Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Substrate Specificity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Workshop on Heteroepitaxial InP Solar Cells

In a generic sense, the justification for any sort of InP solar cell research applies, i.e. to take advantage of the inherently high radiation resistance and efficiency of InP solar cells. To be more specific, the approach is justified by its potential for significant cost reduction and the availability of greatly increased cell area afforded by substrates such as Si and Ge. The use of substrates, such as the latter two, would result in increased ruggedness, ease of handling, and improved manufacturability. The use of more rugged substrates would lead to a greatly increased capability for cell thinning leading to the desirable feature of reduced array weight.

Weinberg, I.↗

MOVPE of GaSb/InGaAsSb Multilayers and Fabrication of Dual Band Photodetectors

Metalorganic vapor phase epitaxy (MOVPE) of GaSb/InGaAsSb multilayer thin films and fabrication of bias-selectable dual band photodetectors are reported. For the dual band photodetectors the short wavelength detector, or the upper p- GaSb/n-GaSb junction photodiode, is placed optically ahead of the long wavelength one, or the lower photodiode. The latter is based on latticed-matched In0.13Ga0.87As0.11Sb0.89 with bandgap near 0.6 eV. Specifically, high quality multilayer thin films are grown sequentially from top to bottom as p+-GaSb/p-GaSb/n-GaSb/n-InGaAsSb/p-InGaAsSb/p-GaSb on undoped p-type GaSb substrate, and as n-GaSb/p-GaSb/p-InGaAsSb/n-InGaAsSb/n-GaSb on Te-doped n-type GaSb substrate respectively. The multilayer thin films are characterized by optical microscope, atomic force microscope (AFM), electron microprobe analyses etc. The photodiode mesa steps are patterned by photolithography with wet chemical etching and the front metallization is carried out by e-beam evaporation with Pd/Ge/Au/Ti/Au to give ohmic contact on both n- and p-type Sb based layer surfaces. Dark I-V measurements show typical diode behavior for both the upper and lower photodiodes. The photoresponsivity measurements indicate that both the upper and lower photodiodes can sense the infrared illumination corresponding to their cutoff wavelengths respectively, comparable with the simulation results. More work is underway to bring the long wavelength band to the medium infrared wavelength region near 4 micrometers.

Xiao, Ye-Gao↗

A Dual-Band Dual-Polarized Array for Spaceborne SAR

Future synthetic aperture radar antennas will be significantly more sophisticated than their earlier counterparts, requiring enhanced electrical capabilities such as operation at multiple frequencies with multiple polarization ability, as well as desirable non-electrical features such as light weight, easy and reliable deployability, and low cost. The present paper describes the results of a prototype SAR array developed with these considerations in mind. This paper will describe the development of a dual-frequency array operating at L and C bands, with dual linear polarization capability at both bands. Unlike most earlier dual-band arrays, this array shares the same radiating aperture for both bands and both polarizations, resulting the smallest possible aperture area for a given gain specification. A critical constraint in this project was a requirement for an extremely light weight package, leading to the use of foam substrates with thin dielectric membranes for metalizations of the radiating elements and feed networks.

Pozar, David M.↗

Wireless Open-Circuit In-Plane Strain and Displacement Sensor Requiring No Electrical Connections

A wireless in-plane strain and displacement sensor includes an electrical conductor fixedly coupled to a substrate subject to strain conditions. The electrical conductor is shaped between its ends for storage of an electric field and a magnetic field, and remains electrically unconnected to define an unconnected open-circuit having inductance and capacitance. In the presence of a time-varying magnetic field, the electrical conductor so-shaped resonates to generate harmonic electric and magnetic field responses. The sensor also includes at least one electrically unconnected electrode having an end and a free portion extending from the end thereof. The end of each electrode is fixedly coupled to the substrate and the free portion thereof remains unencumbered and spaced apart from a portion of the electrical conductor so-shaped. More specifically, at least some of the free portion is disposed at a location lying within the magnetic field response generated by the electrical conductor. A motion guidance structure is slidingly engaged with each electrode's free portion in order to maintain each free portion parallel to the electrical conductor so-shaped.

Woodard, Stanley E.↗

NASA Weather Balloon Demonstration of an Additively Manufactured Antenna

Additive manufacturing (AM) enables low-cost, lightweight, and geometrically flexible antennas for rapid deployment missions. This work reports a left-hand circularly polarized magneto-electric dipole printed on a Radix dielectric with inkjet silver metallization and demonstrated as a process replacement for NASA weather-balloon RF hardware. By combining substrate fabrication and metallization, AM provides value for unrecoverable or field-replaceable systems. A physics based verification workflow links AM-specific material behavior to electromagnetic performance and yields bounded total, radiation, and mismatch efficiencies. Standard surface-impedance and roughness models failed to reproduce the frequency-dependent radiation loss observed in printed inks, underscoring the need for AM-specific conductor parameterization. Mission testing confirmed TDRSS link closure from NASA’s Columbia Scientific Balloon Facility and validated a repeatable print–measure–fly workflow for bounding RF performance and qualifying AM antennas for field use.

Peter Moschetti↗

NASA Weather Balloon Demonstration of an Additively Manufactured Antenna

Additive manufacturing (AM) enables low-cost, lightweight, and geometrically flexible antennas for rapid deployment missions. This work reports a left-hand circularly polarized magneto-electric dipole printed on a Radix dielectric with inkjet silver metallization and demonstrated as a process replacement for NASA weather-balloon RF hardware. By combining substrate fabrication and metallization, AM provides value for unrecoverable or field-replaceable systems. A physics based verification workflow links AM-specific material behavior to electromagnetic performance and yields bounded total, radiation, and mismatch efficiencies. Standard surface-impedance and roughness models failed to reproduce the frequency-dependent radiation loss observed in printed inks, underscoring the need for AM-specific conductor parameterization. Mission testing confirmed TDRSS link closure from NASA’s Columbia Scientific Balloon Facility and validated a repeatable print–measure–fly workflow for bounding RF performance and qualifying AM antennas for field use.

Peter Moschetti↗

Acoustic signal investigation in the ice melting under high-power laser irradiation at a wavelength of 2940 nm

We have measured acoustic signals emerging in the melting of a thin (about 2 μm) ice layer, which is sandwiched between two substrates, under high-power laser irradiation at a wavelength of 2940 nm. A negative-pressure acoustic signal arising from the difference in the specific volumes of water and ice was found to occur in the ice melting. The amplitude of this signal was comparable to the amplitude of the positive-pressure signal produced under laser irradiation of the same layer of water. The shapes of acoustic signals were measured for different energy densities of the incident radiation. The variation of negative-pressure pulse shape with increasing radiation energy density was interpreted as a continuity break of the medium. The temperature and pressure in the layer were estimated in the heating of water and the melting of ice. (interaction of laser radiation with matter)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sources of and Remedies for Removing Unwanted Reflections in Millimeter Wave Images of Complex SOFI-Covered Structures

In the recent years, continuous-wave (CW) near-field and lens-focused millimeter wave imaging systems have been effectively. used to demonstrate their utility for producing high-resolution images of metallic structures covered with spray on foam insulation (SOFI) such as the space shuttle external tank. These systems have produced images with a spatial resolution of approximately 2 mm at a frequency of 150 GHz, and can easily interrogate thin as well as thick SOFI (> 9") enabling detection and evaluation of flaws such as voids, disbands, delaminations and corrosion. These systems are relatively simple, inexpensive, easy-to-use, require little to no signal processing of the raw data, on-site friendly, real-time and small. However, for some specific structures a certain interference pattern may be superimposed on the produced images. Generally, this occurs when the SOFI surface is at a relatively significant angle with respect to the surface of the substrate (or other sub-structures) on which it is sprayed. Consequently, the reflection from the surface of the SOFI and that from the substrate (or sub-structure) coherently combine into an interference pattern as the SOFI surface is scanned. There are methods by which the influence of this unwanted interference can be reduced, such as the incorporation of an incidence angle and the proper use of signal polarization. This paper presents the basics of this problem and describes the use of the methods for reducing this unwanted influence through several specific examples. A discussion on how the use of a swept-frequency or pulsed method may also alleviate this problem is also presented.

Khakovsky, S.↗

3D Printed Substrate

In preparation for long-term, manned, deep space missions, NASA requires a sustainable system for crop and food production. This system has a variety of benefits, including a fresh food supply, improvements in air quality, a lower need to resupply and psychological benefits for the gardeners. Specifically, NASA is attempting to improve and iterate their Vegetable Production System (VEGGIE), a plant growth unit currently aboard the International Space Station (ISS). The VEGGIE unit is highly dependent on a variety of factors, including passive water delivery, growth lights, rooting pillows and cabin conditions. While previous teams have improved and redesigned water reservoirs, the primary objective of the project was to create a new substrate unit to replace the current rooting pillow design. The current design consists of an electrostatic bag filled with arcillite and a slow-release fertilizer pellet. The prototype design retains the fertilizer pellet for nutrient consistency, however the outer bag and arcillite fillings have been replaced with a 3D printed lattice block. This lattice block has several key points that allow it to function in similar ways to the current design: 1. The lattice planes are porous, with each pore offset such that the overall porosity is the same as the arcillite filling. 2. The block demonstrates a wicking nature and is able to pull water upwards towards the roots. This minimizes time needed to integrate with the existing water reservoir. 3. The filament used is highly flexible and is able to pull apart to accommodate root growth. 4. The lattice planes are connected by microfibers left behind from the printing process. These fibers provide support for the growing roots and keep the lattice planes properly aligned. The substrate block design seeks to reduce the payload costs by being entirely 3D printed. While filament would still need to be provided to the ISS, it is far less expensive than shipping arcillite due to the significantly lower weight. The final design has iterated the lattice plane concept and utilizes vertically placed planes with pores running parallel to the water reservoir. This design has reliably shown water uptake and retention and has been successful in growing multiple romaine lettuce plants. Future work should include further growth testing using multiple plant species, compost and reusability testing, food safety testing and microgravity growth testing.

Affan Bhutta↗

Copper Electrode on Flexible Substrate by Intense Pulsed Light Sintering of Microsized Copper Particles

Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.

14 SOLAR ENERGY↗

Commentary: Duckweeds as model organisms for metabolic studies

Duckweeds have many practical applications, for example in human nutrition, as animal feed, in the production of bioplastics or vaccines, and phytoremediation (Acosta et al., 2021). Under most conditions, they reproduce asexually which provides genetically uniform material with predictable patterns of growth that make them ideal as sentinel organisms for phytotoxicity testing (Park et al., 2021). Asexual growth also results in high biomass production which makes duckweeds promising candidates as biofuel feedstocks (Acosta et al., 2021; Liang et al., 2023). In addition, duckweed species like Lemna minor and Spirodela polyrhiza are also reemerging as model organisms in plant biology as high-quality full genome assemblies and other genomic resources become available (Chang et al., 2016; Acosta et al., 2021). We argue that duckweed species are particularly of interest for the study of primary plant metabolism. Primary metabolism concerns the part of metabolism that is directly involved in the growth and development of plants, and which tends to be highly conserved among plant species. What makes duckweeds particularly attractive is that when grown on liquid media more precise control of physiological conditions can be attained relative to growth of plants in soil. Also, due to their relatively simple anatomical structure and asexual reproduction of fronds by budding, precise characterization of the physiological state under study is possible through one simple metric, i.e., the specific growth rate (rate of dry weight increase per existing dry weight), which can be incorporated relatively easily into metabolic models. This is not possible for land plants, such as Arabidopsis, because over the course of their life cycle, they go through multiple growth stages and phases of anatomical differentiation, which are much more complex to quantify. Furthermore, duckweeds can grow on organic substrates under heterotrophic or photomixotrophic conditions that facilitate isotope tracer studies. For example, in a previous study on duckweed by one of the authors, Lemna gibba (L). was grown on glucose with a position-specific 13 C-label that can be detected and resolved by Mass Spectrometry or Nuclear Magnetic Resonance spectrometry. Using this approach, the 13 C-label was traced into biomass compounds formed from glucose, particularly isoprenoid compounds. Some of the resulting labeling patterns were in apparent disagreement with predictions based on known metabolic pathways for the biosynthesis of isopentenyl pyrophosphate, the universal building block for isoprenoids, (Lichtenthaler et al., 1997). From this data it was deduced that isoprenoid compounds such as carotenoids and isoprenoid chains of phytol and plastoquinone, synthesized in the chloroplast, are produced via a previously unreported plant metabolic pathway, now known as the methylerythitol/deoxyxylulose-5-phosphate pathway (Lichtenthaler et al., 1997).

59 BASIC BIOLOGICAL SCIENCES↗

Coexistence of epitaxial lattice rotation and twinning tilt induced by surface symmetry mismatch

Combined x-ray diffraction and first-principles studies of various epitaxial rutile-type metal dioxide films on Al{sub 2}O{sub 3}(0001) substrates reveal an unexpected rectangle-on-parallelogram heteroepitaxy. Unique matching of particular lattice spacings and crystal angles between the oxygen sublattices of Al{sub 2}O{sub 3}(0001) and the film(100) result in coexisted crystal rotation and lattice twinning inside the film. We demonstrate that, besides symmetry and lattice mismatch, angular mismatch along a specific crystal direction is also an important factor determining epitaxy. A generalized theorem has been proposed to explain epitaxial behaviors for tetragonal metal dioxides on Al{sub 2}O{sub 3}(0001).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Micro-scale heterogeneity of soil phosphorus depends on soil substrate and depth

Soils comprise various heterogeneously distributed pools of lithogenic, free organic, occluded, adsorbed, and precipitated phosphorus (P) forms, which differ depending on soil forming factors. Small-scale heterogeneity of element distributions recently has received increased attention in soil science due to its influence on soil functions and soil fertility. We investigated the micro-scale distribution of total P and different specific P binding forms in aggregates taken from a high-P clay-rich soil and a low-P sandy soil by combining advanced spectrometric and spectroscopic techniques to introduce new insights on P accessibility and availability in soils. Here we show that soil substrate and soil depth determine micro-scale P heterogeneity in soil aggregates. In P-rich areas of all investigated soil aggregates, P was predominantly co-located with aluminium and iron oxides and hydroxides, which are known to strongly adsorb P. Clay minerals were co-located with P only to a lesser extent. In the low-P topsoil aggregate, the majority of the P was bound organically. Aluminium and iron phosphate predominated in the quartz-rich low-P subsoil aggregate. Sorbed and mineral P phases determined P speciation in the high-P top- and subsoil, and apatite was only detected in the high-P subsoil aggregate. Lastly, our results indicate that micro-scale spatial and chemical heterogeneity of P influences P accessibility and bioavailability.

36 MATERIALS SCIENCE↗

Preferred orientations of laterally grown silicon films over amorphous substrates using the vapor–liquid–solid technique

A novel method has been optimized so that adhesion layers are no longer needed to reliably deposit patterned gold structures on amorphous substrates. Using this technique allows for the fabrication of amorphous oxide templates known as micro-crucibles, which confine a vapor–liquid–solid (VLS) catalyst of nominally pure gold to a specific geometry. Within these confined templates of amorphous materials, faceted silicon crystals have been grown laterally. The novel deposition technique, which enables the nominally pure gold catalyst, involves the undercutting of an initial chromium adhesion layer. Using electron backscatter diffraction it was found that silicon nucleated in these micro-crucibles were 30% single crystals, 45% potentially twinned crystals and 25% polycrystals for the experimental conditions used. Single, potentially twinned, and polycrystals all had an aversion to growth with the (1 0 0) surface parallel to the amorphous substrate. Closer analysis of grain boundaries of potentially twinned and polycrystalline samples revealed that the overwhelming majority of them were of the 60° Σ3 coherent twin boundary type. The large amount of coherent twin boundaries present in the grown, two-dimensional silicon crystals suggest that lateral VLS growth occurs very close to thermodynamic equilibrium. It is suggested that free energy fluctuations during growth or cooling, and impurities were the causes for this twinning.

36 MATERIALS SCIENCE↗

Influence of Hydronium Ions in Zeolites on Sorption

In presence of sufficient concentrations of water, stable hydrated hydronium ions are formed in inorganic solid acids such as zeolites. In their presence larger organic molecules can only adsorb in the pore volume not occupied by hydronium ions. In consequence, the available pore volume decreases proportionally to their concentrations. The higher charge density (the increasing ionic strength) induced by increasing hydronium ion concentration in zeolite crystalline induces higher activity coefficients of adsorbed substrates, weakening the interactions between the organic part of the molecules, favoring instead interactions with polar groups. The insight allows linking a collective property such as hydrophilicity and hydrophobicity of zeolites to specific interactions on the molecular level.

Eckstein, Sebastian↗

GaN nanowires with pentagon shape cross-section by ammonia-source molecular beam epitaxy

In this study, ammonia-based molecular beam epitaxy (NH 3 -MBE) was used to grow catalyst-assisted GaN nanowires on (11¯02) r-plane sapphire substrates. Dislocation free [112¯0] oriented nanowires are formed with pentagon shape cross-section, instead of the usual triangular shape facet configuration. Specifically, the cross-section is the result of the additional two nonpolar {101¯0} side facets, which appear due to a decrease in relative growth rate of the {101¯0} facets to the {101¯1} and {101¯1} facets under the growth regime in NH 3 -MBE. Compared to GaN nanowires grown by Ni-catalyzed metal–organic chemical vapor deposition, the NH 3 -MBE grown GaN nanowires show more than an order of magnitude increase in band-edge to yellow luminescence intensity ratio, as measured by cathodoluminescence, indicating improved microstructural and optical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗

Towards rational control of seed oil composition: dissecting cellular organization and flux control of lipid metabolism

Plant lipids represent a fascinating field of scientific study, in part due to a stark dichotomy in the limited fatty acid (FA) composition of cellular membrane lipids vs the huge diversity of FAs that can accumulate in triacylglycerols (TAGs), the main component of seed storage oils. With few exceptions, the strict chemical, structural, and biophysical roles imposed on membrane lipids since the dawn of life have constrained their FA composition to predominantly lengths of 16–18 carbons and containing 0–3 methylene-interrupted carbon-carbon double bonds in cis-configuration. However, over 450 “unusual” FA structures can be found in seed oils of different plants, and we are just beginning to understand the metabolic mechanisms required to produce and maintain this dichotomy. Here we review the current state of plant lipid research, specifically addressing the knowledge gaps in membrane and storage lipid synthesis from 3 angles: pathway fluxes including newly discovered TAG remodeling, key acyltransferase substrate selectivities, and the possible roles of “metabolons.”

59 BASIC BIOLOGICAL SCIENCES↗