Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Tensile fracture of unidirectional B-Al composite.

Fracture studies on unidirectional boron filament/aluminum matrix composite under axial tension were conducted using scanning electron microscopy, microradiography, and an acoustic emission technique. The combination of these analysis techniques has allowed the description and microstructural characterization of a new noncumulative fracture mode which involves filament break propagation. This fracture mode was found to severely limit the tensile strength of the composite, since the initiation of break propagation leads immediately to catastrophic failure at filament stress levels above a critical value. This critical filament stress was found to be 170,000 psi, and it appeared to be independent of filament diameter, number of filament layers, and the type of matrix alloy.

Steele, J. H.↗
NASA NTRS2019

Experimental Investigation of Cement Hydration in Gravity-Free Environment

In this work, cement hydration in terrestrial and microgravity environment was compared. This was for the first time, when the International Space Station was utilized to fully investigate the complex process of cement solidification. Microstructural development of hydrating cement occurs in stages during the hydration reaction and hardening process, which results in elaborate combinations of amorphous and crystalline phases. The morphology, volume fraction, and distribution of these phases ultimately determine the hardened cement’s material properties. Minimizing gravity-driven phenomena, such as thermosolutal convective flow and sedimentation ensures crystal growth strictly by diffusion and a microstructure forms differently from that observed in typical laboratory conditions on Earth. A test matrix was developed that includes samples with various w/c ratio and various compositions; incorporating alite, pure water and cement system, cement with chemical admixtures, as well as commercial products. This paper reports on main changes initially observed in the microstructural development of hydrated pure compound of tricalcium silicate (C3S).

Neves, Juliana↗
NASA NTRS1993

High surface area, low weight composite nickel fiber electrodes

The energy density and power density of light weight aerospace batteries utilizing the nickel oxide electrode are often limited by the microstructures of both the collector and the resulting active deposit in/on the collector. Heretofore, these two microstructures were intimately linked to one another by the materials used to prepare the collector grid as well as the methods and conditions used to deposit the active material. Significant weight and performance advantages were demonstrated by Britton and Reid at NASA-LeRC using FIBREX nickel mats of ca. 28-32 microns diameter. Work in our laboratory investigated the potential performance advantages offered by nickel fiber composite electrodes containing a mixture of fibers as small as 2 microns diameter (Available from Memtec America Corporation). These electrode collectors possess in excess of an order of magnitude more surface area per gram of collector than FIBREX nickel. The increase in surface area of the collector roughly translates into an order of magnitude thinner layer of active material. Performance data and advantages of these thin layer structures are presented. Attributes and limitations of their electrode microstructure to independently control void volume, pore structure of the Ni(OH)2 deposition, and resulting electrical properties are discussed.

Johnson, Bradley A.↗
DOE OSTI2026

Spectro-Microscopic Analysis of Soot Particle Composition and Source Attribution

Ambient soot particles significantly impact Earth’s radiative balance, human health, and atmospheric visibility. Their microstructural properties depend on formation and aging mechanisms, which vary by emission source and atmospheric processes. Hence, accurately identifying sources of soot enhances our understanding of their physicochemical properties and atmospheric implications. This study used a multi-modal approach to characterize and attribute sources of submicron soot particles collected in Israel during new particle formation events, biomass burning episodes, and background atmospheric conditions. Synchrotron-based X-ray microscopy was used to map soot (elemental carbon), organic carbon, and inorganic species. Implemented atomic force microscopy showed highly diverse phase states, with soot consistently exhibiting a solid-like phase. Automated µ-Raman analysis was subsequently performed on ~690 particles, identifying three soot classes based on spectral features corresponding to the "Defect" (D) and "Graphite" (G) bands of soot. We applied two-peak and five-peak fitting approaches to deconvolute the “Defect” peaks (D1, D2, D3, and D4) and G band from average Raman, revealing varying degrees of graphitic order. The degree of graphitic order was determined from metrics such as the D3 peak area, often observed when soot was internally mixed with organic material. Raman spectral features, along with temporal variations in particle classes contributions, suggest that Particle Type 1 corresponds to traffic related soot and Particle Type 2 to less graphitic soot from biomass burning, while Particle Type 3 is associated with more heterogeneous particulate representative of soot-OC mixtures emitted during new particle formation and biomass burning episodes.

Rivera-Adorno, Felipe (ORCID:0000000273557999)↗
DOE OSTI2021

Irradiation effects in tungsten—From surface effects to bulk mechanical properties

Advanced materials such as tungsten fibre-reinforced composites allow to overcome severe weaknesses of the baseline materials for plasma-facing components — copper and tungsten. The effect of the fusion environment on the mechanical properties of these materials, e.g. the embrittlement by neutron irradiation, plays a key role for the development of future fusion reactors. To simulate this effect, high-energy ions are used as a substitute for the displacement damage by neutrons. We propose the use of very fine tungsten wire as a possibility of studying the influence of irradiation damage on the mechanical properties. This is possible as they allow full-depth irradiation of almost the entire volume despite the limited penetration depth of ions. Geometrical size effects are mitigated due to the nanoscale microstructure of the wire. In addition, similar wire is used in tungsten fibre-reinforced composites. Thus, the investigation of irradiated wire can directly be used for the prediction of the bulk composite properties. For the proof of this concept tungsten wire with a diameter of 16 μm was electrochemically thinned to 5 μm and irradiated with 20.5 MeV W 6+ ions. The mechanical properties were subsequently determined by macroscopic tensile testing. Irradiation to 0.3, 1 and 9 dpa did not lead to a change of the mechanical behaviour. Both strength and ductility, the latter indicated by the reduction of area, were similar to the as-fabricated state.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A lightweight Fe–Mn–Al–C austenitic steel with ultra-high strength and ductility fabricated via laser powder bed fusion

Lightweight Fe–Mn–Al–C steels have become a topic of significant interest for the defense and automotive industries. These alloys can maintain high strength and ductility while also reducing weight in structural applications. Conventionally processed Fe–Mn–Al–C austenitic steels with high Al content (~9 wt%) demonstrate greater than 1.5 GPa strength with 35% elongation. Several recent studies have demonstrated success in fabricating steel parts using laser powder bed fusion (L-PBF) additive manufacturing (AM), which can generate near-net-shape components with complex geometries and is capable of local microstructural control. However, studies on L-PBF processing of Fe–Mn–Al–C alloys have focused on low Al content (<5 wt%) compositional regimes representing alloys that undergo transformation-induced plasticity (TRIP) and twinning-induced plasticity (TWIP). Here, in this study, we present the effects of L-PBF processing on the microstructure and mechanical properties of an Fe–30Mn–9Al–1Si-0.5Mo-0.9C austenitic steel. A process optimization framework is employed to determine an ideal L-PBF processing space that will result in >99% density parts. Implementing this framework resulted in near-fully dense specimens fabricated over a broad range of process parameters. Additionally, two bi-directional scan rotation strategies (90° and 67°) were applied to understand their effects on texture and anisotropy in this material. As-printed specimens displayed considerable work-hardening characteristics with average strengths of up to 1.3 GPa and 36% elongation in the build direction. However, solidification microcracks oriented in the build direction resulted in anisotropy in tensile strength and ductility resulting in average strengths of 1.1 GPa and 20% elongation perpendicular to the build direction. The successful L-PBF fabrication of Fe–30Mn–9Al–1Si-0.5Mo-0.9C presented here is expected to open new avenues for weight reduction in structural applications with a high degree of control over part topology.

36 MATERIALS SCIENCE↗
NASA NTRS1973

The effect of thermal cycling on the structure and properties of a Co, Cr, Ni-TaC directionally solidified eutectic composite

A Co, Cr, Ni-TaC directionally solidified eutectic composite was subjected to thermal fatigue between 427-1093°C. The material suffered degradation in microstructure and elevated temperature mechanical properties. The loss in properties varied with the maximum cycling temperature and number of cycles. This behavior is attributed to the increasing solubility of the TaC in the matrix with temperature from 0.4% at room temperature to 2.2% at 1200°C. During the thermal cycling, the TaC is subjected to solution and reprecipitation which form serrations on the fibers since the easy growth planes of the TaC are not coincident with the fiber faces exposed to the matrix.

Composites↗
NASA NTRS2001

Microstructural Investigation of High Emittance Glass Coatings on Fibrous Ceramic Insulation

This viewgraph presentation provides an overview of the Space Shuttle Thermal Protection System (TPS) and the various products incorporated in the TPS. There are three tile systems which include pure silica, fibrous refractory composite insulation (FRCI), and alumina enhanced thermal barrier (AETB). Coating systems include reaction cured glass (RCG) and toughened uni-piece insulation (TUFI). The microstructures of these systems are explored as are the manufacturing processes associated with each. Microstructural investigation using methods such as automated X-ray spectral image analysis (AXSIA) is a crucial part of understanding the mechanical nature of these systems.

Ellerby, Don↗
DOE OSTI2025

Multiscale investigation of thermomechanical and compositional developments in Ni alloy 718 under laser processing

Laser processing has been widely employed in various applications due to its exceptional spatial resolution. However, the rapid temperature gradients generated in localized areas present significant challenges for experimental characterization using conventional instruments. To characterize Ni alloy 718 during laser processing, we employed in-situ synchrotron X-ray diffraction with a high-speed detector, a method particularly well-suited for probing processes with high temporal and spatial resolution. Through a series of in-situ experiments, we investigated the local variations in the evolution of microstructures and thermomechanical behaviors within a keyhole mode melt pool. The in situ macroscopic thermomechanical behaviors were quantified using an empirical model derived from diffraction patterns, with experimental results showing reasonable agreement with finite element analysis. Various laser parameters were tested to assess their influences on the residual strains in the melt pools. The results revealed that the residual strain in the keyhole mode melt pool is relatively insensitive to variations in the parameters and is smaller than that in the melt pool created under conduction mode laser scanning. Additionally, we analyzed the shapes of individual diffraction spots, providing insights into the plastic behaviors and compositional developments in the resolidified alloy. The analysis confirmed that compositional variations in a dendritic microstructure manifest as asymmetric broadening of the diffraction spots.

Ni alloy 718↗
DOE OSTI2021

Strength-promoting mechanism of alkanolamines on limestone-calcined clay cement and the role of sulfate

This paper reports the strength-promoting mechanism of alkanolamines on limestone-calcined clay cement (LC{sup 3}). The hydration kinetics, phase formation and microstructure of LC{sup 3} with triethanolamine (TEA) or triisopropanolamine (TIPA) were investigated. TEA enhanced the strength of LC{sup 3}, while TIPA was effective at 28 days, and a correct sulfate addition promoted their effects. Alkanolamines accelerated the aluminate reaction of LC{sup 3} during early hydration, increased sulfate slowed this reaction by producing more ettringite. TIPA favoured the hydration of ferrite in clinker, not only accelerated the silicate reaction of metakaolin, but also resulted in a rapid limestone reaction. Alkanolamines altered the morphology and chemical composition of the aluminate hydrates and C-A-S-H. Alkanolamines enabled the reduction of porosity of hardened pastes and the increased sulfate further refined them. It was the large pores being induced by TIPA at early ages that were considered to have an adverse impact on the early strength of LC{sup 3}.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and properties of additively manufactured Al–Ce–Mg alloys

Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al–Ce–Mg system, designed as near-eutectic (Al–11Ce–7Mg) and hyper-eutectic (Al–15Ce–9Mg) compositions with respect to the binary L → Al + Al 11 Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

36 MATERIALS SCIENCE↗
NASA NTRS2006

Active Metal Brazing and Characterization of Brazed Joints in Titanium to Carbon-Carbon Composites

The Ti-metal/C-C composite joints were formed by reactive brazing with three commercial brazes, namely, Cu-ABA, TiCuNi, and TiCuSiI. The joint microstructures were examined using optical microscopy and scanning electron microscopy (SEM) coupled with energy dispersive spectrometry (EDS). The results of the microstructure analysis indicate solute redistribution across the joint and possible metallurgical bond formation via interdiffusion, which led to good wetting and spreading. A tube-on-plate tensile test was used to evaluate joint strength of Ti-tube/ C-C composite joints. The load-carrying ability was greatest for the Cu-ABA braze joint structures. This system appeared to have the best braze spreading which resulted in a larger braze/C-C composite bonded area compared to the other two braze materials. Also, joint loadcarrying ability was found to be higher for joint structures where the fiber tows in the outer ply of the C-C composite were aligned perpendicular to the tube axis when compared to the case where fiber tows were aligned parallel to the tube axis.

Singh, M.↗
DOE OSTI2022

Additive Manufacturing of C/C-SiC Ceramic Matrix Composites by Automated Fiber Placement of Continuous Fiber Tow in Polymer with Pyrolysis and Reactive Silicon Melt Infiltration

An additive manufacturing process for fabricating ceramic matrix composites has been developed based on the C/C-SiC system. Automated fiber placement of the continuous carbon fibers in a polyether ether ketone matrix was performed to consolidate the carbon fibers into a printed preform. Pyrolysis was performed to convert the polymer matrix to porous carbon, and then Si was introduced by reactive melt infiltration to convert a portion of the carbon matrix to silicon carbide. The densities and microstructures were characterized after each step during the processing, and the mechanical properties were measured. The C/C-SiC composites exhibited a porosity of 10–20%, characteristic flexural strength of 234.91 MPa, and Weibull modulus of 3.21. The composites displayed toughness via a significant displacement to failure.

36 MATERIALS SCIENCE↗
NASA NTRS2024

Filament Wound Composite Analysis Using the NASA Multiscale Analysis Tool (NASMAT) and Finite Element Analysis

Fiber reinforced composite materials, owing to their tailorable thermomechanical and functional properties, allow one to produce a structure that is stronger, stiffer, and lighter than its metal counterpart while performing the same function, yielding a more efficient structure. This not only allows for the improvement of current technologies like aircraft structures, but also enables new technologies like gaseous hydrogen storage for mobility applications, which are otherwise impractical when manufactured using traditional metals due to weight and space restrictions or material embrittlement. However, the use of composites imposes greater design and manufacturing challenges on an engineer, since they are heterogenous, having a distinct structure across multiple length scale, behave generally anisotropically at the structural level and require complex manufacturing and processing methods. Capturing this complex behavior requires detailed numerical simulations, including the modeling of microstructural features like undulations, voids, and fiber alignment. In this paper, multiple repeating unit cells (RUCs), representing filament wound composites, are developed (via a script provided in the Appendix) and analyzed. The refinement of these RUCs is varied, and the analyses are performed using both the Abaqus finite element software and the NASA Multiscale Analysis Tool (NASMAT). A study is undertaken to compare the predicted effective elastic properties of the wound RUC to a laminate representation of the wound RUC, which neglects the undulations. Additionally, two different sets of periodic boundary conditions (PBCs) have been examined. One approximates the real boundary conditions using a standard approach and the other represents the PBCs exactly through the use of an offset. Lastly, a comparison of the local elastic stress fields is made among the models and approaches. Since wound structures are often approximated as laminated structures, it is important to understand the degree to which this assumption is valid, namely by first comparing the elastic constants and local elastic fields. This will provide, on the one hand, information concerning the bulk mechanical behavior and, on the other hand, insights concerning local load distributions and likely damage initiation sites.

Composites↗
DOE OSTI2023

Rapid Laser Reactive Sintering of Garnet Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 and Li 6.1 La 3 Zr 2 Al 0.3 O 12 and Solid-State Electrolytes

All solid-state lithium-ion batteries (ASSLIBs) have gained significant interest in recent years due to their wide range of applications, including mobile devices, electric vehicles, and grid storage. Garnet-type Li 7 La 3 Zr 2 O 12 (LLZO) solid-state electrolyte (SSE) continues to be a significant player in the fabrication of ASSLIBs with excellent ionic conductivity on the order of 10 -3 S•cm -1 with the integration of dopants and sintering aids to assist conductivity and structural evolution during the sintering procedure. Traditional sintering techniques, such as solid-state sintering (SSS), have been proven to yield desirable crystal structures. However, the low ionic conductivity results from inferior microstructure, and lithium loss is a significant challenge. Recently, a relatively novel sintering process called rapid laser sintering (RLS) has shown great potential for achieving fully dense solid oxide electrolytes with less lithium loss, resulting in high ionic conductivity [1] [2] [3] [4]. Here, we applied a modified RLS method using precursor powders instead of pre-synthesized LLZO powders to fabricate Al-doped LLZO (Li 6.1 La 3 Zr 2 Al 0.3 O 12 + 13 wt% Li 2 CO 3 ) and Ta-doped LLZO (Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 + 5 wt% LiOH•H 2 O) dense electrolytes. This rapid laser reactive sintering (RLRS) could potentially reduce the number of processing steps and therefore lower the manufacturing cost. We hope the rapid high-temperature sintering can densify the electrolyte and avoid the lithium loss for achieving high lithium-ion conductivity. In this work, we optimized a combination of laser parameters (speed and power), initial precursor composition, and controlled atmospheres to discover the optimal conditions for reaching the efficacious crystal structure, microstructure, and ionic conductivity.

25 ENERGY STORAGE↗
DOE OSTI2020

Engineering Multi-scale B2 Precipitation in a Heterogeneous FCC Based Microstructure to Enhance the Mechanical Properties of a Al0.5Co1.5CrFeNi1.5 High Entropy Alloy

While ordered L12 or gamma prime precipitates in face centered cubic (FCC) based microstructures have been extensively used for strengthening Nickel or Cobalt base superalloys, and more recently in high entropy alloys (HEAs) or complex concentrated alloys (CCAs), the possibility of exploiting ordered B2 precipitates in FCC-based systems has been relatively less investigated. The present study shows the propensity of developing a heterogeneous microstructure, consisting of two different distributions of FCC grain sizes, and two different size scales of B2 precipitates, within an FCC-based Al0.5Co1.5CrFeNi1.5 HEA/CCA. This alloy composition has been designed using solution thermodynamics-based modeling such that it has a high phase fraction and solvus temperature of the B2 phase. The resulting heterogenous microstructure exhibited an approximately 400% increase in yield strength with respect to the single-phase FCC solid solution condition of the same alloy while maintaining very good tensile ductility ~20 %.

Dasari, Sriswaroop↗
NASA NTRS1987

Zirconia toughened SiC whisker reinforced alumina composites small business innovation research

The objective of this phase 1 project was to develop a ceramic composite with superior fracture toughness and high strength, based on combining two toughness inducing materials: zirconia for transformation toughening and SiC whiskers for reinforcement, in a controlled microstructure alumina matrix. The controlled matrix microstructure is obtained by controlling the nucleation frequency of the alumina gel with seeds (submicron alpha-alumina). The results demonstrate the technical feasibility of producing superior binary composites (Al2O3-ZrO2) and tertiary composites (Al2O3-ZrO2-SiC). Thirty-two composites were prepared, consolidated, and fracture toughness tested. Statistical analysis of the results showed that: (1) the SiC type is the key statistically significant factor for increased toughness; (2) sol-gel processing with a-alumina seed had a statistically significant effect on increasing toughness of the binary and tertiary composites compared to the corresponding mixed powder processing; and (3) ZrO2 content within the range investigated had a minor effect. Binary composites with an average critical fracture toughness of 6.6MPam sup 1/2, were obtained. Tertiary composites with critical fracture toughness in the range of 9.3 to 10.1 MPam sup 1/2 were obtained. Results indicate that these composites are superior to zirconia toughened alumina and SiC whisker reinforced alumina ceramic composites produced by conventional techniques with similar composition from published data.

Loutfy, R. O.↗
DOE OSTI2021

Experimental and computational analysis of bending fatigue failure in chopped carbon fiber chip reinforced composites

With a better balance among good mechanical performance, high freedom of design, and low material and manufacturing cost, chopped carbon fiber chip reinforced sheet molding compound (SMC) composites show great potential in different engineering applications. Here in this paper, bending fatigue behaviors of SMC composites considering the heterogeneous fiber orientation distributions have been thoroughly investigated utilizing both experimental and computational methods. First, four-point bending fatigue tests are performed with designed SMC composites, and the local modulus is adopted as a metric to represent the local fiber orientation of two opposing sides. Interestingly, SMC composites with and without large discrepancy in local modulus of opposing sides show different fatigue behaviors. Interrupted tests are conducted to explore the bending fatigue failure mechanism, and the damage processes of valid specimens are also closely examined. We find that the fatigue failure of SMC composites under four-point bending is governed by crack propagation instead of crack initiation. Because of this, the heterogeneous local fiber orientations of both sides of the specimen influence fatigue life. The microstructure of the lower side shows a direct influence while that of the upper side also exhibiting influence which becomes more prominent for high cycle fatigue cases. Furthermore, a hybrid micro–macro computational model is proposed to efficiently study the cyclic bending behavior of SMC composites. The region of interest is reconstructed with a modified random sequential absorption algorithm to conserve all the microstructural details including the heterogeneous fiber orientation, while the rest of the regions are modeled as homogenized macro-scale continua. Combined with a framework to capture the progressive fatigue damage under cyclic bending, the bending fatigue behaviors of SMC composites are accurately captured by the hybrid computational model comparing with our experimental analysis.

36 MATERIALS SCIENCE↗