Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Tensile and compressive creep behavior of extruded Mg–10Gd–3Y–0.5Zr (wt.%) alloy

The tensile and compressive creep behavior of an extruded Mg–10Gd–3Y–0.5Zr (wt.%) alloy was investigated at temperatures ranging from 200 °C to 300 °C and under stresses ranging from 30 MPa to 120 MPa. There existed an asymmetry in the tensile and compressive creep properties. The minimum creep rate of the alloy was slightly greater in tension than in compression. The measured values of the transient strain and initial creep rate in compression were greater than those in tension. The creep stress exponent was approximately 2.5 at low temperatures (T < 250 °C) and 3.4 at higher temperatures both in tension and in compression. The compression creep activation energy at low temperatures and high temperatures was 83.4 and 184.3 kJ/mol respectively, while one activation energy (184 kJ/mol) represented the tensile–creep behavior over the temperature range examined. Dislocation creep was suggested to be the main mechanism in tensile creep and in the high-temperature regime in compressive creep, while grain boundary sliding was suggested to dominate in the low-temperature regime in compressive creep. Precipitate free zones were observed near grain boundaries perpendicular to the loading direction in tension and parallel to the loading direction in compression. Electron backscattered diffraction analysis revealed that the texture changed slightly during creep. Non-basal slip was suggested to contribute to the deformation after basal slip was introduced. In the tensile–creep ruptured specimens, intergranular cracks were mainly observed at general high-angle boundaries. - Highlights: • Creep behavior of an extruded Mg–RE alloy was characterized by EBSD. • T5 aging treatment enhanced the tension–compression creep asymmetry. • The grains grew slightly during tensile creep, but not for compressive creep. • Precipitate free zones (PFZs) were observed at specific grain boundaries. • Intergranular fracture was dominant and cracks mainly originated at GHABs.

36 MATERIALS SCIENCE↗

Effect of minor carbon additions on the high-temperature creep behavior of a single-crystal nickel-based superalloy

Different amounts of carbon were added to a single-crystal nickel-based superalloy. The microstructural evolution of these alloys before and after high-temperature creep tests was investigated by employing scanning electron microscopy and transmission electron microscopy. Upon increasing the carbon contents, the volume fraction and diameter of the carbides increased gradually: however, the creep lives of the alloys increased slightly at first and subsequently decreased. The formation of second-phase particles, such as the nano-sized M{sub 23}C{sub 6}, blocky and needle-shaped μ phase, was observed in the creep samples, which was closely related to the high-temperature creep behaviors. - Highlights: • Creep behaviors of alloys with different amounts of carbon were investigated. • The creep rupture lives increased and later decreased with more carbon. • Second-phase particles were responsible for the different creep behaviors.

36 MATERIALS SCIENCE↗

A study of the deformation and failure mechanisms of protective intermetallic coatings on AZ91 Mg alloys using microcantilever bending

In this study, a nanoindentation-based microcantilever bending technique was utilized to investigate the interfacial properties of a β-Mg{sub 17}Al{sub 12}/AZ91 Mg alloy film/substrate system under tensile loading conditions. Finite element analysis (FEA) was first undertaken to optimise the design of cantilever structures for inducing high tensile stresses at the interface. Cantilevers consisting of a necked region or notch at the interface were determined to be the most successful designs. Microcantilevers containing the β-Mg{sub 17}Al{sub 12}/AZ91 interface were then made using focused ion beam (FIB) milling technique. Necks were made in the cantilevers to intensify the tension at the interface and notches were used to introduce a stress concentration to the interface. During bending, the cantilevers were deflected to failure. Subsequent analysis of the deformed cantilevers using electron microscopies revealed that plastic deformation, and subsequent ductile rupture, of the AZ91 phase was the dominant failure mechanism. When the β-Mg{sub 17}Al{sub 12}/AZ91 film/substrate system was subjected to tension, the softer AZ91 phase failed prior to interfacial delamination, demonstrating that the strength of the interface exceeded the stresses that caused ductile failure in the substrate material. - Highlights: •Microcantilever bending was used to study the property of film/substrate interface. •FEA was used to optimise cantilever design for achieving high interfacial tension. •The intermetallic coatings on AZ91 substrate have strong interfacial adhesion.

36 MATERIALS SCIENCE↗

Formation of TiO2 nanoribbons by anodization under high current density

Highlights: • TiO{sub 2} nanotubes were obtained under low current density. • TiO{sub 2} nanoribbons were obtained under high current density. • The pore walls of top TiO{sub 2} nanotubes are obviously thinner than other part. • Micro-liquid-flow causes the appearance of TiO{sub 2} nanoribbons. - Abstract: Highly ordered TiO{sub 2} nanoribbons are obtained by anodizations in NH{sub 4}F electrolyte under high current density. Although intact TiO{sub 2} nanoribbons appear, there are still nanotubes beneath nanoribbons. It is reasonable to speculate that TiO{sub 2} nanoribbons evolve from TiO{sub 2} nanotubes. While the applied current is high, the electronic current is also high, which gives rise to lots of oxygen bubbles. With the accumulation of oxygen bubbles, oxygen bubbles must expand upward and rupture finally. Therefore, gas flow from oxygen bubbles results in the generation of micro-liquid-flow. Because of micro-liquid-flow, the nanotube wall is corroded and scoured. The corrosion of upper pore wall is the most sever and thus the upper pore wall becomes the thinnest locality of nanotube wall. As a result, the nanotubes can collapse easily. Finally, one TiO{sub 2} nanotube is divided into several TiO{sub 2} nanoribbons while there is still intact tube beneath nanoribbons.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Creep behavior of commercial FeCrAl foils: beneficial and detrimental effect of oxidation

Creep tests were performed at 875 and 1050 C on commercially available FeCrAl foils (~50 m, 2 mil thickness) over a wide range of stress and duration to characterize their creep behavior. The oxide scales formed on the creep specimens were analyzed and compared to those that formed on unstressed specimens to assess the effect of stress and strain on oxide growth mechanisms. Below a specific stress threshold, creep rate and lifetime become independent of the applied load and rupture occurs due to the onset of breakaway oxidation. A creep rate model based on the strengthening of the FeCrAl foils due to load-bearing by the thermally-grown alumina scale was observed to be in good agreement with the experimental results.

36 MATERIALS SCIENCE↗

Comparison of the effects of semicarbazide and {beta}-aminopropionitrile on the arterial extracellular matrix in the Brown Norway rat

To investigate a putative role for semicarbazide-sensitive amine oxidase (SSAO) in arterial extracellular matrix (ECM) organization, we compared arteries of growing Brown Norway (BN) rats after chronic administration of semicarbazide (SCZ) and {beta}-aminopropionitrile (BAPN), two inhibitors with different properties and relative specificities for SSAO and lysyl oxidase (LOX). The BN model is particularly well adapted to evaluating effects of toxic compounds on the arterial elastic network. We measured aortic LOX and SSAO activities and quantified several ECM parameters. After a pilot study comparing doses previously studied and testing for additivity, we studied low and high equimolar doses of SCZ and BAPN. Both compounds similarly inhibited LOX, whereas SCZ inhibited SSAO far more effectively than BAPN. Both decreased carotid wall rupture pressure, increased tail tendon collagen solubility, decreased aortic insoluble elastin (% dry weight) and dose-dependently increased defects in the internal elastic lamina of abdominal aorta, iliac and renal arteries. Our results suggest that either these effects are mediated by LOX inhibition, SCZ being slightly more effective than BAPN in our conditions, or SSAO acts similarly to and in synergy with LOX on ECM, the greater SCZ effect reflecting the simultaneous inhibition of both enzymes. However, the high SCZ dose increased aortic collagen and ECM proteins other than insoluble elastin markedly more than did equimolar BAPN, possibly revealing a specific effect of SSAO inhibition. To discriminate between the two above possibilities, and to demonstrate unequivocally a specific effect of SSAO inhibition on ECM formation or organization, we must await availability of more specific inhibitors.

60 APPLIED LIFE SCIENCES↗

Interaction Between the Himalaya and the Flexed Indian Plate--Spatial Fluctuations in Seismic Hazard in India in the Past Millennium?

Between the tenth and early 16th centuries three megaquakes allowed most of the northern edge of the Indian plate to slip 20-24 m northward relative to the overlying Himalaya. Although the renewal time for earthquakes with this large amount of slip is less than 1300 years given a geodetic convergence rate of 16-20 mm/yr, recently developed scaling laws for the Himalaya suggest that the past 200 years of great earthquakes may be associated with slip of less than 10 m and renewal times of approximately 500 years. These same theoretical models show that the rupture lengths of the Himalaya's Medieval earthquakes (300-600 km) are too short to permit 24 m of slip given the relationships demonstrated by recent events. There is thus reason to suppose that recent earthquakes may have responded to different elastic driving forces from those that drove the megaquakes of Medieval times.An alternative source of energy to drive Himalayan earthquakes exists in the form of the elastic and gravitational energy stored in flexure of the Indian plate. The flexure is manifest in the form of a 200-450 m high bulge in central India, which is sustained by the forces of collision and by the end-loading of the plate by the Himalaya and southern Tibet. These flexural stresses are responsible for earthquakes in the sub-continent. The abrupt release of stress associated with the northward translation of the northern edge of the Indian plate by 24 m, were the process entirely elastic, would result in a deflation of the crest of the bulge by roughly 0.8 m. Geometrical changes, however, would be moderated by viscous rheologies in the plate and by viscous flow in the mantle in the following centuries.The hypothesized relaxation of flexural geometry following the Himalayan megaquake sequence would have the effect of backing-off stresses throughout central India resulting in quiescence both in the Himalaya and the Indian plate. The historical record shows an absence of great Himalayan earthquakes in the late 16th to early 19th centuries, and colonial records for this period contain few records of earthquakes in central India. Although this may be an artifact caused by a poor recorded history, it is unlikely that Mw>8.2 earthquakes have escaped notice in the Mughal or early colonial histories.Recent mid-plate earthquakes in India may thus represent a redevelopment of flexural stressing of the Indian plate. Their return also signifies the development of stresses in the Himalaya that will eventually be released in great Himalayan earthquakes.

58 GEOSCIENCES↗

Seismic Hazard Assessment of Tehran Based on Arias Intensity

In this paper probabilistic seismic hazard assessment of Tehran for Arias intensity parameter is done. Tehran is capital and most populated city of Iran. From economical, political and social points of view, Tehran is the most significant city of Iran. Since in the previous centuries, catastrophic earthquakes have occurred in Tehran and its vicinity, probabilistic seismic hazard assessment of this city for Arias intensity parameter is useful. Iso-intensity contour lines maps of Tehran on the basis of different attenuation relationships for different earthquake periods are plotted. Maps of iso-intensity points in the Tehran region are presented using proportional attenuation relationships for rock and soil beds for 2 hazard levels of 10% and 2% in 50 years. Seismicity parameters on the basis of historical and instrumental earthquakes for a time period that initiate from 4th century BC and ends in the present time are calculated using Tow methods. For calculation of seismicity parameters, the earthquake catalogue with a radius of 200 km around Tehran has been used. SEISRISKIII Software has been employed. Effects of different parameters such as seismicity parameters, length of fault rupture relationships and attenuation relationships are considered using Logic Tree.

58 GEOSCIENCES↗

Prediction of Seismic Slope Displacements by Dynamic Stick-Slip Analyses

A good-working balance between simplicity and reliability in assessing seismic slope stability is represented by displacement-based methods, in which the effects of deformability and ductility can be either decoupled or coupled in the dynamic analyses. In this paper, a 1D lumped mass 'stick-slip' model is developed, accounting for soil heterogeneity and non-linear behaviour, with a base sliding mechanism at a potential rupture surface. The results of the preliminary calibration show a good agreement with frequency-domain site response analysis in no-slip conditions. The comparison with rigid sliding block analyses and with the decoupled approach proves that the stick-slip procedure can result increasingly unconservative for soft soils and deep sliding depths.

58 GEOSCIENCES↗

The Seismic Reliability of Offshore Structures Based on Nonlinear Time History Analyses

Regarding the past earthquakes damages to offshore structures, as vital structures in the oil and gas industries, it is important that their seismic design is performed by very high reliability. Accepting the Nonlinear Time History Analyses (NLTHA) as the most reliable seismic analysis method, in this paper an offshore platform of jacket type with the height of 304 feet, having a deck of 96 feet by 94 feet, and weighing 290 million pounds has been studied. At first, some Push-Over Analyses (POA) have been preformed to recognize the more critical members of the jacket, based on the range of their plastic deformations. Then NLTHA have been performed by using the 3-components accelerograms of 100 earthquakes, covering a wide range of frequency content, and normalized to three Peak Ground Acceleration (PGA) levels of 0.3 g, 0.65 g, and 1.0 g. By using the results of NLTHA the damage and rupture probabilities of critical member have been studied to assess the reliability of the jacket structure. Regarding that different structural members of the jacket have different effects on the stability of the platform, an 'importance factor' has been considered for each critical member based on its location and orientation in the structure, and then the reliability of the whole structure has been obtained by combining the reliability of the critical members, each having its specific importance factor.

58 GEOSCIENCES↗

Interfacial reactions and resistive switching behaviors of metal/NiO/metal structures

Ag/NiO/Pt structures did (did not) exhibit reproducible resistive switching when a positive bias was applied to the Pt (Ag) electrode. X-ray photoemission spectra revealed that ultrathin NiO films on Pt (Ag) layers did (did not) undergo reversible chemical state change during heat treatment in a vacuum and oxygen ambient. Such differences in interfacial chemical interaction may affect filament formation and rupture processes near the electrode and hence alter the resistive switching behaviors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fissile Nuclei Rotation Effect in {sup 235}U(n,{gamma}f) Process

A small shift of an angular distribution of prompt {gamma}-rays relative to the fission axis of {sup 236}U* {sup 235}U(n,{gamma}f) process is presented. This effect has been observed in the experiment at BER-II reactor of BENSC/HMI (Berlin). The sign of the shift depends on the direction of the incident neutron beam polarization. This phenomena can be explained by the rotation of fissile nucleus {sup 236}U*, like the effect that has been observed recently at ILL in ternary fission of {sup 235}U by cold polarized neutrons. The main surprise of this result is the detection of scission gamma-rays radiated by a fissile nucleus during the time interval of the order of 10{sup -21} s before or after the moment of the neck rupture. Detailed measurements of trigger {gamma}-rays energy dependence are in progress at the neutron beam 'MEPHISTO' of FRM-II reactor (Garching)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Interaction of a high-power laser beam with metal sheets

Experiments with a high-power laser beam directed onto thin aluminum sheets, with a large spot size, demonstrate that airflow produces a strong enhancement of the interaction. The enhancement is explained in terms of aerodynamic effects. As laser heating softens the material, the airflow-induced pressure difference between front and rear faces causes the metal to bulge into the beam. The resulting shear stresses rupture the material and remove it at temperatures well below the melting point. The material heating is shown to conform to an elementary model. We present an analytic model of elastic bulging. Scaling with respect to spot size, wind speed, and material parameters is determined.

36 MATERIALS SCIENCE↗

Hydrogen and Materials: Influence of the Hydrogen Environment on the Metallic Materials Behavior

The materials sensitivity to hydrogen is studied and measured in this work using the disk pressure testing, whose principle is the comparison of the rupture parameters obtained with metallic membranes tested similarly under helium and hydrogen. Such technique allows various studies and reveals parameters that remain not significant with less sensitive methods. This work presents an overview of numerous experimental results concerning the influence of various factors (material and gas composition, mechanical and heat treatments, type of microstructure...) on the hydrogen embrittlement of ferrous and nonferrous alloys. There are shown synergies between such factors, related to physical and metallurgical phenomena and we give some practical considerations, which can be useful for the evaluation of the safety offered by different materials in contact with hydrogen and for searching ways to improve their behavior.

36 MATERIALS SCIENCE↗

SAFETY ASPECTS OF BIG CRYOGENIC SYSTEMS DESIGN

Superconductivity and helium cryogenics are key technologies in the construction of large scientific instruments, like accelerators, fusion reactors or free electron lasers. Such cryogenic systems may contain more than hundred tons of helium, mostly in cold and high-density phases. In spite of the high reliability of the systems, accidental loss of the insulation vacuum, pipe rupture or rapid energy dissipation in the cold helium can not be overlooked. To avoid the danger of over-design pressure rise in the cryostats, they need to be equipped with a helium relief system. Such a system is comprised of safety valves, bursting disks and optionally cold or warm quench lines, collectors and storage tanks. Proper design of the helium safety relief system requires a good understanding of worst case scenarios. Such scenarios will be discussed, taking into account different possible failures of the cryogenic system. In any case it is necessary to estimate heat transfer through degraded vacuum superinsulation and mass flow through the valves and safety disks. Even if the design of the helium relief system does not foresee direct helium venting into the environment, an occasional emergency helium spill may happen. Helium propagation in the atmosphere and the origins of oxygen-deficiency hazards will be discussed.

42 ENGINEERING↗

GUIDELINES FOR THE DESIGN, FABRICATION, TESTING, INSTALLATION AND OPERATION OF SRF CAVITIES

Superconducting Radio-Frequency (SRF) cavities containing cryogens under pressure pose a potential rupture hazard to equipment and personnel. Generally, pressure vessels fall within the scope of the ASME Boiler and Pressure Vessel Code however, the use of niobium as a material for the SRF cavities is beyond the applicability of the Code. Fermilab developed a guideline to ensure sound engineering practices governing the design, fabrication, testing, installation and operation of SRF cavities. The objective of the guideline is to reduce hazards and to achieve an equivalent level of safety afforded by the ASME Code. The guideline addresses concerns specific to SRF cavities in the areas of materials, design and analysis, welding and brazing, pressure relieving requirements, pressure testing and quality control.

42 ENGINEERING↗

Self-Pierce Riveting of Three Aluminium Alloy and Mild Steel Sheets

Three aluminium alloy and steel sheets were joined with a self-piercing rivet. Self-pierce riveting has the function of joining steel and aluminium alloys having very different melting points due to plastic joining. The requisites for joining the three sheets are the driving of the rivet leg through the middle sheet, the flaring of the rivet leg in the lower sheet and the prevention of the fracture of the lower sheet. The joinability for various combinations of the three sheets was determined. When the rivet leg is small, no driving through the middle sheet occurs, the lower sheet ruptures for a large rivet leg. In addition, 980 MPa high strength steel, mild steel and aluminium alloy sheets were joined by the self-pierce riveting.

36 MATERIALS SCIENCE↗

Multiscale Modeling of the Orthotropic Behaviour of PA6-6 overmoulded Composites using MMI Approach

In this study the MMI ConfidentDesign multiscale approach (consisting in a non-linear multiscale simulation based on DIGIMAT registered including the injection modeling of the filled polymer and a multiscale mechanical model using the fiber orientation tensor resulting from the injection) has been combined with an orthotropic damageable elastic simulation. The anisotropic properties (including rupture criterion) are estimated and a multiscale simulation including the heterogeneous material properties issued from injection process is done. The impact of fiber ratios is then investigated. The structural simulation predicts stresses localized close to the punch, as well in injected PA66 than in composite part. Greater the fiber volume ratio, greater the modulus and more brittle the composite.

36 MATERIALS SCIENCE↗