Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oscillating flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Experimental and numerical analysis of the wing rock characteristics of a 'wing-body-tail' configuration

Free-to-roll wind tunnel tests were conducted and a computer simulation exercise was performed in an effort to investigate in detail the mechanism of wing rock on a configuration that consisted of a highly-slender forebody and a 78 deg swept delta wing. In the wind tunnel test, the roll angle and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the wind tunnel test confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly showed the energy balance necessary to sustain the limit cycle oscillation. Pressure measurements on the wing revealed the hysteresis of the wing rock process. First, second and nth order models for the aerodynamic damping were developed and examined with a one degree of freedom computer simulation. Very good agreement with the observed behavior from the wind tunnel was obtained.

Suarez, Carlos J.↗
NASA NTRS2013

Flutter Analysis of the Thermal Protection Layer on the NASA HIAD

A combination of classical plate theory and a supersonic aerodynamic model is used to study the aeroelastic flutter behavior of a proposed thermal protection system (TPS) for the NASA HIAD. The analysis pertains to the rectangular configurations currently being tested in a NASA wind-tunnel facility, and may explain why oscillations of the articles could be observed. An analysis using a linear flat plate model indicated that flutter was possible well within the supersonic flow regime of the wind tunnel tests. A more complex nonlinear analysis of the TPS, taking into account any material curvature present due to the restraint system or substructure, indicated that significantly greater aerodynamic forcing is required for the onset of flutter. Chaotic and periodic limit cycle oscillations (LCOs) of the TPS are possible depending on how the curvature is imposed. When the pressure from the base substructure on the bottom of the TPS is used as the source of curvature, the flutter boundary increases rapidly and chaotic behavior is eliminated.

Goldman, Benjamin D.↗
NASA NTRSDate not supplied

Atmospheric Boundary-Layer and Flutter Computations Using CFD Model of the Transonic Dynamics Tunnel

This paper presents two Computational Fluid Dynamics (CFD) models of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). The TDT is a continuous-flow, closed circuit wind tunnel with a 16- by 16-foot slotted test section with cropped corners. The tunnel was originally built as the 19-ft Pressure Tunnel in 1938, but it was converted to the current transonic tunnel in the 1950s, with capabilities to use either air or heavy gas as the test medium. The first computational model describes the generation of an atmospheric-boundary-layer (ABL) profile inside the tunnel. An ABL, which includes both a wind profile and turbulence content, is one of the aerodynamic characteristics affecting the occurrence of wind-induced oscillations for a launch vehicle sitting on a pad. The challenging part of this analysis was modeling the turbulent flow inside the tunnel. This is due to the special ABL-generating hardware that was installed at the entrance of the TDT test section in order to change the downstream velocity profile and to introduce velocity fluctuations into the flow. The second CFD model builds on the computational aeroelastic results that were generated in support of the second Aeroelastic Prediction Workshop (AePW) for the NASA Benchmark Supercritical Wing (BSCW) configuration. During the AePW, the wing-only configuration (classical free-air model) was analyzed. In the current study, the flutter computations were conducted on the configuration as it was mounted in the TDT during the experiment. This includes the wing attached to the splitter plate that was attached to the wind-tunnel walls. The preliminary results show that the wind-tunnel walls marginally affect flutter prediction.

Pawel Chwalowski↗
NASA NTRS2012

Analysis of Buzz in a Supersonic Inlet

A dual-stream, low-boom supersonic inlet designed for use on a small, Mach 1.6 aircraft was tested experimentally in the 8- by 6-Foot Supersonic Wind Tunnel (SWT) at the NASA Glenn Research Center (GRC). The tests showed that the inlet had good recovery and stable operation over large mass flow range. The inlet went into buzz at mass flows well below that needed for engine operation, and the experiments generated a wealth of data during buzz. High frequency response pressure measurements and high-speed schlieren videos were recorded for many buzz events. The objective of the present work was to use computational fluid dynamics (CFD) to predict some of the experimental data taken during buzz, compare those predictions to the experimental data, and to use both datasets to explain the physics of the buzz cycle. The calculations were done with the Wind-US CFD code using a second-order time-accurate differencing scheme and the SST turbulence model. Computed Mach number contours were compared with schlieren images, and ensemble-averaged unsteady pressures were compared to data. The results showed that the buzz cycle consisted partly of spike buzz, an unsteady oscillation of the main shock at the spike tip while the inlet pressure dropped, and partly of choked flow while the inlet repressurized. Most of the results could be explained by theory proposed by Dailey in 1954, but did not support commonly used acoustic resonance explanations.

Chima, Rodrick V.↗
NASA NTRS2017

The Stochastic X-Ray Variability of the Accreting Millisecond Pulsar MAXI J0911-655

In this work, I report on the stochastic X-ray variability of the 340 hertz accreting millisecond pulsar MAXI J0911-655. Analyzing pointed observations of the XMM-Newton and NuSTAR observatories, I find that the source shows broad band-limited stochastic variability in the 0.01-10 hertz range with a total fractional variability of approximately 24 percent root mean square timing residuals in the 0.4 to 3 kiloelectronvolt energy band that increases to approximately 40 percent root mean square timing residuals in the 3 to 10 kiloelectronvolt band. Additionally, a pair of harmonically related quasi-periodic oscillations (QPOs) are discovered. The fundamental frequency of this harmonic pair is observed between frequencies of 62 and 146 megahertz. Like the band-limited noise, the amplitudes of the QPOs show a steep increase as a function of energy; this suggests that they share a similar origin, likely the inner accretion flow. Based on their energy dependence and frequency relation with respect to the noise terms, the QPOs are identified as low-frequency oscillations and discussed in terms of the Lense-Thirring precession model.

ulsars: general { stars: neutron { X-rays: binarie↗
NASA NTRS2019

The Effect of a Hall Thruster-Like Magnetic Field on Operation of a 25-A Class Hollow Cathode

The effect of applying a Hall thruster-like magnetic field to a 25-A class hollow cathode is experimentally characterized. A magnetic simulator that approximated the magnetic field of NASA's HERMeS Hall thruster was used to apply magnetic fields of strengths that varied from 0 to 1.25 of the nominal HERMeS value Bnom. Cathode operation was characterized by parameters such as the discharge voltage, voltage and current oscillation magnitudes, and ion energy spectra. It was found that the application of the magnetic field profoundly affected the operation of the cathode. For the nominal xenon flow rate of 14.7 sccm, when increasing the magnetic field from 0 Bnom to 1.25 Bnom, the discharge voltage increased from 20 V to 40 V and the cathode orifice plate temperature increased from 934 ºC to 987 ºC. Oscillations of the discharge voltage, discharge current, and keeper voltage all remained relatively quiescent. However, the ion energy spectra changed profoundly between conditions, with little ion population above 50 V at 0 Bnom, yet a high-energy ion tail extending above 150 V at the 1.25 Bnom case. These high-energy ions appeared without an increase in the oscillation levels, indicating that previous cathode mode definitions may not apply with the Hall thruster-like magnetic field. The implications of these results on existing cathode operational mode definitions, component-level cathode testing, and operation in a Hall thruster are discussed.

Hall, Scott J.↗
NASA NTRS1977

Nonlinear, unsteady aerodynamic loads on rectangular and delta wings

Nonlinear unsteady aerodynamic loads on rectangular and delta wings in an incompressible flow are calculated by using an unsteady vortex-lattice model. Examples include flows past fixed wings in unsteady uniform streams and flows past wings undergoing unsteady motions. The unsteadiness may be due to gusty winds or pitching oscillations. The present technique establishes a reliable approach which can be utilized in the analysis of problems associated with the dynamics and aeroelasticity of wings within a wide range of angles of attack.

Atta, E. H.↗
NASA NTRS1988

Unsteady solution of incompressible Navier-Stokes equations

The numerical scheme used by the present time-accurate FEM numerical method for incompressible Navier-Stokes equations, using primitive variables as the unknowns, is a Crank-Nicholson implicit treatment of all equation terms with central differencing for space derivatives. The introduction of a continuous auxilliary system in pseudo-time, with artificial compressibility, yields the incompressible solution at the advanced time level; time-accurate solutions are thereby obtained for two-dimensional fluid flows in a square cavity, in the cases of both an impulsively starting lid and an oscillating lid.

Soh, W. Y.↗
NASA NTRS1989

The effect of a row of Helmholtz resonators on the turbulence of a boundary layer

Laser velocimetry and hot-film data are presented from an experimental investigation in which a tightly-packed row of Helmholtz resonators was used to introduce a momentum oscillation into a turbulent boundary layer. This device has been proposed as a basis for flow-turbulence control. The resonators are found to suck in high-momentum fluid and expel low or zero-momentum fluid into the flow. The interaction of the resonators produces a local increase in the boundary layer momentum thickness which corresponds to a drag coefficient of the order of 0.01.

Flynn, Kevin P.↗
NASA NTRS1990

Self-induced roll oscillations of low-aspect-ratio rectangular wings

Experimental investigation of small aspect ratio rectangular wings mounted on a free-to-roll sting balance indicated that self-induced roll oscillations are possible when the aspect ratio of such wings is less than 0.5. The oscillations are probably driven by the periodic changes in the location and strength of the side edge vortices, as it has been shown for the 'wing rock' motion of delta wings, where similar changes in the leading edge vortex strength and position cause the roll oscillations. During the roll oscillation cycle the roll angle, normal force, and the side force were recorded and presented for three wings with aspect ratios of 0.25, 0.35, and 0.47. This data indicates that the lift loss during roll oscillations of rectangular wings is less than what was measured for similar delta wings. Also, the flow field of such slender rectangular wings at high angles of attack is more complicated due to the additional leading edge vortex, when compared with the flow field over slender delta wings.

Levin, Daniel↗
NASA NTRS1992

Oscillating-Coolant Heat Exchanger

Devices useful in situations in which heat pipes inadequate. Conceptual oscillating-coolant heat exchanger (OCHEX) transports heat from its hotter portions to cooler portions. Heat transported by oscillation of single-phase fluid, called primary coolant, in coolant passages. No time-averaged flow in tubes, so either heat removed from end reservoirs on every cycle or heat removed indirectly by cooling sides of channels with another coolant. Devices include leading-edge cooling devices in hypersonic aircraft and "frost-free" heat exchangers. Also used in any situation in which heat pipe used and in other situations in which heat pipes not usable.

Scotti, Stephen J.↗
NASA NTRS1992

Unsteady airfoil flow solutions on moving zonal grids

Euler and Navier-Stokes solutions for airfoil flows on zonal grids are presented. The governing equations are solved with an implicit, iterative, factorized numerical scheme. The inviscid fluxes are examined with a third-order accurate upwind method. Zonal grid solutions are compared with experimental measurements for flows over airfoils at fixed angles of incidence. The computed unsteady solutions for rapidly pitching and oscillating airfoils are in good agreement with experiments.

Cricelli, Antonio S.↗
NASA NTRS1992

Convection of tin in a Bridgman system. I - Flow characterization by effective diffusivity measurements

An electrochemical titration method was used to investigate the dynamic states in a cylindrical layer of convecting tin. The liquid tin was contained in a cell, with curved boundaries made of quartz and flat boundaries made of a solid state electrolyte - yttria-stabilized zirconia (YSZ). The electrolyte acted as a window through which a trace amount of oxygen could be pumped in or out by the application of a constant voltage. The concentration at the YSZ interface was monitored by operating the electrochemical cell in the galvanic mode. Experimentally determined effective diffusivities of oxygen were compared with the molecular diffusivity. Dynamic states in the convective flow were thus inferred. Temperature measurements were simultaneously made in order to identify the onset of oscillations from a steady convective regime. The experiments were conducted for two different aspect ratios for various imposed temperature gradients and two different orientations with respect to gravity. Transcritical states were identified and comparison to two-dimensional numerical models were made.

Sears, B.↗
NASA NTRS1993

Transition effects on compressible dynamic stall of transiently pitching airfoils

Experimental results and analysis of the effects of boundary layer tripping on dynamic stall of a transiently pitching airfoil are presented. At low Mach numbers, the tripped airfoil exhibits qualitative similarity with the behavior of the untripped airfoil. However, the local supersonic flow at Mach numbers greater than 0.3 is significantly modified by the trip leading to vastly different shock/boundary layer interactions, dynamic stall onset and vortex formation angles. The formation of the laminar separation bubble is found to have a favorable influence in delaying dynamic stall on the untripped airfoil flow. In both Mach number regimes, the tripped flow actually stalls at slightly lower angles of attack. Further experimentation with three trips on an oscillating airfoil showed that the dynamic stall process is very sensitive to the state of the turbulence in the boundary layer. This sensitivity points to a need for finer turbulence modeling techniques for use in dynamic stall computations.

Wilder, M. C.↗
NASA NTRS1996

Shear Stabilization of a Solidifying Front

The manufacturing of multi-component single crystals with uniform material properties is frequently hampered by the presence of morphological instabilities during the solidification. We discuss the influence of shear flows on the linear and nonlinear stability of the solid/liquid interface during the directional solidification of binary alloys. The flows are generated by nonplanar harmonic translations of the crystal parallel to the mean interface position. Oscillations with physically realizable amplitudes and frequencies are found useful for stabilization purposes.

Davis, Stephen H.↗
NASA NTRS2005

Adaptive Numerical Dissipation Control in High Order Schemes for Multi-D Non-Ideal MHD

The required type and amount of numerical dissipation/filter to accurately resolve all relevant multiscales of complex MHD unsteady high-speed shock/shear/turbulence/combustion problems are not only physical problem dependent, but also vary from one flow region to another. In addition, proper and efficient control of the divergence of the magnetic field (Div(B)) numerical error for high order shock-capturing methods poses extra requirements for the considered type of CPU intensive computations. The goal is to extend our adaptive numerical dissipation control in high order filter schemes and our new divergence-free methods for ideal MHD to non-ideal MHD that include viscosity and resistivity. The key idea consists of automatic detection of different flow features as distinct sensors to signal the appropriate type and amount of numerical dissipation/filter where needed and leave the rest of the region free from numerical dissipation contamination. These scheme-independent detectors are capable of distinguishing shocks/shears, flame sheets, turbulent fluctuations and spurious high-frequency oscillations. The detection algorithm is based on an artificial compression method (ACM) (for shocks/shears), and redundant multiresolution wavelets (WAV) (for the above types of flow feature). These filters also provide a natural and efficient way for the minimization of Div(B) numerical error.

Yee, H. C.↗
NASA NTRS2016

California Reservoir Inflow Projections Using a Hybrid EMD-Matalas Method

Inflow projections provide scenarios for future water availability and are integral to operational reservoir management. They can aid water practitioners in decision-making for conservation efforts, multiyear storage retention, managing flood risk, downstream water releases, and regional growth planning. However, conventional methods are often limited in terms of their ability to incorporate non-stationarity, long run persistence, and the cross-correlation of multiple series in a region. This research aims to address these issues with a hybrid approach that integrates Empirical Mode Decomposition (EMD) with the Matalas multisite generation method. Multiple long-run inflows were examined for the Shasta/Trinity Reservoirs and Oroville Reservoir of California. EMD is used to decompose each inflow series into a set of independent intrinsic mode functions (IMFs) that have different timescales and frequencies. These IMFs were grouped into intradecadal (less-than- 10-year average periodicity) and interdecadal (greater-than-10-year average periodicity) series for each site. The IMF projections at each site were then combined to produce replicates of the historical data. This preserves the correlation structure of the intra- and interdecadal components of the series. The hybrid EMD-Matalas method was compared to a traditional autoregressive lag-one model. Both methods were found to retain the statistical characteristics of the historical data. However, the EMD-Matalas method retained the multiyear wet and dry periods to a greater degree. This was examined by comparing the 5-year and 10-year sums from the traditional model with the hybrid EMD-Matalas model. An advantage of the EMD-Matalas method is the ability to explicitly incorporate modes of non-stationary long-run persistence often associated with large-scale climate drivers such as the El Nino Southern Oscillation (ENSO) or the Pacific Decadal Oscillation (PDO). This contributes to scenario planning that may be particularly important for managing multiyear low flow periods.

inflow projections↗