Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mechanical properties testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of helium on irradiation response of reduced-activation ferritic-martensitic steels: Using nickel isotopes to simulate fusion neutron response

Understanding the effects of helium on microstructures and mechanical properties of reduced-activation ferritic-martensitic steels is important to use of these steels in fusion reactor structures. The 9Cr-2WVTa steels were doped with 58Ni and 60Ni isotopes at 2 weight percent to control the rate of transmutation helium generation. The samples were irradiated in the High Flux Isotope Reactor to ~24 displacements per atom at nominal temperatures of 300, 400, and 500°C, producing 228 and 7 atomic parts-per-million helium in the 58 Ni- and 60 Ni-doped samples, respectively. Transmission electron microscopy revealed a variety of precipitates and the radiation-induced dislocation loops and cavities (voids or helium bubbles). Tensile tests of the irradiated samples at the irradiation temperatures showed radiation-induced hardening at 300°C and radiation-induced softening at 400°C. Analysis indicates that the hardening primarily originated from the loops and cavities. The 58 Ni-doped samples had greater strengthening contributions from loops and cavities, leading to higher hardening with lower ductility than the 60 Ni-doped samples. The greater helium production of 58 Ni did not show pronounced reductions in ductility of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simulations of Multi-Mode Combustion Regimes Realizable In a Gasoline Direct Injection Engine

Lean and dilute gasoline compression ignition (GCI) operation in spark ignition (SI) engines are an attractive strategy to attain high fuel efficiency and low NOx levels. However, this combustion mode is often limited to low-load engine conditions due to the challenges associated with autoignition controllability. In order to overcome this constrain, multi-mode (MM) operating strategies, consisting of advanced compression ignition (ACI) at low load and conventional SI at high load, have been proposed. In this three-dimensional computational fluid dynamics study, the concept of multi-mode combustion using two RON98 gasoline fuel blends (Co-Optima Alkylate and E30) in a gasoline direct injection (GDI) engine were explored. To this end, a new reduced mechanism for simulating the kinetics of E30 fuel blend is introduced in this study. To cover the varying engine load demands for multi-mode engines, primary combustion dynamics observed in ACI and SI combustion modes was characterized and validated against experimental measurements. In order to implement part-load conditions, a strategy of mode transition between SI and ACI combustion (i.e., mixed-mode combustion) was then explored numerically by creating a virtual test condition. The results obtained from the mixed-mode simulations highlight an important feature that deflagrative flame propagation regime coexists with ignition-assisted end-gas autoignition. This study also identifies a role of turbulent flow property adjacent to premixed flame front in characterizing the mixed-mode combustion. The employed hybrid combustion model was verified to perform simulations aiming at suitable range of multi-mode engine operations.

Kim, Sayop↗
DOE OSTI2020

Improving Predictability of Mixed-Phase Clouds and Aerosol Interactions in the Community Earth System Model (CESM) with ARM Measurements

The objective of this project is to improve the simulation and predictability of mixed-phase clouds and aerosol interactions in the Community Earth System Model (CESM) through comparisons with the DOE ARM observations. There are four major goals of the proposed study: (1) Improve the representation of ice microphysical processes in mixed-phase clouds; (2) Develop a long-term multi-sensor mixed-phase cloud dataset; (3) Test the performance of improved ice microphysics in CESM-CAM5 with the ARM data; and (4) Examine mixed-phase cloud microphysics-aerosol-dynamics-radiation interactions in CESM-CAM5. In this project, we have (1) Improved the representation of ice microphysical processes in mixed-phase clouds that include ice nucleation, ice depositional growth through the Wegener–Bergeron–Findeisen (WBF) process, feedbacks between cloud microphysics, dynamics and radiation, and provides links to aerosol properties in the Community Earth System Model (CESM)-Community Atmosphere Model version 5 (CAM5); (2) Developed a long-term multi-sensor mixed-phase cloud dataset. The mixed-phase cloud retrieval algorithms are improved by refining the phase determinations and ice number concentration retrievals. A multi-year mixed-phase cloud observation dataset (1999-2004; October 2013-February 2017) is regenerated at the ARM Barrow site with the improved algorithms. The dataset has been used in the global model evaluation to improve the model parameterizations; (3) Tested the performance of improved ice microphysics in CESM-CAM5 with the ARM data. CESM-CAM5 is run in the DOE Cloud-Associated Parameterizations Testbed (CAPT) and in the single-column model (SCM) mode to facilitate comparison with ARM observations. Multi-year CAPT simulations of seasonal variations of cloud microphysical properties, cloud liquid water path (LWP) and ice water path (IWP), cloud longwave and shortwave forcings, cloud occurrence frequency are evaluated against the ARM multi-sensor mixed-phase cloud retrievals; and (4) Examined mixed-phase cloud microphysics-aerosol-dynamics-radiation interactions in CESM-CAM5 that include the impacts of different ice nucleation mechanisms, sensitivity to dust IN concentration, treatment of the WBF process on mixed-phase cloud properties. Aerosol effect on mixed-phase clouds through the liquid phase (droplet activation) and ice phase processes (e.g., the glaciation indirect effect) is investigated.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Analyzing the Validity of Brazilian Testing Using Digital Image Correlation and Numerical Simulation Techniques

Characterizing the mechanical behavior of rocks plays a crucial role to optimize the fracturing process in unconventional reservoirs. However, due to the intrinsic anisotropy and heterogeneity in unconventional resources, fracture process prediction remains the most significant challenge for sustainable and economic hydrocarbon production. During the deformation tracking under compression, deploying conventional methods (strain gauge, extensometer, etc.) is insufficient to measure the deformation since the physical attachment of the device is restricted to the size of the sample, monitoring limited point-wise deformation, producing difficulties in data retrieval, and a tendency to lose track in failure points, etc. Where conventional methods are limited, the application of digital image correlation (DIC) provides detailed and additional information of strain evolution and fracture patterns under loading. DIC is an image-based optical method that records an object with a camera and monitors the random contrast speckle pattern painted on the facing surface of the specimen. To overcome the existing limitations, this paper presents numerical modeling of Brazilian disc tests under quasi-static conditions to understand the full-field deformation behaviors and finally, it is validated by DIC. As the direct tensile test has limitations in sample preparation and test execution, the Brazilian testing principle is commonly used to evaluate indirectly the tensile strength of rocks. The two-dimensional numerical model was built to predict the stress distribution and full-field deformation on Brazilian disc under compression based on the assumptions of a homogenous, isotropic and linear elastic material. The uniaxial compression test was conducted using the DIC technique to determine the elastic properties of Spider Berea sandstone, which were used as inputs for the simulation model. The model was verified by the analytical solution and compared with the digital image correlation. The numerical simulation results showed that the solutions matched reasonably with the analytical solutions where the maximum deviation of stress distribution was obtained as 14.59%. The strain evolution (normal and shear strains) and displacements along the central horizontal and vertical planes were investigated in three distinguishable percentages of peak loads (20%, 40%, and 90%) to understand the deformation behaviors in rock. The simulation results demonstrated that the strain evolution contours consistently matched with DIC generated contours with a reasonable agreement. The changes in displacement along the central horizontal and vertical planes showed that numerical simulation and DIC generated experimental results were repeatable and matched closely. In terms of validation, Brazilian testing to measure the indirect tensile strength of rocks is still an issue of debate. The numerical model of fracture propagation supported by digital image correlation from this study can be used to explain the fracturing process in the homogeneous material and can be extended to non-homogeneous cases by incorporating heterogeneity, which is essential for rock mechanics field applications.

58 GEOSCIENCES↗
DOE OSTI2022

Prediction of the energetic particle redistribution by an improved critical gradient model and analysis of the transport threshold

Based on the theory of critical gradient model (CGM) and following the simulation method proposed by Waltz et al., a combination of TGLFEP and EPtran code is employed to predict the energetic particle (EP) transport induced by Alfvén eigenmodes (AEs). To be consistent with the experiment, recent improvements to the simulation method include consideration of threshold evolution and orbit loss due to finite orbit width. The revised CGM is applied to simulate two DIII-D experimental discharges (#142111 and #153071). It well reproduces the experimental profiles with multiple unstable AEs and large-scale EP transport. Discharge #142111 had previously been simulated using a nonlinear MHD-kinetic code MEGA with a transport mechanism based on stochasticity induced by overlapping AE. By comparing the simulated EP profiles, we find that the AE transport threshold is approximated by both the MEGA nonlinear stability threshold and the proposed CGM threshold (error <5% for single n and <17% for multiple n simulation). Both of them are larger than the linear stability threshold of the most unstable AE mode by a quantity of the order of the flux needed to sustain EP transport by the background turbulence. Additionally, we have also applied the improved CGM to simulate the α particle redistribution for a China Fusion Engineering Test Reactor steady state scenario. Because of the clear separation between the AE unstable region and the loss cone, only a moderate α particle loss of ~9.6% is predicted.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Potential Formation Damage: An Integrated Reservoir Characterization Study of the Naturally Fractured Carbonate Middle Duperow Formation at the Kevin Dome, Montana

In this study, we integrate geologic and engineering data of a naturally fractured carbonate reservoir at the Kevin Dome, Montana. Well test data are correlated with core description, geochemical and lithology study to determine the flow behavior and communication within the injection test interval and to the surrounding area. Based on a dual-continuum geologic model, numerical brine injection simulations are carried out to validate the interpretation results from our well test analytical models and forecast the probability of CO 2 injection success using current reservoir properties. As a result, our well test analytical models as well as lithology/core description suggest that fluid flow may be mainly restricted to the injection interval and the assumption of radial (horizontal) flow may be appropriate. The well test models also indicate that there is potentially formation damage with a positive skin factor although prior to brine injection well tests, well stimulation through acid treatment was performed. Our numerical simulation results appear to confirm this formation damage by showing additional pressure buildup in the injection data during later test periods. To explain this, acid may have dissolved dolomite then dolomite or calcite may have been formed again further into the matrix/fracture system. Another possible explanation is mechanical clogging of the fractures due to acid dissolving dolomite and dislodging fine grains. Our work also predicts that if no additional well stimulation is performed, the project will have a lower probability of successfully injecting 1 million tons of CO 2 into the Middle Duperow formation over 4 years.

42 ENGINEERING↗
DOE OSTI2021

Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment

Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical Characterization of Stacked Single-Crystal of Polyethylene and Monolayer MoSe 2

Polymer single crystal (SC) is a key building block of semicrystalline polymers. However, direct experimental measurement of freestanding mono-lamella polymer SC has not been demonstrated. This is, in large part, due to the difficulties associated with manipulating freestanding individual mono-lamella SC because of its extremely low rigidity and low robustness. Here, we demonstrate a new strategy to successfully suspend and test a polymer SC by using a 2D material as backing. In particular, mono-lamella polyethylene (PE) SC is stacked on monolayer MoSe 2 , and the hybrid stacks can be suspended over microholes. Nanoindentation is used to probe the suspended PE-SC/MoSe2 stacks and MoSe 2 monolayers. The results suggest the first experimentally-measured in-plane moduli of PE-SC and 2D MoSe 2 as 32 ± 3 and 237 ± 15 GPa, respectively. Such a stacked unit represents an ultrathin structure of polymer-ceramic laminate and the idea can be applied to other laminated composite systems. Therefore, this research will pave the way to accurately measure the mechanical properties of polymer SCs and their composites, as well as provide a key insight on designing composite structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Micropillar Compression of Additively Manufactured 316L Stainless Steels after 2 MeV Proton Irradiation: A Comparison Study between Planar and Cross-Sectional Micropillars

A micropillar compression study with two different techniques was performed on proton-irradiated additively manufactured (AM) 316L stainless steels. The sample was irradiated at 360 °C using 2 MeV protons to 1.8 average displacement per atom (dpa) in the near-surface region. A comparison study with mechanical test and microstructure characterization was made between planar and cross-sectional pillars prepared from the irradiated surface. While a 2 MeV proton irradiation creates a relatively flat damage zone up to 12 µm, the dpa gradient by a factor of 2 leads to significant dpa uncertainty along the pillar height direction for the conventional planar technique. Cross-sectional pillars can significantly reduce such dpa uncertainty. From one single sample, three cross-sectional pillars were able to show dpa-dependent hardening. Furthermore, post-compression transmission electron microscopy allows the determination of the deformation mechanism of individual micropillars. Cross-sectional micropillar compression can be used to study radiation-induced mechanical property changes with better resolution and less data fluctuation.

transmission electron microscopy↗
DOE OSTI2024

Prediction of Dielectric Constant in Series of Polymers by Quantitative Structure-Property Relationship (QSPR)

This work is devoted to the investigation of dielectric permittivity which is influenced by electronic, ionic, and dipolar polarization mechanisms, contributing to the material’s capacity to store electrical energy. In this study, an extended dataset of 86 polymers was analyzed, and two quantitative structure–property relationship (QSPR) models were developed to predict dielectric permittivity. From an initial set of 1273 descriptors, the most relevant ones were selected using a genetic algorithm, and machine learning models were built using the Gradient Boosting Regressor (GBR). In contrast to Multiple Linear Regression (MLR)- and Partial Least Squares (PLS)-based models, the gradient boosting models excel in handling nonlinear relationships and multicollinearity, iteratively optimizing decision trees to improve accuracy without overfitting. The developed GBR models showed high R2 coefficients of 0.938 and 0.822, for the training and test sets, respectively. An Accumulated Local Effect (ALE) technique was applied to assess the relationship between the selected descriptors—eight for the GB_A model and six for the GB_B model, and their impact on target property. ALE analysis revealed that descriptors such as TDB09m had a strong positive effect on permittivity, while MLOGP2 showed a negative effect. These results highlight the effectiveness of the GBR approach in predicting the dielectric properties of polymers, offering improved accuracy and interpretability.

Ascencio-Medina, Estefania↗
DOE OSTI2023

Corrosion property of Alloy 625 in Molten FLiNaK salt according to the Tellurium Concentrations

For this work, the corrosion properties of Alloy 625 have been studied in molten FLiNaK salt for 48 h at 700 °C as a function of tellurium (Te) concentrations using immersion tests and electrochemical methods. Under specific Te concentrations, we found that Te-induced corrosion can be suppressed and help protect the alloy against corrosion. The sample after the immersion test containing 0.1 wt.% Te (0.1 wt.% Te sample) had the lowest corrosion depth and mass loss, coupled with the highest charge transfer resistance, obtained using electrochemical impedance spectroscopy (EIS). On the other hand, the alloy with Te content above 0.1 wt.% exhibited severe corrosion penetration and lower charge transfer resistance in FLiNaK. Based on thermodynamical and electrochemical analyses, a corrosion mechanism of Alloy 625 in the molten salt containing Te was theorized involving the formation of stable corrosion products such as Ni/Fe rich layer depleted in Cr, nickel telluride, and chromium oxide.

Hong, Minsung↗
DOE OSTI2022

Atomistic measurement and modeling of intrinsic fracture toughness of two-dimensional materials

Quantifying the intrinsic mechanical properties of two-dimensional (2D) materials is essential to predict the long-term reliability of materials and systems in emerging applications ranging from energy to health to next-generation sensors and electronics. Currently, measurements of fracture toughness and identification of associated atomistic mechanisms remain challenging. Herein, we report an integrated experimental–computational framework in which in-situ high-resolution transmission electron microscopy (HRTEM) measurements of the intrinsic fracture energy of monolayer MoS 2 and MoSe 2 are in good agreement with atomistic model predictions based on an accurately parameterized interatomic potential. Changes in crystalline structures at the crack tip and crack edges, as observed in in-situ HRTEM crack extension tests, are properly predicted. Such a good agreement is the result of including large deformation pathways and phase transitions in the parameterization of the inter-atomic potential. The established framework emerges as a robust approach to determine the predictive capabilities of molecular dynamics models employed in the screening of 2D materials, in the spirit of the materials genome initiative. Moreover, it enables device-level predictions with superior accuracy (e.g., fatigue lifetime predictions of electro- and opto-electronic nanodevices).

Zhang, Xu↗
DOE OSTI2025

Nonexcitonic mechanism for electronic and structural phase transitions in Ta 2 ⁢Ni⁢(Se,S) 5

Here, we present a first-principles study based on density functional theory (DFT) on the electronic and structural properties of Ta 2 NiSe 5 , a layered transition metal chalcogenide that has been considered as a possible candidate for an excitonic insulator. Our systematic DFT results however provide a nonexcitonic mechanism for the experimentally observed electronic and structural phase transitions in Ta 2 NiSe 5 , in particular explaining why sulfur substitution of selenium reduces the distortion angle in the low-temperature phase and potassium dosing closes the gap in the electronic structure. Moreover, the calculations show that these two effects couple to each other. Further, our first-principles calculations predict several changes in both the crystal structure and electronic structure under the effects of uniform charge dosing and uniaxial strain, which could be tested experimentally.

Tang, Weichen [University of California, Berkeley,↗
DOE OSTI2020

Fracture Strength Determination Methods for Ceramic Materials Applied to Uranium Dioxide

The Advanced Fuels Campaign is currently focusing on development of accident-tolerant fuels that possess a range of property modifications intended to improve fuel performance during accident and transient conditions as well as extend license limits to burnups beyond 62 MWd/kgU. Both of these drivers have identified understanding and mitigating fuel cracking as a key performance criterion. Small-scale cantilever beam testing has been identified as a plausible method by which to collect fracture data for UO 2 as a function of chemical and structural evolutions introduced either during fabrication or irradiation. While this method has been found to be capable of providing data that are in reasonable agreement with literature for unirradiated UO 2 , the inherently small sample volumes that can be sampled limit its ability to capture the statistical nature of mechanisms that govern the fracture of brittle ceramics. A biaxial flexure strength test was developed to be used for unirradiated UO 2 . This method is standard in the community, but no systems presently in use at national laboratories, universities, or private companies are available to be used for nuclear fuel materials. This report describes the operation and benchmarking of this system, which has been validated for a number of common oxides. Future work will extend this system to characterization of both doped UO 2 and other relevant microstructural modifications that can also be measured using small-scale cantilever beam testing. Comparison of datasets collected using both methods will allow the overall applicability of small-scale techniques to be assessed and provide confidence or bounds on their use for irradiated fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Perspective on “code qualifying” new graphite grades for use in advanced nuclear reactors*

The American Society of Mechanical Engineers (ASME) publishes the Boiler and Pressure Vessel (BPV) Code, which include guidance for the safe development, construction, and operation of boilers and pressure vessels. ASME BPV Code Section III “Rules for Construction of Nuclear Facility Components” Division 5 focuses on “High Temperature Reactors”. Subsection HH, subpart A lists the different materials properties that are to be measured and how those properties change due to different environmental conditions (oxidation and irradiation damage) for a graphite to be accepted for use in a high temperature reactor core (i.e., “Code Qualified”). Currently there are no nuclear graphite grades that are “Code Qualified” (i.e., a reactor designer can select a graphite grade and build their reactor without any additional testing), which is due in part to development of new graphite grades in the last 20 years and the lack of comprehensive programs needed to produce the data for the code cases. This perspective is going to discuss the requirements, as called out in the ASME BPV Code, that are necessary to “code qualify” a nuclear graphite grade but will primarily focus on the practical and technical challenges associated with irradiation-induced property changes and how to address these to assist with getting graphite ready for use in advanced nuclear reactors. These same technical challenges can be expected to arise for other materials being developed for advanced reactor concepts.

advanced nuclear reactors↗
DOE OSTI2022

Dynamic aspects of graphene deformation and fracture from approximate density functional theory

Graphene is one of the most intriguing two-dimensional carbon materials. Its mechanical strength and failure are key concerns for materials engineering and applications. Despite the success of fracture mechanics, the mechanism of how pristine materials fail remains an elusive problem. While many theoretical studies based on molecular dynamics using empirical forcefields have tried to address this question, atomic-scale mechanics are not clearly understood. Especially, a widely employed bond-breaking approach based on the critical bond length has not been rigorously tested. Here, utilizing molecular dynamics simulations with density functional based tight binding, we investigate how the failure of the pristine material initiates. The Wiberg bond order (W BO ) to estimate the change of chemical bonds shows a transition from sp 2 (W BO ~ 1.33) to sp 3 (WBO < 1.0) during the deformation. However, it reveals that a single threshold value for either the WBO or bond length is insufficient to decide failure of pristine material without free edges or defects. Instead, collective behaviors of the local atomic group govern the fracture initiation of pristine graphene. Overall, our study provides dynamic mechanical responses based on quantum mechanics, which have not been captured by empirical forcefields, opening opportunities to design properties by precisely coupling the mechanics and quantum mechanics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microstructure and mechanical properties of ultrasonic spot welding of AA7075-T6 and A380 casting aluminum alloy

Ultrasonic spot welding (USW) was employed to join AA7075-T6 and casting Al alloy A380. Under a constant welding power, the influence of the welding time duration (from 1 s to 3 s) on peak temperature, microstructure, hardness, and mechanical strength of the joints were studied. It was found that the peak temperature increased with welding time. A sound solid-state metallurgical bonding was obtained at the joint interface. The cracks occurred at the edge of the joints were eventually eliminated as the welding time increased. A layer of refined grains formed in A380 adjacent to the bonding line. Further, hardness reduction occurred in AA7075 at the joint interface and the degree of hardness reduction and the volume increased with the peak temperature. By increasing welding time, lap shear tensile tests show that the peak load increased from 5.3 kN to 6.55 kN. The corresponding interfacial shear strength ranged from 96.29 MPa to 99.72 MPa, lower than the shear strength of both base materials (331 MPa for AA7075 and 185 MPa for A380). All joint samples exhibited interfacial fracture after lap shear tensile testing, with a thin layer of A380 remnant attached to AA7075 at the center of the fractured surface.

36 MATERIALS SCIENCE↗