SEARCH · Engineering Papers

Results for “alloy development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Burst characteristics of advanced accident-tolerant FeCrAl cladding under temperature transient testing

Here assessment of burst characteristics of accident-tolerant fuel (ATF) claddings is essential to evaluate the safety margins of nuclear reactors, and better understanding can enable accelerated licensing for reactor concepts that include the new materials. Therefore, this study investigated the burst behavior of an ATF candidate of C26M, which is an iron–chromium–aluminum alloy (FeCrAl) under transient testing like the simulated loss-of-coolant accident (LOCA) conditions, except the water-quenching phase, in light-water reactors (LWRs). The effect of LOCA specimen length was assessed in terms of post-burst tube parameters. No critical length effect was determined on the burst pressure, burst location, and burst size measurements. Burst temperature showed larger variation likely due to its measurement approach used in this study. The post-test diametral strain was identified as the critical parameter to reduce the specimen length as compared to tube burst length or width. Postmortem optical metrology and digital image correlation were employed to determine the local strain-state during the simulated LOCA, which showed the loading path was close to equibiaxial conditions in regions away from the burst location, rather than internally pressurized conditions (or “plane-strain” tension). Pst-test microstructural characterizations of the FeCrAl revealed that ductile damage was present at the edge of the outer radial surface while the rest of the material was ruptured via cleavage at LOCA burst temperatures. Furthermore, internal grain boundary cracks were observed at locations away from the tube burst region. This behavior was considered to occur during the cooling down period of the simulated LOCA test. Overall, this study aimed to provide essential data for fuel performance code development by considering micromechanics of the deformation and failure.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Effect of Zr and Sc additions on coarsening- and creep resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructure and creep properties are studied in a eutectic AlSi10Mg alloy modified with Zr and Sc additions (Al-9.8Si-0.32Mg-0.70Zr-0.23Sc, wt%) manufactured through laser powder-bed fusion (L-PBF). Three types of Zr/Sc-bearing powders - elemental, master-alloy, and pre-alloyed - are employed in the fabrication process, with the pre-alloyed powders providing the highest incorporation of Zr and Sc in the Al matrix. Here, the as-printed alloy exhibits a fine cellular Al-Si eutectic structure which fragments and coarsens into micron-sized Si particles during aging at 300 ºC, leading to a steady drop in alloy microhardness between 0.1 and 1000 h. Coarsening of the eutectic Si phase during aging is not measurably affected by Zr and Sc in solid solution, which precipitate during aging and increases strength, compensating weakening from Si coarsening between 1 and 200 h at 300 ºC. Atom-probe analysis in the peak-aged condition (96 h/300 °C) confirms the presence of Al 3 (Sc,Zr) secondary nano-precipitates with an average radius of 1.0 nm and some Si solubility. Micron-sized grains are present throughout the alloy, with ultra-fine-grained regions at the melt pool boundaries, neither of which coarsen during long-term aging at 300 ºC. Under creep conditions at 300 °C, the Zr/Sc-bearing alloy with Al 3 (Sc,Zr) nano-precipitates exhibits power-law behavior, with a high apparent stress exponent (n a = 9) and a high threshold stress (σ th = 43 MPa), exhibiting nearly double the strength of a Zr/Sc-free AlSi10Mg control alloy (σ th = 22 MPa).

36 MATERIALS SCIENCE↗

DOE OSTI2024

FY24 progress report on A709 mechanical properties data development and A709 thermal aging status

The report provides the status of the creep, fatigue, and creep-fatigue testing to date conducted at Idaho National Laboratory to generate the data package. This data package evaluates the material performance from three commercial heats to support the Alloy 709 qualification in American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section III, Division 5. First procured heat was manufactured by G.O. Carlson with heat number 58776. Second and third heats were fabricated by ATI Specialty Rolled Products with heat numbers 529900 and 530843, respectively. A series of creep and cyclic specimens were fabricated from these three heats and tests were performed. A list of finished, ongoing, and planned test are presented for creep, fatigue, and creep-fatigue tests. Cyclic properties of three commercial heats are compared.

36 MATERIALS SCIENCE↗

DOE OSTI2025

FY24 progress report on A709 mechanical properties data development and A709 thermal aging status

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Alloying of Mn with Bi‐Rich Surfaces of Bi 2 Te 3 by Topotactic Reaction

Interfacing topological insulators (TI) with magnetic materials enables accessing quantum effects for advanced devices. The synthesis of such heterostructures faces challenges due to interlaying mixing and the often-complex multicomponent materials required to combine the desired properties. An alternative synthesis to direct growth is the modification of 2D materials by topotactic reactions to introduce new functionalities into pre-formed single or few-component 2D sheets. Here, the self-formation of bismuthene (a bilayer of Bi; Bi 2 ) is utilized by thermal decomposition of Bi 2 Te 3 as a platform to create novel 2D overlayers on the TI- substrate. Specifically, the Bi 2 layer is modified by reacting it with vapor deposited Mn in an attempt to induce magnetic properties. Scanning tunneling microscopy indicates that the Mn modified surface remains in a planar 2D layer, indicating the formation of an ordered Mn-rich surface layer. Density functional theory (DFT) is used to develop models of both the Bi-rich Bi 2 Te 3 surface as well as their subsequent Mn-modified structure. The DFT models indicate the possibility of magnetic ordering of the high spin Mn 2+ ions. The successful synthesis of planar MnBi alloys on a van der Waals material illustrates topotactic reactions as an alternative for creating novel layered heterostructures.

2D materials↗

DOE OSTI2024

From phase decomposition to evaporation: A multi-modal evaluation of thermally degraded model lightweight high-entropy alloy

Lightweight high-entropy alloys (LHEAs) have the potential to replace conventional lightweight materials due to their superior mechanical properties and thermal stability. However, the thermal degradation pattern of LHEAs from phase decomposition to evaporation is not clear. We develop a new Al-based dual phase (FCC + HCP) LHEA—AlTi 0.45 CuZn, and further investigate its thermal degradation behavior for potential high-temperature structural applications. Using multimodal advanced characterization techniques such as differential scanning calorimetry/thermogravimetric analysis, scanning/transmission electron microscopy, and synchrotron X-ray diffraction/pair distribution function (XRD/PDF), a sequence of thermal degradation events beyond the thermal phase stability limit—between 250 and 360 °C—is observed. These include phase decomposition at ~360 °C, Zn evaporation at ~750 °C, and LHEA melting at 880 °C which results in ~25% cumulative weight loss. The formation of Al-Ti phase off the AlTi 0.45 CuZn matrix is due to the largest negative mixing enthalpy for Al-Ti than other binary pairs. Similarly, Zn evaporation from AlTi 0.45 CuZn LHEA is due to its faster evaporation rate than other constituent elements. The high-resolution synchrotron XRD and PDF results support the aforementioned observations; in addition, they reveal local atomic arrangements, local strain, and sluggish grain growth in the LHEA. Among other LHEAs of close density range (5.55 ≤ ρ ≤ 5.85 g/cc), the investigated LHEA exhibits outstanding nano-indentation hardness values due to the coupled grain size effect and HCP phase strengthening of the FCC matrix. As the search for LHEAs for lightweight applications grows, this study shows the potential use of AlTi 0.45 CuZn LHEA for structural applications even at elevated temperatures.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Accelerated corrosion testing of cold spray coatings on 304L in chloride environments

Cold spray is an advanced metal manufacturing technique applied across many fields for a wide range of functions. Low heat input and compressive stresses induced into the substrate by the cold spray process makes it a promising choice for protective corrosion resistant coatings. One potential application for cold spray is as a protective coating against corrosion for spent nuclear fuel (SNF) interim dry storage canisters. As these canisters are currently stored at interim storage locations longer than originally intended, chloride induced stress corrosion cracking has been identified as a high priority knowledge gap, specifically with respect to prolonging or extending canister lifetimes ( Teague et al., 2019 ). The high deployability of cold spray, for which nozzles have been developed for application in constrained spaces, in conjunction with beneficial properties inherent to cold spray makes this a good candidate for a corrosion protection coating on SNF canisters. This work explores a pathway to rapidly down-select cold spray coatings for canisters by focusing on the corrosion properties. Specifically, this study examines the corrosion protection abilities of nickel and nickel-based alloy cold spray coatings on 304 L stainless steel in chloride rich environments through electrochemical scans and ferric chloride pitting tests (ASTM G48 Method A). It was shown that the porosity of the coating, the processing gas, material selection, and deformation in the substrate all impact the corrosion behavior of cold spray coatings and are areas where optimization could reduce potential materials degradation, enabling enhanced coatings development.

Karasz, Erin K.↗

DOE OSTI2023

Separation of protactinium from uranium-niobium alloys for 231 Pa– 235 U radiochronometry in nuclear forensic investigations

The isolation and purification of protactinium from uranium materials is essential for 231 Pa– 235 U radiochronometry, but separating Pa from uranium-niobium alloys, a common material in the nuclear fuel cycle, is challenging due to the chemical similarity of Pa and Nb. Here, in this work, we present three resin chromatography separation techniques for isolating Pa from U and Nb which were independently developed by three different laboratories through ad hoc adaptations of standard operating procedures. Our results underscore the need for and value of purification methods suitable for a diversity of uranium-based materials to ensure the operational readiness of nuclear forensics laboratories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Machine learning pipeline to predict defect behavior in metallic alloy systems

The interaction between defect and solute atoms is critical to the thermodynamic and kinetic behavior of metallic alloys under exposure to high-energy radiation, causing irradiation damage in materials. Radiation can generate non-equilibrium concentrations of point defects such as vacancies and interstitials. The excess point defects not only accelerate diffusional processes such as precipitation that cause radiation embrittlement, but also change the pathway of phase transformations, including nucleation processes. Understanding these defect behaviors is complicated by the challenge and complexity of addressing each possible local and discrete distribution of environments and chemical interactions around targeted defects-solute or solute-solute complexes. To resolve the challenge, machine learning regression techniques have emerged as powerful tools that can train and construct an energy model to accurately describe the chemical interactions of solutes and defects. In Fiscal Year 2022, the work focused on the workflow development and demonstration using machine learning regression, density functional theory, cluster expansion, and Monte Carlo simulation to predict the effects of ternary solute elements (e.g., aluminum and molybdenum) and point defects on the Cr-rich $\alpha^{\prime}$ precipitation in multicomponent FeCr model alloys. The computational outcomes include the prediction of the ternary phase diagram, vacancy formation energy for different compositions, and the effect of vacancies on the nucleation of Cr-rich clusters. The simulations predict a pronounced change of Cr solubility in bcc Fe by the addition of Al and the rejection of Al atoms from $\alpha^{\prime}$ precipitates. Additionally, the simulations show the formation of Cr-vacancy clusters as the initial nuclei for stable nucleation and growth of $\alpha^{\prime}$ particles. The results demonstrate important outcomes and applications of using machine learning pipeline to study model or commercial alloys with multicomponent solute species and point defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Technological aspects in blanket design: Effects of micro-alloying and thermo-mechanical treatments of EUROFER97 type steels after neutron irradiation

Presently available data on neutron irradiation damage raise doubts on the feasibility of using EUROFER97 steel for a water-cooled starter blanket in a DEMO reactor, since the ductile-to-brittle transition temperature (DBTT) increases significantly for irradiation temperatures below 350°C. The additional DBTT shift caused by H and He transmutation can only be estimated based on very few results with isotopically tailored EUROFER97 steel. Conservative calculations show that the DBTT of EUROFER97 steel could exceed the operating temperature in water-cooled starter blankets within a relatively short time period. This paper presents results from a EUROfusion funded irradiation campaign that was performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The paper compares ten newly developed reduced activation ferritic-martensitic (RAFM) steels irradiated to a nominal dose of 2.5 dpa at 300°C. The post-irradiation experiments using Small Specimen Test Technology included hardness, tensile, and fracture mechanics tests combined with fractography and microstructure analysis are presented. Results show that micro-alloying EUROFER97-type steels influenced the mechanical properties but a dominating impact on irradiation damage resistance could not be identified. In contrast, specific thermo-mechanical treatments lead to better DBTT behavior. Discussion about irradiation response to heat treatment conditions is also given. Here, despite requiring data also at high dpa values, the results indicate that with these modified materials an increased lifetime and potentially also an increased operating temperature window can be achieved compared to EUROFER97.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Development of Improved A800H Weldments

An abstract is not required/available

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Elevated-temperature cyclic properties of advanced manufactured materials

Microreactor developers at the 2019 GAIN Microreactors workshop expressed a need for advanced manufacturing to fabricate microreactor components. Powder metallurgy (PM) hot isostatic pressing (HIP) is more mature than other advanced manufacturing techniques for the following reasons: 1. a code case exists for Section III, Division 1, Subsection NB components of light water reactors to be manufactured using PM HIP Alloy 316L, and 2. tensile and creep properties have been shown to be equivalent to wrought material for Type 316 stainless steel and Grade 91. Thus, PM HIP is more readily deployable in the near term. Elevated-temperature cyclic properties of PM-HIP materials, however, have not been established. The scope of testing for Code qualification could be significantly reduced compared to a new material for the following reasons: 1. only a limited amount of time consuming creep testing would be required, and 2. testing of fatigue and creep-fatigue behavior could be reduced if it can be demonstrated that the properties are comparable to wrought material. The objective of this work package is to develop an understanding of the relationship of advanced materials processing on the material characteristics as they relate to elevated-temperature component design and construction. This will be achieved by the following: • Elevated-temperature fatigue and creep-fatigue testing of PM HIP and wrought Alloy 316L. • Fracture and microstructural characterization of the PM HIP and wrought Alloy 316L. • Analysis of the elevated-temperature fatigue and creep-fatigue properties of PM HIP Alloy 316L. • Draft a report evaluating the elevated-temperature fatigue and creep-fatigue properties of PM HIP Alloy 316L. • Pursue procurement of Alloy 316H and Grade 91 manufactured using PM HIP. • Initiate scoping studies of the procured Alloy 316H or Grade 91 manufactured using PM HIP contingent upon successful material procurement.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Structure, Morphology, and Photovoltaic Implications of Halide Alloying in Lead-Free Cs 3 Sb 2 Cl x I 9-x 2D-Layered Perovskites

Compositional tuning has been a major driving force behind the excellent optoelectronic properties observed in typical Pb-based perovskites. For lead-free perovskite derivatives, a challenge to understanding the connection between compositional tuning and intrinsic optoelectronic properties, hence a barrier towards boosting their performance, comes from the fact that multiple crystalline substructures can form based on composition, film processing, or both. Especially with lower dimensional (0D, 1D, 2D) substructures, the particular polymorph present in the film can be a greater determinant of optoelectronic properties than the composition itself. Herein, we report a simple method to alloy the halide site in all-inorganic lead-free Cs 3 Sb 2 I 9 films while maintaining a consistent 2D-layered substructure, as a means to independently study the photovoltaic implications of halide substitution. We use a broad suite of spectroscopy and device measurements to identify an optimal stoichiometric substitution of chloride for iodide (~ 8 mol%, measured) that balances both intrinsic and bulk optoelectronic properties to achieve a top power conversion efficiency of 2.2%. This work underscores the importance of controlling substructure while investigating the impacts of compositional tuning for the development of lead-free perovskites, and more broadly validates the approach towards realizing lead-free alternative perovskite solar technologies.

14 SOLAR ENERGY↗

DOE OSTI2021

Welding of Haynes 282 to Steels to Enable Modular Rotors for Advanced Ultra Super-Critical Steam Turbines

Steam turbines for an Advanced Ultra Super Critical (AUSC) fossil fired power plant will operate at temperatures well above those of current commercial steam cycles with inlet temperatures more than 760 C , which is beyond the capabilities of alloy steels presently used for steam turbine applications and requires advanced materials. Large components such as steam turbine rotors may be made of nickel based super alloys such as Haynes 282 (H282). However, monolithic forgings of superalloys in the sizes required for large steam turbines rotors can be prohibitively expensive besides many technical challenges. To minimize cost and alleviate the related technical challenges, superalloy use needs to be limited to locations on the steam turbine rotor where strength and temperature requirements cannot be met by conventional steels. This is possible if nickel-based superalloys can be successfully welded to steels and the related technical challenges - machining parts made of dissimilar welded materials, non-destructive examination of such welds for flaw detection; and, material properties of such hybrid components – are sufficiently addressed. In this technology development project, we successfully welded H282 to plates up to ~ 75 mm (~ 3 inches) to a 3.5NiCrMoV steel of similar thickness. Advanced ultrasonic inspection technique called Phased Array Ultrasonic Testing (PAUT) was employed to examine the dissimilar H282-Steel welds, into which flat bottomed side drilled holes (SDH) of various diameters were introduced, to determine the minimum detectable feature sizes; it was shown that with PAUT SDH of dia. down to 0.5 mm could be detected in the base alloys and SDH with dia. down to 2.4 mm could be detected in the weld metal under multiple orientations successfully. An autonomous machining process monitoring system was developed and demonstrated whereby the forces acting on the cutting tool could be actively monitored as the cutting tool transitioned from H282 to Steel across the weld using which the machining parameters can be potentially altered without interruption to extend tool life. This project successfully achieved its objectives of - i. Developing a welding methodology and viable welding geometries, to successfully join H282 to steel 3.5CrMoNiV steel to enable manufacture of modular steam turbine rotors for AUSC applications (conditions of at least 760 °Celsius and 3,100 psia (pounds per square inch absolute pressure) and evaluate the material properties of the welded specimen. ii. Employ the advanced ultrasonic inspection technique to the dissimilar weld metal joint and determine the minimum detectable feature sizes. iii. Develop effective machining techniques to machine such hybrid structures with online tool force monitoring and effect machine state metrics for optimal results.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2024

Open-air plasma-assisted deposition of organosilicon coating for corrosion protection of AZ91D Mg alloy

As a corrosion barrier layer, open-air plasma-assisted organosilicon coating was applied on AZ91D Mg alloy. Organosilicon-coated AZ91D samples, prepared from two different plasma coating processes, were used for corrosion evaluation based on multistep electrochemical and H 2 collection measurements in 3.5 wt% sodium chloride (NaCl) solution. Some coated AZ91D samples were characterized with and without corrosion exposure in NaCl solution using electron microscopies and X-ray chemical analysis techniques. Further, the results indicate that the organosilicon coatings from open-air plasma processes are effective to delay the initiation of corrosion attack and also reduce the corrosion rate for AZ91D substrate. The corrosion attack was considered to develop after permeation of NaCl solution through the coating layer.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Report on FY 2021 testing in support of integrating Alloy 800H and 2.25Cr-1Mo for EPP analysis

The use of simplified Elastic-Perfectly Plastic (EPP) design methods avoids the complexities and limitations of the elastic analysis approach in evaluating strain limits and creep-fatigue damage for Class A metallic coolant boundary components in ASME Boiler and Pressure Vessel Code, Section III, Division 5, Subsection HB, Subpart B. No stress classification and linearization are required in the EPP methods. Further, the strain limits and creep-fatigue damage evaluation procedures based on elastic analysis results were developed for the reactor operating conditions where uncoupled, rate-independent plasticity and stationary creep can be used to approximate the deformation in the component adequately. But at very high temperatures, the deformation is rate-dependent, and it can only be approximated adequately by unified viscoplastic model. Thus, for example, the elastic analysis approach cannot be used to evaluate strain limits and creep-fatigue damage for Alloy 617 above 650 °C. The EPP methods remove the temperature restriction. They can be used to evaluate strain limits and creep-fatigue damage for the full range of temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

High susceptibility to adiabatic shear banding and high dynamic strength in tungsten heavy alloys with a high-entropy alloy matrix

The susceptibility to adiabatic shear banding (ASB) of tungsten heavy alloys (WHAs) is a key factor to determine their penetration performance for kinetic energy penetrators (KEPs). This work reports a novel WHA with strong susceptibility to ASB that uses a precipitation-hardening high-entropy alloy (HEA) as the binding phase of W particles. The results find that nanoscale L12 precipitates and high dislocation density in the matrix contribute a high dynamic yield strength of ~2300 MPa. Also, a narrow ASB with a width of ~12 μm forms in the novel WHA, which is only 6% of the width of ASB in traditional WHAs like W-NiFe, exhibiting a great susceptibility to ASB. The redissolution of precipitates into the matrix because of temperature rise during shearing could sharply soften the shearing location, which is suggested to be a very important factor of destabilizing mechanism to promote the development of ASB.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Perovskite-Type Solid Solution Nano-Electrocatalysts Enable Simultaneously Enhanced Activity and Stability for Oxygen Evolution

A trade-off between catalytic activity and structural stability generally exists in oxygen evolution electrocatalysis, especially in acidic environment. This dilemma limits the development of higher-performance electrocatalysts that are required by next-generation electrochemical technologies. In this work it is demonstrated that the inverse catalytic activity–structural stability relation can be broken by alloying catalytically inert strontium zirconate with the other catalytically active perovskite, strontium iridate. This strategy results in an alloyed perovskite electrocatalyst with simultaneously improved iridium mass activity and structural stability, by about five times, for the oxygen evolution reaction under acidic conditions. The experimental and theoretical results suggest that the alloying strategy generates multiple positive effects, mainly including the reduction of catalyst size, the decrease of catalyst covalency, and the weakening of surface oxygen-binding ability. The synergistic optimization of bulk and surface properties, as a result, enhances the intrinsic activity and availability of surface iridium sites, whilst significantly inhibiting the surface cation corrosion during electrocatalysis.

36 MATERIALS SCIENCE↗