics toolbox, where it is able to provide fundamental information on the way that plants control metal homeostasis, is recommended. Conclusions: SXRF is one of the few techniques capable of providing spatially resolved in-vivo metal abundance data on a sub-micrometre scale, without the need for chemical fixation, coating, drying or even sectioning of samples. This gives researchers the ability to uncover mechanisms of plant metal homeostasis that can potentially be obscured by the artefacts of sample preparation. Further, new generation synchrotrons with smaller beam sizes and more sensitive detection systems will allow for the imaging of metal distribution within single living plant cells. Even greater advances in our understanding of metal homeostasis in plants can be gained by overcoming some of the practical boundaries that exist in the use of SXRF analysis.

43 PARTICLE ACCELERATORS↗

Potentials for J/{psi} from b decays measurement in the ALICE experiment at LHC

The ALICE potentials in proton-proton collisions for the measurement of the fraction of J/{psi} produced at central rapidity (|y|<0.9) in beauty hadrons semi-inclusive decays, namely B{yields}J/{psi}X, is discussed.This measurement relies on the combined use of the Time Projection Chamber (TPC), for tracking and particle identification via dE/dx measurement; the Inner Tracking System (ITS) for tracking and detection of displaced vertices; the Transition Radiation Detector (TRD) for particle identification.The description of the analysis method developed and the discussion of the estimate for a total J/{psi} statistics corresponding to one year of ALICE data taking in p-p collisions at {radical}(s) = 7 TeV is provided in the article.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Resolving small signal measurements in experimental plasma environments using calibrated subtraction of noise signals

The performance of many diagnostic and control systems within fusion and other fields of research are often detrimentally affected by spurious noise signals. This is particularly true for those (such as radiation or particle detectors) working with very small signals. Common sources of radiated and conducted noise in experimental fusion environments include the plasma itself and instrumentation. The noise complicates data analysis, as illustrated by noise on signals measured with the heavy ion beam probe (HIBP) installed on the Madison Symmetric Torus. The noise is time-varying and often exceeds the secondary ion beam current (in contrast with previous applications). Analysis of the noise identifies the dominant source as photoelectric emission from the detectors induced by ultraviolet light from the plasma. This has led to the development of a calibrated subtraction technique, which largely removes the undesired temporal noise signals from data. The advantages of the technique for small signal measurement applications are demonstrated through improvements realized on HIBP fluctuation measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quantitative probing of the fast particle motion during the solidification of battery electrodes

Synchrotron x-ray tomography represents one of the most powerful imaging techniques that can visualize the three-dimensional microstructural complexity with a high spatial resolution. To date, however, the temporal resolution of this technique has been handicapped by the intrinsic limitations in the data acquisition speed and the lack of a suitable data processing method. The present study aims to fundamentally resolve this challenge by implementing a data analysis method that is based on differentiating discrete tomography reconstruction from a continuous scan reconstruction. With this methodological development, we capture and quantify the particle motion during the solidification of battery electrodes and reveal the statistics of the dynamically evolving motion in the drying process, which has been challenging to resolve. We discover that the particle motion exhibits a strong dependence on its geometric location within a drying electrode. Our results also imply that the final electrode quality can be controlled by balancing the solvent evaporation rate and the particle mobility in the region close to the drying surface.

25 ENERGY STORAGE↗

Saturn Ring Data Analysis and Thermal Modeling

CIRS, VIMS, UVIS, and ISS (Cassini's Composite Infrared Specrtometer, Visual and Infrared Mapping Spectrometer, Ultra Violet Imaging Spectrometer and Imaging Science Subsystem, respectively), have each operated in a multidimensional observation space and have acquired scans of the lit and unlit rings at multiple phase angles. To better understand physical and dynamical ring particle parametric dependence, we co-registered profiles from these three instruments, taken at a wide range of wavelengths, from ultraviolet through the thermal infrared, to associate changes in ring particle temperature with changes in observed brightness, specifically with albedos inferred by ISS, UVIS and VIMS. We work in a parameter space where the solar elevation range is constrained to 12 deg - 14 deg and the chosen radial region is the B3 region of the B ring; this region is the most optically thick region in Saturn's rings. From this compilation of multiple wavelength data, we construct and fit phase curves and color ratios using independent dynamical thermal models for ring structure and overplot Saturn, Saturn ring, and Solar spectra. Analysis of phase curve construction and color ratios reveals thermal emission to fall within the extrema of the ISS bandwidth and a geometrical dependence of reddening on phase angle, respectively. Analysis of spectra reveals Cassini CIRS Saturn spectra dominate Cassini CIRS B3 Ring Spectra from 19 to 1000 microns, while Earth-based B Ring Spectrum dominates Earth-based Saturn Spectrum from 0.4 to 4 microns. From our fits we test out dynamical thermal models; from the phase curves we derive ring albedos and non-lambertian properties of the ring particle surfaces; and from the color ratios we examine multiple scattering within the regolith of ring particles.

Saturn's rings↗

Sources of machine-induced background in the ATLAS and CMS detectors at the CERN Large Hadron Collider

One source of experimental background in the CERN Large Hadron Collider (LHC) is particles entering the detectors from the machine. These particles are created in cascades, caused by upstream interactions of beam protons with residual gas molecules or collimators. We estimate the losses on the collimators with SixTrack and simulate the showers with FLUKA and MARS to obtain the flux and distribution of particles entering the ATLAS and CMS detectors. We consider some machine configurations used in the first LHC run, with focus on 3.5 TeV operation as in 2011. Results from FLUKA and MARS are compared and a very good agreement is found. An analysis of logged LHC data provides, for different processes, absolute beam loss rates, which are used together with further simulations of vacuum conditions to normalize the results to rates of particles entering the detectors. We assess the relative importance of background from elastic and inelastic beam-gas interactions, and the leakage out of the LHC collimation system, and show that beam-gas interactions are the dominating source of machine-induced background for the studied machine scenarios. Our results serve as a starting point for the experiments to perform further simulations in order to estimate the resulting signals in the detectors.

Circular colliders↗

Analysis of LEAM experiment response to charged particles

The objectives of the Lunar Ejecta and Meteorites Experiment (LEAM) were to measure the long-term variations in cosmic dust influx rates and the extent and nature of the lunar ejecta. While analyzing these characteristics in the data, it was discovered that a majority of the events could not be associated with hypervelocity particle impacts of the type usually identified with cosmic dust, but could only be correlated with the lunar surface and local sun angle. The possibility that charged particles could be incident on the sensors led to an analysis of the electronics to determine if such signals could cause the large pulse height analysis (PHA) signals. A qualitative analysis of the PHA circuit showed that an alternative mode of operation existed if the input signal were composed of pulses with pulse durations very long compared to the durations for which it was designed. This alternative mode would give large PHA outputs even though the actual input amplitudes were small. This revelation led to the examination of the sensor and its response to charged particles to determine the type of signals that could be expected.

Perkins, D.↗

Colloidal Nafion Particles: Are Cylinders Ubiquitous?

Colloidal Nafion morphology plays a critical role in determining the performance of fuel cells and electrolyzers. While small-angle neutron scattering (SANS) studies previously described Nafion in liquid media as dispersed cylinders, the analysis remains nonunique with multiple possible morphological descriptions of the data. Here, using SANS and all-atomistic molecular dynamics, we confirm that Nafion morphology in liquid media differs substantially depending on dispersing agent and dispersion method. H + Nafion dispersed in N-methyl pyrrolidone forms swollen cluster particles with physically cross-linked ionic groups. Scattering profiles from dispersed Nafion membrane have a large structure factor feature not observed for redispersed Nafion D-521. H + Nafion dispersed in water has a highly elongated cylindrical morphology (radius = 10 ± 1.5 Å, height = 358 ± 4.7 Å) with fully dissociated and solvated sulfonic acid groups on the particle wall. In conclusion, these results highlight an important discrepancy between the methods of preparing Nafion dispersions and the use of simplified analysis techniques to describe Nafion morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pulsed, Photonuclear-induced, Neutron Measurements of Nuclear Materials with Composite Shielding

Active measurements were performed using a 10-MeV electron accelerator with inspection objects containing various nuclear and nonnuclear materials available at the Idaho National Laboratory’s Zero Power Physics Reactor (ZPPR) facility. The inspection objects were assembled from ZPPR reactor plate materials to evaluate the measurement technologies for the characterization of plutonium, depleted uranium or highly enriched uranium shielded by both nuclear and non-nuclear materials. A series of pulsed photonuclear, time-correlated measurements were performed with unshielded calibration materials and then compared with the more complex composite shield configurations. The measurements used multiple 3He detectors that are designed to detect fission neutrons between pulses of an electron linear accelerator. The accelerator produced 10-MeV bremsstrahlung X-rays at a repetition rate of 125 Hz (8 ms between pulses) with a 4-us pulse width. All inspected objects were positioned on beam centerline and 100 cm from the X-ray source. The time-correlated data was collected in parallel using both a Los Alamos National Laboratory-designed list-mode acquisition system and a commercial multichannel scaler analyzer. A combination of different measurement configurations and data analysis methods enabled the identification of each object. This paper describes the experimental configuration, the ZPPR inspection objects used, and the various measurement and analysis results for each inspected object.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AATTENUATION—The Atmospheric Attenuation Model for CSP Tower Plants: A Look-Up Table for Operational Implementation

Attenuation of solar radiation between the receiver and the heliostat field in concentrated solar power (CSP) tower plants can reduce the overall system performance significantly. The attenuation varies strongly with time and the average attenuation at different sites might also vary strongly from each other. If no site specific attenuation data is available, the optimal plant design cannot be determined and rough estimations of the attenuation effect are required leading to high uncertainties of yield analysis calculations. The attenuation is caused mainly by water vapor content and aerosol particles in the lower atmospheric layer above ground. Although several on-site measurement systems have been developed during recent years, attenuation data sets are usually not available to be included during the plant project development. An Atmospheric Attenuation (AATTENUATION) model to derive the atmospheric transmittance between a heliostat and receiver on the basis of common direct normal irradiance (DNI), temperature, relative humidity, and barometric pressure measurements was developed and validated by the authors earlier. The model allows the accurate estimation of attenuation for sites with low attenuation and gives an estimation of the attenuation for less clear sites. However, the site-dependent coefficients of the AATTENUATION model had to be developed individually for each site of interest, which required time-consuming radiative transfer simulations, considering the exact location and altitude, as well as the pre-dominant aerosol type at the location. This strongly limited the application of the model despite its typically available input data. In this manuscript, a look-up table (LUT) is presented which enables the application of the AATTENUATION model at the site of interest without the necessity to perform the according complex radiative transfer calculations for each site individually. This enables the application of the AATTENUATION model for virtually all resource assessments for tower plants and in an operational mode in real time within plant monitoring systems around the world. The LUT also facilitates the generation of solar attenuation maps on the basis of long-term meteorological data sets which can be considered during resource assessment for CSP tower plant projects. The LUTs are provided together with this manuscript as supplementary files. The LUT for the AATTENUATION model was developed for a solar zenith angle (SZA) grid of 1°, an altitude grid of 100 m, 7 different standard aerosol types and the standard AFGL atmospheres for mid-latitudes and the tropics. The LUT was tested against the original version of the AATTENUATION model at 4 sites in Morocco and Spain, and it was found that the additional uncertainty introduced by the application of the LUT is negligible. With the information of latitude, longitude, altitude above mean sea level, DNI, relative humidity (RH), ambient temperature (Tair), and barometric pressure (bp), the attenuation can be now derived easily for each site of interest.

14 SOLAR ENERGY↗

New Particle Formation and Growth to Climate-Relevant Aerosols at a Background Remote Site in the Western Himalaya

New particle formation (NPF) can influence the Earth’s radiative budget when the newly formed particles grow to climate-relevant sizes. Here, we present analysis of 21-months of continuous aerosol size distribution measurements at a background remote site in the western Himalaya and provide observational evidence that newly formed particles grow to cloud condensation nuclei (CCN)-active sizes (i.e. >20-100 nm in diameter). Out of total 55 NPF events, 38 (66%) events occurred in the pre-monsoon season (March-May). NPF events were classified into those with and without pollution influence as polluted and cleaner, respectively, using black carbon data. The analysis of air mass age, based on the ratio of number concentration of Aitken to accumulation mode aerosols, indicated that NPF occurred in the relatively cleaner air masses reaching to the site. The median formation rate of 10 nm particles and particle growth rates for cleaner events were three-fold and two-fold, respectively, higher than polluted events. We present the first estimates of the survival probability of newly formed particles to 50 nm and 100 nm size, which was not attempted in an Indian environment previously. The survival probability to 50 nm particles ranged from 44 to 98%, with a mean and standard deviation of 82 ± 18%. On average, ~60% of the particles surviving to 50 nm survived to 100 nm, making the overall survival probability of 100 nm to 53 ± 31%. This indicates that the probability of nucleated particles growing to CCN-active sizes under a large source of condensing vapor (transported from nearby lower-altitude regions) and low pre-existing particle concentrations (background mountain site) is high compared to the previous studies. These findings highlight the importance of the efficiency of nucleation events for producing CCN, which is a critical basis of aerosol indirect effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A modelling study of aromatic soot precursors formation in laminar methane and ethene flames

A relatively short kinetic mechanism (93 species and 729 reactions) was developed to predict the formation of poly-aromatic hydrocarbons (PAH) and their growth of up to five aromatic rings in methane and ethane-fueled flames. The model is based on the C{sub 0}-C{sub 2} chemistry with recent well-established chemical kinetic data. Reaction paths for mostly stable and well studied PAH molecules were delineated and the reaction rate constants for PAH growth were collected. These were obtained by analysing the data reported in the literature during the last 30 years, or by using the estimates and optimisations of experimentally measured concentration profiles for small and PAH molecules. These profiles were collected by 12 independent work groups in laminar premixed CH{sub 4} and C{sub 2}H{sub 4} flames under atmospheric pressure or in shock tube experiments under elevated pressure. The simulated flame speeds, temporal profiles of small and large aromatics and also soot particles volume fraction data are in good agreement with the experimental data received for different temperatures, mixing ratios and diluents. The extensive analysis of PAH reaction steps showed that the main reaction routes can be conditionally divided into ''low temperature'' reaction routes, dominating at T < 1550 K, and ''high temperature'' reaction routes, which contribute mostly to PAH formation at T > 1550 K. The presented mechanism can be used as the basis for further extensions or reductions applied in kinetic schemes involving PAH and soot production in practical fuel combustion. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Halo-independent analysis of direct dark matter detection through electron scattering

Sub-GeV mass dark matter particles whose collisions with nuclei would not deposit sufficient energy to be detected, could instead be revealed through their interaction with electrons. Analyses of data from direct detection experiments usually require assuming a local dark matter halo velocity distribution. In the halo-independent analysis method, properties of this distribution are instead inferred from direct dark matter detection data, which allows then to compare different data without making any assumption on the uncertain local dark halo characteristics. Furthermore, this method has so far been developed for and applied to dark matter scattering off nuclei. Here we demonstrate how this analysis can be applied to scattering off electrons.

79 ASTRONOMY AND ASTROPHYSICS↗

Precision measurement of the muon decay parameters {rho} and {delta}

The TWIST Collaboration has performed new measurements of two of the parameters that describe muon decay: {rho}, which governs the shape of the overall momentum spectrum, and {delta}, which governs the momentum dependence of the parity-violating decay asymmetry. This analysis gives the results {rho}=0.750 14{+-}0.000 17(stat){+-}0.000 44(syst){+-}0.000 11({eta}), where the last uncertainty arises from the correlation between {rho} and the decay parameter {eta}, and {delta}=0.750 67{+-}0.000 30(stat){+-}0.000 67(syst). These are consistent with the value of 3/4 given for both parameters in the standard model of particle physics, and are a factor of two more precise than the measurements previously published by TWIST. A new global analysis of all available muon decay data incorporating these results is presented. Improved lower and upper limits on the decay parameter P{sub {mu}}{sup {pi}}{xi} of 0.995 24<P{sub {mu}}{sup {pi}}{xi}{<=}{xi}<1.000 91 at 90% confidence are determined, where P{sub {mu}}{sup {pi}} is the polarization of the muon when it is created during pion decay, and {xi} governs the muon decay asymmetry. These results set new model-independent constraints on the possible weak interactions of right-handed particles. Specific implications for left-right symmetric models are discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗