Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “experimentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Synthesis of stiffness and mass matrices from experimental vibration modes.

With highly complex structures, it is sometimes desirable to derive a dynamic model of the system from experimental vibration data. This paper presents algorithms for synthesizing the mass and stiffness matrices from experimentally derived modal data in a way which preserves the physical significance of the individual mass and stiffness elements. The synthesizing procedures allow for the incorporation of other mass and stiffness data, whether empirical or based on the analyst's insight. The mass and stiffness matrices are derived for a cantilever beam example and are compared with those obtained using earlier techniques.

Ross, R. G., Jr.↗
NASA NTRS1972

Experimental investigation of two-phase heat transfer in a porous matrix.

One-dimensional two-phase flow transpiration cooling through porous metal is studied experimentally. The experimental data is compared with a previous one-dimensional analysis. Good agreement with calculated temperature distribution is obtained as long as the basic assumptions of the analytical model are satisfied. Deviations from the basic assumptions are caused by nonhomogeneous and oscillating flow conditions. Preliminary derivation of nondimensional parameters which characterize the stable and unstable flow conditions is given. Superheated liquid droplets observed sputtering from the heated surface indicated incomplete evaporation at heat fluxes well in access of the latent energy transport. A parameter is developed to account for the nonequilibrium thermodynamic effects. Measured and calculated pressure drops show contradicting trends which are attributed to capillary forces.

Von Reth, R.↗
NASA NTRS1972

Experimental investigation of transient stimulated Raman scattering in a linearly dispersionless medium.

The results of numerical calculations of the transient stimulated Raman scattering reported previously have been verified experimentally under conditions where both linear dispersion and self-focusing effects were negligible. The existence of a delay between maxima of the laser and Stokes pulses is experimentally demonstrated for the first time, while the pulse shortening in time via Raman scattering is established more firmly than in previous work. The incident-laser-pulse duration, generated-Stokes-pulse duration, and delay between intensity maxima for the laser and Stokes pulses were measured with the two-photon absorption-fluorescence technique. The effective phonon-dephasing time is determined via spontaneous Raman scattering. By using these measured quantities, inferences are made as to the magnitude of the transient gain and the shape of the exciting picosecond laser pulse.

Carman, R. L.↗
NASA NTRS1972

Experimental and theoretical investigation of stress wave attenuation in fiber reinforced composites.

The propagation of an initialrcidrical pressure pulse through a linear elastic fiber reinforced composite medium is analysed, both experimentally and analytically. In the experiment, tests were performed on plates with single and multiple circular inclusions embedded in a matrix of lower characteristic impedance. Sharp compression pulses were generated at an edge of the plate. Strain gages were mounted on various positions of the plate to determine the attenuation of the transient stress in the fiber reinforced composite. The qualitative analytical treatment is based on the methods of propagating stress discontinuities. Computer programs were written to numerically determine the changes in the shape of the leading wave front and the stresses immediately behind it. Experimental results for the attenuation of stress wave on steel-aluminum and steel-brass fiber-matrix composites compared very well with the computed analytical results when the applied pressure is generated by small explosive charges. The results did not compare well when the applied pressure is generated by projectile impact.

Yang, J. C. S.↗
NASA NTRS1972

Experimental Hingeless Rotor Characteristics at Full Scale First Flap Mode Frequencies (including Rotor Frequency Response to Shaft Oscillations), Phase 3

The completion of the High Advance Ratio Research Program is reported. The primary objectives of the program were to experimentally determine the rotor frequency response to shaft pitching and rolling oscillations and to acquire steady response and frequency response data at high advance ratios for hingeless rotors with typical, full-scale, first flap mode natural frequencies. Secondary objectives of the program included the further evaluation of both the hub moment feedback control system and the simplified rigid blade flapping theory with respect to shaft oscillations. The bulk of the text is devoted to the presentation and examination of representative experimental results. All the analyzed test data are documented in tabular and/or graphical formats.

Kuczynski, W. A.↗
NASA NTRS1972

Experimental performance of an internal resistance heater for Langley 6-inch expansion tube driver

An experimental investigation of the heating characteristics of an internal resistance heating element was conducted in the driver of the Langley 6-inch expansion tube to obtain actual operating conditions, to compare these results to theory, and to determine whether any modification need be made to the heater element. The heater was operated in pressurized helium from 138. MN/sq m to 62.1 MN/sq m. This investigation revealed large temperature variations within the heater element caused primarily by area reductions at insulator locations. These large temperature variations were reduced by welding small tabs over all grooves. Previous predictions of heater element and driver gas temperature were unacceptable so new equations were derived. These equations predict element and gas temperature within 10 percent of the test data when either the constant power cycle or the interrupted power cycle is used. Visual observation of the heater element, when exposed to the atmosphere with power on, resulted in a decision to limit the heater element to 815 K. Experimental shock Mach numbers are in good agreement with theory.

Creel, T. R., Jr.↗
NASA NTRS1972

Analytical and experimental study of axisymmetric truncated plug nozzle flow fields

Experimental and analytical investigation of the flow field and base pressure of internal-external-expansion truncated plug nozzles are discussed. Experimental results for two axisymmetric, conical plug-cylindrical shroud, truncated plug nozzles are presented for both open and closed wake operations. These results include extensive optical and pressure data covering nozzle flow field and base pressure characteristics, diffuser effects, lip shock strength, Mach disc behaviour, and the recompression and reverse flow regions. Transonic experiments for a special planar transonic section are presented. An extension of the analytical method of Hall and Mueller to include the internal shock wave from the shroud exit is presented for closed wake operation. Results of this analysis include effects on the flow field and base pressure of ambient pressure ratio, nozzle geometry, and the ratio of specific heats. Static thrust is presented as a function of ambient pressure ratio and nozzle geometry. A new transonic solution method is also presented.

Muller, T. J.↗
NASA NTRS1972

An analytical and experimental investigation of rotating, non-capillary heat pipes

An approximate theoretical model is derived for laminar film condensation on the inside of a rotating, truncated cone, and is used to predict the heat transfer performance of rotating, non-capillary heat pipes for a wide variety of parametric conditions. Experimental results are presented for water, ethyl alcohol, and freon-113 in a stainless steel heat pipe rotating to speeds of 2800 rpm. Results show that these devices can be used effectively to transfer large quantities of heat in rotating systems. Predicted results agree to within + or - 20 percent of the experimental data. Dropwise condensation, instead of film condensation, improves heat pipe performance while the presence of non-condensible gases impairs performance.

Marto, P. J.↗
NASA NTRS1972

Vibration and loads in hingeless rotors. Volume 2: Experimental data

Descriptions, geometry, and technical data covering three rotor systems are presented. Tables of experimental data gathered during wind tunnel testing of two of the systems are included. Both analyzed experimental data, ready for comparison with theory, and the basic reduced data from which they were obtained are reported.

Watts, G. A.↗
NASA NTRS1973

A proposed experimental method for interpreting Doppler effect measurements and determining their precision

The principal problem in the measurement of the Doppler reactivity effect is separating it from the thermal reactivity effects of the expansion of the heated sample. It is shown in this proposal that the thermal effects of sample expansion can be experimentally determined by making additional measurements with porous samples having the same mass and/or volume as the primary sample. By combining these results with independent measurements of the linear temperature coefficient and the computed temperature dependence of the Doppler coefficient the magnitude of the Doppler coefficient may be extracted from the data. These addiational measurements are also useful to experimentally determine the precision of the reactivity oscillator technique used to measure the reactivity effects of the heated sample.

Klann, P. G.↗
NASA NTRS1973

Theoretical and experimental studies of reentry plasmas

A viscous shock-layer analysis was developed and used to calculate nonequilibrium-flow species distributions in the plasma layer of the RAM vehicle. The theoretical electron-density results obtained are in good agreement with those measured in flight. A circular-aperture flush-mounted antenna was used to obtain a comparison between theoretical and experimental antenna admittance in the presence of ionized boundary layers of low collision frequency. The electron-temperature and electron-density distributions in the boundary layer were independently measured. The antenna admittance was measured using a four-probe microwave reflectometer and these measured values were found to be in good agreement with those predicted. Measurements were also performed with another type of circular-aperture antenna and good agreement was obtained between the calculations and the experimental results. A theoretical analysis has been completed which permits calculation of the nonequilibrium, viscous shock-layer flow field for a sphere-cone body. Results are presented for two different bodies at several different altitudes illustrating the influences of bluntness and chemical nonequilibrium on several gas dynamic parameters of interest. Plane-wave transmission coefficients were calculated for an approximate space-shuttle body using a typical trajectory.

Dunn, M. G.↗
NASA NTRS1973

Experimental investigation of orthotropic panel flutter at arbitrary yaw angles, and comparison with theory

Flutter characteristics for yaw angles between 15 deg and 90 deg were determined experimentally for two types of corrugation-stiffened panels: those with weak twisting stiffness and those with strong twisting stiffness. By mounting the panels on a remotely controlled turntable, good definition of the flutter boundaries was obtained by rotating the panels into and out of flutter. Flutter tests were conducted at M = 2 and M = 1.6. Before testing, vibration tests and analyses were also performed. The experimental flutter data is compared with flutter theory for orthotropic panels utilizing quasi-steady aerodynamics. Five different corrugated panels were tested consisting of one single skin panel having a length-to-width ratio of 5 on clamped supports and four different square double skin panels on discrete flexible supports. The investigation indicated that flutter speed for corrugated panels is highly dependent on yaw angle. Reasonable flutter correlation between analysis and test was obtained for moderate yaw angles, but extreme sensitivity to structural parameters made the correlation at large yaw angles uncertain.

Shyprykevich, P.↗
NASA NTRS1973

Study of an experimental technique for application to structural dynamic problems

An experimental program was conducted to determine the feasibility of using subscale plastic models to determine the response of full-scale aerospace structural components to impulsive, pyrotechnic loadings. A monocoque cylinder was impulsively loaded around the circumference of one end, causing a compressive stress wave to propagate in the axial direction. The resulting structural responses of two configurations of the cylinder (with and without a cutout) were recorded by photoelasticity, strain gages, and accelerometers. A maximum dynamic stress concentration was photoelastically determined and the accelerations calculated from strain-gage data were in good agreement with those recorded by accelerometers. It is concluded that reliable, quantitative structural response data can be obtained by the experimental techniques described in this report.

Snell, R. F.↗
NASA NTRS1973

Analytical and experimental studies of shock interference heating in hypersonic flows

An analytical and experimental study is presented of the aerodynamic heating resulting from six types of shock interference patterns encountered in high speed flow. Centerline measurements of pressure and heat transfer distributions on basic bodies were obtained in four wind tunnels for Mach numbers from 6 to 20, specific heat ratios from 1.27 to 1.67, and free stream Reynolds numbers from 3 million to 25.6 million per meter. Peak heating and peak pressures up to 17 and 7.5 times stagnation values, respectively, were measured. In general, results obtained from semiempirical methods developed for each of the six types of interference agreed with the experimental peaks.

Keyes, J. W.↗
NASA NTRS1973

Experimental investigation of liquid propellant dynamics in a double cylindrical tank

Experimental data are presented for verifying the computer program for computing propellant oscillation modes and frequencies for tanks of any shape, fill level, or orientation. The experimental apparatus including the tank, support and excitation system, and instrumentation is described along with the procedures. Results showing slosh forces and moments are tabulated for different fill heights. It was found that for the vertical tank excited along the long axis, the frequencies of the higher modes are significantly higher than with the tank tilted. Little difference was noted for excitation along the short axis.

Ransleben, G. F., Jr.↗
NASA NTRS1973

A critical review of the experimental data for developed free turbulent shear layers

Experimental shear layer data are reviewed and the results are compared to numerical predictions for three test cases. It was concluded from the study that many, if not most, of the apparent inconsistencies which exist in the interpretation of the experimental data for free shear layers result from confusing data taken in developed turbulent flows with those taken in transitional or developing flows. Other conclusions drawn from the study include the following: (1) The effects of Mach number are more uncertain primarily because of limited data and the absence of any turbulence measurements for supersonic shear layers. (2) The data available for heterogeneous shear layers are not sufficient to clearly establish the effect of density ratio on mixing rate.

Birch, S. F.↗
NASA NTRS1973

Experimental stress analysis of large plastic deformations in a hollow sphere deformed by impact against a concrete block

An experimental plastic strain measurement system is presented for use on the surface of high velocity impact test models. The system was used on a hollow sphere tested in impact against a reinforced concrete block. True strains, deviatoric stresses, and true stresses were calculated from experimental measurements. The maximum strain measured in the model was small compared to the true failure strain obtained from static tensile tests of model material. This fact suggests that a much greater impact velocity would be required to cause failure of the model shell structure.

Morris, R. E.↗