Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “evolution of the Universe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Nonlinear Evolution of Instabilities in a Laminar Separation Bubble at a Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

Hypersonic flow↗

Ion Chemistry in Atmospheric and Astrophysical Plasmas

There are many differences and also remarkable similarities between the ion chemistry and physics of planetary ionospheres and the ion chemistry and physics of astronomical environments beyond the solar system. In the early Universe, an expanded cooling gas of hydrogen and helium was embedded in the cosmic background radiation field and ionized by it. As the Universe cooled by adiabatic expansion, recombination occurred and molecular formation was driven by catalytic reactions involving the relict electrons and protons. Similar chemical processes are effective in the ionized zones of gaseous and planetary nebulae and in stellar winds where the ionization is due to radiation from the central stars, in the envelopes of supernovae where the ionization is initiated by the deposition of gamma-rays, in dissociative shocks where the ionization arises from electron impacts in a hot gas and in quasar broad-line region clouds where the quasar is responsible for the ionization. At high altitudes in the atmospheres of the Jovian planets, the main constituents are hydrogen and helium and the ion chemistry and physics is determined by the same processes, the source of the ionization being solar ultraviolet radiation and cosmic rays. After the collapse of the first distinct astronomical entities to emerge from the uniform flow, heavy elements were created by nuclear burning in the cores of the collapsed objects and distributed throughout the Universe by winds and explosions. The chemistry and physics became more complicated. Over 90 distinct molecular species have been identified in interstellar clouds where they are ionized globally by cosmic ray impacts and locally by radiation and shocks associated with star formation and evolution. Complex molecules have also been found in circumstellar shells of evolved stars. At intermediate and low altitudes in the Jovian atmospheres, the ion chemistry is complicated by the increasing abundance of heavy elements such as carbon, and an extensive array of complex molecules has been predicted. Reactions involving heavy elements dominate the structure of the ionspheres of the terrestrial planets and the satellites Titan and Triton.

Dalgarno, A.↗

Liners and Low Luminosity AGN in the ROSAT Database

This program has led to a series of papers being written and published in the Astrophysical Journal. Together these papers try to explain major parts of the LINER and low luminosity AGN puzzle. One paper ('Accretion Disk Instabilities, Cold Dark Matter Models, and Their Role in Quasar Evolution', Hatziminaoglou E., Siemiginowska A., & Elvis M., 2001, ApJ, 547, 90) describes an analytical model for the evolution of the quasar luminosity function. By combining the Press-Schechter formalism for the masses of initial structures with the luminosity distribution for a population of single mass black holes given by an unstable accretion disk an almost complete end-to-end physics-based model of quasar evolution is produced. In this model black holes spend 75% of their time in a low accretion state (at L(Edd)). This low state population of black holes is likely to be observed as the LINER and low luminosity AGNs in the local universe. Another paper ('Broad Emission Line Regions in AGN: the Link with the Accretion Power', Nicastro F., 2000, ApJ Letters, 530, L65) gives a physical basis for why low state black holes appear as LINERS. By linking the Lightman-Eardley instability in an accretion disk to the ori.gin of a wind that contains the broad emission line cloud material this model explains the large widths seen in these lines as being the Keplerian velocity of the disk at the instability radius. For LINERS the key is that below an accretion rate of 10(exp -3)M(sub Edd)the Lightman-Eardley instability falls within the innermost stable orbit of the disk, and so leaves the entire disk stable. No wind occurs, and so no broad emission lines are seen. Most LINERS are likely to be black holes in this low state. Tests of this model are being considered.

Elvis, Martin↗

Advanced Characterization Capabilities for Nuclear Materials via Nuclear Science User Facilities (NSUF)

Advanced post-irradiation examination (PIE) techniques are required to design new or improved nuclear materials, characterize, and understand in-core behavior of fuel and materials, and support the qualification of new reactor materials. The Nuclear Science User Facilities (NSUF) is the U.S. Department of Energy Office of Nuclear Energy's only designated nuclear science user facility. NSUF provides researchers access to PIE capabilities at Idaho National Laboratory and at a diverse mix of university, national laboratory and industrial partner institutions. The PIE capabilities include novel destructive and non-destructive techniques for radiation damage characterization, such as advanced diffraction techniques (X-ray, electron, or neutron) coupled to extreme environments; in-situ observation of microstructural evolution under irradiation; in-situ irradiation to monitor corrosive attack in coolant environments; in-situ irradiation and mechanical testing; and test methods for synergistic effects of superimposed extreme environments (temperature, irradiation, stress, corrosion) on materials behaviors. This talk will provide an overview of NSUF PIE capabilities.

36 MATERIALS SCIENCE↗

Halting Oxygen Evolution to Achieve Long Cycle Life in Sodium Layered Cathodes

Oxygen redox chemistries at high voltage have materialized as a revolutionary paradigm for cathodes with high-energy density; however, they are plagued by the challenges of labile oxygen loss and rapid degradations upon cycling, even after concerted endeavors from the research community. Here we propose a multi-concentration stratagem propelled by entropy reinforcement to enhance the electronic structure disorder (ESD) at high desodiation states for impeding undesired oxygen mobility and ensuring controlled oxygen activity, elucidated by density functional theory calculations. The increased disorder strengthens the reversible electrochemistry of lattice oxygen redox, leading to effectively suppressed P−O structural evolution and highly stable localized TMO 6 octahedral environments, as demonstrated by soft/hard X-ray absorption spectroscopy. Furthermore, through a comparative analysis of sodium-layered cathodes with different configuration entropy, we reveal that a high-entropy state induced by cationic disordering has the capacity to perturb cationic redox boundaries, significantly restraining the formation of detrimental O′3 phases. As a consequence, the high-voltage cycling stability has been greatly upgraded, up to 4.4 V versus Na + /Na, with an impressive 90.1 % capacity retention at 1 C over 100 cycles and 76.1 % capacity retention at 2 C over 300 cycles. In conclusion, the resilient oxygen redox, enabled through the control of ESD, broadens the horizons for entropy engineering and lays the foundation for advancements in high-energy, long-cycling, and safe batteries.

25 ENERGY STORAGE↗

Investigating the Effects of Copper Impurity Deposition on the Structure and Electrochemical Behavior of Hydrogen Evolution Electrocatalyst Materials

Electrolysis of impure water (such as seawater) has recently garnered research interest as it may enable hydrogen production at reduced costs. However, the tendency of impurity ions and other species to degrade electrocatalysts and membranes within an electrolyzer is a serious challenge. Here, we investigate the effects of copper impurities of varying concentrations on the hydrogen evolution reaction (HER) using platinum electrocatalysts. A decrease of current density is observed with an increasing copper concentration. By comparing the effect of ionic impurities on current density at different concentrations, we gain insight into how impurities can interfere with the HER at different potentials. Surface characterization of the electrodes reveals differences in the morphology and extent of copper deposition on HER-active platinum vs inactive gold electrodes. This enables an improved understanding of how copper nucleates and grows on the two types of electrodes under different electrochemical conditions while also confirming deposition in low-concentration cases, as present in seawater. The results indicate that copper electrodeposition competes with the HER, and the nature of copper electrodeposition varies depending on the electrocatalytic activity of the electrode. This study provides insight toward catalyst design that can withstand the effects of impurity-induced degradation over extended use.

08 HYDROGEN↗

Supramolecular Metal‐Organic Framework Electrocatalysts With Hydration‐Adaptive Gallery Expansion and Linker‐Mediated Distal Ni‐Co Cooperation Enable Framework‐Retentive Oxygen Evolution

Atomic‑level tailoring of electronic communication between spatially separated metal sites offers a route to accelerate multielectron electrocatalysis. We report Ni-TPTC, Co-TPTC, and heterobimetallic Ni-Co-TPTC supramolecular metal-organic frameworks (SMOFs) for the oxygen evolution reaction (OER) built from a terphenyl‑tetracarboxylate (TPTC) linker. Single-crystal X-ray diffraction of heterobimetallic Ni–Co–TPTC reveals trans-bis-aqua octahedral chains assembled into a π-stacked, hydrogen-bonded lattice and confirms retention of the parent architecture, while powder X-ray diffraction supports an isostructural Co analog. In 1.0 M KOH, Ni-Co-TPTC reaches 20 mA cm −2 at 350 mV and maintains operation at ∼60 mA cm −2 for 45 h with modest decay of the initial current. Time‑dependent ex situ diffraction shows dominant framework reflections with low‑angle shifts consistent with gallery dilation (d‑spacing ∼7.7 → ∼9.2 Å) during early operation, while Co K‑edge X‑ray absorption and microscopy reveal Co‑rich oxide/oxyhydroxide‑like domains at longer times that correlate with decay. X‑ray photoelectron spectroscopy, quantified by the Remote Binding‑Energy Differential, tracks composition‑dependent Ni-Co polarization, and DFT free‑energy analysis suggests that a model Ni-Co environment lowers the Co‑centered potential‑limiting step by ∼0.24 eV relative to the Co‑only framework. Furthermore, these results suggest that framework‑retentive expansion and distal Ni-Co coupling can drive OER activity before gradual deligation and oxide formation mark longer‑time degradation.

Supramolecular metal-organic frameworks (SMOFs)↗

A global numerical study of radon-222 and lead-210 in the atmosphere using the AES and York University CDT General Circulation Model (AYCG)

The Canadian Climate Center (CCC) GCM has been modified to allow its use for studies in atmospheric chemistry. The initial experiments reported here have been run to test and allow sensitivity studies of the new transport module. The impact of different types of parameterization for the convective mixing have been studied based on the large scale evolution of Rn-222 and Pb-210. Preliminary results have shown that the use of a scheme, which mixes unstable columns over a very short time scale, produces a global distribution of lead that agrees in some aspects with observations. The local impact of different mixing schemes on a short lived tracer like the radon is very important.

Beagley, Stephen R.↗

Defect engineering in nickel via electrodeposition following low temperature annealing

Electrodeposited nickel coatings are characterized by high densities of crystalline defects including dislocations, growth twins, and hydrogen bubbles/voids, arising from the non-equilibrium nature of deposition. While these metastable features influence as-deposited properties, their evolution under low temperature annealing remains unexplored. Here, in this study, we demonstrate that low temperature annealing (200 °C) induces significant microstructural rearrangement without grain growth, enabling defect engineering through thermally assisted dislocation motion and twin boundary migration. Notably, we observe faceted twin boundaries and dislocation organization into extended networks, which have been rarely reported under such annealing conditions. These transformations are attributed to hydrogen-assisted defect mobility, facilitated by the release or redistribution of hydrogen trapped during deposition. These structural transformations correlate with a significant enhancement in mechanical properties, including a twofold increase in yield strength and improved ductility. Our findings highlight the role of trapped hydrogen in mediating low-temperature defect mobility and twin boundary evolution, offering a unique pathway for microstructural tuning of metallic coatings through controlled annealing.

36 - MATERIALS SCIENCE↗

CoSn-type NiIn1–xSbx (0 ≤ x ≤ 0.17): Site-Selective Substitution, Electronic Structure, Chemical Bonding, and Structural Transformation

CoSn-type intermetallic compounds have emerged as a model platform for Kagome-derived flat-band physics, where subtle chemical perturbations can strongly influence electronic structure and phase stability. Here, we present a combined experimental and theoretical study of Sb-substitution in CoSn-type NiIn1–xSbx (0 ≤ x ≤ 0.17) to elucidate the interplay between site selectivity, solubility limit, chemical bonding, and electronic structure. Rietveld refinements on Neutron powder diffraction data confirmed the selective Sb-substitution at the electron-rich In2 (2d) site forming the honeycomb substructure, while the In1 (1a) site within the Kagome layer remains exclusively occupied by In. Density functional theory (DFT) calculations revealed that pristine CoSn-type NiIn hosts Ni 3d-dominated flat bands near the Fermi level (EF), originating from the Kagome-like Ni substructure. Partial replacement of In by Sb within the honeycomb layer alters these flat-band features below EF, reducing the density of states and suppressing the flat-band topology near the Fermi level. Orbital-resolved electronic structure and chemical-bonding analyses show that Sb-substitution enhances Ni-p-block (In/Sb) covalency and optimizes charge compensation, stabilizing the CoSn-type structure up to the solubility limit x ≈ 0.17. Beyond the limit, the higher-Sb compositions show satellite reflections consistent with an incommensurately modulated phase. These results establish a link between site-selective chemical substitution, bonding optimization, and flat-band electronic structure evolution, providing fundamental insights into how chemical substitution influences the electronic properties of Kagome-based intermetallic compounds.

Roy, Nilanjan [National Institute of Technology Si↗

Imaging of dynamic processes in materials with a laser-wakefield accelerator

Betatron x rays generated from laser-wakefield accelerators are a promising source for imaging dynamic processes in materials. Here, we present proof-of-concept imaging of microstructural evolution in a hypermonotectic Al-Bi alloy, which consists of liquid Bi particles in a solid Al matrix. The images capture the elongation and fragmentation of Bi particles upon isothermal annealing. Because of the femtosecond time scale of the betatron source, the images are not subject to motion blur, whereas the accessibility of the source allows for studies of long-term processes such as annealing. The high-resolution data reveal that the evolution of Bi particles is mediated by an interplay of grain-boundary wetting and morphological instability, in stark contrast to an earlier proposal for (inverse) coarsening.

Alloys↗

Comment on “QCD factorization with multihadron fragmentation functions”

We make several comments on the recent work in Rogers et al. [Phys. Rev. D 111, 056001 (2025)] while also reaffirming and adding to the work in Pitonyak et al. [Phys. Rev. Lett. 132, 011902 (2024)]. We show that the factorization formula for 𝑒 + ⁢𝑒 − → (ℎ 1 ⋯ ℎ 𝑛 )⁢𝑋 in Rogers et al. is equivalent to a version one can derive using the definition of a 𝑛-hadron fragmentation function (FF) introduced in Pitonyak et al.. In addition, we scrutinize how to generalize the number density definition of a single-hadron FF to a 𝑛-hadron FF, arguing that the definition given in Pitonyak et al. should be considered the standard one while the definition in Rogers et al. has no clear interpretation. We also emphasize that the evolution equations for dihadron FFs (DiFFs) in Pitonyak et al. have the same splitting functions as those for single-hadron FFs. Therefore, the DiFF (and 𝑛-hadron FF) definitions in Pitonyak et al. have a natural number density interpretation and, contrary to what is stated in Rogers et al., are consistent with collinear factorization using the standard hard factors and evolution kernels.

Pitonyak, D. [Lebanon Valley College, Annville, PA↗

Impact of QCD energy evolution on observables in heavy-ion collisions

Here, we study how the inclusion of energy dependence as dictated by quantum chromodynamic (QCD) small-x evolution equations affects key observables in ultra-relativistic heavy-ion collisions. Specifically, we incorporate JIMWLK evolution into the IP-Glasma framework, which serves as the initial condition for a simulation pipeline that includes viscous relativistic hydrodynamics and a hadronic afterburner. This approach enables a consistent modeling of highly energetic nuclei across varying Bjorken-x values, which are relevant for different collision energies and rapidity regions. In comparison to the standard IP-Glasma setup without small-x evolution, we observe pronounced changes in particle multiplicities and spectral distributions, especially in smaller systems and at the highest available energies. We further explore effects on anisotropic flow observables and correlations between mean transverse momentum and elliptic flow. Our findings underscore the critical role of nonlinear QCD evolution in accurately modeling the early stages of heavy-ion collisions, as well as its implications for extracting transport properties of the quark-gluon plasma.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Dating fractures using luminescence

Rock fracturing (cracking) is a universal process that drives and limits chemical degradation, sediment production and erosion, and deterioration of infrastructure. Despite extensive research gains in rock mechanics on one hand and geochronology on the other, there remains a glaring gap in our ability to understand the long term evolution of natural, in situ fractures. Here we develop a novel fracture exposure dating technique, grounded in modern advances in luminescence geochronology. We apply our new dating method to a granitic boulder from a glacial outwash terrace in California, US. We conclude that the longest, clast-splitting E-W fracture appeared shortly after the boulder's deposit, whereas the secondary N-S fracture appeared 5 ka after the deposition, approximately correlating with the Last Glacial Maximum and Younger Dryas periods of the region, respectively. However, dating of the third fracture (<< 50 µm width) which does not fully split the rock, is ambiguous due to negligible daylight penetration and poor determination of fracture width. The fracture dating method presented herein brings with it the potential to decipher relationships that are crucial for the interpretation and modeling of, for example, long-term landscape and atmospheric evolution relating rock weathering to climate change and erosion.

58 GEOSCIENCES↗

Shrub and sedge rhizosphere communities display distinct affinities toward exudates and soil organic matter degradation: a quantitative stable isotope probing analysis

Warming temperatures are accelerating permafrost thaw and changing tundra vegetation, where woody shrubs are displacing sedges. Shrubs, such as Betula nana, and sedges, such as Eriophorum vaginatum, exhibit distinct life strategies including unique root-associated, or rhizosphere microbial communities. As permafrost thaws it unlocks previously unavailable carbon and nutrient sources resulting in deeper roots and a translocation of rhizosphere communities. Because permafrost microbial communities contain lower diversity and biomass than rhizosphere communities, the coalescence of rhizosphere and permafrost microbial communities could alter soil organic matter (SOM) degradation rates and increase greenhouse gas emissions. To identify metabolic strategies across distinct rhizosphere and permafrost microbial communities we conducted an isotope tracing incubation experiment. We inoculated thawed permafrost with shrub and sedge rhizosphere communities while adding exudates or water daily and compared this to an uninoculated control. After 46 days, we spiked samples with 18O enriched water or 13C enriched exudates and measured isotope incorporation into microbial DNA with quantitative stable isotope probing (qSIP). Our results indicate that exudate additions had little effect on uninoculated permafrost communities but the addition of exudates and rhizosphere inoculants had a compounding effect on respiration rates. We found that soils inoculated with shrub rhizosphere communities contained a mixture of exudate and SOM degraders while soils inoculated with sedge rhizosphere communities contained mainly SOM degraders. Finally, we found that individual microbial taxa exhibited maximum growth rates under specific combinations of microbial inoculant communities and exudate addition treatments. Our results reveal that microbial niches are strongly influenced by substrate preferences and community context, and suggest that a reduction in sedges and an expansion of shrubs may provide a mechanism by which permafrost carbon losses are mitigated through corresponding shifts in microbial communities and their substrate preferences.

Schaefer, Sean R [Natural Resources and Earth Syst↗

Evaluation of Engineered Barrier Systems (FY2022 Report)

This report describes research and development (R&D) activities conducted during Fiscal Year 2022 (FY22) specifically related to the Engineered Barrier System (EBS) R&D Work Package in the Spent Fuel Waste Science and Technology (SFWST) Campaign supported by the United States (U.S.) Department of Energy (DOE). The R&D activities focus on understanding EBS component evolution and interactions within the EBS, as well as interactions between the host media and the EBS. The R&D team represented in this report consists of individuals from Sandia National Laboratories, Lawrence Berkeley National Laboratory (LBNL), Los Alamos National Laboratory (LANL), and Vanderbilt University. EBS R&D work also leverages international collaborations to ensure that the DOE program is active and abreast of the latest advances in nuclear waste disposal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗