Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mixture experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

CVB: the Constrained Vapor Bubble Capillary Experiment on the International Space Station MARANGONI FLOW REGION

The Constrained Vapor Bubble (CVB) is a wickless, grooved heat pipe and we report on a full- scale fluids experiment flown on the International Space Station (ISS). The CVB system consists of a relatively simple setup a quartz cuvette with sharp corners partially filled with either pentane or an ideal mixture of pentane and isohexane as the working fluids. Along with temperature and pressure measurements, the two-dimensional thickness profile of the menisci formed at the corners of the quartz cuvette was determined using the Light Microscopy Module (LMM). Even with the large, millimeter dimensions of the CVB, interfacial forces dominate in these exceedingly small Bond Number systems. The experiments were carried out at various power inputs. Although conceptually simple, the transport processes were found to be very complex with many different regions. At the heated end of the CVB, due to a high temperature gradient, we observed Marangoni flow at some power inputs. This region from the heated end to the central drop region is defined as a Marangoni dominated region. We present a simple analysis based on interfacial phenomena using only measurements from the ISS experiments that lead to a predictive equation for the thickness of the film near the heated end of the CVB. The average pressure gradient for flow in the film is assumed due to the measured capillary pressure at the two ends of the liquid film and that the pressure stress gradient due to cohesion self adjusts to a constant value over a distance L. The boundary conditions are the no slip condition at the wall interface and an interfacial shear stress at the liquid- vapor interface due to the Marangoni stress, which is due to the high temperature gradient. Although the heated end is extremely complex, since it includes three- dimensional variations in radiation, conduction, evaporation, condensation, fluid flow and interfacial forces, we find that using the above simplifying assumptions, a simple successful model can be developed.

heat pipes↗

Ab initio studies of Nb–N–S tri-doped TiO{sub 2} with enhanced visible light photocatalytic activity

The electronic and optical properties of Nb–N–S tri-doped anatase TiO{sub 2} were investigated within the frame of the density functional theory (DFT) plus U method. Results show that a significant red-shift effect and improvement of visible-light absorption for Nb–N–S tri-doped TiO{sub 2} are observed with respect to pure TiO{sub 2} and S–N codoped TiO{sub 2}. At the same time, the enhanced visible-light photocatalytic activity of tri-doped TiO{sub 2} is derived from the narrowing band gap, the appearance of Nb 4d state at the bottom of conduction band and the mixture of N 2p, S 3p states forming new defect levels at the top of valance band, which is excellently consistent with the previous experiment. Moreover, S ion leads to the lattice distortion and promotes the visible-light photocatalytic activity. Furthermore, the absorbance of 1.39NbNS–TiO{sub 2} accords well with the experimental result in the visible region. It is also found that the 2.78NbNS–TiO{sub 2} can be easily grown under O-rich condition and have the strongest absorbance from 2.0 to 4.2 eV among four models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Initiation of Flash Boiling of Multicomponent Miscible Mixtures with Application to Transportation Fuels and Their Surrogates

This paper presents methodologies to predict thermodynamic conditions that initiate flash boiling by spontaneous nucleation of liquids consisting of hundreds of miscible liquids and their lower order surrogate mixtures. The methods are illustrated with a kerosene-based fuel and a seven-component surrogate for it. The predictions are compared to measurements of nucleation temperatures obtained from a pulse-heating technique that rapidly heats a microscale platinum film immersed in a pool of the test fluid. Nucleation temperatures are predicted using a generalized corresponding states principle (GCSP), and a modification of classical nucleation theory that considers the mixture as a pseudo single component fluid (PSCF). The intent is to offer a simple means to predict the initiation of flash boiling that can have important consequences for fuel efficiency in combustion engines. We show that contact angle has a strong effect such that predicted and measured spontaneous nucleation temperatures agree for a given heating rate only if contact angle is accounted for in the theory. For low heating rates (less than 2 × 10 7 K/s), predicted nucleation temperatures, assuming a spherical bubble, are 13% higher than measurements. The gap is closed to about 6% as the heating rate reaches 3 × 10 8 K/s (the highest that could be reached in the experiments) and to less than 1% when the measured nucleation temperature is extrapolated to an asymptotic (zero contact angle) limit. Here, the PSCF method (using mixture properties as mole fraction averages of mixture component properties evaluated at the same reduced temperatures as the mixtures) and the GSCP predict virtually identical nucleation temperatures, while the GCSP method does not require any mixture property values.

42 ENGINEERING↗

Structural features of bicomponent dust Coulomb balls formed by the superposition of fields of different origin in plasma

A binary mixture of dust particles in plasma which are in an external electrostatic harmonic confining field as well as in the field consisting of gravitational, thermophoretic, and electrostatic force is simulated. The interparticle interaction is described by the Yukawa isotropic pair potential. The structural properties of the binary mixture of particles depending on composition are investigated. The segregation features of a system of particles of two species under the conditions of recent experiments on Coulomb ball formation are studied. It is shown that particles form a shell structure in which every shell contains only its own species of particles; in so doing, smaller-sized particles make up outer shells with respect to larger-sized particles. When the size difference between the particles becomes more and more pronounced, they are spatially separated up to the formation of two independent Coulomb balls.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Evaluation of oxide-coated iridium-rhenium chambers

Iridium-coated rhenium (Ir-Re) provides long life operation of radiation-cooled rockets at temperatures up to 2200 C. Ceramic oxide coatings could be used to increase Ir-Re rocket lifetimes and allow operation in highly oxidizing environments. Ceramic oxide coatings promise to serve as both thermal and diffusion barriers for the iridium layer. Seven ceramic oxide-coated Ir-Re, 22-N rocket chambers were tested with gaseous hydrogen/gaseous oxygen (GHz/G02) propellants. Five chambers had thick (over 10 mils), monolithic coatings of either hafnia (HfO2) or zirconia (ZrO2). Two chambers had coatings with thicknesses less than 5 mils. One of these chambers had a thin-walled coating of ZrO2 infiltrated with sol gel HfO2. The other chamber had a coating composed of an Ir-oxide composite. The purpose of this test program was to assess the ability of the oxide coatings to withstand the thermal shock of combustion initiation, adhere under repeated thermal cycling, and operate in aggressively oxidizing environments. All of the coatings survived the thermal shock of combustion and demonstrated operation at mixture ratios up to 11. Testing the Ir-oxide composite-coated chamber included over 29 min at mixture ratio 16. The thicker walled coatings provided the larger temperature drops across the oxide layer (up to 570 C), but were susceptible to macrocracking and eventual chipping at a stress concentrator. The cracks apparently resealed during firing, under compression of the oxide layer. The thinner walled coatings did not experience the macrocracking and chipping of the chambers that was seen with the thick, monolithic coatings. However, burn-throughs in the throat region did occur in both of the thin-walled chambers at mixture ratios well above stoichiometric. The burn-throughs were probably the result of oxygen diffusion through the oxide coating that allowed the underlying Ir and Re layers to be oxidized. The results of this test program indicated that the thin-walled oxide coatings are better suited for repeated thermal cycling than the thick-walled coating, while thicker coatings may be required for operation in aggressively oxidizing environments.

Reed, Brian D.↗

Alternative Fuel Research in Fischer-Tropsch Synthesis

NASA Glenn Research Center has recently constructed an Alternative Fuels Laboratory which is solely being used to perform Fischer-Tropsch (F-T) reactor studies, novel catalyst development and thermal stability experiments. Facility systems have demonstrated reliability and consistency for continuous and safe operations in Fischer-Tropsch synthesis. The purpose of this test facility is to conduct bench scale Fischer-Tropsch (F-T) catalyst screening experiments while focusing on reducing energy inputs, reducing CO2 emissions and increasing product yields within the F-T process. Fischer-Tropsch synthesis is considered a gas to liquid process which reacts syn-gas (a gaseous mixture of hydrogen and carbon monoxide), over the surface of a catalyst material which is then converted into liquids of various hydrocarbon chain length and product distributions1. These hydrocarbons can then be further processed into higher quality liquid fuels such as gasoline and diesel. The experiments performed in this laboratory will enable the investigation of F-T reaction kinetics to focus on newly formulated catalysts, improved process conditions and enhanced catalyst activation methods. Currently the facility has the capability of performing three simultaneous reactor screening tests, along with a fourth fixed-bed reactor used solely for cobalt catalyst activation.

Surgenor, Angela D.↗

Single-Fuel Reactivity Controlled Compression Ignition Combustion Enabled by Onboard Fuel Reformation (Final Report)

Reactivity-Controlled Compression Ignition (RCCI) is a promising new advanced, low temperature combustion mode that offers efficiencies equal to or greater than conventional diesel combustion, but significantly lower soot and NOx emissions. Additionally, RCCI has enhanced controllability over the combustion process compared to some of the other advanced combustion modes. Therefore, RCCI combustion has the potential to be of great benefit to the public by increasing the efficiency and reducing the harmful pollutant emissions from transportation. However, RCCI combustion achieves this favorable level of performance through the use of two distinct fuels (e.g., diesel and gasoline, diesel and natural gas, or diesel and ethanol). In a vehicle application, RCCI therefore requires two different fuel tanks and fuel injection systems, which presents a significant drawback to the commercialization RCCI. This project proposed a new concept to enable RCCI combustion from a single parent fuel stored onboard the vehicle in a single fuel tank. Specifically, the parent fuel would be stored in the fuel tank and one branch of the fuel system would deliver the parent fuel, unaltered, to the cylinder, while a second branch of the fuel system would route the parent fuel through a fuel reformer to chemically react the fuel into a gaseous fuel mixture, called “reformate”, that has different properties from the original parent fuel. In this way, there can be two fuels at the engine that have different properties, but only one parent fuel needs to be stored and refilled in the vehicle. This initial, exploratory investigation into the feasibility of this promising new concept included reacting three potential parent fuels (diesel, gasoline, and natural gas) in a fuel reformer and determining the composition of the gaseous reformate fuel that exited the fuel reformer. There are different types of reformation processes, but since this project was a proof-of-concept investigation into the potential of Single-Fuel RCCI and the combustion process in the cylinder, a catalytic partial oxidation (CPOX) reformation process was selected, which is more straightforward to perform and control, and would potentially be easier to implement in a vehicle application compared to other reformation processes. Once the three parent fuels were reformed to varying degrees and their reformate compositions were determined, their autoignition tendencies were experimentally determined by comparing advanced combustion results of the reformate mixtures with known reference fuels. This showed that diesel fuel and its reformate fuel mixture exhibited the largest reactivity separation, which is necessary to enable RCCI combustion in the cylinder. Using diesel fuel as the parent fuel, experimental testing was conducted to provide a better understanding of the operational considerations, benefits, and drawbacks of Single-Fuel RCCI with onboard fuel reformation. The experimental testing was accompanied by computational fluid dynamics and system-level modeling to help complement the experiments and further expand the understanding. The main conclusions are that Single-Fuel RCCI using diesel fuel as the direct injected, high reactivity fuel and diesel’s gaseous reformate mixture as the premixed, low reactivity fuel is viable. The efficiencies were equal to, or sometimes greater than, RCCI with conventional fuel pairs, and the emissions were comparable as well. A key consideration is that gaseous reformate fuel contains a large amount of diluents in the fuel which displace air entering the cylinder and act as EGR inside the cylinder. Additionally, the reactivity separation between diesel and its reformate fuel mixture is larger than diesel-gasoline, but less than diesel-natural gas, and the combustion process therefore responded in a manner that was between the two conventional fuel pairs. Finally, although achievable in the cylinder, there are practical drawbacks or other disadvantages of Single-Fuel RCCI with onboard fuel reformation. First, this project used a CPOX reformation process which is exothermic, meaning that a portion of the fuel’s energy was released in the reformer where it could not be converted into useful work. This constituted an efficiency penalty of the system of on the order of 10% or 4 percentage points. Future research should therefore focus on alternate reforming processes including steam-methane reforming or autothermal reforming where there might not be any energy released in the reformer, or there could even be an energy gain in the reformer (through an endothermic process with waste heat recovery). Practical drawbacks that exist, but were beyond the scope of this preliminary proof-of-concept research project, are the added cost of the fuel reformer, which is a catalyst made of precious metals, transient response of the system, and the lifetime of the fuel reformer.

33 ADVANCED PROPULSION SYSTEMS↗

Deactivation and regeneration of ZSM-5 zeolite in catalytic pyrolysis of plastic wastes

Highlights: > Pyrolysis transforms plastic wastes in valuable liquids and gases useful as fuels or source of chemicals. > The use of ZSM-5 zeolite in pyrolysis favours the production of gases and of lighter and more aromatic liquids. > ZSM-5 zeolite is almost completely deactivated after one plastics pyrolysis experiment. > ZSM-5 zeolite used in plastic wastes pyrolysis can be regenerated by burning the deposited coke in an air stream. > Regenerated ZSM-5 recovers its activity and produces liquids and gases equivalent to those obtained with fresh catalyst. - Abstract: In this work, a study of the regeneration and reuse of ZSM-5 zeolite in the pyrolysis of a plastic mixture has been carried out in a semi-batch reactor at 440 deg. C. The results have been compared with those obtained with fresh-catalyst and in non-catalytic experiments with the same conditions. The use of fresh catalyst produces a significant change in both the pyrolysis yields and the properties of the liquids and gases obtained. Gases more rich in C3-C4 and H{sub 2} are produced, as well as lower quantities of aromatic liquids if compared with those obtained in thermal decomposition. The authors have proved that after one pyrolysis experiment the zeolite loses quite a lot of its activity, which is reflected in both the yields and the products quality; however, this deactivation was found to be reversible since after regeneration heating at 550 deg. C in oxygen atmosphere, this catalyst recovered its initial activity, generating similar products and in equivalent proportions as those obtained with fresh catalyst.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Numerical study of advanced compression ignition and combustion in a gasoline direct injection engine

Multi-mode combustion strategies may provide a considerable thermal efficiency improvement targeted at part-load operating conditions for light-duty spark-ignition (SI) engines. The extension from boosted SI mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing compression ratio and utilizing intake air heating. In order to enable an accurate control of intake charge condition for ACI control and rapid mode-switches, it is essential to gain fundamental insight into the autoignition process with regard to thermal and fuel-air mixture stratification in the combustion chamber. In this work, a computational fluid dynamics (CFD) study is carried out to reveal some degrees of correlation between the mixture and thermal stratifications induced by the cylinder wall temperature and combustion-phasing across varying engine load conditions. The computational analysis begins with a calibrated simulation setup best matching the engine experiments, and subsequently evaluates the baseline setup for an extended range of engine load conditions for two excess-air ratio cases. The present study emphasizes the dominance of thermal stratifications for autoignition process due to wall temperature effects depending on the engine load conditions of interest. In addition, this study also aims to provide insight into the impact of mixture stratification on cyclic variability, especially at colder wall engine conditions (e.g., cold start). Observations herein provide highlight of the propensity of autoignition in correlation with mixture reactivity space.

Advanced Compression Ignition (ACI) engine↗

HIGH-FIDELITY SIMULATION OF SOOT FORMATION AND THERMAL RADIATION IN A LABORATORY-SCALE RICH-QUENCH-LEAN BURNER

High-fidelity simulations of a swirl-stabilized turbulent spray flame in a laboratory-scale aero-combustor have been performed to evaluate the predictability of state-of-the-art models in capturing soot formation. The simulations employ a complex chemical mechanism developed for Jet-A with PAH chemistry, coupled with the Hybrid Method of Moments (HMOM) soot model, and a Lagrangian dilute spray model for the fuel injection. Two simulations are performed to compare the results when thermal radiation is neglected or included in the solution with a mean spectral model. Modeling closures for the soot differential diffusion effects in mixture fraction space, as well as turbulence-radiation interaction are also evaluated using the data generated by the simulations. Given the degree of complexity of the simulation, the results showed good agreement with experimental measurements of the spatial distribution of the soot volume fraction ensemble average. A closer agreement with the experiment is observed when thermal radiation is included in the solution. Thermal radiation is observed to reduce the flame temperature and increase the flame intermittency, denoted by the increase in the temperature standard deviation in mixture fraction space. The reduction in temperature also leads to a reduction in PAH production and soot volume fraction. Turbulence is observed to have different effects on radiative emission depending on the mixture fraction. Turbulent scalar fluctuations significantly enhance radiative emission in fuel lean mixtures and can also play a role for fuel rich conditions. The statistical description of the turbulence-radiation interaction, previously proposed in the literature, was observed to correctly reproduce the high-fidelity results. Model coefficients were provided for swirl-stabilized flames. The soot differential diffusion model, previously proposed in the literature, based on the residual between the exact term and its model approximation, was also evaluated. The residual correction term further improved the agreement with exact differential diffusion term evaluated with the high-fidelity simulation data in mixture fraction space. The results suggest that the effective turbulent Lewis number can be equal to unity in simulations of turbulent non-premixed recirculating flames.

Soriano, Bruno [Sandia National Laboratories (SNL)↗

Sorption and oxidation of Co(II) at the surface of birnessite: Impacts of aqueous Mn(II)

The sorption of aqueous Mn(II) (1 mM) and Co(II) (50 and 200 μM) onto hexagonal birnessite (0.1 g L –1 ) was studied under anoxic conditions at pH 6.5 and 7.5 in binary and ternary experiments using batch kinetic experiments and XRD, ATR-FTIR, and Co K-edge EXAFS analyses. In the binary systems, sorption of Co(II) was accompanied by partial oxidation to Co(III) yielding a mixture of corner-sharing Co(II) and edge-sharing Co(III) complexes at both pH values, while Mn(II)-birnessite interaction resulted in coordination of Mn(II/III) at layer vacancy sites at pH 6.5, and led to reductive transformation of birnessite into feitknechtite at pH 7.5. In the ternary systems, strong mutual interferences between Co(II) and Mn(II) co-sorbates reduced the rate and extent of sorption relative to the binary experiments. The introduction of Mn(II) aq into the high-Co systems (200 μM) halted the slow sorption of Co(II) that was attributed to the incorporation of Co(III) into layer vacancies, while Co(II) aq prevented Mn(II)-driven transformation of birnessite into feitknechtite at pH 7.5. In the low-Co system (50 μM), reductive transformation of birnessite by Mn(II) aq at pH 7.5 produced Co(II)-substituted feitknechtite, a conversion that was accompanied by reduction of sorbed Co(III) to Co(II) which was partially released to solution. The strong effects of co-sorption are attributed to the similarity in sorption mechanisms of Co(II) and Mn(II), which both sorb as a mixture of di- and trivalent species. Finally, the results of this work demonstrate that aqueous Mn(II) may significantly affect the reactivity of phyllomanganate sorbents towards dissolved Co(II), and therefore impact the speciation and solubility of this trace metal in anoxic and suboxic geochemical environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamics of multilayer Rayleigh–Taylor instability at moderately high Atwood numbers

This paper investigates the multilayer Rayleigh–Taylor instability (RTI) using statistically stationary experiments conducted in a gas tunnel. Employing diagnostics such as particle image velocimetry (PIV) and planar laser induced fluorescence (PLIF), we make simultaneous velocity–density measurements to study how dynamics and mixing are linked in this variable density flow. Experiments are conducted in a newly built, blow-down three-layer gas tunnel facility. Mixing between three gas streams is studied, where the top and bottom streams are comprised of air, and the middle stream is an air–helium mixture. Shear is minimized between these streams by matching their inlet velocities. The four experimental conditions investigated here consist of two different density ratios (Atwood numbers 0.3 and 0.6), each investigated at two instability development times (or equivalently, two streamwise locations), and all experiments are with the same middle stream thickness of 3 cm. The growth of the middle layer is measured using laser-based planar Mie scattering visualization. The mixing width is found to grow linearly with time at late times. Various quantitative measures of molecular mixing indicate a very high degree of molecular mixing at late times in the multilayer RTI flow. The vertical turbulent mass flux $a_y$ is calculated. In addition to mostly negative values of $a_y$ , typical of buoyancy-dominated flows due to negative correlation between velocity and density fluctuations, positive regions are also observed in profiles of $a_y$ due to entrainment and erosion at the lower edge of the mixing region. Global energy budgets are calculated for the multilayer RTI flow at late times and it is found that the majority of potential energy released has been dissipated due to viscous effects, and a large value of mixing efficiency ( $\sim$ 60 %) is observed.

Mechanics↗

Laboratory plasma physics experiments using merging supersonic plasma jets

We describe a laboratory plasma physics experiment at Los Alamos National Laboratory that uses two merging supersonic plasma jets formed and launched by pulsed-power-driven railguns. The jets can be formed using any atomic species or mixture available in a compressed-gas bottle and have the following nominal initial parameters at the railgun nozzle exit: n e ≈ n i ~ 10¹⁶ cm⁻³, T e ≈ T i ≈ 1.4 eV, V jet ≈ 30–100 km/s, mean charge $\bar{Z}$ ≈ 1, sonic Mach number M s ≡ V jet /C s > 10, jet diameter = 5 cm, and jet length ≈ 20 cm. Experiments to date have focused on the study of merging-jet dynamics and the shocks that form as a result of the interaction, in both collisional and collisionless regimes with respect to the inter-jet classical ion mean free path, and with and without an applied magnetic field. However, many other studies are also possible, as discussed in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NOx storage and reduction in model lean NOx trap catalysts studied by in situ DRIFTS

NO{sub x} storage and reduction on a model Pt/BaO/Al{sub 2}O{sub 3} catalyst was studied by means of in situ DRIFTS measurements. To examine the effect of ceria addition, experiments were also conducted using Pt/BaO/Al{sub 2}O{sub 3} to which Pt/CeO{sub 2} was added as a physical mixture in a 74:26 weight ratio. For the former catalyst, DRIFT spectra acquired during NO/O{sub 2} and NO{sub 2}/O{sub 2} storage indicated the formation of nitrite at 200 C during the initial stages of adsorption, while increasing the adsorption temperature appeared to facilitate the oxidation of nitrite to nitrate. The ceria-containing catalyst afforded similar DRIFT spectra under these conditions, although the presence of cerium nitrates was observed at 200 and 300 C, consistent with NO{sub x} storage on the ceria phase. DRIFT spectra acquired during NO{sub x} reduction in CO and CO/H{sub 2} showed that Ba nitrate species remained on the surface of both catalysts at 450 C, whereas the use of H{sub 2}-only resulted in complete removal of stored NO{sub x}. The observation of Ba carbonates when CO was present suggests that the inferior reduction efficiency of CO may arise from the formation of a crust of BaCO{sub 3} on the Ba phase, which inhibits further NO{sub x} reduction. DRIFT spectra acquired during lean-rich cycling (6.5 min lean, 1.0 min rich) with CO/H{sub 2} as the rich phase reductants revealed that a significant concentration of nitrates remained on the catalysts at the end of the rich phase. This implies that a large fraction of nitrate is not decomposed during cycling and thus cannot participate in NO{sub x} abatement through storage and regeneration.

33 ADVANCED PROPULSION SYSTEMS↗

Silicon alloying enhances fast heating rate combustion of aluminum particles

Alloys and composites of aluminum (Al) have shown promise in regulating and enhancing particle combustion for energy generation applications. Recent work on aluminum-silicon (Al-Si) spherical alloy particles has shown improved combustion at low heating rates through enhanced diffusion accompanying a lower melting temperature. This study extends reactivity analysis to higher heating rates, comparing oxidation of Al-Si with Al. Flame speeds of Al-Si powder mixed with molybdenum trioxide (MoO 3 ) powder (Al-Si+MoO 3 ) exhibited a faster transition to steady propagation relative to Al+MoO 3 . Bomb calorimetry experiments revealed up to 5.8% greater early temperature rise for Al-Si powder. Rapid steady propagation for Al-Si mixture and faster temperature rise for Al-Si particles were attributed to accelerated kinetics evidenced in thermal equilibrium analysis of the mixtures using a differential scanning calorimeter (DSC). Larger DSC exotherms in the early stages of oxidation (i.e., 480–720 °C) correlated with early heat release and promoted steady flame propagation for Al-Si+MoO 3 compared with Al+MoO 3 . Furthermore, in multiple heating rate DSC studies, Al-Si+MoO 3 ignited at a lower heating rate (i.e., 15 ⁰C/min) than Al+MoO 3 (i.e., 20 ⁰C/min). Both mixtures ignited at temperatures less than 625 °C which is above the melting temperature of Al-Si (574 °C) and below Al (659 °C). Thus, alloy particle fuels with enhanced diffusion-controlled kinetics promote steady flame propagation and show promise for energy generation applications. This is especially promising for technologies driven by enhanced condensed phase combustion such as some propellant additives or applications dependent on reliable burn rates such as pyrotechnic time delay formulations and primers.

36 MATERIALS SCIENCE↗

Catalytic conversion of biomass-derived ethanol to liquid hydrocarbon blend-stock: Effect of light gas recirculation

Here, we describe a light gas recirculation (LGR) method to increase the liquid hydrocarbon yield with reduced aromatic content from catalytic conversion of ethanol to hydrocarbons. The previous liquid hydrocarbon yield is ~40% from one-pass ethanol conversion over V-ZSM-5 at 350 C and atmospheric pressure where the remaining ~60% yield is light gas hydrocarbons. In comparison, the liquid hydrocarbon yield increases to 80% when a simulated light gas hydrocarbon stream is co-fed at a rate of 0.053 mol g-1 h-1 with ethanol due to the conversion of most of the light olefins. The LGR also significantly improves the quality of the liquid hydrocarbon blend-stock by reducing aromatic content and overall benzene concentration. For 0.027 mol g-1 h-1 light gas mixture co-feeding, the average aromatic content in liquid hydrocarbons is 51.5% compared with 62.5% aromatic content in ethanol only experiment. Average benzene concentration decreases from 3.75% to 1.5% which is highly desirable since EPA limits benzene concentration in gasoline to 0.62%. As a result of low benzene concentration, the blend-wall for ethanol derived liquid hydrocarbons changes from ~18% to 43%. The remaining light paraffins and olefins can be further converted to valuable BTX products (94% BTX in the liquid) over Ga-ZSM-5 at 500 C. Thus, the LGR is an effective approach to convert ethanol to liquid hydrocarbons with higher liquid yield and low aromatic content, especially low benzene concentration, which could be blended with gasoline in a much higher ratio than ethanol or ethanol derived hydrocarbon blend-stock.

09 BIOMASS FUELS↗

Direct Observation of Xe and Kr Adsorption in a Xe-Selective Microporous Metal–Organic Framework

The cryogenic separation of noble gases is energy-intensive and expensive, especially when low concentrations are involved. Metal organic frameworks containing polarizing groups within their pore spaces are predicted to be efficient Xe/Kr solid state adsorbents but no experimental insights on the nature of the Xe-network interaction is available to date. Here we report a new microporous metal organic framework (designated SBU2) that is selective toward Xe over Kr at ambient conditions, with Xe/Kr selectivity of about 10 and Xe capacity of 37.1 wt% at 298 K. Results of single crystal diffraction show Xe selectivity may be attributed to the specific geometry of the pores, forming cages built with phenyl rings and enriched with polar -OH groups, both serving as strong adsorption sites for polarizable Xe gas. The Xe/Kr separation in SBU2 was investigated with experimental and computational breakthrough methods. These experiments showed that Xe broke through the column after 3 min, followed by Kr at 4.5 min after injection of gases mixture, which confirmed that SBU2 has a real practical potential for separating Xe from Kr. Computational calculations show that SBU2 capacity and adsorption selectivity is comparable to the best-performing unmodified MOFs such as Ni-MOF-74 or Co Formate.

Xenon, Krypton↗

Electrosorption selectivity of ions from mixtures of electrolytes inside nanopores

Grand canonical Monte Carlo (GCMC) simulations are employed to study the selective electrosorption of ions from a mixture of symmetric and asymmetric electrolytes confined in pores and results are compared to experimental observations obtained via cyclic voltammetry and batch electrosorption equilibrium experiments. GCMC simulations have the advantage over other Monte Carlo methods to unambiguously quantify the total number of ions in the pore solution. The exclusion parameter and selectivity factor are used to evaluate the selective capacity of pores toward different ionic species under various conditions. The number of coions inside the pore solution is determined by the proportion of different counterions present in the double-layer region. Because of the competitive effects resulting from asymmetries in charge and size associated with different ions, the electrosorption selectivity of small monovalent over large divalent counterions first decreases with increasing surface charge, passes through a minimum, and then increases with further increase in surface charge. At low and moderate surface charge densities, the fact that large divalent counterions preferentially screen the surface charge has a strong effect on pore occupancy; whereas at a very high surface charge density, size-exclusion effects dominate and determine the accessibility of different ions into the pores. Therefore, electrosorption selectivity of ions from a mixture of electrolytes could, in principle, be achieved via tuning the electrical double-layer formation inside the pores through the regulation of surface charge tailored for different ion characteristics. The findings of this work provide important information relevant to ion selectivity during separation processes and energy storage in supercapacitors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗