Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dissolving”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Evaluating the efficacy of DGT to quantify copper in stormwater at end-of-pipe

In many cases, stormwater compliance monitoring is labor intensive, expensive, and largely unsuccessful in providing the data needed to support stormwater management goals. To help address these issues, diffusive gradients in thin film (DGTs), time-integrative passive samplers for metals, were evaluated to monitor copper in stormwater runoff. DGTs were co-located with traditional autosamplers within the stormwater conveyance systems at Naval Base San Diego (NBSD) to provide a direct comparison with composite sampling. DGTs were exposed in the laboratory to flow-averaged composite samples from NBSD stormwater conveyance systems. These experiments showed increasing uptake over time (range = 1.5 to 24 h) for copper, with positive, linear correlations (r2>0.980) between exposure duration and copper mass accumulated. However, it appears that the corresponding calculations of the DGT-labile fraction (CDGT) relative to the dissolved fraction fluctuated across the different exposure durations. In general, trends observed for CDGT measurements from the field were consistent with trends in the lab DGT exposures and traditional dissolved metal measurements from composite samples. Finally, time-weighted average copper concentrations from DGTs deployed for the first and second parts of storm events were within 30% of measurements from DGTs that were deployed for the entire storm event in the same stormwater vault. Cumulatively, these results show promise for continuous monitoring with DGTs as an approach that produces data more representative of exposure to the receiving environment during episodic events than data from traditional grab or composite chemistry sampling, and can represent significant cost savings.

Diffusive Gradient in Thin Films, stormwater, trac↗

Cookoff experiments of a melt cast explosive (Comp-B3)

Validated models of melt cast explosives exposed to accidental fires are essential for safety analysis. In the current work, we provide several experiments that can be used to develop and validate cookoff models of melt cast explosives such as Comp-B3 composed of 60:40 wt% RDX:TNT. We present several vented and sealed experiments from 2.5 mg to 4.2 kg of Comp-B3 in several configurations. We measured pressure, spatial temperature, and ignition time. Some experiments included borescope images obtained during both vented and sealed decomposition. We observed the TNT melt, the suspension of RDX particles in the melt, bubble formation caused by RDX decomposition, and bubble-induced mixing of the suspension. The RDX suspension did not completely dissolve, even as temperatures approached ignition. Our results contrast with published measurements of RDX solubility in hot TNT that suggest RDX would be completely dissolved at these high temperatures. These different observations are attributed to sample purity. We did not observe significant movement of the two-phase mixture until decomposition gases formed bubbles. Bubble generation was inhibited in our sealed experiments and suppressed mixing.

42 ENGINEERING↗

Direct in-situ observation of early age void evolution in sustainable cement paste containing fly ash or limestone

This paper uses fast X-ray Computed Tomography (fCT) to study the change in air-filled voids during hydration of portland cement pastes of different water to cement ratios and with fly ash and limestone additives between 30 min and 12 h of hydration with deionized and de-aired water. For the deionized samples, the total volume of the air-filled voids increased during the induction period and decreased as the acceleration period began and finally stayed constant. The samples with 20% replacement of fly ash and 20% replacement of limestone showed the same trends as the OPC samples but with a reduction in the observed air-filled void formation. The air-filled void distribution in these samples changed from a limited number of large voids at the beginning of the measurements to a system with a significantly greater number of uniformly distributed smaller voids. The changes in the air-filled voids were not significant in pastes made with 50% fly ash or with de-aired water in the same testing condition. This might be explained by differences in pore solution chemistry and a reduced amount of dissolved air in the mixing water. A mechanism is proposed for a change in ionic concentration in solution to cause release of the dissolved air within the mixing water.

Cement hydration↗

Cryo-based Structural Characterization and Growth Model of Salt Film on Metal

Metal salt films play a critical role in high rate dissolution processes such as within an active pit. However, structural and compositional characterization of salt films is challenging owing to the dynamic nature of the dissolving interface. Here, the salt film formed on SS304 one-dimensional artificial pit surface was directly characterized using flash freezing and cryo-based focused ion beam/scanning electron microscopy. The salt film exhibits a porous structure. Ni is co-located with Fe in the salt film, indicating the formation of co-precipitated salt containing Fe2+ and Ni2+. Additionally, a salt film growth model is presented based on ion transport.

Salt film, Pitting corrosion, Cryogenic, Cryo-FIB/↗

Advanced supercritical water-based process concepts for treatment and beneficial reuse of brine in oil/gas production

Produced water generated from oil/gas reservoirs is a cost burden for oil/gas producers, with over 21 billion barrels of the waste generated in 2019. Average disposal costs range from 4.00–8.00·bbl -1 , with up to 20·bbl -1 spent on transportation alone. Dissolved solids content is a contributing factor which limits economical treatment options for this waste stream. This work proposes a novel technique that can handle high salinity waste, employing favorable properties past the critical point of water. In this study, process simulation of two supercritical water desalination (SCWD) scenarios was completed. Zero liquid discharge (ZLD) and brine concentration operating scenarios were compared, weighing the associated economics and benefits for each case. The results were shown to be economically feasible for brines with a high dissolved solids content, ranging from 3.49 to 17.28·bbl -1 in an expanded sensitivity analysis.

42 ENGINEERING↗

Mineral Recovery Enhanced Desalination (MRED) process: An innovative technology for desalinating hard brackish water

Desalination of water containing high concentrations of calcium, dissolved carbon dioxide, sulfate, silica and other sparingly soluble salts is difficult because of the scaling potential. An innovative pre-treatment scheme was investigated at bench scale that selectively removes these constituents and produces a soft water to enable desalination with high feed water recovery. The process first removes dissolved carbon dioxide by air stripping at low pH. Magnesium is removed by precipitation at high pH. Calcium is removed by ion exchange (IX), and sulfate is removed by nanofiltration (NF). Cation regenerant from IX, containing calcium, and concentrate from NF, containing sulfate, is combined to precipitate gypsum. Concentrate from the desalination process consisting of a concentrated NaCl solution is used to regenerate the IX resins. The selective precipitation, IX, and NF processes were tested in laboratory experiments and produced magnesium hydroxide and gypsum at greater than 90% and 95% purity respectively. A process model was developed to calculate process performance, mass and liquid flow rates. Finally, the MRED process offers the following benefits: 1) greater recovery of brackish feedwater by a desalination process, 2) recovery of marketable commodities and 3) reduction in the volume and mass of waste products from the treatment process.

42 ENGINEERING↗

Combined electrocoagulation-microfiltration-membrane distillation for treatment of hydraulic fracturing produced water

Hydraulic fracturing flowback and produced water is a highly impaired wastewater containing dissolved salts polar and non-polar organic compounds, oil and surfactants. Here a combined electrocoagulation - microfiltration – membrane distillation process has been used to treat this wastewater. Electrocoagulation followed by microfiltration was used to pretreat the wastewater prior membrane distillation. The initial total dissolved solids (TDS) concentration was extremely high being 245,300 mg L -1 . After electrocoagulation, the total organic carbon (TOC) was reduced from 120 mg L -1 to 64 mg L -1 . Tangential flow microfiltration using a 0.1 μm pore size polyethersulfone membrane was used to separate the particulate matter after electrocoagulation and to further reduce the TOC to 44 mg L -1 . Membrane distillation was used to desalinate the pretreated produced water resulting in a high quality treated water (TDS of 56 mg L -1 and TOC 1 mg L -1 ). Three membranes with very different surface morphology were used: commercially available polyvinylidene fluoride, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers and multiwalled carbon nanotube coated polytetrafluoroethylene. The TDS in the retentate increased to over 350,000 mg L -1 . During membrane distillation, the temperature of the feed tank was maintained at 36 °C while the feed entered the module at 60 °C in order to minimize scaling on the membrane. The surface properties of an ideal membrane that is resistant to wetting and provides high flux is likely to depend on the TDS and properties of the wastewater.

42 ENGINEERING↗

Economic assessment of a multistage surface-heated vacuum membrane distillation process for the treatment of hypersaline produced water

Here, the treatment and disposal of hypersaline produced water remains a challenge, particularly for oil and gas producers in the Permian basin where production wells generate significant amounts of wastewater, and the traditional method of injecting wastewater into disposal wells is coming under increasing scrutiny. Here we investigate the viability of using solar energy to power a multi-stage, surface heated, vacuum membrane distillation (SHVMD) with energy recovery to treat hypersaline produced wastewater from Midland, Texas. Membrane distillation is a process that can desalinate waters with high total dissolved solids concentration, and when incorporated into a system with surface heating and energy recovery can achieve high water recovery rates. Model results show that a 6-stage SHVMD system with a 54.4 % water recovery rate and a gained output ratio (GOR) of 3.28 has the potential to be economically viable when used to treat hypersaline produced water in the Permian basin. Assuming energy costs of $\$0.03$/kWh thermal and $\$0.12$kWh electric , we estimate a project net present value (NPV) of $\$225,525$ and an internal rate of return (IRR) of 13.5 % when an air cooled condensor is used to cool the distillate and a NPV of $\$570,791$ and IRR of 24.52 % when a liquid coooling source is available.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Incorporating corrosion design constraints in desalination process optimization: A case study in mechanical vapor compression

Corrosion is an expensive and complex challenge for desalination, yet current design approaches do not explicitly account for corrosion mechanisms in process modeling and technoeconomic analysis. Here, to address this gap, we present a workflow for incorporating corrosion design constraints directly into desalination process optimization models. We develop surrogate models for general and localized corrosion metrics as functions of temperature, pH, salinity, dissolved oxygen, and material using data from OLI Systems’ Corrosion Analyzer. We then integrate these surrogates as corrosion design constraints in a cost-optimization MVC model that minimizes the levelized cost of water (LCOW). For a case study of mechanical vapor compression (MVC) treating seawater across a range of recoveries, we find dissolved oxygen (DO) is the dominant driver of localized corrosion, and thus of cost-optimal material choice and operating conditions. Reducing the DO from 8 mg/L to 0.5 mg/L reduces the LCOW by 15-35%, informing the breakeven costs for implementing DO removal or selecting highly corrosion-resistant alloys. This framework is broadly applicable across corrosion types, materials, and components and enables desalination process design that minimizes capital costs.

36 MATERIALS SCIENCE↗

A nutrient limitation mosaic in the eastern tropical Indian Ocean

The Indian Ocean accounts for about one fifth of global ocean net primary production but remains undersampled relative to other major ocean basins. The eastern tropical Indian Ocean is characterized by extremely low concentrations of both macronutrients and the micronutrient iron. In this work, we measured concentrations of dissolved and particulate trace metals (Fe, Mn, Zn, Pb) in the upper ocean along the GO-SHIP IO9N transect (28° S to 17° N, mostly along the 95° E meridian) during a cruise in April 2016. Cellular quotas (metal/C) of Fe, Mn, Co, Ni, Cu, and Zn were measured in small eukaryotic flagellates (2-7 μm). Deckboard bottle incubation experiments were conducted at one station in each of three putative biogeochemical regions: southern Indian Ocean gyre (S10, 28-10° S); equatorial Indian Ocean (EqIO, 10° S - 5° N); Bay of Bengal (BoB, 5-17° N). Nitrate and phosphate were below detection limits in surface waters across the transect. Dissolved and particulate Fe were < 0.2 nM south of 10° N and lowest in the EqIO. Cellular Fe/C quotas were approximately 6 μmoL/mol and did not vary along the transect, nor did cellular Mn/C or Co/C quotas. Cellular Ni/C and Zn/C quotas were significantly higher at the southern terminus. Nutrient addition experiments indicated that N was the primary limiting nutrient for autotrophs using chlorophyll $a$ as a proxy, but biomass measurements of specific phytoplankton groups pointed to a more complex nutrient limitation mosaic. Prochlorococcus was limited by N in the EqIO but by multiple nutrients (N, P, and/or Fe) in the BoB. Synechococcus was limited by N in the EqIO and BoB, while small (< 20 μm) eukaryotic phytoplankton were limited by N in the EqIO and by multiple nutrients in the BoB. Stoichiometric comparisons of cells and underlying source waters indicate a gradient of N and Fe stress along the transect. These data demonstrate that autotroph communities are poised near multiple nutrient limitation horizons in extremely oligotrophic waters far from micronutrient sources.

54 ENVIRONMENTAL SCIENCES↗

Inorganic Carbon Turnover caused by Digestion of Carbonate Sands and Metabolic Activity of Holothurians

Recent measurements have shown that holothurians (sea cucumbers) play an important role in the cycling of CaCO3 in tropical coral reef systems through ingestion and processing of carbonate sediment. In this study inorganic additional aspects of carbon turnover were determined in laboratory incubations of Holothuria atra, H. leucospilota and Stichopus herrmanni from One Tree Reef, Great Barrier Reef. The pH values of the gut lumen ranged from 6.1 to 6.7 in animals with empty digestive tracts as opposed to 7.0 to 7.6 when digestive tracts were filled with sediment. Empty gut volume estimates for H. atra and S. herrmanni were 36 ± 4 mL and 151 ± 14 mL, respectively. Based on these measurements it is estimated that these species process 19 ± 2kg and 80 ± 7kg CaCO3 sand yr-1 per individual, respectively. The annual dissolution rates of H. atra and S. herrmanni of 6.5±1.9g and 9.6±1.4g, respectively, suggest that 0.05±0.02% and 0.1±0.02% of the CaCO3 processed through their gut annually is dissolved. During the incubations the CaCO3 dissolution was 0.07±0.01%, 0.04±0.01% and 0.21±0.05% of the fecal casts for H. atra, H. leucospilota and S. herrmanni, respectively. The CaCO3 saturation state for both aragonite and calcite minerals during laboratory incubations decreased markedly due to a greater increase in dissolved inorganic carbon (DIC) relative to total alkalinity (AT) as a result of respiration by the animals. Our results support the hypothesis that deposit feeders such as sea cucumbers play an important ecological role in the coral reef CaCO3 cycle.

activity↗

Vanadium redox flow battery efficiency and durability studies of sulfonated Diels Alder poly(phenylene)s

Sulfonated Diels Alder poly(phenylene) (SDAPP) was examined for vanadium redox flow battery (VRFB) use. The ion exchange capacity (IEC) was varied from 1.4, 1.6 and 2.0 meq/g in order to tune the proton conductivity and vanadium permeability. Coulombic efficiencies between 92 to 99% were observed, depending on IEC (lower IEC, higher coulombic efficiencies). In all cases the SDAPP displayed comparable energy efficiencies (88 - 90%) to Nafion 117 (88%) at 50mA/cm2. Membrane durability also was dependent on IEC; SDAPP with the highest IEC lasted slightly over 50 cycles while SDAPP with the lowest IEC lasted over 400 cycles and testing was discontinued only due to time constraints. Accelerated vanadium lifetime studies were initialed with SDAPP, by soaking films in a 0.1 M V5+ and 5.0 M total SO4-2 solution. The rate of degradation was also proportional with IEC; the 2 meq/g sample dissolved within 376 hours, the 1.6 meq/g sample dissolved after 860 hours, while the 1.4 meq/g sample broke apart after 1527 hours.

accelerated lifetime testing↗

Pt Catalyst Degradation in Aqueous and Fuel Cell Environments studied via In-Operando Anomalous Small-Angle X-ray Scattering

The evolution of Pt nanoparticle cathode electrocatalyst size distribution in a polymer electrolyte membrane fuel cell (PEMFC) was followed during accelerated stress tests using in-operando anomalous small-angle X-ray scattering (ASAXS). This evolution was compared to that observed in an aqueous electrolyte environment using stagnant electrolyte, flowing electrolyte, and flowing electrolyte at elevated temperature to reveal the different degradation trends in the PEMFC and aqueous environments and to determine the relevance of aqueous measurements to the stability of Pt nanoparticle catalyst in the fuel cell environment. The observed changes in the particle size distributions (PSDs) were analyzed to elucidate the extent and mechanisms of particle growth and corresponding mass and active surface area losses in the different environments. These losses indicate a Pt nanoparticle surface area loss mechanism controlled by Pt dissolution, the particle size dependence of Pt dissolution, the loss of dissolved Pt into the membrane and electrolyte, and, to a lesser extent, the re-deposition of dissolved Pt onto larger particles. Based on the geometric surface area loss, mass loss, and mean particle size increase trends, the aqueous environment best reflecting the fuel cell environment was found to be one in which the electrolyte is flowing rather than stagnant. Pt nanoparticle surface area loss resulting from potential cycling can be inhibited by reducing the number of particles smaller than a critical particle diameter (CPD), which was found to be similar to 3.5 to similar to 4 nm, with the CPD dependent on both the cycling protocol (square wave vs triangle wave) and the catalyst environment (fuel cell, aqueous stagnant, aqueous flowing electrolyte, or elevated temperature flowing electrolyte)

Anomalous small-angle X-ray scattering↗

An electrochemical study of hydrogen in molten 2LiF-BeF 2 (FLiBe) with addition of LiH

The chemical and transport behavior of hydrogen isotopes in molten 2LiF-BeF 2 (FLiBe) is of interest for the design of tritium management systems in nuclear fission and fusion reactors that use FLiBe. The chemical reaction of LiH with FLiBe is used to introduce hydrogen in the molten salt and electrochemical methods are used for in situ studies of hydrogen in FLiBe. LiH reacts with molten FLiBe to generate an electroactive species whose voltammetry peak is proportional to the added quantity of LiH. The cyclic voltammetry reaction potential of 2.009 ± 0.050 V vs Be/Be 2+ and the electron exchange of n = 0.8 ± 0.5 are consistent with the one-electron oxidation of dissolved H in the zero valence state, H o to H + . The concentration of H o is estimated by linear sweep voltammetry at 60–80% of the hydrogen introduced by the reaction of 0.42 mol% LiH with FLiBe and after eleven hours it remains above 40%. It is postulated that covalent BeH 2 is formed in FLiBe upon LiH addition, as a FLiBe-soluble quasi-stable intermediate product. Furthermore, the results provide an evaluation of LiH as a means of introducing dissolved hydrogen in FLiBe, enabling electrochemical methods as tools to advance the understanding of the chemistry of hydrogen isotopes in FLiBe.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Solute- and solvent-based electromotive force cells for activity measurements of electroactive species in molten salts

A novel combination of solute- and solvent-based electrodes was used to determine the activities of NdCl 3 and GdCl 3 in molten LiCI-KCI eutectic using electromotive force measurements across a broad concentration range of dissolved electroactive species. First, an electrochemical cell using solute-based electrodes was used to define the relative activity of each species as a function of concentration and the concentration region in which Henry's law was applicable. Next, the electromotive force between a solute-based electrode with a known NdCl 3 or GdCl 3 concentration and a solvent-based electrode with a known electromotive force was measured. The solvent-based electrode potential was converted to the Lithium Eutectic Electrode (LEE) potential, which allowed the activity of dissolved NdCl 3 and GdCl 3 to be calculated at the concentrations measured using the solute-based electrodes. The described two-cell method uses electromotive force measurements to accurately determine the activity of electroactive species over a wide concentration range and provides a simple approach to closing the knowledge gap of thermochemical properties of molten salts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

1-Butyl-3-methylimidazolium hydrogen sulfate catalyzed in-situ transesterification of Nannochloropsis to fatty acid methyl esters

We report 1-Butyl-3-methylimidazolium hydrogen sulfate ([Bmim][HSO 4 ]) is used as a solvent and an acid catalyst for in-situ extractive transesterification of wet Nannochloropsis with methanol. The reaction is supposed to be a five-step process: (1) wet algae cell wall dissolves in ionic liquid at reaction temperatures; (2) hydrogen ions and sulfate ions release from the ionization of HSO 4 - . The hydrogen ions (H+) act as catalysts for accelerating the reactive extraction of triglyceride from wet Nannochloropsis; (3) hydrogen ions and methanol molecules transfer from bulk to active site of cells without passing through cell wall that is dissolved by ionic liquid; (4) in-situ transesterification of lipid (mainly triglycerides) with methanol; and (5) products transfer from inside of algae cells to outside of cells. The crude biodiesel yield of [Bmim][HSO 4 ] catalyzed in-situ transesterification is about 95.28% at reaction temperature of 200 °C, reaction time of 30 min, mass ratio of [Bmim][HSO4] to wet Nannochloropsis of 0.9:1, and a mass ratio of methanol to wet algae of 3:1. It decreases to 81.23% after [Bmim][HSO 4 ] is recycled for 4 times, which indicates that [Bmim][HSO 4 ] catalyzed in-situ transesterification is an economic approach for biodiesel production from wet algae.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation of enhanced CO 2 storage in deep saline aquifers by WAG and brine extraction in the Minnelusa sandstone, Wyoming

Geological CO 2 sequestration in deep saline aquifers has been extendedly investigated to reach the goal of carbon neutral as large amount of CO 2 can be reduced in a short time. Here, this study investigates the feasibility of water-alternating-gas (WAG) injection and brine extraction on enhancing CO 2 storage in a target deep saline aquifer, Minnelusa Sandstone in the Powder River Basin (PRB) of Wyoming. An integrated numerical model is developed to account for four scenarios: (1) CO 2 continuous injection (CI) through one injection well, (2) WAG injection through one injection well, (3) CO 2 CI through one injection well and brine extraction through one producer, (4) WAG injection through one injection well and brine extraction through one producer. Simulation results suggest that WAG injection and brine extraction corporately make it possible to enhance CO 2 injectivity while securing CO 2 storage safety. For instance, WAG injection considerably reduces structural trapping contribution while enhances dissolved and residual trapping contributions. As for brine extraction, it can decrease the maximum averaged reservoir pressure by 37% and 22% for CI and WAG injection, respectively. Besides, sensitive analyses of the operational parameters for the fourth scenarios are performed. Results reveal that, when the amount of total CO 2 injection has been predetermined, CO 2 injection time and rate within each period of WAG should be small whereas it is preferable to have large water injection time and rate. This is to secure desirable dissolved and residual trapping contributions (store CO 2 with safety). Sensitive degree results confirm that CO 2 injection rate, water injection time, and CO 2 injection time of WAG injection exhibit significant effects on CO 2 storage whereas the impacts of producer bottom-hole pressure (BHP), water injection rate, and CO 2 -water injection time are relatively weaker. This study not only sheds light on achieving double-win goal: enhance CO 2 injectivity and store CO 2 with safety, but also can be a critical reference for other CO 2 storage in deep saline aquifers.

58 GEOSCIENCES↗