Results for “imaging detectors” — Page 64

NASA NTRS2006

Optimization of Single-Sided Charge-Sharing Strip Detectors

Simulation of the charge sharing properties of single-sided CZT strip detectors with small anode pads are presented. The effect of initial event size, carrier repulsion, diffusion, drift, trapping and detrapping are considered. These simulations indicate that such a detector with a 150 m pitch will provide good charge sharing between neighboring pads. This is supported by a comparison of simulations and measurements for a similar detector with a coarser pitch of 225 m that could not provide sufficient sharing. The performance of such a detector used as a gamma-ray imager is discussed.

Hamel, L.A.↗

NASA NTRS2012

The Role of Lightning in Controlling Interannual Variability of Tropical Tropospheric Ozone and OH and its Implications for Climate

Nitrogen oxides (NO(x) = NO + NO2) produced by lightning make a major contribution to the production of the dominant tropospheric oxidants (OH and ozone). These oxidants control the lifetime of many trace gases including long-lived greenhouse gases, and control the source-receptor relationship of inter-hemispheric pollutant transport. Lightning is affected by meteorological variability, and therefore represents a potentially important tropospheric chemistry-climate feedback. Understanding how interannual variability (IAV) in lightning affects IAV in ozone and OH in the recent past is important if we are to predict how oxidant levels may change in a future warmer climate. However, lightning parameterizations for chemical transport models (CTMs) show low skill in reproducing even climatological distributions of flash rates from the Lightning Imaging Sensor (LIS) and the Optical Transient Detector (OTD) satellite instruments. We present an optimized regional scaling algorithm for CTMs that enables sufficient sampling of spatiotemporally sparse satellite lightning data from LIS to constrain the spatial, seasonal, and interannual variability of tropical lightning. We construct a monthly time series of lightning flash rates for 1998-2010 and 35degS-35degN, and find a correlation of IAV in total tropical lightning with El Nino. We use the IAV-constraint to drive a 9-year hindcast (1998-2006) of the GEOS-Chem 3D chemical transport model, and find the increased IAV in LNO(x) drives increased IAV in ozone and OH, improving the model fs ability to simulate both. Although lightning contributes more than any other emission source to IAV in ozone, we find ozone more sensitive to meteorology, particularly convective transport. However, we find IAV in OH to be highly sensitive to lightning NO(x), and the constraint improves the ability of the model to capture the temporal behavior of OH anomalies inferred from observations of methyl chloroform and other gases. The sensitivity of OH is explained using photochemical reaction rates which show a "magnification" effect of the initial lightning NO perturbation on OH primary production, HO(x) recycling, and OH loss frequencies. This influence on OH may represent a negative feedback, if lightning increases in a warming world..

Murray, Lee T.↗

NASA NTRSDate not supplied

The International Space Station Lightning Imaging Sensor: Performance, Applications, and Cross-Platform Science

The Lightning Imaging Sensor (LIS), an optically based lightning detector developed at NASA Marshall Space Flight Center, was launched to the International Space Station (ISS) in February 2017, detecting optical signatures of lightning with storm-scale horizontal resolution (4-km) during both day and night. ISS LIS data are available 1 March 2017 to present. Millisecond timing allows detailed intercalibration and validation with other spaceborne and ground-based lightning sensors. Initial comparisons with those other sensors suggest flash detection efficiency around 60% (diurnal variability of 51-75%), false alarm rate under 5%, timing accuracy better than 2 ms, and horizontal location accuracy around 3 km. The spatially uniform flash detection capability of ISS LIS from low-Earth orbit allows assessment of spatially varying flash detection efficiency for other sensors and networks, particularly the Geostationary Lightning Mappers (GLMs). ISS LIS provides research data suitable for investigations of lightning physics, climatology, thunderstorm processes, and atmospheric composition, as well as realtime lightning data for operational forecasting and aviation weather interests. ISS LIS enables enrichment and extension of the long-term global climatology of lightning from space, and is the only recent platform that extends the global record to higher latitudes (± 55°). The global spatial distribution of lightning from ISS LIS is broadly similar to previous datasets, with globally averaged seasonal/annual flash rates (3-year average: ~44 s) about 5-10% lower. This difference is likely due to reduced flash detection efficiency that will be mitigated in future ISS LIS data processing, as well as the shorter ISS LIS period of record. The expected land/ocean contrast in the diurnal variability of global lightning is also observed. The near-realtime ISS LIS data make the instrument important to operational weather forecasting and related applications, including public safety. Finally, ISS LIS is demonstrating utility as part (or potential part) of cross-platform studies examining a diverse array of topics, including lightning physics, thunderstorm processes, convective precipitation, and atmospheric composition.

Timothy Lang↗

NASA NTRSDate not supplied

Automated Detection and Analysis of Resident Space Objects with the 1.3-Meter Eugene Stansbery-Meter Class Autonomous Telescope

Optical telescopes dedicated to the detection of orbital debris employ large-area detectors that generate a large number of images each night. Such surveys require automated data analysis pipelines that process the images and detect moving objects. We present an overview of the data analysis pipeline employed by the 1.3-meter Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT) on Ascension Island, operated by NASA’s Orbital Debris Program Office. The pipeline enfolds the astrometric and photometric calibration of the images, star-trail removal, object detection, correlation over multiple sequential image frames, and orbital parameter estimation. The performance of the pipeline was investigated by means of Monte-Carlo simulations in which simulated object tracks were inserted into ES-MCAT images and then processed by the pipeline. This technique allows one to confidently estimate the completeness for the detection of resident space objects as a function of apparent magnitude and angular velocity. This paper discusses these techniques and provides examples using actual data.

Paul Hickson↗

NASA NTRS2023

Automated Detection and Analysis of Resident Space Objects with the 1.3-Meter Eugene Stansbery-Meter Class Autonomous Telescope

Optical telescopes dedicated to the detection of orbital debris employ large-area detectors that generate a large number of images each night. Such surveys require automated data analysis pipelines that process the images and detect moving objects. We present an overview of the data analysis pipeline employed by the 1.3-meter Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT) on Ascension Island, operated by NASA’s Orbital Debris Program Office. The pipeline enfolds the astrometric and photometric calibration of the images, star-trail removal, object detection, correlation over multiple sequential image frames, and orbital parameter estimation. The performance of the pipeline was investigated by means of Monte-Carlo simulations in which simulated object tracks were inserted into ES-MCAT images and then processed by the pipeline. This technique allows one to confidently estimate the completeness for the detection of resident space objects as a function of apparent magnitude and angular velocity. This paper discusses these techniques and provides examples using actual data.

Paul Hickson↗

NASA NTRSDate not supplied

Towards a Combined Low-Earth Orbit Lightning Climatology: Current Work and Assessing South Atlantic Anomaly Influence

This presentation discusses the current status and ongoing work towards a low-Earth orbit (LEO) lightning climatological product that includes both Lightning Imaging Sensors (LIS) and the Optical Transient Detector (OTD). The project builds upon the work by Cecil et al. (2014) to include the LIS on the International Space Station (ISS), featuring additional inter-instrumental comparisons to more accurately depict the unique capabilities of each instrument. A closer examination of the interference from the South Atlantic Anomaly (SAA) was also conducted on all three LEO sensors. The SAA is a region of the magnetosphere roughly spanning the south-central Atlantic wherein the inner Van Allen radiation belts are closer to Earth than anywhere else, subjecting spacecraft in LEO to significantly higher radiation flux levels. This radiation can produce interference with the LIS and OTD instruments, manifesting as non-lightning luminous events. While these events can be identified easily enough, they can occur in such quantities that they overwhelm the sensors’ processors and effectively ‘blind’ them. This is called the First-In First-Out (FIFO) buffer overflow, and this blinded time reduced the instruments’ view-time as a result. The FIFO overflow and view-time can reliably be used to track the SAA interference (Clark et al. 2024), which allows for the lightning counts attributable to the SAA to be assessed. The impact that the SAA had on the quality of observations from the LEO lightning instrumentation and the significance for the resulting climatological products was investigated. Substantial areas of interference were identified for all three instruments using the view-time and quality flags, each with a unique shape and temporal evolution. The temporal evolution and general region affected are of particular importance when constructing a climatological product, as there are notable reductions to view-time over prolonged periods across a lightning-rich region. However, a temporal element also makes isolating the subsequent impact on the lightning signal significantly more challenging. Lightning counts in this region are highly seasonal and exhibit inter-annual variability, which is compounded by the nature of LEO observations. This study includes preliminary analysis of the impact that the SAA has on the lightning counts given the notable impact shown in the metadata.

Austin G Clark↗

DOE OSTI2020

Incident exercise in a virtual environment

An incident simulation system supports an incident exercise in a virtual environment. The incident simulation system accesses a simulation plan defining an incident within a theater of operation. The incident simulation system simulates the incident exercise by displaying, to a participant in the incident exercise, images representing what the participant would see within the theater of operation as the participant moves within the theater of operation. The incident simulation system further simulates the incident by generating incident data indicating effects of the incident at target locations and at target times as the participant moves within the theater of operation. The incident simulation system further simulates the incident by displaying to the participant images representing the user experience that a detector would provide based on the generated incident data.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Influence of dissolved salts and impurities on seawater on heat transfer and fluid flow through fuel channels and debris bed

This project aims to better understand this mechanism and its effect on heat transfer. Specifically, experimental research was conducted to investigate the long term coolability issues in scaled test setups. Advanced diagnostic and measurement techniques were investigated and incorporated into an annular test facility and a debris bed test facility. The diagnostic techniques investigated included: radioactively tagged salt solution, Frisch collar radiation detector array, neutron and x-ray imaging systems, and a Rayleigh backscatter-based fiber-optic temperature system. Models were checked against the in-situ experimental data and recommendations were made for modeling purposes.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Incident exercise in a virtual environment

An incident simulation system supports an incident exercise in a virtual environment. The incident simulation system accesses a simulation plan defining an incident within a theater of operation. The incident simulation system simulates the incident exercise by displaying, to a participant in the incident exercise, images representing what the participant would see within the theater of operation as the participant moves within the theater of operation. The incident simulation system further simulates the incident by generating incident data indicating effects of the incident at target locations and at target times as the participant moves within the theater of operation. The incident simulation system further simulates the incident by displaying to the participant images representing the user experience that a detector would provide based on the generated incident data.

White, Gregory K.↗

DOE OSTI2022

Time-gated fast neutron transmission radiography system and method

The present disclosure relates to a time-gated fast neutron transmission radiography system and method. The system makes use of a pulsed neutron source for producing neutrons in a plurality of directions, with at least a subplurality of the neutrons being directed at an object to be imaged. The system also includes a neutron detector system configured to time-gate the detection of neutrons emitted from the pulsed neutron source to within a time-gated window.

Schmidt, Andrea↗

DOE OSTI2023

Incident exercise in a virtual environment

An incident simulation system supports an incident exercise in a virtual environment. The incident simulation system accesses a simulation plan defining an incident within a theater of operation. The incident simulation system simulates the incident exercise by displaying, to a participant in the incident exercise, images representing what the participant would see within the theater of operation as the participant moves within the theater of operation. The incident simulation system further simulates the incident by generating incident data indicating effects of the incident at target locations and at target times as the participant moves within the theater of operation. The incident simulation system further simulates the incident by displaying to the participant images representing the user experience that a detector would provide based on the generated incident data.

White, Gregory K.↗

NASA NTRS2012

New Techniques for High-Contrast Imaging with ADI: The ACORNS-ADI SEEDS Data Reduction Pipeline

We describe Algorithms for Calibration, Optimized Registration, and Nulling the Star in Angular Differential Imaging (ACORNS-ADI), a new, parallelized software package to reduce high-contrast imaging data, and its application to data from the Strategic Exploration of Exoplanets and Disks (SEEDS) survey. We implement seyeral new algorithms, includbg a method to centroid saturated images, a trimmed mean for combining an image sequence that reduces noise by up to approx 20%, and a robust and computationally fast method to compute the sensitivitv of a high-contrast obsen-ation everywhere on the field-of-view without introducing artificial sources. We also include a description of image processing steps to remove electronic artifacts specific to Hawaii2-RG detectors like the one used for SEEDS, and a detailed analysis of the Locally Optimized Combination of Images (LOCI) algorithm commonly used to reduce high-contrast imaging data. ACORNS-ADI is efficient and open-source, and includes several optional features which may improve performance on data from other instruments. ACORNS-ADI is freely available for download at www.github.com/t-brandt/acorns_-adi under a BSD license

Brandt, Timothy D.↗

NASA NTRS1971

Spaceborne electronic imaging systems

Criteria and recommended practices for the design of the spaceborne elements of electronic imaging systems are presented. A spaceborne electronic imaging system is defined as a device that collects energy in some portion of the electromagnetic spectrum with detector(s) whose direct output is an electrical signal that can be processed (using direct transmission or delayed transmission after recording) to form a pictorial image. This definition encompasses both image tube systems and scanning point-detector systems. The intent was to collect the design experience and recommended practice of the several systems possessing the common denominator of acquiring images from space electronically and to maintain the system viewpoint rather than pursuing specialization in devices. The devices may be markedly different physically, but each was designed to provide a particular type of image within particular limitations. Performance parameters which determine the type of system selected for a given mission and which influence the design include: Sensitivity, Resolution, Dynamic range, Spectral response, Frame rate/bandwidth, Optics compatibility, Image motion, Radiation resistance, Size, Weight, Power, and Reliability.

Source record↗

NASA NTRS1986

Operational characteristics of Wedge and Strip image readout systems

Application of the Wedge and Strip readout system in microchannel plate detectors for the Extreme Ultraviolet Explorer and FAUST space astronomy programs is discussed. Anode designs with high resolution (greater than 600 x 600 pixels) in imaging and spectroscopy applications have been developed. Extension of these designs to larger formats (100 mm) with higher resolution (3000 x 3000 pixels) are considered. It is shown that the resolution and imaging are highly stable, and that the flat field performance is essentially limited by photon statistics. Very high speed event response has also been achieved with output pulses having durations of less than 10 nanoseconds.

Siegmund, O. H. W.↗

DOE OSTI2023

Data fusion enhanced multi-modality wellbore integrity inspection system

A downhole multi-modality inspection system includes a first imaging device operable to generate first imaging data and a second imaging device operable to generate second imaging data. The first imaging device includes a first source operable to emit energy of a first modality, and a first detector operable to detect returning energy induced by the emitted energy of the first modality. The second imaging device includes a second source operable to emit energy of a second modality, and a second detector operable to detect returning energy induced by the emitted energy of the second modality. The system further includes a processor configured to receive the first imaging data and the second imaging data, and integrate the first imaging data with the second imaging data into an enhanced data stream. The processor correlates the first imaging data and the second imaging data to provide enhanced data for detecting potential wellbore anomalies.

Kasten, Ansas Matthias↗

DOE OSTI2021

Cepstral scanning transmission electron microscopy imaging of severe lattice distortions

The development of four-dimensional (4D) scanning transmission electron microscopy (STEM) using fast detectors has opened-up new avenues for addressing some of longstanding challenges in electron imaging. One of these challenges is how to image severely distorted crystal lattices, such as at a dislocation core. Here we develop a new 4D-STEM technique, called Cepstral STEM, for imaging disordered crystals using electron diffuse scattering. In contrast to analysis based on Bragg diffraction, which measures the average and periodic scattering potential, electron diffuse scattering can detect fluctuations caused by crystal disorder. Local fluctuations of diffuse scattering are captured by scanning electron nanodiffraction (SEND) using a coherent probe. The harmonic signals in electron diffuse scattering are detected through Cepstral analysis and used for imaging. By integrating Cepstral analysis with 4D-STEM, we demonstrate that information about the distortive part of electron scattering potential can be separated and imaged at nm spatial resolution. Here, we apply the technique to the analysis of a dislocation core in SiGe and lattice distortions in a high entropy alloy.

36 MATERIALS SCIENCE↗

NASA NTRS1982

Image science team

A substantial technology base of solid state pushbroom sensors exists and is in the process of further evolution at both GSFC and JPL. Technologies being developed relate to short wave infrared (SWIR) detector arrays; HgCdTe hybrid detector arrays; InSb linear and area arrays; passive coolers; spectral beam splitters; the deposition of spectral filters on detector arrays; and the functional design of the shuttle/space platform imaging spectrometer (SIS) system. Spatial and spectral characteristics of field, aircraft and space multispectral sensors are summaried. The status, field of view, and resolution of foreign land observing systems are included.

Ando, K.↗

NASA NTRS1975

Development of a spectroscopic photoelectric imaging Fabry-Perot interferometer preliminary observational results

In order to observe extended astronomical objects at high spatial and spectral resolution, a spectroscopic photoelectric imaging Fabry-Perot interferometer was constructed. Among the properties chosen for the instrument are an air-spaced, piezoelectrically scanned design allowing an accurately settable free spectral range and employing a single etalon of high finesse. Careful design of the etalon mountings and optical train preserves high ligh throughput. Spectra of single spatial elements with a photomultiplier were obtained, and an SEC vidicon detector was used to record a series of images through the interferometer while scanning the wavelength in discrete steps. The latter procedure yields sufficient information to reconstruct spectral features over the entire object, and for the conditions assumed, either series of observations requires only a small fraction of a rotational period for Jupiter or Saturn. An electronic control system was also constructed which permits rapid and flexible variation of the operational mode of the Fabry-Perot and its ancilliary devices so as to minimize loss of observational time.

Smith, W. H.↗