Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Longitudinal aerodynamic characteristics at Mach 0.60 to 2.86 of a fighter configuration with strut braced wing

An investigation was made to determine the effects on longitudinal aerodynamic characteristics of utilizing struts to brace the wing to allow the wing thickness reduction on the LFAX-8 fighter configuration. Structural and load analysis indicated that the maximum airfoil thickness could be reduced from 4.5 to 3.1 percent with the strut brace concept. Wave drag theory indicated that reducing the wing maximum thickness from 4.5 percent to 3.1 percent would yield a significant reduction in zero-lift wave drag of about 28 percent at the design Mach number of 1.60. Strut arrangements designed and tested included, a single straight strut, a single swept strut, and a set of tandem straight struts. In addition, a wire of approximately the same cross sectional area replaced the single straight strut on one series of runs. The original LFAX-8 with the 4.5-percent-thick wing was retested to serve as a base line for this investigation.

Dollyhigh, S. M.↗
NASA NTRS1996

Structural Performance of a Compressively Loaded Foam-Core Hat-Stiffened Textile Composite Panel

A structurally efficient hat-stiffened panel concept that utilizes a structural foam as a stiffener core material has been designed and developed for aircraft primary structural applications. This stiffener concept is fabricated from textile composite material forms with a resin transfer molding process. This foam-filled hat-stiffener concept is structurally more efficient than most other prismatically stiffened panel configurations in a load range that is typical for both fuselage and wing structures. The panel design is based on woven/stitched and braided graphite-fiber textile preforms, an epoxy resin system, and Rohacell foam core. The structural response of this panel design was evaluated for its buckling and postbuckling behavior with and without low-speed impact damage. The results from single-stiffener and multi-stiffener specimen tests suggest that this structural concept responds to loading as anticipated and has excellent damage tolerance characteristics compared to a similar panel design made from preimpregnated graphite-epoxy tape material.

Ambur, Damodar R.↗
NASA NTRS1993

Aeroelastic airfoil smart spar

Aircraft wings and rotor-blades are subject to undesirable bending and twisting excursions that arise from unsteady aerodynamic forces during high speed flight, abrupt maneuvers, or hard landings. These bending excursions can range in amplitude from wing-tip flutter to failure. A continuous-filament construction 'smart' laminated composite box-beam spar is described which corrects itself when subject to undesirable bending excursions or flutter. The load-bearing spar is constructed so that any tendency for the wing or rotor-blade to bend from its normal position is met by opposite twisting of the spar to restore the wing to its normal position. Experimental and theoretical characterization of these spars was made to evaluate the torsion-flexure coupling associated with symmetric lay-ups. The materials used were uniweave AS-4 graphite and a matrix comprised of Shell 8132 resin and U-40 hardener. Experimental tests were conducted on five spars to determine spar twist and bend as a function of load for 0, 17, 30, 45 and 60 deg fiber angle lay-ups. Symmetric fiber lay-ups do exhibit torsion-flexure couplings. Predictions of the twist and bend versus load were made for different fiber orientations in laminated spars using a spline function structural analysis. The analytical results were compared with experimental results for validation. Excellent correlation between experimental and analytical values was found.

Greenhalgh, Skott↗
NASA NTRS1974

Cyclic-stress analysis of notches for supersonic transport conditions

The feasibility of using the finite element method to account for the effects of cyclic load and temperature on local stresses and strains at a notch was demonstrated. The behavior of a notched titanium panel was studied under variable loads and temperatures representative of flight conditions for the lower wing surface of a Supersonic Transport (SST). The analysis was performed with the use of the BOPACE finite-element computer program which provides capability to determine high temperature and large viscoplastic effects caused by cyclic thermal and mechanical loads. The analysis involves the development of the finite-element model as well as determination of the structural behavior of the notched panel. Results are presented for twelve SST flights comprised of five different load-temperature cycles. The results show the approach is feasible, but material response to cyclic loads, temperatures, and hold times requires improved understanding to allow proper modeling of the material.

Source record↗
NASA NTRS2024

Pull-off Behavior of Stitched Composite T-Joints

T-joints are key structural elements that connect opposing surfaces, thereby providing the load path between flat or curved panels (i.e., upper and lower wing skins) and transverse components (i.e., stiffeners). Due to the low interlaminar strength of polymer matrix composites and their geometrical discontinuities, these joints are vulnerable to pull-off loads. To address these issues, through-thickness reinforcements can be employed to enhance the interlaminar capability of these type of joints. In this study, T-joints were manufactured using through-thickness stitching in dry carbon preforms and cured using the vacuum-assisted resin transfer molding (VARTM) process. Stitched and unstitched T-joints were tested under pull-off loading conditions, and surface strain fields were obtained using a 3D digital image correlation system. The ultimate load, displacement, and absorbed energy of the stitched T-joints were greater than their unstitched counterparts by approximately 16%, 34%, and 58%, respectively. Failure mechanisms were identified by examining fracture surfaces using optical microscopy. Results demonstrate that through-thickness stitching significantly improves the damage tolerance of T-joints, which highlights the effectiveness of stitching to enhance the structural integrity of large aerospace components.

VARTM↗
NASA NTRS1974

Rotorcraft dynamics

The dynamic structural analysis of rotary winged aircraft is reported, considering helicopter vibration and loads.

Source record↗
NASA NTRS1976

Flight loads measurements obtained from calibrated strain-gage bridges mounted externally on the skin of a low-aspect-ratio wing

Flight-test measurements of wingloads (shear, bending moment, and torque) were obtained by means of strain-gage bridges mounted on the exterior surface of a low-aspect-ratio, thin, swept wing which had a structural skin, full-depth honeycomb core, sandwich construction. Details concerning the strain-gage bridges, the calibration procedures used, and the flight-test results are presented along with some pressure measurements and theoretical calculations for comparison purposes.

Eckstrom, C. V.↗
NASA NTRS1985

The computational treatment of supersonic wake flows in INCOREL

Supersonic wake flows are computed in both conical and three-dimensional full potential flows by modeling the wake as a planar cut with a potential discontinuity. Continuity of pressure is satisfied exactly on the wake cut by computing the necessary potential jump at each wake cut grid point. In the conical wake problem, the jump in potential vanishes in the crossflow symmetry plane. Generally, good correlation is achieved for fully three-dimensional wake flows with the planar wake approximation. Matching pressures in the isolated wake flow leads to small variations in the spanwise jump in potential. On the other hand, a small variation in the jump in potential near the wing tip flow can lead to a significant loading in the wake flow if the pressures are not matched.

Siclari, M. J.↗
NASA NTRS1986

Application of mathematical optimization procedures to a structural model of a large finite-element wing

An optimization system is described that consists of the finite-element analysis program known as Engineering Analysis Language (EAL), the CONMIN optimization program, and a piecewise linear analysis. The optimization analysis system (OPTEAL) is used to minimize the mass of a transport wing subject to stress constraints for two static load conditions. The optimization procedure and the optimization analysis system (OPTEAL) are described and the optiomized results with fully stressed design results compared.

Walsh, J. L.↗
NASA NTRS1987

Aerodynamic measurements and thermal tests of a strain-gage balance in a cryogenic wind tunnel

An internal strain-gage balance designed and constructed in Europe for use in cryogenic wind tunnels has been tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel. Part of the evaluation was made at equilibrium balance temperatures and it consisted of comparing the data taken at a tunnel stagnation temperature of 300 K with the data taken at 200 K and 110 K while maintaining either the Reynolds number or the stagnation pressure. A sharp-leading-edge delta-wing model was used to provide the aerodynamic loading for these tests. Results obtained with the balance during the force tests were found to be accurate and repeatable both with and without the use of a convection shield on the balance. An additional part of this investigation involved obtaining data on the transient temperature response of the balance during both normal and rapid changes in the tunnel stagnation temperature. The variation of the temperature with time was measured at three locations on the balance near the physical locations of the strain gages. The use of a convection shield significantly increased the time required for the balance to stabilize at a new temperature during the temperature response tests.

Boyden, Richmond P.↗
NASA NTRS1990

Subsonic and transonic low-Reynolds-number airfoils with reduced pitching moments

A subsonic and a transonic airfoil are presented for application in a high-altitude long-endurance aircraft and a very-high-altitude aircraft, respectively. The subsonic airfoil is designed for a lift coefficient c(l) = 1.4 at a chord Reynolds number Re = 700,000 and a very low Mach number. The transonic airfoil is designed for c(l) = 1.0 at Re = 500,000 and a transonic Mach number M = 0.7. Both airfoils are developed to perform as well or better than previously designed airfoils. However, the present airfoils are developed for a constrained pitching moment to reduce aircraft trim drag and to relieve, to some extent, the torsional loads in the typically high-aspect-ratio wings. The beneficial effects of a cruise flap and of boundary-layer transition control on the off-design performance characteristics are illustrated.

Van Dam, C. P.↗
NASA NTRS1997

Panel Flutter Constraints: Analytic Sensitivities and Approximations Including Planform Shape Design Variables

Analytical sensitivities of panel flutter constraints with respect to panel shape as well as thickness and material properties are derived and numerically tested. Cases of fixed in-plane loads and cases in which in-plane loads are variable (depending on panel and overall wing shape as well as material and sizing design variables) are considered. Accuracy of approximations and range of move limits required are studied in preparation for integration with nonlinear programming/approximation concept aeroelastic design synthesis methodology.

Livne, Eli↗
NASA NTRS2009

Further Development of Ko Displacement Theory for Deformed Shape Predictions of Nonuniform Aerospace Structures

The Ko displacement theory previously formulated for deformed shape predictions of nonuniform beam structures is further developed mathematically. The further-developed displacement equations are expressed explicitly in terms of geometrical parameters of the beam and bending strains at equally spaced strain-sensing stations along the multiplexed fiber-optic sensor line installed on the bottom surface of the beam. The bending strain data can then be input into the displacement equations for calculations of local slopes, deflections, and cross-sectional twist angles for generating the overall deformed shapes of the nonuniform beam. The further-developed displacement theory can also be applied to the deformed shape predictions of nonuniform two-point supported beams, nonuniform panels, nonuniform aircraft wings and fuselages, and so forth. The high degree of accuracy of the further-developed displacement theory for nonuniform beams is validated by finite-element analysis of various nonuniform beam structures. Such structures include tapered tubular beams, depth-tapered unswept and swept wing boxes, width-tapered wing boxes, and double-tapered wing boxes, all under combined bending and torsional loads. The Ko displacement theory, combined with the fiber-optic strain-sensing system, provide a powerful tool for in-flight deformed shape monitoring of unmanned aerospace vehicles by ground-based pilots to maintain safe flights.

Ko, William L.↗
NASA NTRS2012

Design, Analysis and Testing of a PRSEUS Pressure Cube to Investigate Assembly Joints

Due to its potential to significantly increase fuel efficiency, the current focus of NASA's Environmentally Responsible Aviation Program is the hybrid wing body (HWB) aircraft. Due to the complex load condition that exists in HWB structure, as compared to traditional aircraft configurations, light-weight, cost-effective and manufacturable structural concepts are required to enable the HWB. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is one such structural concept. A building block approach for technology development of the PRSEUS concept is being conducted. As part of this approach, a PRSEUS pressure cube was developed as a risk reduction test article to examine a new integral cap joint concept. This paper describes the design, analysis and testing of the PRSEUS pressure cube test article. The pressure cube was required to withstand a 2P, 18.4 psi, overpressure load requirement. The pristine pressure cube was tested to 2.2P with no catastrophic failure. After the addition of barely visible impact damage, the cube was pressure loaded to 48 psi where catastrophic failure occurred, meeting the scale-up requirement. Comparison of pretest and posttest analyses with the cube test response agree well, and indicate that current analysis methods can be used to accurately analyze PRSEUS structure for initial failure response.

Yovanof, Nicolette↗