Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Application of sound and temperature to control boundary-layer transition

The growth and decay of a wave packet convecting in a boundary layer over a concave-convex surface and its active control by localized surface heating are studied numerically using direct computations of the Navier-Stokes equations. The resulting sound radiations are computed using linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. It is shown that on the concave portion the amplitude of the wave packet increases and its bandwidth broadens while on the convex portion some of the components in the packet are stabilized. The pressure field decays exponentially away from the surface and then algebraically, exhibiting a decay characteristic of acoustic waves in two dimensions. The far-field acoustic behavior exhibits a super-directivity type of behavior with a beaming downstream. Active control by surface heating is shown to reduce the growth of the wave packet but have little effect on acoustic far field behavior for the cases considered. Active control by sound emanating from the surface of an airfoil in the vicinity of the leading edge is experimentally investigated. The purpose is to control the separated region at high angles of attack. The results show that injection of sound at shedding frequency of the flow is effective in an increase of lift and reduction of drag.

Maestrello, Lucio↗
NASA NTRS1987

Design and fabrication requirements for low noise supersonic/hypersonic wind tunnels

A schematic diagram of the new proposed Supersonic Low Disturbance Tunnel (SLDT) is shown. Large width two dimensional rapid expansion nozzles guarantee wide quiet test cores that are well suited for testing models at large angle of attack and for swept wings. Hence, this type of nozzle will be operated first in the new proposed large scale SLDT. Test results indicate that the surface finish of pilot nozzles is critical. The local roughness Reynolds number criteria R sub k is approx. = 10 will be used to specify allowable roughness on new pilot nozzles and the new proposed tunnel. Experimental data and calculations for M = 3.0, 3.5, and 5.0 nozzles give N-factors from 6 to 10 for transition caused by Goertler vortices. The use of N is approx. = 9.0 for the Goertler instability predicts quiet test cores in the new M = 3.5 and M = 6.0 axisymmetric long pilot nozzles that are 3 to 4 times longer than observed in the test nozzles to date. The new nozzles utilize a region of radial flow which moves the inflection point far downstream and delays the onset and amplification of the Goertler vortices.

Beckwith, Ivan E.↗
NASA NTRS1991

Atomic oxygen interactions with FEP Teflon and silicones on LDEF

The Long Duration Exposure Facility (LDEF) spacecraft represents the first controlled unidirectional exposure of high-fluence atomic oxygen on fluorinated ethylene propylene (FEP Teflon) and silicones. The atomic oxygen erosion yield for FEP Teflon was found to be significantly in excess of previous low fluence orbital data and is an order of magnitude below that of polyimide Kapton. LDEF FEP Teflon erosion yield data as a function of angle of attack is presented. Atomic oxygen interaction with silicon polymers results in crazing of the silicones as well as deposition of dark contaminant oxidation products on adjoining surfaces. Documentation of results and possible mechanistic explanations are presented.

Banks, Bruce A.↗
NASA NTRS1992

Long-term corrosion evaluation of stainless steels in Space Shuttle iodinated resin and water

The effects of stainless steel exposure to iodinated water is a concern in developing the Integrated Water System (IWS) for Space Station Freedom. The IWS has a life requirement of 30 years, but the effects of general and localized corrosion over such a long period have not been determined for the candidate materials. In 1978, Umpqua Research Center immersed stainless steel 316L, 321, and 347 specimens in a solution of deionized water and the Space Shuttle microbial check valve resin. In April 1990, the solution was chemically analyzed to determine the level of corrosion formed, and the surface of each specimen was examined with scanning electron microscopy and metallography to determine the extent of general and pitting corrosion. This examination showed that the attack on the stainless steels was negligible and never penetrated past the first grain boundary layer. Of the three alloys, 316L performed the best; however, all three materials proved to be compatible with an aqueous iodine environment. In addition to the specimens exposed to aqueous iodine, a stainless steel specimen (unspecified alloy) was exposed to moist microbial check valve resin and air for a comparable period. This environment allowed contact of the metal to the resin as well as to the iodine vapor. Since the particular stainless steel alloy was not known, energy dispersive spectroscopy was used to determine that this alloy was stainless steel 301. The intergranular corrosion found on the specimen was limited to the first grain boundary layer.

Krohn, Douglas D.↗
NASA NTRS1990

Atomic oxygen durability of solar concentrator materials for Space Station Freedom

The findings are reviewed of atomic oxygen exposure testing of candidate solar concentrator materials containing SiO2 and Al2O3 protective coatings for use on Space Station Freedom solar dynamic power modules. Both continuous and iterative atomic oxygen exposure tests were conducted. Iterative air plasma ashing resulted in larger specular reflectance decreases and solar absorptance increases than continuous ashing to the same fluence, and appears to provide a more severe environment than the continuous atomic oxygen exposure that would occur in the low Earth orbit environment. First generation concentrator fabrication techniques produced surface defects including scratches, macroscopic bumps, dendritic regions, porosity, haziness, and pin hole defects. Several of these defects appear to be preferential sites for atomic oxygen attack leading to erosive undercutting. Extensive undercutting and flaking of reflective and protective coatings were found to be promoted through an undercutting tearing propagation process. Atomic oxygen erosion processes and effects on optical performance is presented.

Degroh, Kim K.↗
NASA NTRS2005

Traj_opt User's Guide

Trajectory optimization program Traj_opt was developed at Ames Research Center to help assess the potential benefits of ultrahigh temperature ceramic materials applied to reusable space vehicles with sharp noses and wing leading edges. Traj_opt loosely couples the Ames three-degrees-of-freedom trajectory package Traj (see NASA-TM-2004-212847) with the SNOPT optimization package (Stanford University Technical Report SOL 98-1). Traj_opt version January 22, 2003 is covered by this user guide. The program has been applied extensively to entry and ascent abort trajectory calculations for sharp and blunt crew transfer vehicles. The main optimization variables are control points for the angle of attack and bank angle time histories. No propulsion options are provided, but numerous objective functions may be specified and the nonlinear constraints implemented include a distributed surface heating constraint capability. Aero-capture calculations are also treated with an option to minimize orbital eccentricity at apoapsis. Traj_opt runs efficiently on a single processor, using forward or central differences for the gradient calculations. Results may be displayed conveniently with Gnuplot scripts. Control files recommended for five standard reentry and ascent abort trajectories are included along with detailed descriptions of the inputs and outputs.

Saunders, David A.↗
NASA NTRS2012

HEART Aerothermodynamic Analysis

This paper presents an assessment of the aerothermodynamic environment around an 8.3 meter High Energy Atmospheric Reentry Test (HEART) vehicle. This study generated twelve nose shape configurations and compared their responses at the peak heating trajectory point against the baseline nose shape. The heat flux sensitivity to the angle of attack variations are also discussed. The possibility of a two-piece Thermal Protection System (TPS) design at the nose is also considered, as are the surface catalytic affects of the aeroheating environment of such configuration. Based on these analyses, an optimum nose shape is proposed to minimize the surface heating. A recommendation is also made for a two-piece TPS design, for which the surface catalytic uncertainty associated with the jump in heating at the nose-IAD juncture is reduced by a minimum of 93%. In this paper, the aeroshell is assumed to be rigid and the inflatable fluid interaction effect is left for future investigations.

Mazaheri, Alireza↗
NASA NTRS2013

High-Energy Atmospheric Reentry Test Aerothermodynamic Analysis

This paper presents an assessment of the aerothermodynamic environment around an 8.3 meter High Energy Atmospheric Reentry Test (HEART) vehicle. This study generated twelve nose shape configurations and compared their responses at the peak heating trajectory point against the baseline nose shape. The heat flux sensitivity to the angle of attack variations are also discussed. The possibility of a two-piece Thermal Protection System (TPS) design at the nose is also considered, as are the surface catalytic affects of the aeroheating environment of such configuration. Based on these analyses, an optimum nose shape is proposed to minimize the surface heating. A recommendation is also made for a two-piece TPS design, for which the surface catalytic uncertainty associated with the jump in heating at the nose-IAD juncture is reduced by a minimum of 93%. In this paper, the aeroshell is assumed to be rigid and the inflatable fluid interaction effect is left for future investigations

Mazaheri, Alireza↗
NASA NTRS2015

F-16XL Hybrid Reynolds-Averaged Navier-Stokes/Large Eddy Simulation on Unstructured Grids

This study continues the Cranked Arrow Wing Aerodynamics Program, International (CAWAPI) investigation with the FUN3D and USM3D flow solvers. CAWAPI was established to study the F-16XL, because it provides a unique opportunity to fuse fight test, wind tunnel test, and simulation to understand the aerodynamic features of swept wings. The high-lift performance of the cranked-arrow wing planform is critical for recent and past supersonic transport design concepts. Simulations of the low speed high angle of attack Flight Condition 25 are compared: Detached Eddy Simulation (DES), Modi ed Delayed Detached Eddy Simulation (MDDES), and the Spalart-Allmaras (SA) RANS model. Iso- surfaces of Q criterion show the development of coherent primary and secondary vortices on the upper surface of the wing that spiral, burst, and commingle. SA produces higher pressure peaks nearer to the leading-edge of the wing than flight test measurements. Mean DES and MDDES pressures better predict the flight test measurements, especially on the outer wing section. Vorticies and vortex-vortex interaction impact unsteady surface pressures. USM3D showed many sharp tones in volume points spectra near the wing apex with low broadband noise and FUN3D showed more broadband noise with weaker tones. Spectra of the volume points near the outer wing leading-edge was primarily broadband for both codes. Without unsteady flight measurements, the flight pressure environment can not be used to validate the simulations containing tonal or broadband spectra. Mean forces and moment are very similar between FUN3D models and between USM3D models. Spectra of the unsteady forces and moment are broadband with a few sharp peaks for USM3D.

Park, Michael A.↗
NASA NTRS2019

Preliminary Results from an Experimental Assessment of a Natural Laminar Flow Design Method

A 5.2% scale semispan model of the new Common Research Model with Natural Laminar Flow (CRM-NLF) was tested in the National Transonic Facility (NTF) at the NASA Langley Research Center. The model was tested at transonic cruise flight conditions with Reynolds numbers based on mean aerodynamic chord ranging from 10 to 30 million. The goal of the test was to experimentally validate a new design method, referred to as Crossflow Attenuated NLF (CATNLF), which shapes airfoils to have pressure distributions that delay transition on wings with high sweep and Reynolds numbers. Additionally, the test aimed to characterize the NTF laminar flow testing capabilities, as well as establish best practices for laminar flow wind tunnel testing. Preliminary results regarding the first goal of validating the new design method are presented in this paper. Experimental data analyzed in this assessment include surface pressure data and transition images. The surface pressure data acquired during the test agree well with computational fluid dynamics (CFD) results. Transition images at a variety of Reynolds numbers and angles of attack are presented and compared to computational transition predictions. The experimental data are used to assess transition due to a turbulent attachment line, as well as crossflow and Tollmien-Schlichting modal instabilities. Preliminary results suggest the CATNLF design method is successful at delaying transition on wings with high sweep. Initial analysis of the transition front images showed transition Reynolds numbers that exceed historic experimental values at similar sweep angles. , section lift

Lynde, Michelle N.↗
NASA NTRS1994

2-D and 3-D oscillating wing aerodynamics for a range of angles of attack including stall

A comprehensive experimental investigation of the pressure distribution over a semispan wing undergoing pitching motions representative of a helicopter rotor blade was conducted. Testing the wing in the nonrotating condition isolates the three-dimensional (3-D) blade aerodynamic and dynamic stall characteristics from the complications of the rotor blade environment. The test has generated a very complete, detailed, and accurate body of data. These data include static and dynamic pressure distributions, surface flow visualizations, two-dimensional (2-D) airfoil data from the same model and installation, and important supporting blockage and wall pressure distributions. This body of data is sufficiently comprehensive and accurate that it can be used for the validation of rotor blade aerodynamic models over a broad range of the important parameters including 3-D dynamic stall. This data report presents all the cycle-averaged lift, drag, and pitching moment coefficient data versus angle of attack obtained from the instantaneous pressure data for the 3-D wing and the 2-D airfoil. Also presented are examples of the following: cycle-to-cycle variations occurring for incipient or lightly stalled conditions; 3-D surface flow visualizations; supporting blockage and wall pressure distributions; and underlying detailed pressure results.

Piziali, R. A.↗
DOE OSTI2023

Effect of surface oxides on tritium entrance and permeation in FeCrAl alloys for nuclear fuel cladding: a review

Abstract Iron-chromium-aluminum (FeCrAl) alloys are being considered for the cladding of uranium dioxide fuel in light water reactors (LWRs). FeCrAl alloys have good mechanical properties at temperatures of 300 °C and higher, and have superlative resistance to attack by steam at temperatures of up to 1000 °C and higher. A concern has been raised that the use of FeCrAl for cladding would result in a higher content of tritium in the reactor coolant as compared with the current system where the cladding is a zirconium based alloy. This review shows that the flux of tritium from the fuel rod cavities to the coolant across the fuel cladding wall will be greatly reduced by the presence of oxides on the surface of the cladding. The review of current literature and permeation data show that (a) protective oxides are expected to be present on both sides of the FeCrAl cladding, and (b) depending on the characteristics of these oxide layers it is reasonable to expect about two–three orders of magnitude reduction in tritium permeation, relative to the permeation response in clean, unoxidized condition for FeCrAl steels of interest, around 277 °C–377 °C temperatures.

Electrochemistry↗
NASA NTRS1982

Nacelle Aerodynamic and Inertial Loads (NAIL) project

A flight test survey of pressures measured on wing, pylon, and nacelle surfaces and of the operating loads on Boeing 747/Pratt & Whitney JT9D-7A nacelles was made to provide information on airflow patterns surrounding the propulsion system installations and to clarify processes responsible for inservice deterioration of fuel economy. Airloads at takeoff rotation were found to be larger than at any other normal service condition because of the combined effects of high angle of attack and high engine airflow. Inertial loads were smaller than previous estimates indicated. A procedure is given for estimating inlet airloads at low speeds and high angles of attack for any underwing high bypass ratio turbofan installation approximately resembling the one tested. Flight procedure modifications are suggested that may result in better fuel economy retention in service. Pressures were recorded on the core cowls and pylons of both engine installations and on adjacent wing surfaces for use in development of computer codes for analysis of installed propulsion system aerodynamic drag interference effects.

Source record↗
DOE OSTI2020

Microstructure geometry for thermal barrier coatings to mitigate CMAS attack

Thermal barrier coatings and methods to make such coatings present improved resistance to CMAS infiltration. The method for forming a thermal barrier coating includes applying a layer of the thermal barrier coating to a component having a surface, forming a plurality of first channels in the thermal barrier coating, and forming a plurality of second channels in the thermal barrier coating. The first channels extend through a thickness of the thermal barrier coating from an interface with the surface of the component to a free surface opposite the interface. The second channels are disposed between the free surface and the interface and extending lengthwise generally parallel to the free surface of the thermal barrier coating.

Jordan, Eric↗
DOE OSTI2023

Microstructure geometry for thermal barrier coatings to mitigate CMAS attack

Thermal barrier coatings and methods to make such coatings present improved resistance to CMAS infiltration. The method for forming a thermal barrier coating includes applying a layer of the thermal barrier coating to a component having a surface, forming a plurality of first channels in the thermal barrier coating, and forming a plurality of second channels in the thermal barrier coating. The first channels extend through a thickness of the thermal barrier coating from an interface with the surface of the component to a free surface opposite the interface. The second channels are disposed between the free surface and the interface and extending lengthwise generally parallel to the free surface of the thermal barrier coating, wherein the thermal barrier coating comprises a material comprising yttrium aluminum garnet (YAG) or yttria stabilized zirconia (YSZ).

Jordan, Eric↗
NASA NTRS1976

Leeward heat transfer experiments on the shuttle orbiter fuselage

A recent study by Mruk et al. (1975) of convective heat transfer on the leeward surface of a space shuttle orbiter fuselage configuration has yielded experimental data on a fuselage-wing geometry and a bare fuselage (without wings). The present paper summarizes that portion of the investigation related to the bare fuselage tests in which data were obtained for an angle of attack of 90 deg so as to produce nominal planar flow. In addition, some supplementary data were obtained at an angle of attack of 30 deg. The bare fuselage geometry, when immersed in a nearly normal approaching flow, behaves as a cylinder of noncircular cross section and moderate aspect ratio. The data presented were obtained with air as the test gas in a 96-in. hypersonic shock tunnel over a specified range of test conditions. The test program included three values of windward surface temperature and two values of leeward section temperature. Leeward convection is characterized by two values of Stanton number; one for the attached flow just prior to separation and the other for the recirculating zone.

Lamb, J. P.↗
NASA NTRS1975

Effects of geometric variables on the performance of a probe for direct measurement of free-steam stagnation pressure in supersonic flow

An investigation was conducted at Mach numbers of 1.41, 1.83, and 2.20 to determine the effects of parametric variations in the height of the pitot-tube center line from the probe surface and in the radius of the surface curvature on the pressure recovery of a probe designed to measure the free-stream stagnation pressure. The probe consists of a pitot tube mounted on the surface of a curved cylinder of circular cross section. The pitot tube senses the pressure of the stream tube which has been slowed by isentropic compression along the curved surface. Pressure recovery, greater than or equal to 99.8 percent of the free-stream stagnation pressure, was obtained for a wide range both of angle of attack and of yaw for probes satisfying the predetermined optimum design criteria.

Couch, L. M.↗