Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The novel Mechanical Ventilator Milano for the COVID-19 pandemic

This paper presents the Mechanical Ventilator Milano (MVM), a novel intensive therapy mechanical ventilator designed for rapid, large-scale, low-cost production for the COVID-19 pandemic. Free of moving mechanical parts and requiring only a source of compressed oxygen and medical air to operate, the MVM is designed to support the long-term invasive ventilation often required for COVID-19 patients and operates in pressure-regulated ventilation modes, which minimize the risk of furthering lung trauma. The MVM was extensively tested against ISO standards in the laboratory using a breathing simulator, with good agreement between input and measured breathing parameters and performing correctly in response to fault conditions and stability tests. The MVM has obtained Emergency Use Authorization by U.S. Food and Drug Administration (FDA) for use in healthcare settings during the COVID-19 pandemic and Health Canada Medical Device Authorization for Importation or Sale, under Interim Order for Use in Relation to COVID-19. Furthermore, following these certifications, mass production is ongoing and distribution is under way in several countries. The MVM was designed, tested, prepared for certification, and mass produced in the space of a few months by a unique collaboration of respiratory healthcare professionals and experimental physicists, working with industrial partners, and is an excellent ventilator candidate for this pandemic anywhere in the world

60 APPLIED LIFE SCIENCES↗
NASA NTRS1995

Interaction of an interplanetary shock with the heliospheric plasma sheet

Interplanetary shocks often propagate along the heliospheric plasma sheet (HPS) where the interplanetary magnetic field (IMF) changes its polarity. This problem is investigated by the time-dependent 2.5-D MHD numerical model in the meridional plane. An example of computation is shown in the figure using density (log) contours and IMF vectors. Values of plasma parameters along the HPS fluctuate in time due to the Kelvin-Helmholtz instability. The HPS with its decreased intensity of the IMF as well as with its increased mass density causes a dimple in the shock structure (relatively weak for the forward shock, significant for the reverse shock, and very large for the contact discontinuity). Beyond the forward shock, the HPS is slightly compressed due to the post-shock increase of the azimuthal IMF component. Then follows expansion of the HPS surrounded by the highly-deformed contact discontinuity. A significant draping of IMF lines occurs around this structure that increases the meridional component of the IMF. This can cause a favorable condition for initiation of a geomagnetic storm.

Odstrcil, D.↗
NASA NTRS1976

Plastic deformation of polycrystalline zirconium carbide

The compressive yield strength of arc-melted polycrystalline zirconium carbide has been found to vary from 77 kg per sq mm at 1200 C to 19 kg per sq mm at 1800 C. Yield drops were observed with plastic strain-rates greater than 0.003/sec but not with slower strain rates. Strain-rate change experiments yielded values for the strain-rate sensitivity parameter m which range from 6.5 at 1500 C to 3.8 at 1800 C, and the product dislocation velocity stress exponent times T was found to decrease linearly with increasing temperature. The deformation rate results are consistent with the Kelly-Rowcliffe model in which the diffusion of carbon assists the motion of dislocations.

Darolia, R.↗
NASA NTRS1986

Spall velocity measurements from laboratory impact craters

Spall velocities were measured for a series of impacts into San Marcos gabbro. Impact velocities ranged from 1 to 6.5 km/sec. Projectiles varied in material and size with a maximum mass of 4g for a lead bullet to a minimum of 0.04 g for an aluminum sphere. The spall velocities were calculated both from measurements taken from films of the events and from estimates based on range measurements of the spall fragments. The maximum spall velocity observed was 27 m/sec, or 0.5 percent of the impact velocity. The measured spall velocities were within the range predicted by the Melosh (1984) spallation model for the given experimental parameters. The compatability between the Melosh model for large planetary impacts and the results of these small scale experiments is considered in detail. The targets were also bisected to observe the internal fractures. A series of fractures were observed whose location coincided with the boundary of the theoretical near surface zone predicted by Melosh. Above this boundary the target material should receive reduced levels of compressive stress as compared to the more highly shocked region below.

Polanskey, Carol A.↗
NASA NTRS1990

Weight minimization of a support structure

This paper addresses the weight minimization of a circular plate-like structure which resulted in a 26 percent weight reduction. The optimization was performed numerically with the COPES/ADS program using the modified method of feasible directions. Design parameters were the inner thickness and outer thickness of the plate with constraints on maximum yield stress and maximum transverse displacement. Also, constraints were specified for the upper and lower bounds of the fundamental frequency and plate thicknesses. The MSC/NASTRAN finite element program was used for the evaluation of response variables. Original and final designs of the plate were tested using an Instron tension-compression machine to compare finite element results to measured strain data. The difference between finite element strain components and measured strain data was within engineering accuracy.

Kluberdanz, Donald J.↗
NASA NTRS1994

Micromechanics of fatigue in woven and stitched composites

The goals of this research program were to: (1) determine how microstructural factors, especially the architecture of reinforcing fibers, control stiffness, strength, and fatigue life in 3D woven composites; (2) identify mechanisms of failure; (3) model composite stiffness; (4) model notched and unnotched strength; and (5) model fatigue life. We have examined a total of eleven different angle and orthogonal interlock woven composites. Extensive testing has revealed that these 3D woven composites possess an extraordinary combination of strength, damage tolerance, and notch insensitivity in compression and tension and in monotonic and cyclic loading. In many important regards, 3D woven composites far outstrip conventional 2D laminates or stitched laminates. Detailed microscopic analysis of damage has led to a comprehensive picture of the essential mechanisms of failure and how they are related to the reinforcement geometry. The critical characteristics of the weave architecture that promote favorable properties have been identified. Key parameters are tow size and the distributions in space and strength of geometrical flaws. The geometrical flaws should be regarded as controllable characteristics of the weave in design and manufacture. In addressing our goals, the simplest possible models of properties were always sought, in a blend of old and new modeling concepts. Nevertheless, certain properties, especially regarding damage tolerance, ultimate failure, and the detailed effects of weave architecture, require computationally intensive stochastic modeling. We have developed a new model, the 'binary model,' to carry out such tasks in the most efficient manner and with faithful representation of crucial mechanisms. This is the final report for contract NAS1-18840. It covers all work from April 1989 up to the conclusion of the program in January 1993.

Cox, B. N.↗
NASA NTRS1995

Electrolysis Performance Improvement Concept Study (EPICS) flight experiment phase C/D

The overall purpose of the Electrolysis Performance Improvement Concept Study flight experiment is to demonstrate and validate in a microgravity environment the Static Feed Electrolyzer concept as well as investigate the effect of microgravity on water electrolysis performance. The scope of the experiment includes variations in microstructural characteristics of electrodes and current densities in a static feed electrolysis cell configuration. The results of the flight experiment will be used to improve efficiency of the static feed electrolysis process and other electrochemical regenerative life support processes by reducing power and expanding the operational range. Specific technologies that will benefit include water electrolysis for propulsion, energy storage, life support, extravehicular activity, in-space manufacturing and in-space science in addition to other electrochemical regenerative life support technologies such as electrochemical carbon dioxide and oxygen separation, electrochemical oxygen compression and water vapor electrolysis. The Electrolysis Performance Improvement Concept Study flight experiment design incorporates two primary hardware assemblies: the Mechanical/Electrochemical Assembly and the Control/Monitor Instrumentation. The Mechanical/Electrochemical Assembly contains three separate integrated electrolysis cells along with supporting pressure and temperature control components. The Control/Monitor Instrumentation controls the operation of the experiment via the Mechanical/Electrochemical Assembly components and provides for monitoring and control of critical parameters and storage of experimental data.

Schubert, F. H.↗
NASA NTRS1971

Calculation of compressible nonadiabatic boundary layers in laminar, transitional and turbulent flow by the method of integral relations

A computer program was developed to do the calculations for two-dimensional or axisymmetric configurations from low speeds to hypersonic speeds with arbitrary streamwise pressure, temperature, and Mach number distributions. Options are provided for obtaining initial conditions either from experimental information or from a theoretical similarity solution. The transition region can be described either by an arbitrary distribution of intermittency or by a function based on Emmons' probability theory. Correlations were developed for use in estimating the parameters of the theoretical intermittency function. Correlations obtained from other sources are used for estimating the transition point. Comparisons were made between calculated and measured boundary layer quantities for laminar, transitional, and turbulent flows on flat plates, cones, cone flares, and a waisted body of revolution. Excellent agreement was obtained between the present theory and two other theories based on the method of finite differences. The intermittency required to reproduce some experimental heat transfer results in hypersonic flow was found to be quite different from the theoretical function. It is suggested that the simple probability theory of Emmons may not be valid for representing the intermittency of hypersonic transitional boundary layers and that the program could be useful as a tool for detailed study of the intermittency of the transition region.

Kuhn, G. D.↗
DOE OSTI2022

Octane Requirements of Lean Mixed-Mode Combustion in a Direct-Injection Spark-Ignition Engine

Here, this study investigates the octane requirements of a hybrid flame propagation and controlled autoignition mode referred to as mixed-mode combustion (MMC), which allows for strong control over combustion parameters via a spark-initiated deflagration phase. Due to the throughput limitations associated with both experiments and 3-D computational fluid dynamics calculations, a hybrid 0-D and 1-D modeling methodology was developed, supported by experimental validation data. This modeling approach relied on 1-D, two-zone engine simulations to predict bulk in-cylinder thermodynamic conditions over a range of engine speeds, compression ratios, intake pressures, trapped residual levels, fueling rates, and spark timings. Those predictions were then transferred to a 0-D chemical kinetic model, which was used to evaluate the autoignition behavior of fuels when subjected to temperature–pressure trajectories of interest. Finally, the predicted autoignition phasings were screened relative to the progress of the modeled deflagration-based combustion in order to determine if an operating condition was feasible or infeasible due to knock or stability limits. The combined modeling and experimental results reveal that MMC has an octane requirement similar to modern stoichiometric spark-ignition engines in that fuels with high research octane number (RON) and high octane sensitivity (S) enable higher loads. Experimental trends with varying RON and S were well predicted by the model for 1000 and 1400 rpm, confirming its utility in identifying the compatibility of a fuel’s autoignition behavior with an engine configuration and operating strategy. However, the model was not effective in predicting (nor designed to predict) operability limits due to cycle-to-cycle variations, which experimentally inhibited operation of some fuels at 2000 rpm. Putting the operable limits and efficiency from MMC in the context of a state-of-the-art engine, the MMC showed superior efficiencies over the range investigated, demonstrating the potential to further improve fuel economy.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Lattice Dynamics and Structural Phase Transitions in Eu 2 O 3

Using the density functional theory, we study the structural and lattice dynamical properties of europium sesquioxide (Eu 2 O 3 ) in the cubic, trigonal, and monoclinic phases. The obtained lattice parameters and energies of the Raman modes show a good agreement with the available experimental data. The Eu-partial phonon density of states calculated for the cubic structure is compared with the nuclear inelastic scattering data obtained from a 20 nm thick Eu 2 O 3 film deposited on a YSZ substrate. A small shift of the experimental spectrum to higher energies results from a compressive strain induced by the substrate. On the basis of lattice and phonon properties, we analyze the mechanisms of structural transitions between different phases of Eu 2 O 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Dimensionality Reduction with Variational Encoders Based on Subsystem Purification

Efficient methods for encoding and compression are likely to pave the way toward the problem of efficient trainability on higher-dimensional Hilbert spaces, overcoming issues of barren plateaus. Here, we propose an alternative approach to variational autoencoders to reduce the dimensionality of states represented in higher dimensional Hilbert spaces. To this end, we build a variational algorithm-based autoencoder circuit that takes as input a dataset and optimizes the parameters of a Parameterized Quantum Circuit (PQC) ansatz to produce an output state that can be represented as a tensor product of two subsystems by minimizing $Tr(ρ^2)$. The output of this circuit is passed through a series of controlled swap gates and measurements to output a state with half the number of qubits while retaining the features of the starting state in the same spirit as any dimension-reduction technique used in classical algorithms. The output obtained is used for supervised learning to guarantee the working of the encoding procedure thus developed. We make use of the Bars and Stripes (BAS) dataset for an 8 × 8 grid to create efficient encoding states and report a classification accuracy of 95% on the same. Thus, the demonstrated example provides proof for the working of the method in reducing states represented in large Hilbert spaces while maintaining the features required for any further machine learning algorithm that follows.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1972

Dynamics of a supersonic inlet-engine combination subjected to disturbances in fuel flow and inlet overboard bypass airflow

An axisymmetric mixed-compression supersonic inlet and a single-spool turbojet engine were dynamically tested at Mach 2.5. The propulsion system was subjected to sweep-frequency sinusoidal disturbances of either inlet overboard bypass airflow. The disturbances were at a logarithmic sweep rate of 1 decade per minute. Dynamic responses were taken of signals throughout the propulsion system. Selected signals were reduced relative to the prime propulsion system parameters. The experimental data are presented in Bode plots. Most of the plots are for a frequency range of 1.0 to 50 hertz.

Wallhagen, R. E.↗
NASA NTRS1984

Complete flowfields over low and wide angle AOTV conceptual configurations

Flowfields over two conceptual aeroassisted orbital transfer vehicles, a moderate lift-to-drag ratio biconic, and an axisymmetric zero lift aerobrake are investigated. The solution procedures employ a compressible Navier-Stokes time-asymptotic technique for blunt body flow and a Parabolized Navier-Stokes spatial marching technique for the primarily supersonic shock layer flow over low-angle bodies. Emphasis is placed on the laminar convective heating predictions and comparisons to experimental data where available. Code robustness and solution times are discussed and guidelines are given for the specification of various numerical parameters. The Parabolized Navier-Stokes technique has a high probability of solution success for the range of applications considered herein, and very good comparisons with experimental heat-transfer data have been obtained. The blunt body Navier-Stokes code is more sensitive to parameter specification for the aerobrake calculations. Still, coarse grid solutions can be obtained quickly to get a good first cut at flowfield definition. Fair to good comparisons have been obtained between experimental heating and pressure data and coarse and fine grid solutions.

Gnoffo, P. A.↗
NASA NTRS1996

Numerical Simulation of Mixing Enhancement in a Hot Supersonic Jet

Experimental observations show that the presence of small tabs on the edge of a hot, compressible jet exiting into a slower moving, colder ambient flow can increase the rate of spreading of the jet. This suggests that the rate of mixing of the jet and the ambient fluid is also increased. In order to elucidate the physical mechanism responsible for the increased spreading rate a set of calculations were carried out within the framework of the compressible three dimensional Navier-Stokes equations. A series of grid refinements were made to assess the accuracy of the results. The first simulated the flow without the tabs, obtaining reasonable agreement with experimental measurements of the velocity. We then simulated the flow, without tabs, over a range of values of the convective Mach number in order to determine the dependence of the mixing on this parameter. Simulations with modeled tabs were also carried out. In these calculations the effect of the tabs on the flow was modeled by pairs of counter rotating vortices. The results of these calculations indeed show that the presence of the tabs increase the spreading rate of the jet. The basic physical mechanism responsible for the enhanced spreading rate is discussed and qualitative comparisons with flow visualizations are made.

Grosch, C. E.↗
DOE OSTI2025

Influence of gradation on shear behavior and pore water response of sand

Here, this paper examines the influence of particle size distribution (PSD) on the shearing behavior of sand using axisymmetric triaxial compression (ATC) testing in conjunction with 3D imaging using synchrotron micro-computed tomography (SMT). Angular sand was sieved to obtain a narrow gradation (uniform) and a wide gradation (non-uniform) with uniformity coefficients (C u ) of 1.2 and 3.0, respectively. Experiments were conducted under drained conditions and a constant effective cell pressure (σ$^{'}_3$) of 50 kPa at low and high back pressures (BP). Results of paired ATC-SMT were analyzed in terms of global constitutive behavior, strain localization, and localized flow characteristics. A new particle tracking algorithm is developed to expose strain localization. Relative particle translation gradient (RPTG) results revealed that gradation affects how early the shear band develops and a tendency for narrow gradation to exhibit varying degrees of diffused shear band at high axial strain (ε 1 ) even though a clear single shear band was observed at the peak strength. Geometric tortuosity (τ) is used as a quantitative parameter to assess flow changes and the efficiency of the flow path. Representative elementary volumes (REVs) inside and outside the shear band were analyzed and the results showed a variation in flow path characteristics where wide gradation specimens had preferential flow paths.

Computed tomography↗
NASA NTRS1967

Mechanics of Boundary Layer Transition. Part 5: Boundary Layer Stability theory in incompressible and compressible flow

The fundamentals of stability theory, its chief results, and the physical mechanisms at work are presented. The stability theory of the laminar boundary determines whether a small disturbance introduced into the boundary layer will amplify or damp. If the disturbance damps, the boundary layer remains laminar. If the disturbance amplifies, and by a sufficient amount, then transition to turbulence eventually takes place. The stability theory establishes those states of the boundary layer which are most likely to lead to transition, identifys those frequencies which are the most dangerous, and indicates how the external parameters can best be changed to avoid transition.

Mack, L. M.↗
DOE OSTI2020

A generalized power-law criterion for rocks based on Mohr failure theory

Nonlinearity of Mohr envelopes confirmed by past laboratory test data can be of considerable importance in theoretical interpretation of rock strength behaviors and many practical applications. Current nonlinear failure criteria are introduced with parameters to empirically fit test data, and the physical and mechanical meanings of these fitting parameters are often not known. Predicted strengths by theoretical criteria (e.g., Griffith criterion) generally do not agree well with test data. Considering the nonlinear properties of a Mohr envelope, a nonlinear failure criterion in a generalized power-law form is derived in this paper based on strength magnitude coefficient (a) and failure envelope curvature coefficient (n) which are expressed in terms of uniaxial tensile strength, uniaxial compressive strength, and angle of internal friction. Test data on granite, marble, dolomite, and andesite from published literature were chosen to test the performance of the proposed criterion along with Griffith and Hoek-Brown criteria. Statistical analysis was performed to evaluate the application of different criteria in predicting the strength of rocks. In addition, some Griffith-typed criteria are mathematically shown to be the special cases of the proposed criterion. The proposed and Hoek-Brown criteria have similar power-law forms with a significant difference in the coefficient functions that govern the shear strength magnitude of rock. The different tensile and compressive failure mechanisms are also investigated from the perspective of the relationship between the uniaxial tension Mohr circle and the proposed failure envelope.

58 GEOSCIENCES↗