Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineer Shuttle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Probabilistic structural analysis of aerospace components using NESSUS

Probabilistic structural analysis of a Space Shuttle main engine turbopump blade is conducted using the computer code NESSUS (numerical evaluation of stochastic structures under stress). The goal of the analysis is to derive probabilistic characteristics of blade response given probabilistic descriptions of uncertainties in blade geometry, material properties, and temperature and pressure distributions. Probability densities are derived for critical blade responses. Risk assessment and failure life analysis is conducted assuming different failure models.

Shiao, Michael C.↗
NASA NTRS1989

The effects of Reynolds number, rotor incidence angle, and surface roughness on the heat transfer distribution in a large-scale turbine rotor passage

A combined experimental and computational program was conducted to examine the heat transfer distribution in a turbine rotor passage geometrically similiar to the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP). Heat transfer was measured and computed for both the full-span suction and pressure surfaces of the rotor airfoil as well as for the hub endwall surface. The primary objective of the program was to provide a benchmark-quality data base for the assessment of rotor passage heat transfer computational procedures. The experimental portion of the study was conducted in a large-scale, ambient temperature, rotating turbine model. Heat transfer data were obtained using thermocouple and liquid-crystal techniques to measure temperature distributions on the thin, electrically-heated skin of the rotor passage model. Test data were obtained for various combinations of Reynolds number, rotor incidence angle and model surface roughness. The data are reported in the form of contour maps of Stanton number. These heat distribution maps revealed numerous local effects produced by the three-dimensional flows within the rotor passage. Of particular importance were regions of local enhancement produced on the airfoil suction surface by the main-passage and tip-leakage vortices and on the hub endwall by the leading-edge horseshoe vortex system. The computational portion consisted of the application of a well-posed parabolized Navier-Stokes analysis to the calculation of the three-dimensional viscous flow through ducts simulating the a gas turbine passage. These cases include a 90 deg turning duct, a gas turbine cascade simulating a stator passage, and a gas turbine rotor passage including Coriolis forces. The calculated results were evaluated using experimental data of the three-dimensional velocity fields, wall static pressures, and wall heat transfer on the suction surface of the turbine airfoil and on the end wall. Particular attention was paid to an accurate modeling of the passage vortex and to the development of the wall boundary layers including crossflow.

Blair, Michael F.↗
NASA NTRS1990

Rocket combustion chamber life-enhancing design concepts

NASA continues to pursue technologies which can lead to an increase in life and reduce the costs of fabrication of the Space Shuttle Main Engine. The joint NASA/Air Force Advanced Launch System Program has set its prime objectives to be high reliability and low cost for their new advanced booster engine. In order to meet these objectives, NASA will utilize the results of several ongoing programs to provide the required technologies. An overview is presented of those programs which address life enhancing design concepts for the combustion chamber. Seven different design concepts, which reduce the thermal strain and/or increase the material strength of the combustion chamber liner wall are discussed. Subscale rocket test results are presented, where available, for life enhancing design concepts. Two techniques for reducing chamber fabrication costs are discussed, as well as issues relating to hydrocarbon fuels/combustion chamber liner materials compatibility.

Quentmeyer, Richard J.↗
NASA NTRS1990

LOX manifold tee analysis

A 4000 Hz vibration phenomena was observed during the test firings of several space shuttle main engines (SSME). Experimental studies of this phenomena suggest that the problem might be associated with vortex shedding from the vanes within the LOX tee manifold. The objective of this study was to determine the unsteady, 3-D flow associated with these vanes by computational methods to identify and better understand the 4000 Hz vibration phenomena. A flow solver, FDNS, for the turbulent conservation equations was validated for predicting high frequency vortex dynamics and used to predict 2-D and 3-D flows within the LOX tee. 4000 Hz excitation oscillations were predicted for some flows and the entire 3-D flow structure was predicted for LOX tee flow. The complexity of the flow was revealed by this analysis, and computational methods for predicting these high frequency oscillations in future engine systems were established.

Chen, Yen-Sen↗
NASA NTRS1989

The structural dynamics analysis of the main injector LOX inlet tee and its redesign

A ground test of a specially instrumented Space Shuttle Main Engine (SSME) revealed excessively high strains in the high pressure Liquid Oxygen (LOX) inlet line which carries LOX to the Main Injector. The inlet tee acts as a manifold which utilizes two splitter vanes to direct the flow of LOX into the main injector. When the high strains were discovered, it was thought that these splitter vanes, coupled with high energy flow was the source. This resulted not only in high strains in the LOX inlet tee, but excessive vibration at a frequency of 4000 Hz located at the gimbal bearing, and at the main injector. This was later to be known as The 4kHz Phenomenon. The dynamic analysis which was used to predict the response due to the 4kHz phenomenon and the analysis used to aid in the design modification required to the hardware to reduce or eliminate the phenomenon is examined.

Romano, E.↗
NASA NTRS1988

Evolution and use of combined mechanical and thermal codes for cryogenic turbopump bearings

Shaft bearing system analysis codes were developed, improved, and used to investigate Space Shuttle Main Engine (SSME) Liquid Oxygen (LOX) turbopump bearing problems, and to support the Marshall Space Flight Center Bearing and Seal Materials Test (BSMT) program. Thermal network modeling uses the SINDA thermal code, and the modeling of bearing quasi-dynamic characteristics uses the SHABERTH bearing/shaft code. These codes are solved concurrently for a bearing/shaft system using software developed for this purpose. Simulation of the SSME LOX turbopump turbine and pump end bearings and the MSFC BSMT operating in liquid nitrogen (LN sub 2) and LOX was done. The thermal network models include the bearing components, bearing carriers, shaft, housing, frictional heat, and viscous fluid energy. A cage model was included to account for heat generation between the cage and rolling elements. Since most bearing surfaces operate at temperatures well above the coolant saturation temperature, and move at high speed relative to the coolant, forced convection boiling is the dominant mechanism for heat removal. Improved modeling of forced convection film boiling was incorporated to take into account the local vapor generation at the high temperature surfaces. Rearing preloads in the pump and tester are provided by preload springs. As bearing operating clearances and contact angles change due to thermal effects and loading, the bearing preload changes with these varying conditions. These characteristics were modeled and are included in the overall system models. Results from these models indicate an operational limit which, if exceeded, predicts a thermal excursion.

Cody, Joe C.↗
NASA NTRS1988

Cryogenic, high speed, turbopump bearing cooling requirements

Although the Space Shuttle Main Engine (SSME) has repeatedly demonstrated the capability to perform during launch, the High Pressure Oxidizer Turbopump (HPOTP) main shaft bearings have not met their 7.5 hour life requirement. A tester is being employed to provide the capability of subjecting full scale bearings and seals to speeds, loads, propellants, temperatures, and pressures which simulate engine operating conditions. The tester design permits much more elaborate instrumentation and diagnostics than could be accommodated in an SSME turbopump. Tests were made to demonstrate the facilities; and the devices' capabilities, to verify the instruments in its operating environment and to establish a performance baseline for the flight type SSME HPOTP Turbine Bearing design. Bearing performance data from tests are being utilized to generate: (1) a high speed, cryogenic turbopump bearing computer mechanical model, and (2) a much improved, very detailed thermal model to better understand bearing internal operating conditions. Parametric tests were also made to determine the effects of speed, axial loads, coolant flow rate, and surface finish degradation on bearing performance.

Dolan, Fred J.↗
NASA NTRS1988

Bearing optimization for SSME HPOTP application

The space shuttle main engine (SSME) high-pressure oxygen turbopumps (HPOTP) have not experienced the service life required of them. To improve the life of the existing turbopump bearings, modifications to the bearings that could be retrofitted into the present bearing cavity are being investigated. Several bearing parameters were optimized using the computer program SHABERTH, which performs a thermomechanical simulation of a load support system. The computer analysis showed that improved bearing performance is feasible if low friction coefficients can be attained. Bearing geometries were optimized considering heat generation, equilibrium temperatures, and relative life. Two sets of curvatures were selected from the optimization: an inner-raceway curvature of 0.54, an outer-raceway curvature of 0.52, and an inner-raceway curvature of 0.55, an outer-raceway curvature of 0.53. A contact angle of 16 deg was also selected. Thermal gradients through the bearings were found to be lower with liquid lubrication than with solid film lubrication. As the coolant flowrate through the bearing increased, the ball temperature decreased but at a continuously decreasing rate. The optimum flowrate was approximately 4 kg/s. The analytical modeling used to determine these feasible modifications to improve bearing performance is described.

Armstrong, Elizabeth S.↗
NASA NTRS1988

Cage stability analysis for SSME HPOTP bearings

A numerical model of cage motion (CAGEDYN) was used to analyze the stability of bearing cages in the Space Shuttle main engine (SSME) high pressure oxygen turbopump (HPOTP). The stability of existing bearing geometries, as well as perturbations of these geometries, was analyzed for various operating conditions. Results of the analyses show that some combinations of operating parameters, exacerbated by the sparse lubrication that exist in the HPOTP bearings, can cause unstable cage oscillations. Frequencies of cage oscillations were predicted by the CAGEDYN numerical model by Fourier analysis of predicted cage motions. Under conditions that cause unstable cage motion, high frequency oscillations were predicted that could cause premature cage failures.

Merriman, T. L.↗
NASA NTRS1988

Rocketdyne LOX bearing tester program

The cause, or causes, for the Space Shuttle Main Engine ball wear were unknown, however, several mechanisms were suspected. Two testers were designed and built for operation in liquid oxygen to empirically gain insight into the problems and iterate solutions in a timely and cost efficient manner independent of engine testing. Schedules and test plans were developed that defined a test matrix consisting of parametric variations of loading, cooling or vapor margin, cage lubrication, material, and geometry studies. Initial test results indicated that the low pressure pump thrust bearing surface distress is a function of high axial load. Initial high pressure turbopump bearing tests produced the wear phenomenon observed in the turbopump and identified an inadequate vapor margin problem and a coolant flowrate sensitivity issue. These tests provided calibration data of analytical model predictions to give high confidence in the positive impact of future turbopump design modification for flight. Various modifications will be evaluated in these testers, since similar turbopump conditions can be produced and the benefit of the modification will be quantified in measured wear life comparisons.

Keba, J. E.↗
NASA NTRS1988

Micromechanics of cyclic deformation in SSME turbopump blade materials

Current and candidate Space Shuttle Main Engine (SSME) turbopump blade materials are anisotropic, both in their elastic and plastic response. The major objective is to characterize the plastic deformation behavior of a typical single crystal nickel-base superalloy, PWA 1480, and to use this information to help guide the development of anisotropic constitutive models.

Milligan, Walter W.↗
NASA NTRS1988

A comparison of single-cycle versus multi-cycle proof testing strategies

Proof testing was a useful supplement to conventional nondestructive evaluation (NDE) of space shuttle main engine (SSME) components. Since many of these components involve thin sections and high toughness materials, such as Inconel 718, conventional single-cycle proof test logic is not applicable due to the propensity for stable crack growth during the proof tests. Experience with five-cycle proof testing of SSME components is summarized and a framework is outlined for understanding multi-cycle proof testing using the fracture mechanics concept of a resistance curve. Extreme value statistics are also used to propose an empirical approach to compare the advantages and disadvantages of single- versus multi-cycle proof testing. The importance of the initial flaw size distribution and specimen thickness in such a comparison is also discussed.

Hudak, Stephen J., Jr.↗
NASA NTRS1988

Probabilistic model for fracture mechanics service life analysis

The service longevity of complex propulsion systems, such as the Space Shuttle Main Engine (SSME), can be at risk from several competing failure modes. Conventional life assessment practice focuses upon the most severely life-limited feature of a given component, even though there may be other, less severe, potential failure locations. Primary, secondary, tertiary failure modes, as well as their associated probabilities, must also be considered. Futhermore, these probabilities are functions of accumulated service time. Thus a component may not always succumb to the most severe, or even the most probable failure mode. Propulsion system longevity must be assessed by considering simultaneously the actions of, and interactions among, life-limiting influences. These include, but are not limited to, high frequency fatigue (HFF), low cycle fatigue (LCF), and subsequent crack propagation, thermal and acoustic loadings, and the influence of less-than-ideal nondestructive evaluation (NDE). An outline is provided for a probabilistic model for service life analysis, and the progress towards its implementation is reported.

Annis, Charles↗
NASA NTRS1988

Durability of thermal barrier coatings in a high heat flux environment

Thermal shock is a significant factor in the limited service life of Space Shuttle Main Engine (SSME) high pressure, fuel turbopump (HPFTP) turbine blades. Addition of advanced thermal barrier coatings (TBCs) to the blades could serve to dampen the thermal shock, thereby increasing the life of the blades. However, testing and use of TBCs to date is performed primarily under moderate heat flux conditions which are typical of aircraft turbines. Only limited testing was conducted that addresses high heat flux and severe thermal shock conditions. Therefore, it is not clear if TBCs can survive severe thermal shocks or provide adequate thermal shock protection to the HPFTP turbine blades. The purpose is to experimentally evaluate the potential durability and protective capability of a variety of advanced TBCs in a cyclic thermal shock environment. A secondary goal is to identify significant parameters affecting TBC life during high heat flux testing. Parameters investigated include top coat thickness, bond coat thickness, substrate type, and substrate geometry.

Brindley, William J.↗
NASA NTRS1988

Vacuum application of thermal barrier plasma coatings

Coatings are presently applied to Space Shuttle Main Engine (SSME) turbine blades for protection against the harsh environment realized in the engine during lift off-to-orbit. High performance nickel, chromium, aluminum, and yttrium (NiCrAlY) alloy coatings, which are applied by atmospheric plasma spraying, crack and spall off because of the severe thermal shock experienced during start-up and shut-down of the engine. Ceramic coatings of yttria stabilized zirconia (ZrO2-Y2O3) were applied initially as a thermal barrier over coating to the NiCrAlY but were removed because of even greater spalling. Utilizing a vacuum plasma spraying process, bond coatings of NiCrAlY were applied in a low pressure atmosphere of argon/helium, producing significantly improved coating-to-blade bonding. The improved coatings showed no spalling after 40 MSFC burner rig thermal shock cycles, cycling between 1700 and -423 F. The current atmospheric plasma NiCrAlY coatings spalled during 25 test cycles. Subsequently, a process was developed for applying a durable thermal barrier coating of ZrO2-Y2O3 to the turbine blades of first stage high-pressure fuel turbopumps utilizing the vacuum plasma process. The improved thermal barrier coating has successfully passed 40 burner rig thermal shock cycles without spalling. Hot firing in an SSME turbine engine is scheduled for the blades. Tooling was installed in preparation for vacuum plasma spray coating other SSME hardware, e.g., the titanium main fuel valve housing (MFVH) and the fuel turbopump nozzle/stator.

Holmes, R. R.↗
NASA NTRS1988

Ceramic matrix composites in simulated SSME environments

Future Space Shuttle Main Engine (SSME)-type rocket engines can benefit from the use of fiber-reinforced ceramix matrix composites (FRCMC). Ceramics reinforced with long continuous fibers exhibit improved tolerance to severe thermomechanical and environmental exposures. An in-house NASA-Lewis program to evaluate the durability of FRCMC in simulated SSME environments is described. Primary tests involve multiple (one second) exposures of FRCMC specimens in a hydrogen/oxygen rocket test rig. This rig generates surface heating rates of 1000 to 2500 C/second. The FRCMC durability evaluation involves measurement of retained strength as a function of thermal shock severity and number of upshock cycles. Preliminary test results for monolithic silicon nitride (Si3N4) and silicon carbide (SiC), and one type of silicon based FRCMC, are presented. The test data are examined in terms of simple thermal shock theory.

Herbell, Thomas P.↗
NASA NTRS1988

Turbomachinery rotor forces

The fluid-induced forces, both steady and unsteady, acting upon an impeller of a centrifugal pump, and impeller blade-diffuser vane interaction in centrifugal pumps with vaned radial diffusers were evaluated experimentally and theoretically. Knowledge of the steady and unsteady forces, and the associated rotordynamic coefficients are required to effectively model the rotor dynamics of the High Pressure Fuel Turbopump (HPFTP) of the Space Shuttle Main Engine (SSME). These forces and rotordynamic coefficients were investigated using different impellers in combination with volutes and vaned diffusers, and axial inducers. These rotor forces are global. Local forces and pressures are also important in impeller-diffuser interaction, for they may cause cavitation damage and even vane failures. Thus, in a separate investigation, impeller wake, and impeller blade and diffuser vane pressure measurements were made. The nature of the rotordynamic forces is discussed, the experimental facility is described, and the measurements of unsteady forces and pressure are reported together with a brief and incomplete attempt to calculate these flows.

Arndt, Norbert↗