Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “confidence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Neutrinos from SN 1987A - Implications for cooling of the nascent neutron star and the mass of the electron antineutrino

Data on neutrinos from SN 1987A are compared here with parameterized models of the neutrino emission using a consistent and straightforward statistical methodology. The empirically measured detector background spectra are included in the analysis, and the data are compared with a much wider variety of neutrino emission models than was explored previously. It is shown that the inferred neutrino emission model parameters are strongly correlated. The analysis confirms that simple models of the neutrino cooling of the nascent neutron star formed by the SN adequately explain the data. The inferred radius and binding energy of the neutron star are in excellent agreement with model calculations based on a wide range of equations of state. The results also raise the upper limit of the electron antineutrino rest mass to roughly 25 eV at the 95 percent confidence level, roughly 1.5-5 times higher than found previously.

Loredo, Thomas J.↗
NASA NTRS1989

Solar flare X-ray polarimeter utilizing a large area thin beryllium scattering disk

A model of a solar flare X-ray polarimeter utilizing a large-area thin beryllium scattering disk was developed using Monte Carlo techniques for several classes of solar flares. The solar-flare polarimeter consists of a 30-cm-diam Be disk of about 1/3 of a scattering length thickness, which is surrounded by a cylindrical detector composed of six segmented panels of NaI scintillators, each coupled to 15 photomultiplier tubes. The instrument is sensitive to X-rays from 10 to 100 keV. For a class-M-2 solar flare observed for 10 sec from a balloon at an altitude of 150,000 ft, the minimum detectable polarization at the 99 percent statistical confidence level was found to be 1-6 percent over the energy range 20-100 keV.

Gotthelf, E.↗
NASA NTRS1990

Atmospheric drag perturbations on the Mars Observer Orbiter

The nominal launch date of the Mars Observer spacecraft is 09 - 16 - 02, with Mars encounter on 08 - 19 - 93 and the mapping orbit established on 12 - 06 - 93. Because this orbit is nearly circular at low altitude (361 km), both gravity and atmospheric drag will dominate the orbital evolution and are also the major error sources. This paper provides: (1) a summary of atmospheric density and errors for the Mars Observer orbit and time frame, (2) an assessment of spacecraft-position errors using current density estimates, and (3) an estimate of atmospheric density modeling improvement directly from the Doppler data acquired during flight operations. With an improved gravity field model, reconstructed spacecraft-position errors are at the level of 0.5 km (1sigma). However, when predicting the spacecraft's position over 14 days, the density error (at the 90-percent confidence level) dominates, yielding a down-track error of almost 70 km. By modeling the mean atmospheric density, this error can be reduced by at least a factor of two.

Esposito, P. B.↗
NASA NTRS1990

Observations of Neptunian rings by Voyager Photopolarimeter Experiment

The Voyager Photopolarimeter Experiment detected the Neptunian rings 1989N1R and possibly 1989N2R. These rings were also photographed by the Voyager imaging cameras in August 1989. The firm detection of 1989N1R has an equivalent depth (the product of the radial width and mean normal optical depth) of 0.77 + or - 0.13 km, while a less certain detection of 1989N2R has an equivalent depth of 0.7 km + or - 0.2 km. Several statistical techniques were used to search for additional material in the Neptune ring system, and none was identified at a high confidence level.

Horn, Linda J.↗
NASA NTRS1991

Verifying X-Radiographs With Computed Tomographs

Nondestructive technique gives added confidence in inspection. Ambiguous indications in radiographic inspections of metal castings checked by computed tomography. Fast and inexpensive conventional x-ray inspection used to make film image of overall casting, and slower, more costly computed tomography used to reinspect relatively few parts of casting presenting possible diffraction patterns or other difficult-to-interpret features. Method effective in resolving ambiguities in radiographs of turbine blades. Provides same information as metallurgical sectioning.

Roy, Jagatjit↗
NASA NTRS1990

Aeroelastic analysis of wings using the Euler equations with a deforming mesh

Modifications to the CFL3D three dimensional unsteady Euler/Navier-Stokes code for the aeroelastic analysis of wings are described. The modifications involve including a deforming mesh capability which can move the mesh to continuously conform to the instantaneous shape of the aeroelastically deforming wing, and including the structural equations of motion for their simultaneous time-integration with the governing flow equations. Calculations were performed using the Euler equations to verify the modifications to the code and as a first step toward aeroelastic analysis using the Navier-Stokes equations. Results are presented for the NACA 0012 airfoil and a 45 deg sweptback wing to demonstrate applications of CFL3D for generalized force computations and aeroelastic analysis. Comparisons are made with published Euler results for the NACA 0012 airfoil and with experimental flutter data for the 45 deg sweptback wing to assess the accuracy of the present capability. These comparisons show good agreement and, thus, the CFL3D code may be used with confidence for aeroelastic analysis of wings.

Robinson, Brian A.↗
NASA NTRS1990

Calculation of Weibull strength parameters, Batdorf flaw density constants and related statistical quantities using PC-CARES

This manual describes the operation and theory of the PC-CARES (Personal Computer-Ceramic Analysis and Reliability Evaluation of Structures) computer program for the IBM PC and compatibles running PC-DOS/MS-DOR OR IBM/MS-OS/2 (version 1.1 or higher) operating systems. The primary purpose of this code is to estimate Weibull material strength parameters, the Batdorf crack density coefficient, and other related statistical quantities. Included in the manual is the description of the calculation of shape and scale parameters of the two-parameter Weibull distribution using the least-squares analysis and maximum likelihood methods for volume- and surface-flaw-induced fracture in ceramics with complete and censored samples. The methods for detecting outliers and for calculating the Kolmogorov-Smirnov and the Anderson-Darling goodness-of-fit statistics and 90 percent confidence bands about the Weibull line, as well as the techniques for calculating the Batdorf flaw-density constants are also described.

Szatmary, Steven A.↗
NASA NTRS1990

A synopsis of Langley Research Center's lidar effort for the 1986 FIRE IFO

The lidar data obtained by the Langley Aircraft Lidar in October 1986 in Wisconsin is being reduced in a transparent, simple fashion and will be published in its reduced form in a NASA Reference Publication (RP). This reduced data will also be submitted to the FIRE data archives. Some of this reduced data will be presented at the FIRE FSET Workshop to acquaint the science team with the data format to be used in the archive and the upcoming catalog contained in the RP. A new method was utilized in Wisconsin for obtain the depolarization ratio of aerosols. This method involves using a half-wave plate to calibrate the lidar under field conditions. The theory behind this technique will be presented at this workshop as well as some of the lidar calibration results. The lidar calibration will be utilized in interpreting some of the dual polarization lidar data obtained during the IFO in Wisconsin. Some of these data are also discussed. A continuous wave laser lab-type lidar simulator was constructed during the previous year. One of the primary reasons for the construction of the simulator was to attempt dual-polarization lidar-like calibrations under laboratory, rather than field conditions. The data collected by this system was used to experimentally check and thus, inspire confidence in the algorithms being used to interpret the lidar data obtained in the field. A computer program which simulates noisy lidar data was used as a part of this effort in order to obtain some feel for the noise in the inversion parameters as a function of noise in the actual measurements. The lidar simulation will be described in addition to presenting some of the lab-generated calibration data.

Alvarez, Jose M.↗
NASA NTRS1989

Numerical aerodynamic simulation of the space shuttle ascent environment

After the STS 51-L accident, an extensive review of the Space Shuttle Orbiter's ascent aerodynamic loads uncovered several questionable areas that required further analysis. The insight gained by comparing the Shuttle ascent CFD numerical simulations, obtained by the NASA Ames Space Shuttle Flow Simulation Group, to the current IVBC-3 aerodynamic loads database was instrumental in resolving uncertainties on the Orbiter payload bay doors and fuselage. Initial confidence in the numerical simulations was gained by comparing them with the limited flight data that had been obtained during the Orbiter Flight Test (OFT) program. Current CFD results exist for Mach numbers 0.6, 0.9, 1.05, 1.55, 2.0, and 2.5. Since the pre STS-1 wind tunnel test program (IA-105) often yields considerable differences when compared to STS-5 flight data, the M(sub infinity) = 1.05 transonic case is the most investigated. The IA308 mated-vehicle hot gas plume wind tunnel test, recently completed at AEDC 16T (transonic) and Lewis (hypersonic), is also used to compare with the computation where applicable.

Slotnick, Jeff P.↗
NASA NTRS1990

Civil space technology initiative

The Civil Space Technology Initiative (CSTI) is a major, focused, space technology program of the Office of Aeronautics, Exploration and Technology (OAET) of NASA. The program was initiated to advance technology beyond basic research in order to expand and enhance system and vehicle capabilities for near-term missions. CSTI takes critical technologies to the point at which a user can confidently incorporate the new or expanded capabilities into relatively near-term, high-priority NASA missions. In particular, the CSTI program emphasizes technologies necessary for reliable and efficient access to and operation in Earth orbit as well as for support of scientific missions from Earth orbit.

Source record↗
NASA NTRS1990

Flight experience with windshear detection

Windshear alerts resulting from the Honeywell Windshear Detection and Guidance System are presented based on data from approximately 248,000 revenue flights at Piedmont Airlines. The data indicate that the detection system provides a significant benefit to the flight crew of the aircraft. In addition, nuisance and false alerts were found to occur at an acceptably low rate to maintain flight crew confidence in the system. Data from a digital flight recorder is also presented which shows the maximum and minimum windshear magnitudes recorded for a representative number of flights in February, 1987. The effect of the boundary layer of a steady state wind is also discussed.

Zweifel, Terry↗
NASA NTRS1990

Flight service evaluation of composite helicopter components

An assessment is presented of ten composite tail rotor spars and four horizontal stabilizers exposed to the effects of in-flight commercial service for up to nine years to establish realistic environmental factors for use in future designs. This evaluation is supported by test results of helicopter components and panels which have been exposed to outdoor environmental effects since 1979. Full scale static and fatigue tests were conducted on graphite/epoxy and Kevlar/epoxy composite components removed from Sikorsky Model S-76 helicopters in commercial operations off the Gulf Coast of Louisiana. Small scale static and fatigue tests were conducted on coupons obtained from panels exposed to outdoor conditions in Stratford, CT and West Palm Beach, Florida. The panel materials and ply configurations were representative of the S-76 components. The results are discussed of moisture analyses and strength tests on both the S-76 components and composite panels after up to nine years of outdoor exposure. Full scale tests performed on the helicopter components did not disclose any significant reductions from the baseline strengths. The results increased confidence in the long term durability of advanced composite materials in helicopter structural applications.

Mardoian, George H.↗
NASA NTRS1990

On the Variability of the Solar Integral Radiation Constituents

The results of spectral analysis of series of observations of the equatorial and polar diameters, as well as of series of satellite observations of the S sub O variations during 1975 to 1987 presented in papers by Laclare (1987), Delache (1988) and Delache et al. (1988) confirm with confidence the presence of an 11-year modulation in the Sun's radiation and diameter, and consequently, in the effective temperature of the photosphere. The same conclusion has been drawn with regard to the 1000th and 320th daily periodicities. In combination with the results of other research, several obvious conclusions can be drawn from the data presented. The 76-year variation in the period from 1967 to 1987 is not revealed in the data of observations; the data of the middle series will doubtless be made more precise after the facsimile from the initial information is obtained. The basic and comparable contributions to the radius variability yield the 11- and 22-year variations. The presence can easily be seen of harmonics with periods of 2 and 4 years; the 4-year period is revealed up to 1979 only, and the 2-year one, after 1980 only. This is possibly due to the combined contribution of the 11- and 22-year variations (to be more precise, 10.8 and 21.2 years) forming a certain mean 16-year periodicity. In this case, the 4- and 2-year variations can be regarded as the 4th and 8th harmonics of such a mean variation. Measurements of the horizontal diameter made at Greenwich Observatory have not lost their significance for the analysis of phenomena on the Sun, since they contain data having precision characteristics conforming to the level of the latest ground-based diameter measurements.

Nikolsky, G. A.↗
NASA NTRS1991

Stirling engine: Available tools for long-life assessment

A review is presented for the durability approaches applicable to long-time life assessment of Stirling engine hot-section components. The crucial elements are experimental techniques for generating long-time materials property data (both monotonic and cyclic flow and failure properties); analytic representations of slow strain rate material stress-strain response characteristics (monotonic and cyclic constitutive relations) at high temperatures and low stresses and strains; analytic creep-fatigue-environmental interaction life prediction methods applicable to long lifetimes at high temperatures and small stresses and strains; and experimental verification of life predictions. Long-lifetime design criteria for materials of interest are woefully lacking. Designing against failures due to creep, creep-rupture, fatigue, environmental attack, and creep-fatigue-environmental interaction will require considerable extrapolation. Viscoplastic constitutive models and time-temperature parameters will have to be calibrated for the hot-section materials of interest. Analysis combined with limited verification testing in a short-time regime will be required to build confidence in long-lifetime durability models.

Halford, Gary R.↗
NASA NTRS1989

AdaNET prototype library administration manual

The functions of the AdaNET Prototype Library of Reusable Software Parts is described. Adopted from the Navy Research Laboratory's Reusability Guidebook (V.5.0), this is a working document, customized for use the the AdaNET Project. Within this document, the term part is used to denote the smallest unit controlled by a library and retrievable from it. A part may have several constituents, which may not be individually tracked. Presented are the types of parts which may be stored in the library and the relationships among those parts; a concept of trust indicators which provide measures of confidence that a user of a previously developed part may reasonably apply to a part for a new application; search and retrieval, configuration management, and communications among those who interact with the AdaNET Prototype Library; and the AdaNET Prototype, described from the perspective of its three major users: the part reuser and retriever, the part submitter, and the librarian and/or administrator.

Hanley, Lionel↗
NASA NTRS1990

Space shuttle redesigned solid rocket motor Certificate of Qualification (COQ) data report

The Space Shuttle Redesigned Solid Rocket Motor (RSRM) Certification Program provides confidence that the RSRM and its components/subsystems meet or exceed Mission Oriented Requirements when manufactured per design requirements and specified/approved processes. Certification is based on documented results of tests, analyses, inspections, similarity, and demonstrations. Evidencing information is provided to certify that each RSRM component/subsystem satisfies design, mission related requirements and objectives.

Duersch, Fred, Jr.↗
NASA NTRS1989

New measurements of the far ultraviolet scattering properties of interstellar dust

An analysis is presented for the spectra of the diffuse ultraviolet background taken during shuttle flight STS-61C (January 1986). Eight regions of the sky were observed for approximately 20 minutes each, using a spectrograph designed specifically to perform measurements of the UV background. The field of view was 3.8 deg x 8 min, with imaging along the slit to confine stellar contamination. The instrument featured a shutter mechanism to measure internal background during flight, a low-scatter holographically ruled diffraction grating, photon counting microchannel plate detectors, through baffling, and a crystal window to further attenuate stray light. The spectra covered the range 1400 to 1850 A and was binned in 50 A bands. The procedure for substracting the contribution of stars too faint to be detected as discrete sources during the observations (in general this represents a small fraction of the total intensity detected except at the longest wavelengths). A radiative transfer model used to interpret the data and set confidence intervals on the relevant parameters is described. It was found that the continuum component of the diffuse ultraviolet background arises primarily from two sources. One source is scattering of starlight by interstellar dust with an albedo of about 12 percent and a relatively isotropic phase function. A second source consists of about 150 photons/cm/sec/ster/A of extragalactic light which is attenuated by the dust in the galaxy. Although emission features possibly associated with molecular H2 are detected in one look direction, fluorescence of H2 is not a major contributor to the diffuse UV background, at least at galactic latitudes greater than -10 degrees.

Hurwitz, Mark↗
NASA NTRS1990

The NASA controls-structures interaction technology program

The interaction between a flexible spacecraft structure and its control system is commonly referred to as controls-structures interaction (CSI). The CSI technology program is developing the capability and confidence to integrate the structure and control system, so as to avoid interactions that cause problems and to exploit interactions to increase spacecraft capability. A NASA program has been initiated to advance CSI technology to a point where it can be used in spacecraft design for future missions. The CSI technology program is a multicenter program utilizing the resources of the NASA Langley Research Center (LaRC), the NASA Marshall Space Flight Center (MSFC), and the NASA Jet Propulsion Laboratory (JPL). The purpose is to describe the current activities, results to date, and future activities of the NASA CSI technology program.

Newsom, Jerry R.↗