Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMAL SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Modeling Geologic Waste Repository Systems Below Residual Saturation

The heat generated by high-level radioactive waste can pose numerical and physical challenges to subsurface flow and transport simulators if the liquid water content in a region near the waste package approaches residual saturation due to evaporation. Here, residual saturation is the fraction of the pore space occupied by liquid water when the hydraulic connectivity through a porous medium is lost, preventing the flow of liquid water. While conventional capillary pressure models represent residual saturation using asymptotically large values of capillary pressure, here, residual saturation is effectively modeled as a tortuosity effect alone. Treating the residual fluid as primarily dead-end pores and adsorbed films, relative permeability is independent of capillary pressure below residual saturation. To test this approach, PFLOTRAN is then used to simulate thermal-hydrological conditions resulting from direct disposal of a dual-purpose canister in unsaturated alluvium using both conventional asymptotic and revised, smooth models. Importantly, while the two models have comparable results over 100 000 years, the number of flow steps required is reduced by approximately 94%.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ

Our group has recently developed and studied “finger”-type divertors that are a simplified version of the helium-cooled modular divertor with multiple jets (HEMJ) using coupled computational fluid dynamics and thermal stress simulations. Such a simplified geometry could reduce complexity and cost given the large number of fingers required to cover the total divertor target area. Previous experimental studies for this simplified flat design reported lower heat transfer coefficients and higher pressure drops than the HEMJ, contrary to numerical predictions. Subsequent measurements determined that the original test section had significant dimensional variations in the jet exit holes. A new test section was therefore manufactured and tested in the Georgia Tech (GT) helium loop. The experimental results presented here for this test section at maximum heat flux of 7.1 MW/m 2 are in good agreement with numerical predictions. Correlations developed from these experimental data are extrapolated to predict the maximum heat flux that can be accommodated by the flat design and the coolant pumping power requirements under prototypical conditions. Lastly, numerical simulations are used to estimate the sensitivity of the flat design to geometric variations typical of manufacturing tolerances and variations in the gap width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

METHANE IN THE ATMOSPHERE OF THE TRANSITING HOT NEPTUNE GJ436B?

We present an analysis of seven primary transit observations of the hot Neptune GJ436b at 3.6, 4.5, and 8 {mu}m obtained with the Infrared Array Camera on the Spitzer Space Telescope. After correcting for systematic effects, we fitted the light curves using the Markov Chain Monte Carlo technique. Combining these new data with the EPOXI, Hubble Space Telescope, and ground-based V, I, H, and K{sub s} published observations, the range 0.5-10 {mu}m can be covered. Due to the low level of activity of GJ436, the effect of starspots on the combination of transits at different epochs is negligible at the accuracy of the data set. Representative climate models were calculated by using a three-dimensional, pseudospectral general circulation model with idealized thermal forcing. Simulated transit spectra of GJ436b were generated using line-by-line radiative transfer models including the opacities of the molecular species expected to be present in such a planetary atmosphere. A new, ab-initio-calculated, line list for hot ammonia has been used for the first time. The photometric data observed at multiple wavelengths can be interpreted with methane being the dominant absorption after molecular hydrogen, possibly with minor contributions from ammonia, water, and other molecules. No clear evidence of carbon monoxide and carbon dioxide is found from transit photometry. We discuss this result in the light of a recent paper where photochemical disequilibrium is hypothesized to interpret secondary transit photometric data. We show that the emission photometric data are not incompatible with the presence of abundant methane, but further spectroscopic data are desirable to confirm this scenario.

79 ASTRONOMY AND ASTROPHYSICS↗

Probing the crust of the neutron star in EXO 0748-676

X-ray observations of quiescent X-ray binaries have the potential to provide insight into the structure and the composition of neutron stars. EXO 0748-676 had been actively accreting for over 24 yr before its outburst ceased in late 2008. Subsequent X-ray monitoring revealed a gradual decay of the quiescent thermal emission that can be attributed to cooling of the accretion-heated neutron star crust. In this work, we report on new Chandra and Swift observations that extend the quiescent monitoring to ≅5 yr post-outburst. We find that the neutron star temperature remained at ≅117 eV between 2009 and 2011, but had decreased to ≅110 eV in 2013. This suggests that the crust has not fully cooled yet, which is supported by the lower temperature (≅95 eV) measured ≅4 yr prior to the accretion phase in 1980. Comparing the data to thermal evolution simulations reveals that the apparent lack of cooling between 2009 and 2011 could possibly be a signature of convection driven by phase separation of light and heavy nuclei in the outer layers of the neutron star.

79 ASTRONOMY AND ASTROPHYSICS↗

An AMR capable finite element diffusion solver for ALE hydrocodes [An AMR capable diffusion solver for ALE-AMR]

Here, we present a novel method for the solution of the diffusion equation on a composite AMR mesh. This approach is suitable for including diffusion based physics modules to hydrocodes that support ALE and AMR capabilities. To illustrate, we proffer our implementations of diffusion based radiation transport and heat conduction in a hydrocode called ALE-AMR. Numerical experiments conducted with the diffusion solver and associated physics packages yield 2nd order convergence in the L 2 norm.

42 ENGINEERING↗

Computer simulation of carbonization and graphitization of coal

Abstract This study describes computer simulations of carbonization and graphite formation, including the effects of hydrogen, nitrogen, oxygen, and sulfur. We introduce a novel technique to simulate carbonization, ‘Simulation of Thermal Emission of Atoms and Molecules (STEAM)’, designed to elucidate volatile outgassing and density variations in the intermediate material during carbonization. The investigation analyzes the functional groups that endure through high-temperature carbonization and examines the graphitization processes in carbon-rich materials containing non-carbon impurity elements. The physical, vibrational, and electronic attributes of impure amorphous graphite are analyzed, and the impact of nitrogen on electronic conduction is investigated.

Ugwumadu, C. (ORCID:0000000199207594)↗

Hot and dense matter equation of state probability distributions for astrophysical simulations

We add an ensemble of nuclei to the equation of state for homogeneous nucleonic matter to generate a new set of models suitable for astrophysical simulations of core-collapse supernovae and neutron star mergers. We implement empirical constraints from (i) nuclear mass measurements, (ii) proton-proton scattering phase shifts, and (iii) neutron star observations. Our model is also guided by microscopic many-body theory calculations based on realistic nuclear forces, including the zero-temperature neutron matter equation of state from quantum Monte Carlo simulations and thermal contributions to the free energy from finite-temperature many-body perturbation theory. We ensure that the parameters of our model can be varied while preserving thermodynamic consistency and the connection to experimental or observational data, thus providing a probability distribution of the astrophysical hot and dense matter equation of state. Furthermore, we compare our results with those obtained from other available equations of state. While our probability distributions indeed represent a large number of possible equations of state, we cannot yet claim to have fully explored all of the uncertainties, especially with regard to the structure of nuclei in the hot and dense medium.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Neutron capture cross sections of {sup 74}Ge, {sup 76}Ge, and {sup 75}As at 25 keV

The neutron capture cross sections of {sup 74}Ge, {sup 76}Ge, and {sup 75}As have been measured at the Karlsruhe Van de Graaff accelerator by means of the activation technique. The neutron source reaction {sup 7}Li(p,n){sup 7}Be was used for simulating a thermal energy distribution for kT=25 keV to determine the astrophysically relevant stellar cross sections directly. Based on an extended series of activations, consistent results could be obtained, corresponding to Maxwellian average cross sections at kT=30 keV of 37.6{+-}3.9 mb for {sup 74}Ge, 21.5{+-}1.8 mb for {sup 76}Ge, and 362{+-}19 mb for {sup 75}As. These results are more accurate than previous data and are, therefore, important for resolving previous discrepancies. By extrapolation Maxwellian averaged cross sections were derived for thermal energies from 5 to 100 keV. The implications of these results for the s-process abundances in massive stars and for the background conditions in double {beta} decay experiments are discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

System Size Effects on Gyrokinetic Turbulence

The scaling of turbulence-driven heat transport with system size in magnetically confined plasmas is reexamined using first-principles based numerical simulations. Two very different numerical methods are applied to this problem, in order to resolve a long-standing quantitative disagreement, which may have arisen due to inconsistencies in the geometrical approximation. System size effects are further explored by modifying the width of the strong gradient region at fixed system size. The finite width of the strong gradient region in gyroradius units, rather than the finite overall system size, is found to induce the diffusivity reduction seen in global gyrokinetic simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Energy Gap Closure of Crystalline Molecular Hydrogen with Pressure

Here, we study the gap closure with pressure of crystalline molecular hydrogen. The gaps are obtained from grand-canonical quantum Monte Carlo methods properly extended to quantum and thermal crystals, simulated by coupled electron ion Monte Carlo methods. Nuclear zero point effects cause a large reduction in the gap (~2 eV). Depending on the structure, the fundamental indirect gap closes between 380 and 530 GPa for ideal crystals and 330–380 GPa for quantum crystals. Beyond this pressure the system enters into a bad metal phase where the density of states at the Fermi level increases with pressure up to ~450–500 GPa when the direct gap closes. Our work partially supports the interpretation of recent experiments in high pressure hydrogen.

74 ATOMIC AND MOLECULAR PHYSICS↗

TU-H-BRA-07: Design, Construction, and Installation of An Experimental Beam Line for the Development of MRI-Linac Compatible Electron Accelerator

Purpose: MRI guided radiation therapy (MRIgRT) is a rapidly growing field; however, Linac operation in MRI fringe fields represents an ongoing challenge. We have previously shown in-silico that Linacs could be redesigned to function in the in-line orientation with no magnetic shielding by adopting an RF-gun configuration. Other authors have also published insilico studies of Linac operation in magnetic fields; however to date no experimental validation data is published. This work details the design, construction, and installation of an experimental beam line to validate our in-silico results. Methods: An RF-gun comprising 1.5 accelerating cells and capable of generating electron energies up to 3.2MeV is used. The experimental apparatus was designed to monitor both beam current (toroid current monitor), spot size (two phosphor screens with viewports), and generate peak magnetic fields of at least 1000G (three variable current electromagnetic coils). Thermal FEM simulations were developed to ensure coil temperature remained within 100degC. Other design considerations included beam disposal, vacuum maintenance, radiation shielding, earthquake safety, and machine protection interlocks. Results: The beam line has been designed, built, and installed in a radiation shielded bunker. Water cooling, power supplies, thermo-couples, cameras, and radiation shielding have been successfully connected and tested. Interlock testing, vacuum processing, and RF processing have been successfully completed. The first beam on is expected within weeks. The coil heating simulations show that with care, peak fields of up to 1200G (320G at cathode) can be produced using 40A current, which is well within the fields expected for MRI-Linac systems. The maximum coil temperature at this current was 84degC after 6 minutes. Conclusion: An experimental beam line has been constructed and installed at SLAC in order to experimentally characterise RF gun performance in in-line magnetic fields, validate in-silico design work, and provide the first published experimental data relating to accelerator functionality for MRIgRT.

43 PARTICLE ACCELERATORS↗

Insights into the thermo-hydraulic properties of compacted MX80 bentonite during hydration under elevated temperature

In high-level radioactive waste geological repositories, compacted bentonite undergoes coupled thermo-hydraulic processes due to heat released from a central waste canister and groundwater imbibition from the surrounding host rock. An understanding of these processes is essential for long-term simulations of radionuclide migration and canister corrosion, which requires an understanding of temperature effects on the coupled thermo-hydraulic properties governing these processes. In this study, a tank-scale radial infiltration test was used to investigate water imbibition processes in compacted bentonite under a central heater temperature of 200 °C that simulates high thermal gradients in a repository. Interpretation of this test focuses on evaluation of the liquid water wetting front during hydration and the interpretation of the temperature-dependent transient soil water retention curve (SWRC), thermal conductivity function (TCF), and hydraulic conductivity function (HCF). The SWRC during imbibition follows a temperature-dependent wetting path. Temperature effects on the hydraulic conductivity of bentonite in saturated conditions had the greatest effect on the shape of the HCF, with minimal temperature effects at higher suctions. The transient thermal conductivity data matched well with a new TCF linked with the SWRC shape. Although the bentonite layer was restrained, local deformations during hydration may have affected the shapes of the TCF and HCF.

Engineering↗

adamantine-sim/adamantine

Thermal field simulation of the additive manufacturing process enhanced using data assimilation.

Turcksin, Bruno [Oak Ridge National Lab. (ORNL), O↗

Dynamic Modeling Strategy for Flow Regime Transition in Gas-Liquid Two-Phase Flows

In modeling gas-liquid two-phase flows, the concept of flow regimes has been widely used to characterize the global interfacial structure of the flows. Nearly all constitutive relations that provide closures to the interfacial transfers in two-phase flow models, such as the two-fluid model, are flow regime dependent. Current nuclear reactor safety analysis codes, such as RELAP5, classify flow regimes using flow regime maps or transition criteria that were developed for steady-state, fully-developed flows. As twophase flows are dynamic in nature, it is important to model the flow regime transitions dynamically to more accurately predict the two-phase flows. The present work aims to develop a dynamic modeling strategy to determine flow regimes in gas-liquid two-phase flows through introduction of interfacial area transport equations (IATEs) within the framework of a two-fluid model. The IATE is a transport equation that models the interfacial area concentration by considering the creation of the interfacial area, fluid particle (bubble or liquid droplet) disintegration, boiling and evaporation, and the destruction of the interfacial area, fluid particle coalescence and condensation. For flow regimes beyond bubbly flows, a two-group IATE has been proposed, in which bubbles are divided into two groups based on their size and shapes, namely group-1 and group-2 bubbles. A preliminary approach to dynamically identify the flow regimes is discussed, in which discriminator s are based on the predicted information, such as the void fraction and interfacial area concentration. The flow regime predicted with this method shows good agreement with the experimental observations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

CFD Analysis and Design of Detailed Target Configurations for an Accelerator-Driven Subcritical System

High-fidelity analysis has been utilized in the design of beam target options for an accelerator driven subcritical system. Designs featuring stacks of plates with square cross section have been investigated for both tungsten and uranium target materials. The presented work includes the first thermal-hydraulic simulations of the full, detailed target geometry. The innovative target cooling manifold design features many regions with complex flow features, including 90 bends and merging jets, which necessitate three-dimensional fluid simulations. These were performed using the commercial computational fluid dynamics code STAR-CCM+. Conjugate heat transfer was modeled between the plates, cladding, manifold structure, and fluid. Steady-state simulations were performed but lacked good residual convergence. Unsteady simulations were then performed, which converged well and demonstrated that flow instability existed in the lower portion of the manifold. It was established that the flow instability had little effect on the peak plate temperatures, which were well below the melting point. The estimated plate surface temperatures and target region pressure were shown to provide sufficient margin to subcooled boiling for standard operating conditions. This demonstrated the safety of both potential target configurations during normal operation.

43 PARTICLE ACCELERATORS↗

Preliminary Design Evaluation of a Natural Circulation Molten Salt Irradiation Loop

Many promising Molten Salt Reactor (MSR) concepts under development rely on relatively untested salt compositions. Some level of irradiation data will likely be necessary for the licensing of these concepts. A feasibility study is currently underway at Idaho National Laboratory to establish the possibility of hosting a compact molten salt irradiation loop inside the Advanced Test Reactor (ATR). A case study for a uranium-fueled chloride-based salt will be provided in this paper. Neutronic tools are used to obtain flux levels inside of a specific position inside the ATR. Thermal hydraulic simulations are then conducted to scope the achievable natural circulating velocities and inform design decisions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Hydrology controls thermokarst and alters carbon cycling and methane emissions in peatlands near the southern limit of permafrost: Model Inputs and Outputs

This dataset contains model inputs and simulation outputs associated with the study “Hydrology controls thermokarst and alters carbon cycling and methane emissions in peatlands near the southern limit of permafrost.” The ecosys model was extended to represent thermokarst processes in laterally coupled two-dimensional transects and applied to the Scotty Creek basin (Northwest Territories, Canada). The ecosys model and documentation is available for download at https://github.com/jinyun1tang/ECOSYS. The dataset contains the inputs used to run the model for this study (meteorological forcing data (1950–2018) and site-specific soil and vegetation parameters) and model outputs used to generate Figure 3 and Figure 4 in the paper (simulated ground thermal and hydrologic states, vegetation dynamics, and carbon fluxes).

54 ENVIRONMENTAL SCIENCES↗

FY 2008 Annual Progress Report for Advanced Vehicle Technology Analysis and Evaluation Activities and Heavy Vehicle Systems Optimization Program

AVTAE provides an overarching vehicle systems perspective in support of the technology R&D activities of DOE’s VT and Hydrogen, Fuel Cells & Infrastructure Technologies (HFCIT) Programs. AVTAE uses analytical and empirical tools to model and simulate potential vehicle systems, validate component performance in a systems context, verify and benchmark emerging technology, and validate computer models. Hardware-in-theloop testing allows components to be controlled in an emulated vehicle environment. Laboratory testing then provides measurement of progress toward VT technical goals and eventual validation of DOE-sponsored technologies at the Advanced Powertrain Research Facility for light- and medium-duty vehicles and at the ReFUEL Facility for heavy-duty vehicles. For this sub-program to be successful, extensive collaboration with the technology development activities within the VT and HFCIT Programs is required for both analysis and testing.

33 ADVANCED PROPULSION SYSTEMS↗