Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RuN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Friction and wear of selected metals and alloys in sliding contact with AISI 440 C stainless steel in liquid methane and in liquid natural gas

Aluminum, titanium, beryllium, nickel, iron, copper, and several copper alloys were run in sliding contact with AISI 440C in liquid methane and natural gas. All of the metals run except copper and the copper alloys of tin and tin-lead showed severely galled wear scars. Friction coefficients varied from 0.2 to 1.0, the lowest being for copper, copper-17 wt. % tin, and copper-8 wt. % tin-22 wt. % lead. The wear rate for copper was two orders of magnitude lower than that of the other metals run. An additional order of magnitude of wear reduction was achieved by the addition of tin and/or lead to copper.

Wisander, D. W.↗
NASA NTRS1977

Reliability measurement during software development

Measurement of software reliability was carried out during the development of data base software for a multi-sensor tracking system. Every run made during this project was scored as success or failure, and supporting data were collected on forms for further analysis. The failure ratio (number of failures per calendar interval divided by total number of runs) and failure rate (number of failures divided by CPU time for the interval) were found to be consistent measures, on a month-to-month basis as well as from module to module, and therefore considered valid indicators of reliability in this environment. Trend lines could be established from these measurements that provide good visualization of the progress on the job as a whole as well as on individual modules. Over one-half of the observed failures were due to factors associated with the specific run submission rather than with the code proper.

Hecht, H.↗
NASA NTRS1980

"Three-dimensional" vibration fixture

Simple cube-shaped fixture reduces vibration-test time to one-third required previously. Three units are supported at once. During one run each unit is tested along one of axes. Units are repositioned on second run for tests along different axes. Three runs complete test; fixture can be set up to test small, lightweight high-production units.

Schumacher, C. A.↗
NASA NTRS1978

Continuous Czochralski Growth. Silicon Sheet Growth Development of the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

The JPL Continuous Czochralski Growth Facility is now essentially complete and is functional. In this reporting period, a silicon lump recharging device was designed, and a prototype was built which performed well in simulated recharge tests. The large chamber (designed to accommodate a 14-inch hot zone) was put into operation initially with the standard hot zone in order to compare performance with previous experience. Some modifications were made to the hot zones in the larger chamber due to considerably larger radiative heat losses. Several short (one-ingot) runs were performed and four continuous runs were attempted. The largest continuous run lasted 64 hours and produced 57 kilograms of ingot.

Merz, F.↗
NASA NTRS1979

NASA CF6 jet engine diagnostics program: Long-term CF6-6D low-pressure turbine deterioration

Back-to-back performance tests were run on seven airline low pressure turbine (LPT) modules and four new CF6-6D modules. Back-to-back test cell runs, in which an airline LPT module was directly compared to a new production module, were included. The resulting change, measured in fuel burn, equaled the level of LPT module deterioration. Three of the LPT modules were analytically inspected followed by a back-to-back test cell run to evaluate current refurbishment techniques.

Smith, J. J.↗
NASA NTRS1979

Friction measurements in piston-cylinder apparatus using quartz-coesite reversible transition

The value of friction determined by monitoring piston displacement as a function of nominal pressure on compression and decompression cycles at 1273 K is compared with the friction value obtained by reversing the quartz-coesite transition at 1273 and 1073 K in a talc-glass-alsimag cell (Akella and Kennedy, 1971) and a low-friction salt cell (Mirwald et al., 1975). Quenching runs at 1273 K gave double values of friction of 0.25 GPa for the talc-glass-alsimag cell and 0.03 GPa for the salt cell. The piston-displacement technique gave somewhat higher values. Use of piston-displacement hysteresis loops in evaluating the actual pressure on a sample may lead to overestimates for decompression runs and underestimates for compression runs.

Akella, J.↗
NASA NTRS1980

Silicon web process development

A barrier crucible design which consistently maintains melt stability over long periods of time was successfully tested and used in long growth runs. The pellet feeder for melt replenishment was operated continuously for growth runs of up to 17 hours. The liquid level sensor comprising a laser/sensor system was operated, performed well, and meets the requirements for maintaining liquid level height during growth and melt replenishment. An automated feedback loop connecting the feed mechanism and the liquid level sensing system was designed and constructed and operated successfully for 3.5 hours demonstrating the feasibility of semi-automated dendritic web growth. The sensitivity of the cost of sheet, to variations in capital equipment cost and recycling dendrites was calculated and it was shown that these factors have relatively little impact on sheet cost. Dendrites from web which had gone all the way through the solar cell fabrication process, when melted and grown into web, produce crystals which show no degradation in cell efficiency. Material quality remains high and cells made from web grown at the start, during, and the end of a run from a replenished melt show comparable efficiencies.

Duncan, C. S.↗
NASA NTRS1979

The phase of the ten-hour modulation in the Jovian magnetosphere /Pioneers 10 and 11/

The paper describes the study of the phase of the 10-hour modulation of energetic electrons seen by Pioneers 10 and 11 in the Jovian magnetosphere. Attention is given to the peaks rather than the valleys of each cycle because the peaks are where physically interesting features occur, such as particle acceleration, current sheets, etc. To identify the peaks, it is required that the instantaneous intensity be higher than the 5-hour running average and the 5-hour running average be greater than the 10-hour running average. These criteria select an interval rather than a point and it is determined that this interval is an appropriate estimate of the experimental uncertainty. When the phases of the peaks are plotted together, they create patterns which are discussed in terms of disk-like, clock-like, and rotating anomaly models of the magnetosphere. Each model fits some of the data, but no model explains all of the data convincingly. It is concluded that there is still no understanding of the configuration of the outer Jovian magnetosphere.

Fillius, W.↗
NASA NTRS1980

Smoke characteristics of distillate and residual fuel burning in gas turbine combustors

During the development of a rich-lean staged dry low NOx combustor, the conventional trend of increasing smoke with increasing operating equivalence ratio was found when tests were run with distillate fuel (% H = 13.0). However, when tests were run with residual fuel (% H = 11.4), the trend was reversed. In addition, when the same combustor was run with blends of distillate fuel and residual fuel, a drastic improvement of smoke was observed when only 6 percent of residual fuel was mixed with distillate fuel, and for any blending of more than 10 percent of residual fuel the combustor was practically smoke free. A chemical analysis of fuel samples revealed an appreciable amount of trace metals in the residual fuel, giving rise to the suspicion that the smoke reduction may have been due in part to these trace metals. Of these elements found, vanadium is believed to be the most likely to cause smoke reduction because of its relatively high concentration.

Liu, T. M.↗
NASA NTRS1981

Holographic flow visualization at the Langley Expansion Tube

A holographic system used for flow visualization at the Langley Expansion Tube is described. A ruby laser which can be singly or doubly pulsed during the short run time of less than 300 microns is used as the light source. With holography, sensitivity adjustments can be optimized after a run instead of before a run as with conventional flow visualization techniques. This results in an increased reliability of the flow visualization available for the study of real-gas effects on flow about models. Holographic techniques such as single-plate schlieren and shadowgraph, two plate interferometry, double pulse interferometry for perfect infinite-fringe interferograms, and double-pulse interferometry used to examine changes in the flow over a short time period are described and examples presented.

Goad, W. K.↗
NASA NTRS1981

Development of Advanced Czochralski Growth Process to produce low cost 150 KG silicon ingots from a single crucible for technology readiness

The modified CG2000 crystal grower construction, installation, and machine check-out was completed. The process development check-out proceeded with several dry runs and one growth run. Several machine calibrations and functional problems were discovered and corrected. Several exhaust gas analysis system alternatives were evaluated and an integrated system approved and ordered. A contract presentation was made at the Project Integration Meeting at JPL, including cost-projections using contract projected throughput and machine parameters. Several growth runs on a development CG200 RC grower show that complete neck, crown, and body automated growth can be achieved with only one operator input. Work continued for melt level, melt temperature, and diameter sensor development.

Source record↗
NASA NTRS1981

Silicon solar cell process development, fabrication and analysis

Solar cells were fabricated from EFG ribbons dendritic webs, cast ingots by heat exchanger method, and cast ingots by ubiquitous crystallization process. Baseline and other process variations were applied to fabricate solar cells. EFG ribbons grown in a carbon-containing gas atmosphere showed significant improvement in silicon quality. Baseline solar cells from dendritic webs of various runs indicated that the quality of the webs under investigation was not as good as the conventional CZ silicon, showing an average minority carrier diffusion length of about 60 um versus 120 um of CZ wafers. Detail evaluation of large cast ingots by HEM showed ingot reproducibility problems from run to run and uniformity problems of sheet quality within an ingot. Initial evaluation of the wafers prepared from the cast polycrystalline ingots by UCP suggested that the quality of the wafers from this process is considerably lower than the conventional CZ wafers. Overall performance was relatively uniform, except for a few cells which showed shunting problems caused by inclusions.

Yoo, H. I.↗
NASA NTRS1981

Development of advanced Czochralski growth process to produce low-cost 150 kG silicon ingots from a single crucible for technology readiness

The modified CG2000 crystal grower construction, installation, and machine check out was completed. The process development check out proceeded with several dry runs and one growth run. Several machine calibrations and functional problems were discovered and corrected. Exhaust gas analysis system alternatives were evaluated and an integrated system approved and ordered. Several growth runs on a development CG2000 RC grower show that complete neck, crown, and body automated growth can be achieved with only one operator input.

Source record↗
NASA NTRS1982

Power spectral measurements of clear-air turbulence to long wavelengths for altitudes up to 14,000 meters

Measurements of three components of clear air atmospheric turbulence were made with an airplane incorporating a special instrumentation system to provide accurate data resolution to wavelengths of approximately 12,500 m (40,000 ft). Flight samplings covered an altitude range from approximately 500 to 14,000 m (1500 to 46,000 ft) in various meteorological conditions. Individual autocorrelation functions and power spectra for the three turbulence components from 43 data runs taken primarily from mountain wave and jet stream encounters are presented. The flight location (Eastern or Western United States), date, time, run length, intensity level (standard deviation), and values of statistical degrees of freedom for each run are provided in tabular form. The data presented should provide adequate information for detailed meteorological correlations. Some time histories which contain predominant low frequency wave motion are also presented.

Murrow, H. N.↗
NASA NTRS1981

Influence of surface-albedo in subtropical regions on July circulation

A simulation study to examine the influence of surface-albedo on July circulation in subtropical regions is presented. The results are based on two 47-day integrations. In the first integration, called the control run, surface albedos were normally prescribed, whereas in the second integration, called the anomaly run, the surface albedo was modified in four regions: the Sahel in Africa, the Great Plains in the United States, the Thar Desert border in the Indian subcontinent, and Brazil in South America. Each run was started from observed initial conditions for June 15, 1979 based on NMC analysis. The surface albedo in each of the regions was arbitrarily made 30%.

Sud, Y.↗
NASA NTRS1982

Agricultural Airplane Mission Time Structure Characteristics

The time structure characteristics of agricultural airplane missions were studied by using records from NASA VGH flight recorders. Flight times varied from less than 3 minutes to more than 103 minutes. There was a significant reduction in turning time between spreading runs as pilot experience in the airplane type increased. Spreading runs accounted for only 25 to 29 percent of the flight time of an agricultural airplane. Lowering the longitudinal stick force appeared to reduce both the turning time between spreading runs and pilot fatigue at the end of a working day.

Jewel, J. W., Jr.↗
NASA NTRS1982

Snowmelt runoff modeling in simulation and forecasting modes with the Martinec-Mango model

The Martinec-Rango snowmelt runoff model was applied to two watersheds in the Rio Grande basin, Colorado-the South Fork Rio Grande, a drainage encompassing 216 sq mi without reservoirs or diversions and the Rio Grande above Del Norte, a drainage encompassing 1,320 sq mi without major reservoirs. The model was successfully applied to both watersheds when run in a simulation mode for the period 1973-79. This period included both high and low runoff seasons. Central to the adaptation of the model to run in a forecast mode was the need to develop a technique to forecast the shape of the snow cover depletion curves between satellite data points. Four separate approaches were investigated-simple linear estimation, multiple regression, parabolic exponential, and type curve. Only the parabolic exponential and type curve methods were run on the South Fork and Rio Grande watersheds for the 1980 runoff season using satellite snow cover updates when available. Although reasonable forecasts were obtained in certain situations, neither method seemed ready for truly operational forecasts, possibly due to a large amount of estimated climatic data for one or two primary base stations during the 1980 season.

Shafer, B.↗
NASA NTRS1983

Tribological measurements on a Charnley-type artificial hip joint

A total hip simulator was used to determine the friction and wear properties of Charnley-type (316L stainless steel balls and sterile ultrahigh molecular weight polyethylene cups) hip prostheses. Three different sets of specimens were tested to 395,000, 101,500 and 233,000 walking cycles, respectively. All tests were run unlubricated, at ambient conditions (22 to 26 C, 30 to 50 percent relative humidity), at 30 walking cycles per minute, under a dynamic load simulating walking. Polyethylene cup wear rates ranged from 1.4 to 39 ten billions cu m which corresponds to dimensional losses of 4.0 to 11 microns per year. Although these wear rates are lower than those obtained from other hip simulators and from in vivo X-ray measurements, they are comparable when taking run-in and plastic deformation into account. Maximum tangential friction forces ranged from 93 to 129 N under variable load (267 to 3090 N range) and from 93 to 143 N under a static load of 3090 N. A portion of one test 250,000 walking cycles) run under dry air ( 1 percent relative humidity) yielded a wear rate almost 6 times greater than that obtained under wet air ( 70 percent relative humidity) conditions.

Jones, W. R., Jr.↗