Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Eutectic superalloys by edge-defined, film-fed growth

The feasibility of producing directionally solidified eutectic alloy composites by edge-defined, film-fed growth (EFG) was carried out. The three eutectic alloys which were investigated were gamma + delta, gamma/gamma prime + delta, and a Co-base TaC alloy containing Cr and Ni. Investigations into the compatibility and wettability of these metals with various carbides, borides, nitrides, and oxides disclosed that compounds with the largest (negative) heats of formation were most stable but poorest wetting. Nitrides and carbides had suitable stability and low contact angles but capillary rise was observed only with carbides. Oxides would not give capillary rise but would probably fulfill the other wetting requirements of EFG. Tantalum carbide was selected for most of the experimental portion of the program based on its exhibiting spontaneous capillary rise and satisfactory slow rate of degradation in the liquid metals. Samples of all three alloys were grown by EFG with the major experimental effort restricted to gamma + delta and gamma/gamma prime + delta alloys. In the standard, uncooled EFG apparatus, the thermal gradient was inferred from the growth speed and was 150 to 200 C/cm. This value may be compared to typical gradients of less than 100 C/cm normally achieved in a standard Bridgman-type apparatus. When a stream of helium was directed against the side of the bar during growth, the gradient was found to improve to about 250 C/cm. In comparison, a theoretical gradient of 700 C/cm should be possible under ideal conditions, without the use of chills. Methods for optimizing the gradient in EFG are discussed, and should allow attainment of close to the theoretical for a particular configuration.

Hurley, G. F.↗
NASA NTRS1974

Analysis of edge impact stresses in composite plates

The in-plane edge impact of composite plates, with or without a protection strip, is investigated. A computational analysis based on the Fast Fourier Transform technique is presented. The particular application of the present method is in the understanding of the foreign object damage problem of composite fan blades. The method is completely general and may be applied to the study of other stress wave propagation problems in a half space. Results indicate that for the protective strip to be effective in reducing impact stresses in the composite the thickness must be equal or greater than the impact contact dimension. Large interface shear stresses at the strip - composite boundary can be induced under impact.

Moon, F. C.↗
NASA NTRS1975

Effect of wall edge suction on the performance of a short annular dump diffuser with exit passage flow resistance

The effect of wall edge suction on the performance of a short annular dump diffuser having a perforated plate flow resistance device in the exit passage was evaluated. Testing was conducted with air at near ambient pressure and temperature at inlet Mach numbers of 0.18 and 0.27 with suction rates up to 13.5 percent. Results show that pressure recovery downstream of the perforated plate was improved significantly by suction. Optimum performance was obtained with the flow resistance plate located at one inlet passage height downstream of the dump plane.

Juhasz, A. J.↗
NASA NTRS1975

Cold-air experimental investigation of a turbine with blade trailing edge coolant ejection. 1: Single-stage turbine

Tests were made on a 0.762-meter-tip-diameter research turbine to determine the effect of blade coolant flow on its aerodynamic performance. Both stator and rotor blades had trailing-edge slots for coolant ejection. The turbine was tested over a range of speed and pressure ratio. High primary efficiencies, calculated on the basis of primary air only, were obtained. The efficiency attained was identical to that reported for the turbine from a previous investigation were only slotted stator blades where incorporated in the turbine and tested. And it also compares with results for the turbine with solid blading. Independently varying the rotor coolant flow showed that rotor cooling imposed a severe penalty on turbine efficiency. The thermodynamic efficiency, which accounts for the ideal energies of both blade coolant flows, decreased linearly with rotor coolant at a rate of about 0.7 percent per percent rotor coolant fraction.

Schum, H. J.↗
NASA NTRS1975

Directionally solidified lamellar eutectic superalloys by edge-defined, film-fed growth

A program was performed to scale up the edge-defined, film-fed growth (EFG) method for the gamma/gamma prime-beta eutectic alloy of the nominal composition Ni-19.7 Cb - 6 Cr-2.5 Al. Procedures and problem areas are described. Flat bars approximately 12 x 1.7 x 200 mm were grown, mostly at speeds of 38 mm/hr, and tensile tests on these bars at 25 and 1000 C showed lower strength than expected. The feasibility of growing hollow airfoils was also demonstrated by growing bars over 200 mm long with a teardrop shaped cross-section, having a major dimension of 12 mm and a maximum width of 5 mm.

Hurley, G. F.↗
NASA NTRS1975

Maximum two-phase flow rates of subcooled nitrogen through a sharp-edged orifice

Data are presented of an experiment in which subcooled liquid nitrogen was discharged through a sharp-edged orifice at flow rates near the maximum. The data covered a range of inlet stagnation pressures from slightly above saturation to twice the thermodynamic critical pressure. The data were taken along five separate inlet stagnation isotherms ranging from 0.75 to 1.035 times the thermodynamic critical temperature. The results indicate that subcooled liquids do not choke or approach maximum flow in an asymptotic manner even though the back pressure is well below saturation; and orifice flow coefficients are not constant as is frequently assumed. A metastable jet appears to exist which breaks down if the difference between back pressure and saturation pressure is large enough.

Simoneau, R. J.↗
NASA NTRS1975

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow visualization study showed that strong Karman vortices are developed behind the blunt trailing edge of a plate when the free stream velocities over both surfaces are equal. These vortices tend to disappear when the surface velocities are unequal. This observation provided an explanation for the occurrence and disappearance of the lip noise often present in coaxial jets. Vortex formation and lip noise occurred at a Strouhal number of about 0.2 based on the lip thickness and the average of the external steady-state velocities. Results from theoretical calculations of the vortex formation, based on an inviscid, incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Brinich, P. F.↗
NASA NTRS1974

Simple methods for determining the virtual origin of turbulent boundary layers in hypersonic flow on sharp-edged flat plates

Two methods for determining the virtual origin of turbulent boundary layers in hypersonic flow are evaluated. The results of the analyses are restricted to wind-tunnel models having sharp-edged surfaces with zero or small pressure gradients. Virtual origin and skin friction estimates from these two methods are compared with values from a base method for which the virtual origin is calculated from the measured momentum thickness at a station downstream of boundary layer transition.

Hopkins, E. J.↗
NASA NTRS1975

Edge-defined film-fed growth of beta-alumina and Mg-substituted beta-alumina

High Na vapor pressure, peritectic decomposition, and high reactivity of the melt complicate the growth of beta-alumina crystals. These difficulties were overcome by using a high-pressure (300 psig) growth chamber, Na2O-rich melts, and Ir for all surfaces in contact with the melt. These procedures were combined with the edge-defined film-fed growth technique to produce single-crystal beta-alumina tubes and ribbons.

Morrison, A. D.↗
NASA NTRS1975

Maximum two-phase flow rates of subcooled nitrogen through a sharp-edged orifice

An experiment was conducted and data are presented in which subcooled liquid nitrogen was discharged through a sharp-edged orifice at flow rates near the maximum. The data covered a range of inlet stagnation pressure from slightly above saturation to twice the thermodynamic critical pressure. The data were taken along five separate inlet stagnation isotherms ranging from 0.75 to 1.035 times the thermodynamic critical temperature. The results indicate that: (1) subcooled liquids do not choke or approach maximum flow in an asymptotic manner even though the back pressure is well below saturation; (2) orifice flow coefficients are not constant as is frequently assumed. A metastable jet appears to exist which breaks down if the difference between back pressure and saturation pressure is large enough.

Simoneau, R. J.↗
NASA NTRS1975

Transonic pressure measurements and comparison of theory to experiment for an arrow-wing configuration. Volume 1: Experimental data report, base configuration and effects of wing twist and leading-edge configuration

A wind tunnel test of an arrow-wing-body configuration consisting of flat and twisted wings, as well as a variety of leading- and trailing-edge control surface deflections, was conducted at Mach numbers from 0.4 to 1.1 to provide an experimental pressure data base for comparison with theoretical methods. Theory-to-experiment comparisons of detailed pressure distributions were made using current state-of-the-art attached and separated flow methods. The purpose of these comparisons was to delineate conditions under which these theories are valid for both flat and twisted wings and to explore the use of empirical methods to correct the theoretical methods where theory is deficient.

Manro, M. E.↗
NASA NTRS1975

Boundary-detection algorithm for locating edges in digital imagery

The author has identified the following significant results. Initial development of a computer program which implements a boundary detection algorithm to detect edges in digital images is described. An evaluation of the boundary detection algorithm was conducted to locate boundaries of lakes from LANDSAT-1 imagery. The accuracy of the boundary detection algorithm was determined by comparing the area within boundaries of lakes located using digitized LANDSAT imagery with the area of the same lakes planimetered from imagery collected from an aircraft platform.

Myers, V. I.↗
NASA NTRS1976

Turbine vane gas film cooling with injection in the leading edge region from a single row of spanwise angled holes

An experimental study of gas film cooling was conducted on a 3X size model turbine vane. Injection in the leading edge region was from a single row of holes angled in a spanwise direction. Measurements of the local heat flux downstream from the row of coolant holes, both with and without film coolant flow, were used to determine the film cooling performance presented in terms of the Stanton number ratio. Results for a range of coolant blowing ratio, M = 0 to 2.0, indicate a reduction in heat flux of up to 15 to 30 percent at a point 10 to 11 hole diameters downstream from injection. An optimum coolant blowing ratio corresponds to a coolant-to-freestream velocity ratio in the range of 0.5. The shallow injection angle resulted in superior cooling performance for injection closest to stagnation, while the effect of injection angle was insignificant for injection further from stagnation.

Lecuyer, M. R.↗
NASA NTRS1976

Noise reduction tests of large-scale-model externally blown flap using trailing-edge blowing and partial flap slot covering

Noise data were obtained with a large-scale cold-flow model of a two-flap, under-the-wing, externally blown flap proposed for use on future STOL aircraft. The noise suppression effectiveness of locating a slot conical nozzle at the trailing edge of the second flap and of applying partial covers to the slots between the wing and flaps was evaluated. Overall-sound-pressure-level reductions of 5 db occurred below the wing in the flyover plane. Existing models of several noise sources were applied to the test results. The resulting analytical relation compares favorably with the test data. The noise source mechanisms were analyzed and are discussed.

Mckinzie, D. J., Jr.↗
NASA NTRS1975

High-attitude low-speed static aerodynamic characteristics of an F-4D fighter airplane model with leading edge slats

An investigation was conducted to determine the effects of two-position leading edge slats on the low speed aerodynamic characteristics of a swept wing twin-jet supersonic fighter airplane model at high angle of attack and various Reynolds numbers. The investigation was performed at a Mach number of 0.20 over a range of angle of attack from 19 deg to 90 deg and angles of slideslip from -10 deg to 30 deg and Reynolds numbers from 1.97 to 13.12 million per meter.

Monfort, J. C.↗
NASA NTRS1976

New convergence criteria for the vortex-lattice models of the leading-edge separation

The convergence criterion for the vortex-lattice technique which deals with delta wings exhibiting significant leading-edge separation was studied. It was shown that one can predict pressure distributions without irregularities which agree fairly well with experimental data (which show some irregularities of their own) by replacing the system of discrete vortex lines with a single concentrated core. This core has a circulation equal to the algebraic sum of the circulations around the discrete lines and is located at the centroid of these lines. Moreover, there is a requirement that the position and strength of the core must converge as the number of elements increases. Because the calculation of the position and strength of the core is much less involved than the calculation of the loads, this approach has the additional desirable feature of requiring less computational time.

Kandil, O. A.↗
NASA NTRS1976

Unsteady flow past wings having sharp-edge separation

A vortex-lattice technique is developed to model unsteady, incompressible flow past thin wings. This technique predicts the shape of the wake as a function of time; thus, it is not restricted by planform, aspect ratio, or angle of attack as long as vortex bursting does not occur and the flow does not separate from the wing surface. Moreover, the technique can be applied to wings of arbitrary curvature undergoing general motion; thus, it can treat rigid-body motion, arbitrary wing deformation, gusts in the freestream, and periodic motions. Numerical results are presented for low-aspect rectangular wings undergoing a constant-rate, rigid-body rotation about the trailing edge. The results for the unsteady motion are compared with those predicted by assuming quasi-steady motion. The present results exhibit hysteretic behavior.

Atta, E. H.↗
NASA NTRS1976

A limiting analysis for edge effects in angle-ply laminates

A zeroth order solution for edge effects in angle ply composite laminates using perturbation techniques and a limiting free body approach was developed. The general method of solution for laminates is developed and then applied to the special case of a graphite/epoxy laminate. Interlaminar stress distributions are obtained as a function of the laminate thickness to width ratio h/b and compared to existing numerical results. The solution predicts stable, continuous stress distributions, determines finite maximum tensile interlaminar normal stress for two laminates, and provides mathematical evidence for singular interlaminar shear stresses.

Hsu, P. W.↗