Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1955

Investigation of Porous Gas-Heated Leading-Edge Section for Icing Protection of a Delta Wing

A tip section of a delta wing having an NACA 0004-65 airfoil section and a 600 leading-edge sweepback was equipped with a porous leading-edge section through which hot gas was 'bled for anti-icing. Heating rates for anti-icing were determined for a wide range of icing conditions. The effects of gas flow through the porous leading-edge section on airfoil pressure distribution and drag in dry air were investigated. The drag increase caused by an ice formation on the unheated airfoil was measured for several icing conditions. Experimental porous surface- to free-stream convective heat-transfer coefficients were obtained in dry air and compared with theory. Adequate icing protection was obtained at all icing conditions investigated. Savings in total gas-flow rate up to 42 percent may be obtained with no loss in anti-icing effectiveness by sealing half the upper-surface porous area. Gas flow through the leading-edge section had no appreciable effect on airfoil pressure distribution. The airfoil section drag increased slightly (5-percent average) with gas flow through the porous surface. A heavy glaze-ice formation produced after 10 minutes of icing caused an increase in section drag coefficient of 240 percent. Experimental convective heat-transfer coefficients obtained with hot-gas flow through the porous area in dry air and turbulent flow were 20 to 30 percent lower than the theoretical values for a solid surface under similar conditions. The transition region from laminar to turbulent flow moved forward as the ratio of gas velocity through the porous surface to air-stream velocity was increased.

Bowden, Dean T.↗
NASA NTRS1976

Acoustic radiation and surface pressure characteristics of an airfoil due to incident turbulence

The noise and unsteady surface pressure characteristics of an isolated airfoil in a uniform mean velocity, homogeneous, nearly isotropic turbulence field were investigated. Experiments were performed with a 23 cm chord, two-dimensional airfoil over a Mach number range of 0.1 to 0.5. Far-field noise spectra and directivity as well as surface pressure spectra and cross-spectra were obtained. Incident turbulence statistics were documented. Theory applied to predict far-field noise and surface pressure characteristics from measured inflow turbulence statistics showed good agreement with measurement. The theoretical formulation represents a first-principles solution providing absolute level prediction without recourse to empirical or adjustable constants, and takes into account compressibility as well as source noncompactness effects. All chordwise portions of the airfoil radiated directly to the far-field, the leading edge to the dominant noise producing region. The effect of angle of attack on noise and surface pressures is small. The interaction of incident turbulence of approximately 4 percent intensity with an airfoil was found to be a broadband noise source of high intensity relative to other noise sources.

Paterson, R. W.↗
NASA NTRS1983

Internal and edge cracks in a plate of finite width under bending

Internal and edge cracks were studied by using Reissner's transverse shear theory. The effect of stress-free boundaries on the stress intensity factors in plates under bending were investigated. Among the results found, particularly interesting are those relating to the limiting cases of the crack geometries. The numerical results are given for a single internal crack, two collinear cracks, and two edge cracks. The effect of Poisson's ratio on the stress intensity factors was studied.

Boduroglu, H.↗
NASA NTRS2014

Active Figure Control Effects on Mounting Strategy for X-Ray Optics

As part of ongoing development efforts at MSFC, we have begun to investigate mounting strategies for highly nested xray optics in both full-shell and segmented configurations. The analytical infrastructure for this effort also lends itself to investigation of active strategies. We expect that a consequence of active figure control on relatively thin substrates is that errors are propagated to the edges, where they might affect the effective precision of the mounting points. Based upon modeling, we describe parametrically, the conditions under which active mounts are preferred over fixed ones, and the effect of active figure corrections on the required number, locations, and kinematic characteristics of mounting points.

Kolodziejczak, Jeffery J.↗
NASA NTRS1984

The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

Grantz, A. C.↗
NASA NTRS1985

Lee-side flow over delta wings at supersonic speeds

An experimental investigation of the lee-side flow on sharp leading-edge delta wings at supersonic speeds has been conducted. Pressure data were obtained at Mach numbers from 1.5 to 2.8, and three types of flow-visualization data (oil-flow, tuft, and vapor-screen) were obtained at Mach numbers from 1.7 to 2.8 for wing leading-edge sweep angles from 52.5 deg to 75 deg. From the flow-visualization data, the lee-side flows were classified into seven distinct types and a chart was developed that defines the flow mechanism as a function of the conditions normal to the wing leading edge, specifically, angle of attack and Mach number. Pressure data obtained experimentally and by a semiempirical prediction method were employed to investigate the effects of angle of attack, leading-edge sweep, and Mach number on vortex strength and vortex position. In general, the predicted and measured values of vortex-induced normal force and vortex position obtained from experimental data have the same trends with angle of attack, Mach number, and leading-edge sweep; however, the vortex-induced normal force is underpredicted by 15 to 30 percent, and the vortex spanwise location is overpredicted by approximately 15 percent.

Miller, D. S.↗
NASA NTRS2014

Analysis of Active Figure Control Effects on Mounting Strategy for X-Ray Optics

As part of ongoing development efforts at MSFC, we have begun to investigate mounting strategies for highly nested x-ray optics in both full-shell and segmented configurations. The analytical infrastructure for this effort also lends itself to investigation of active strategies. We expect that a consequence of active figure control on relatively thin substrates is that errors are propagated to the edges, where they might affect the effective precision of the mounting points. Based upon modeling, we describe parametrically, the conditions under which active mounts are preferred over fixed ones, and the effect of active figure corrections on the required number, locations, and kinematic characteristics of mounting points.

Kolodziejczak, Jeffrey J.↗
NASA NTRS1981

The unsteady suction analogy and applications

A method of the unsteady suction analogy is developed using the unsteady quasi-vortex-lattice method which accurately predicts unsteady leading-edge and side-edge suction forces, and applies to any reduced frequencies. The importance of vortex lag is demonstrated, and damping derivatives, including roll and pitch damping derivatives with reduced frequencies and angles of attack are accurately predicted. Agreement of predicted pitch stiffness derivatives, however, is found to depend on the Reynolds number, possible aeroelastic effect, and the degree of edge-separated vortex flow on the model. Applications to the prediction of longitudinal dynamic stability derivatives for slender wings at high angles of attack are also presented.

Lan, C. E.↗
NASA NTRS1993

An experimental parametric study of geometric, Reynolds number, and ratio of specific heats effects in three-dimensional sidewall compression scramjet inlets at Mach 6

The effects of the decrease in the ratio of specific heats have been investigated in generic 3D sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air. In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗
NASA NTRS1977

The influence of stripe width on the threshold current of double-heterojunction lasers

Experimental measurements of the threshold current of oxide-isolated stripe laser as a function of stripe width and p-layer resistivity are presented. A calculation of the influence of carrier outdiffusion has been made, including the effect of current leakage beyond the stripe edges. The calculated threshold increase is in substantial agreement with experiment for stripe widths down to about 10 microns. The data also yield an effective diffusion length of about 7 microns for the lasers studied. Deviations between experimental and calculated thresholds occurring at stripe widths of 4-6 microns are represented by an empirical curve which is compared with previously published calculations of threshold gain.

Ladany, I.↗
NASA NTRS2002

The Opposition Effect: A Very Unusual Case

The reflection of electromagnetic radiation from a planetary regolith involves a combination of geometric and physical optics processes which contribute to the signal returned to the remote observer. The geometric optics effects are the product of singly and multiply scattered radiation from the surfaces of the regolith particles, combined with radiation which has undergone various combinations of transmission through one or more regolith grains followed by one or more scatterings from other particles. The physical optics effects include diffraction of radiation around the edges of large irregular particles and cooperative coherent scattering between particles which are small when compared to the wavelength of the incident radiation. These effects produce measurable changes in the intensity and polarization of reflected light as a function of illumination and viewing geometry. In particular, as phase angle becomes small, the reflectance of a particulate material will increase non-linearly and exhibit the 'opposition effect'. In the planetary science context, the phase curve, and in particular the size of the opposition surge and the width of the phase curve near zero degrees, have been attributed to two processes commonly called 'shadow hiding' (SHOE) and 'coherent backscattering' (CBOE).

Nelson, R. M.↗
NASA NTRS1932

The aerodynamic characteristics of a model wing having a split flap deflected downward and moved to the rear

Tests were made on a model wing with three different sized split trailing-edged flaps, in the NACA 7 by 10 foot wind tunnel. The flaps were formed of the lower rear portion of the wing and were rotated downward about axes at their front edges. The lift, drag, and center of pressure were measured with the axis in its original position and also with it moved back in even steps to the trailing edge of the main wing, giving in effect an increase in area. The split flaps when deflected about their original axis locations gave slightly higher maximum lift coefficients than conventional trailing-edge flaps, and the lift coefficients were increased still further by moving the axes toward the rear. The highest value of C(sub L max), which was obtained with the largest flap hinged at 90 per cent of the chord from the leading edge, was 2.52 as compared with 1.27 for the basic wing.

Weick, Fred E↗
DOE OSTI2024

Nitrogen Vacancy Centers in Diamond for Stress Sensing Applications: Theory and Experiments

Sensing of stress under high elevated environmental conditions with high resolution has critical importance for range of applications including earth’s subsurface scanning and geological CO2 storage monitoring. Using first principles density functional theory (DFT) approach combined with the theoretical modelling of low energy Hamiltonian, here we investigate a novel approach to detect unprecedented level of pressure by taking advantage of solid-state electron’s spin of Nitrogen vacancy (NV) centers in nanodiamond. We computationally explore the effect of strain on the defect band edges and band gaps by varying the lattice parameters of diamond supercell hosting a single NV center. A low energy Hamiltonian is developed that includes effect of stress on the energy level of ±1 spin manifold at the ground state. By quantifying the energy level shift and split, we predict the pressure sensing of up to 0.3 MPa/√Hz. We show superiority of the quantum sensing over traditional optical sensing techniques by discussing our results from DFT and theoretical modelling for the frequency shift per unit pressure. The proposed quantum stress sensing could be useful to measure earth’s subsurface vibrations. Our results open avenues for development of sensing technology with a high sensitivity and resolution under extreme pressure conditions that potentially has a wider applicability than existing pressure sensing technologies.

Paudel, Hari P.↗
NASA NTRS1974

Effect of upper-surface blowing on static longitudinal stability of a swept wing

A low-speed wind-tunnel investigation was conducted on a sharp-edged 75 deg delta wing, to determine the effect of upper-surface blowing on static longitudinal stability characteristics. The model incorporated nozzles, located at 0.50 mean aerodynamic chord length, supplied by compressed air to provide blowing on the upper surface. A full span trailing-edge flap was also tested as an additional high-lift device. The angle of attack was varied from 0 to 24 deg for a range of thrust coefficients from 0 to 0.45. The results of the static force tests showed that favorable increments in static longitudinal stability and lift were obtained using upper-surface blowing.

Coe, P. L., Jr.↗
DOE OSTI2026

Comparison of plasma response models for RMP effects on the divertor and scrape-off layer in KSTAR

Resonant magnetic perturbations (RMPs) are beneficial for control of edge localized modes (ELMs) in tokamaks. Nevertheless, a side effect of RMPs is the appearance of helical striations in the particle and heat loads onto divertor targets. The extent and field line connection of these striations is significantly altered by the plasma response to external perturbations. For an ELM suppressed high confinement (H-mode) plasma at KSTAR, magnetic footprints are computed by FLARE based on plasma response from GPEC, MARS-F, M3D-C1 and JOREK with substantial differences in the resulting footprints (from 2 cm to 14 cm). This is reflected in EMC3-EIRENE simulations of the resulting heat loads: it is found that either the peak value or the extent of the striations appears to be overestimated compared to infrared camera measurements. Reasonable agreement can only be achieved for the smallest footprint for lower input power and lower cross-field transport, or for higher upstream density and radiative power losses.

Frerichs, H. [Univ. of Wisconsin, Madison, WI (Uni↗
NASA NTRS1993

An Experimental Parametric Study of Geometric, Reynolds Number, and Ratio of Specific Heats Effects in Three-Dimensional Sidewall Compression Scramjet Inlets at Mach 6

Since mission profiles for airbreathing hypersonic vehicles such as the National Aero-Space Plane include single-stage-to-orbit requirements, real gas effects may become important with respect to engine performance. The effects of the decrease in the ratio of specific heats have been investigated in generic three-dimensional sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane (where gamma=1.22) and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air (where gamma=1.4). In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗
NASA NTRS2005

The Influence of Projectile Trajectory Angle on the Simulated Impact Response of a Shuttle Leading Edge Wing Panel

In support of recommendations by the Columbia Accident Investigation Board, a team has been studying the effect of debris impacting the reinforced carbon-carbon panels of the shuttle leading edge. The objective of this study was to examine the effect of varying parameters of the debris trajectory on the damage tolerance. Impacts at the upper and lower surface and the apex of the leading edge were examined. For each location, trajectory variances included both the alpha and beta directions. The results of the analysis indicated in all cases the beta sweep decreased the amount of damage to the panel. The increases in alpha resulted in a significant increase in damage to the RCC panel. In particular, for the lower surface, where the alpha can increase by 10 degrees, there was a nearly 40% increase in the impulse. As a result, it is recommended that for future analyses, a 10 degree offset in alpha from the nominal trajectory is included for impacts on the lower surface. It is also recommended to assume a straight aft, or zero beta, trajectory for a more conservative analysis.

Spellman, Regina L.↗
NASA NTRS2015

A 3-D Computational Study of a Variable Camber Continuous Trailing Edge Flap (VCCTEF) Spanwise Segment

Results of a computational study carried out to explore the effects of various elastomer configurations joining spanwise contiguous Variable Camber Continuous Trailing Edge Flap (VCCTEF) segments are reported here. This research is carried out as a proof-of-concept study that will seek to push the flight envelope in cruise with drag optimization as the objective. The cruise conditions can be well off design such as caused by environmental conditions, maneuvering, etc. To handle these off-design conditions, flap deflection is used so when the flap is deflected in a given direction, the aircraft angle of attack changes accordingly to maintain a given lift. The angle of attack is also a design parameter along with the flap deflection. In a previous 2D study,1 the effect of camber was investigated and the results revealed some insight into the relative merit of various camber settings of the VCCTEF. The present state of the art has not advanced sufficiently to do a full 3-D viscous analysis of the whole NASA Generic Transport Model (GTM) wing with VCCTEF deployed with elastomers. Therefore, this study seeks to explore the local effects of three contiguous flap segments on lift and drag of a model devised here to determine possible trades among various flap deflections to achieve desired lift and drag results. Although this approach is an approximation, it provides new insights into the "local" effects of the relative deflections of the contiguous spanwise flap systems and various elastomer segment configurations. The present study is a natural extension of the 2-D study to assess these local 3-D effects. Design cruise condition at 36,000 feet at free stream Mach number of 0.797 and a mean aerodynamic chord (MAC) based Reynolds number of 30.734x10(exp 6) is simulated for an angle of attack (AoA) range of 0 to 6 deg. In the previous 2-D study, the calculations revealed that the parabolic arc camber (1x2x3) and circular arc camber (VCCTEF222) offered the best L/D characteristics and minimum drag in cruise. In the present 3-D study, calculations show that for the same C(sub t), the 3-D circular arc camber wing segment produces the largest drag for a given lift, larger than either of the two 2-D configurations, as was also conjectured in the previous study. This study indicates a wing stall around 4.5 deg angle of attack.

Camber↗