Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aspect ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Proof test criteria for thin walled pressure vessels

Proof tests were conducted on surface-flaw pressure-vessel specimens of 2219-T87 aluminum base metal and weld metal at three different temperatures: 72, -320, and -423 F, and for three different metal sheet thicknesses: 0.125, 0.250, and 0.375 in. It was found that significant stable crack growth under increasing load can occur prior to failure. Initial flaw shapes and material conditions have a significant effect on the extent of crack growth. Stable crack growth initiates at a lower K sub Ii/K sub cr ratio and is more severe in weld metal specimens than in base metal specimens. Low aspect ratio flaws experience more growth in the depthwise direction than higher aspect ratio flaws. Proof testing assures that any first cycle failure will be by leakage, not by catastrophic failure.

Finger, R. W.↗
NASA NTRS2015

Photopolarimetric Retrievals of Snow Properties

Polarimetric observations of snow surfaces, obtained in the 410-2264 nm range with the Research Scanning Polarimeter onboard the NASA ER-2 high-altitude aircraft, are analyzed and presented. These novel measurements are of interest to the remote sensing community because the overwhelming brightness of snow plagues aerosol and cloud retrievals based on airborne and spaceborne total reflection measurements. The spectral signatures of the polarized reflectance of snow are therefore worthwhile investigating in order to provide guidance for the adaptation of algorithms currently employed for the retrieval of aerosol properties over soil and vegetated surfaces. At the same time, the increased information content of polarimetric measurements allows for a meaningful characterization of the snow medium. In our case, the grains are modeled as hexagonal prisms of variable aspect ratios and microscale roughness, yielding retrievals of the grains' scattering asymmetry parameter, shape and size. The results agree with our previous findings based on a more limited data set, with the majority of retrievals leading to moderately rough crystals of extreme aspect ratios, for each scene corresponding to a single value of the asymmetry parameter.

aspect ratio↗
DOE OSTI2023

Hydrokinetic energy harvesting from slow currents using flow-induced oscillations

To harness marine hydrokinetic energy from slow flows, which constitute the majority of currents, tides, and rivers, new Passive Turbulence Control (PTC), consisting of large turbulence stimulators, is tested experimentally on circular cylinders on springs. Here, this study experimentally investigates the effect of PTC on the onset of Flow-Induced Oscillations (FIO) and particularly the relative onset of Vortex-Induced Vibrations (VIV) and galloping. Experiments are conducted in the Low Turbulence Free Surface Water Channel, University of Michigan. Fixed are: mass ratio m* = 1.48, aspect ratio l/D = 10.29, and total damping ratio ζ = 0.04. Parameters are: cylinder diameter D, spring stiffness K, PTC location and height, and flow speed U$\in$[0.36 m/s-1.45 m/s]. Placing the leading edge of PTC at 40–60° induces high amplitude FIO while placement at 10–20° suppresses FIO. As PTC height increases, VIV and galloping initiate earlier and exhibit higher amplitude with a steeper slope. Lower spring stiffness initiates VIV earlier by reducing the oscillator natural frequency in water. Even though large PTC maintained its effectiveness in initiating galloping early, it has no effect on the earlier initiation of VIV, which starts at a nearly fixed reduced velocity. Lower spring stiffness and large PTC enable power generation at low current speed (0.2 m/s).

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Atmospheric Transport of North African Dust-Bearing Supermicron Freshwater Diatoms to South America: Implications for Iron Transport to the Equatorial North Atlantic Ocean

The equatorial North Atlantic Ocean (NAO) is a nutrient-limited ecosystem that relies on the deposition of long-range transported iron (Fe)-containing aerosols to stimulate primary productivity. Using microscopy, we characterized supermicron and supercoarse mode African aerosols transported to the western NAO in boreal winter/spring. In this work, we detected three particle types including African dust, primary biological aerosol particles, and freshwater diatoms (FDs). FDs contained 4% Fe by weight due to surficial dust inclusions that may be susceptible to chemical processing and dissolution. FDs were typically larger than dust particles and comprised 38% of particles between 10 and 18 μm in diameter. The low density, high surface-area-to-volume ratio, and large aspect ratios of FD particles suggest a mechanism by which they can be carried great distances aloft. These same properties likely increase the residence time of FDs in surface waters thereby increasing the time for Fe dissolution and their potential impact on marine biogeochemical cycles.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Effects of Rolling Reduction on Critical Current Density and Microstructure of Bi-2212 Wires

Bi-2212 Rutherford cables have been fabricated into flat racetrack coils and canted-cosine-theta dipole magnets. The performance gap between the magnets made with Rutherford cables and the “short-sample-limit” is about 30%. To better understand the influence of Rutherford cable processing on the strand performance, we studied three Bi-2212 wires with filament architectures of 37 × 18 and 55 × 18 and diameters of 0.8 and 1.0 mm. To simulate the deformation caused by cabling process, the three wires were rolled with thickness reductions ranging from 10% to 30%. The aspect ratios of rolled strands are between 1.29 and 2.05. The low aspect-ratio wire is also an interesting form for fabricating solenoid coils with higher packing density. The round and rolled strands were heat-treated under 50 bar and with maximum heat treatment temperatures of 885.5 °C and 890.5 °C. The rolling deformation reduced filament size uniformity, resulting in filament merging in fully heat-treated wires. It was found that rolling reduction reduced wire critical current density (JE) by 16 to 18%, but the JE decrease saturated at 15 to 20% of the thickness reduction. It is believed that the reduced JE results from the filament merging caused by rolling and non-uniform shrinking during overpressure heat treatment.

Bi-2212 wire↗
NASA NTRS1976

Theoretical Stability and Control Characteristics of Wings With Various Amounts of Taper and Twist

Stability derivatives have been computed for twisted wings of different planforms that include variations in both the wing taper and the aspect ratio. Taper ratios of 1.0, 0.50, and 0.25 are considered for each of three aspect ratios: 6, 10, and 16. The specific derivatives for which results are given are the rolling moment and the yawing moment derivatives with respect to rolling velocity, yawing velocity, and angle of sideslip. In addition to the stability derivatives, results are included for determining the theoretical rolling moment due to aileron deflection and a series of influence lines is given by which the loading across the span may be determined for any angle-of-attack distribution that may occur on the wing planforms considered.

Henry A Pearson↗
NASA NTRS1986

How different a modern SST would be

The characteristics of a proposed SST are described. The proposed aircraft is to have two engines and an arrow-wing design, a passenger capacity of 250, and attain speeds of Mach 2.7. The low fineness ratio, low-aspect ratio wing planform, different engine nacelles location, and improved lift-to-drag ratio of the aircraft contribute to attaining an economical supersonic cruise. The proposed structural design and materials for the aircraft are examined; the material and design are to be applicable to high Mach and high temperature. Changes in the SST propulsion system, the nozzle designs, and landing and takeoff procedures to improve the operation of the aircraft are discussed.

Driver, C.↗
NASA NTRS1990

Rectangular subsonic jet flow field measurements

Flow field measurements of three subsonic rectangular cold air jets are presented. The three cases had aspect ratios of 1x2, 1x4 at a Mach number of 0.09 and an aspect ratio of 1x2 at a Mach number of 0.9. All measurements were made using a 3-D laser Doppler anemometer system. The data includes the mean velocity vector, all Reynolds stress tensor components, turbulent kinetic energy and velocity correlation coefficients. The data are presented in tabular and graphical form. No analysis of the measured data or comparison to other published data is made.

Morrison, Gerald L.↗
NASA NTRS1955

A Theoretical and Experimental Investigation of the Lift and Drag Characteristics of Hydrofoils at Subcritical and Supercritical Speeds

A theoretical and experimental investigation at subcavitation speeds was made of the effect of the free-water surface and rigid boundaries on the lift and drag of an aspect-ratio-10 hydrofoil at both subcritical and supercritical speeds and of an aspect ratio-4 hydrofoil at supercritical speeds. Approximate theoretical solutions for the effects of the free-water surface and rigid boundaries on drag at subcritical speeds are developed. An approximate theoretical solution for the effects of these boundaries on drag at subcritical speeds is also presented. The agreement between theory and experiment at both supercritical and subcritical speeds is satisfactory for engineering calculations of hydrofoil characteristics from aerodynamic data. The experimental investigation indicated no appreciable effect of the limiting speed of wave propagation on lift-curve slope or angle of zero lift. It also showed that the increase in drag as the critical speed is approached from the supercritical range is gradual. The result is contrary to the abrupt increase at the critical speed predicted by theory.

Wadlin, Kenneth L↗
NASA NTRS1994

Static performance investigation of a skewed-throat multiaxis thrust-vectoring nozzle concept

The static performance of a jet exhaust nozzle which achieves multiaxis thrust vectoring by physically skewing the geometric throat has been characterized in the static test facility of the 16-Foot Transonic Tunnel at NASA Langley Research Center. The nozzle has an asymmetric internal geometry defined by four surfaces: a convergent-divergent upper surface with its ridge perpendicular to the nozzle centerline, a convergent-divergent lower surface with its ridge skewed relative to the nozzle centerline, an outwardly deflected sidewall, and a straight sidewall. The primary goal of the concept is to provide efficient yaw thrust vectoring by forcing the sonic plane (nozzle throat) to form at a yaw angle defined by the skewed ridge of the lower surface contour. A secondary goal is to provide multiaxis thrust vectoring by combining the skewed-throat yaw-vectoring concept with upper and lower pitch flap deflections. The geometric parameters varied in this investigation included lower surface ridge skew angle, nozzle expansion ratio (divergence angle), aspect ratio, pitch flap deflection angle, and sidewall deflection angle. Nozzle pressure ratio was varied from 2 to a high of 11.5 for some configurations. The results of the investigation indicate that efficient, substantial multiaxis thrust vectoring was achieved by the skewed-throat nozzle concept. However, certain control surface deflections destabilized the internal flow field, which resulted in substantial shifts in the position and orientation of the sonic plane and had an adverse effect on thrust-vectoring and weight flow characteristics. By increasing the expansion ratio, the location of the sonic plane was stabilized. The asymmetric design resulted in interdependent pitch and yaw thrust vectoring as well as nonzero thrust-vector angles with undeflected control surfaces. By skewing the ridges of both the upper and lower surface contours, the interdependency between pitch and yaw thrust vectoring may be eliminated and the location of the sonic plane may be further stabilized.

Wing, David J.↗
DOE OSTI2021

Effect of spatial distribution of polymer fibers on preventing spalling of UHPC at high temperatures

Polypropylene (PP) fibers are commonly used for the prevention of thermal spalling of ultra-high performance concrete (UHPC). In this work, the effect of fiber distribution on permeability and spalling resistance is investigated and an analytical model for permeability at 150 °C is proposed. This model, considering the parameters like fiber dimensions, dosage, and percolation, is based on Kozeny-Carman equation. It was found that the percolation of the interconnecting fiber network resulted in a significant increase in permeability of UHPC. X-ray tomography data on the three-dimensional spatial distribution of fibers reiterated that fiber aspect ratio and dosage (and fiber number density) were critical in increasing the fiber connectivity (percolation). It was also found that a vapor permeability of larger than 0.6 × 10{sup −16} m{sup 2} at 150 °C could eliminate spalling. Further, based on a semi-empirical approach, aspect ratio between 300 and 600 was recommended for spalling prevention with a fiber dosage of 0.3–0.4 vol%.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Relation of structure to mechanical properties of thin thoria dispersion strengthened nickel-chromium (TD-NiCr alloy sheet

A study of the relation between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties depend primarily on the grain aspect ratio and sheet thickness. In general, the strength properties increased with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures. A threshold stress for creep appears to exist. Even small amounts of prior creep deformation at elevated temperatures can produce severe creep damage.

Whittenberger, J. D.↗
NASA NTRS1976

Observations on the relationship of structure to the mechanical properties of thin TD-NiCr sheet

A study of the relationship between structure and mechanical properties of thin TD-NiCr sheet indicated that the elevated temperature tensile, stress-rupture, and creep strength properties are dependent on grain aspect ratio and sheet thickness. In general, the strength properties increase with increasing grain aspect ratio and sheet thickness. Tensile testing revealed an absence of ductility at elevated temperatures (not less than 1144 K). Significant creep damage as determined by subsequent tensile testing at room temperature occurs after very small amounts (less than 0.1%) of prior creep deformation over the temperature range 1144-1477 K. A threshold stress for creep appears to exist. Creep exposure below the threshold stress at T not less than 1366 K results in almost full retention of room temperature tensile properties.

Whittenberger, J. D.↗
NASA NTRS1977

Theoretical and experimental analysis of longitudinal and lateral aerodynamic characteristics of skewed wings at subsonic speeds to high angles of attack

The effects of sweep and aspect ratio on the longitudinal and lateral-directional aerodynamic characteristics of low-aspect-ratio skewed (oblique) wings having separation-induced vortex flows along leading and side edges were investigated in the Langley high-speed 7- by 10-foot tunnel at a low-subsonic Mach number. The theoretical analysis used the vortex-lattice method for estimating attached-flow aerodynamic characteristics and the leading-edge suction analogy of Polhamus for estimating separation induced vortex-flow effects. Experimental results were compared with asymmetric, separated, vortex flow theory.

Luckring, J. M.↗
NASA NTRS1978

Interaction of a two-dimensional strip boundary layer with a three-dimensional transonic swept-wing code

A 3D inviscid transonic analysis code was combined with a 2D strip integral boundary layer technique to form an approximate interaction procedure for analyzing the flow over a high aspect ratio wing near cruise conditions. Converged results obtained using the procedure for an aspect ratio 10.3 supercritical wing are discussed. Angle of attack adjustments were made during the iterative procedure in order to compensate for the viscous lift loss. A comparison of the calculations with experimental data is presented.

Newman, P. A.↗
NASA NTRS1931

Large-scale aerodynamic characteristics of airfoils as tested in the variable density wind tunnel

In order to give the large-scale characteristics of a variety of airfoils in a form which will be of maximum value, both for airplane design and for the study of airfoil characteristics, a collection has been made of the results of airfoil tests made at full-scale values of the reynolds number in the variable density wind tunnel of the National Advisory Committee for Aeronautics. They have been corrected for tunnel wall interference and are presented not only in the conventional form but also in a form which facilitates the comparison of airfoils and from which corrections may be easily made to any aspect ratio. An example showing the method of correcting the results to a desired aspect ratio has been given for the convenience of designers. In addition, the data have been analyzed with a view to finding the variation of the aerodynamic characteristics of airfoils with their thickness and camber.

Jacobs, Eastman N↗
NASA NTRS1938

Theoretical stability and control characteristics of wings with various amounts of taper and twist

Stability derivatives have been computed for twisted wings of different plan forms that include variations in both the wing taper and the aspect ratio. Taper ratios of 1.0, 0,50, and 0.25 are considered for each of three aspect ratios: 6, 10, and 16. The specific derivatives for which results are given are the rolling-moment and the yawing-moment derivatives with respect to (a) rolling velocity, (b) yawing velocity, and (c) angle of sideslip. These results are given in such a form that the effect of any initial symmetrical wing twist (such as may be produced by flaps) on the derivatives may easily be taken into account. In addition to the stability derivatives, results are included for determining the theoretical rolling moment due to aileron deflection and a series of influence lines is given by which the loading across the span may be determined for any angle-of-attack distribution that may occur on the wing plan forms considered. The report also includes incidental references to the application of the results.

Pearson, Henry A↗