Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Serpentine metal gasket

A metallic seal or gasket for use in the joining of cryogenic fluid conduits, the seal or gasket having a generally planar and serpentine periphery defining a central aperture. According to a preferred embodiment, the periphery has at least two opposing elongated serpentine sides and two opposing arcuate ends joining the opposing elongated serpentine sides and is of a hexagonal cross-section.

42 ENGINEERING↗

Characterization of High Strain Rate Mechanical behavior of AZ31 magnesium alloy using 3D Digital Image Correlation

Characterization of the material mechanical behavior at sub-Hopkinson regime (0.1 to 1000 s{sup -1}) is very challenging due to instrumentation limitations and the complexity of data analysis involved in dynamic loading. In this study, AZ31 magnesium alloy sheet specimens are tested using a custom designed servo-hydraulic machine in tension at nominal strain rates up to 1000 s{sup -1}. In order to resolve strain measurement artifacts, the specimen displacement is measured using 3D Digital Image correlation instead from actuator motion. The total strain is measured up to {approx} 30%, which is far beyond the measurable range of electric resistance strain gages. Stresses are calculated based on the elastic strains in the tab of a standard dog-bone shaped specimen. Using this technique, the stresses measured for strain rates of 100 s{sup -1} and lower show little or no noise comparing to load cell signals. When the strain rates are higher than 250 s{sup -1}, the noises and oscillations in the stress measurements are significantly decreased from {approx} 250 to 50 MPa. Overall, it is found that there are no significant differences in the elongation, although the material exhibits slight work hardening when the strain rate is increased from 1 to 100 s{sup -1}.

36 MATERIALS SCIENCE↗

Multiaxial deformation of polyethylene and polyethylene/clay nanocomposites: In situ synchrotron small angle and wide angle X-ray scattering study

A unique in situ multiaxial deformation device has been designed and built specifically for simultaneous synchrotron small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS) measurements. SAXS and WAXS patterns of high-density polyethylene (HDPE) and HDPE/clay nanocomposites were measured in real time during in situ multiaxial deformation at room temperature and at 55 C. It was observed that the morphological evolution of polyethylene is affected by the existence of clay platelets as well as the deformation temperature and strain rate. Martensitic transformation of orthorhombic into monoclinic crystal phases was observed under strain in HDPE, which is delayed and hindered in the presence of clay nanoplatelets. From the SAXS measurements, it was observed that the thickness of the interlamellar amorphous region increased with increasing strain, which is due to elongation of the amorphous chains. The increase in amorphous layer thickness is slightly higher for the nanocomposites compared to the neat polymer.

36 MATERIALS SCIENCE↗

Microstructural Effects on SCC Initiation PWR Primary Water Cold-Worked Alloy 600

SCC initiation behavior of one mill annealed alloy 600 plate heat was investigated in simulated PWR primary water under constant load at yield stress with in-situ direct current potential drop (DCPD) monitoring for crack initiation. Twelve specimens were tested at similar cold work levels among which three showed much shorter SCC initiation times (<400 hrs) than the others (>1200 hrs). Post-test examinations revealed that these three specimens all feature an inhomogeneous microstructure where the primary crack always nucleated along the boundary of large elongated grains protruding normally into the gauge. In contrast, such microstructure was either not observed or did not extend deep enough into the gauge in the other specimens exhibiting ~3-6X longer initiation times. In order to better understand the role of this microstructural inhomogeneity in SCC initiation, high-resolution microscopy was performed to compare carbide morphology and strain distribution between the long grains and normal grains, and their potential effects on SCC initiation are discussed in this paper.

Alloy 600↗

Structure-activity relationship for vanilloid compounds from extract of Zingiber officinale var rubrum rhizomes: effect on extracellular melanogenesis inhibitory activity

The components in the methanol extract of Zingiber officinale var rubrum (red ginger) were isolated by a series of column chromatography and identified by Nuclear Magnetic Resonance (NMR) and Matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOFMS). Thirteen components, including eleven vanilloid compounds, were isolated from the extract. All the isolated components reduced extracellular melanin contents. Structure-activity relationship studies suggested that elongation of the carbon chain of shogaol and gingerol increased the extracellular melanogenesis inhibitory activity, and that the carbonyl and hydroxyl groups on the carbon chain in gingerol played an important role in this effect. In order to reveal the importance of the vanillyl group for the melanogenesis inhibitory activity, 6-gingerol (1) and 6-shogaol (5), which were the main compounds in the extract, were glucosylated and their effects were evaluated. The glucosylated 6-shogaol resulted in improved melanogenesis inhibitory activity, while the glucosylated 6-gingerol had no such effect. These results indicated different mechanisms for the melanogenesis inhibitory activity of the two vanilloid compounds.

60 APPLIED LIFE SCIENCES↗

Direct Numerical Simulation of Surfactant-Stabilized Emulsions Morphology and Shear Viscosity in Starting Shear Flow

A 3D lattice Boltzmann model for two-phase flow with amphiphilic surfactant was used to investigate the evolution of emulsion morphology and shear stress in starting shear flow. The interfacial contributions were analyzed for low and high volume fractions and varying surfactant activity. A transient viscoelastic contribution to the emulsion rheology under constant strain rate conditions was attributed to the interfacial stress. For droplet volume fractions below 0.3 and an average capillary number of about 0.25, highly elliptical droplets formed. Consistent with affine deformation models, gradual elongation of the droplets increased the shear stress at early times and reduced it at later times. Lower interfacial tension with increased surfactant activity counterbalanced the effect of increased interfacial area, and the net shear stress did not change significantly. For higher volume fractions, co-continuous phases with a complex topology were formed. The surfactant decreased the interfacial shear stress due mainly to advection of surfactant to higher curvature areas. Our results are in qualitative agreement with experimental data for polymer blends in terms of transient interfacial stresses and limited enhancement of the emulsion viscosity at larger volume fractions where the phases are co-continuous.

99 GENERAL AND MISCELLANEOUS↗

Interactive Influence of Biofiber Composition and Elastomer on Physico-Mechanical Properties of PLA Green Composites

The objective of this work was to improve the impact and thermal properties of polylactic acid (PLA)-based biocomposite by appropriate application of cellulosic fiber and a bioelastomer. Biocomposites formulations with fiber contents of up to 20% in combination with a bioelastomer were extrusion-compounded in a twin-screw extruder followed by molding in an injection molding system. Fibers used in the formulations included three types of cellulosic fiber; namely, raw fiber from oat hull biomass (RF), hydrolysis byproduct (ATF) which was the solid fraction obtained from an acid-catalyzed hydrolysis of RF, and delignified fibers (AD30, AD65, AD100) which were the products of delignification of ATF. Formulated biocomposites were characterized for thermal (glass transition and melting temperatures, and enthalpy of melting) and physico-mechanical (tensile and bending strengths, stiffness, impact energy, and water absorption) properties. Among all types of biofibers, RF resulted in poor properties in the biocomposites due to the high hemicellulose content in the structure. On the other hand, the ratio of lignin to cellulose (in the absence of hemicellulose) in the modified fibers did not significantly affect the physico-mechanical and thermal properties of the biocomposites. The elastomer applied in the formulations improved the impact energy, thermal properties, and elongation at break of the composites. However, it adversely affected the strength and water resistance of biocomposites, especially in the presence of hemicellulose. The results indicated that, depending on the application, a wide range of PLA green composites with different physico-mechanical properties can be achieved.

09 BIOMASS FUELS↗

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO{sub 2} Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO{sub 2} composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO{sub 2} composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO{sub 2} (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO{sub 2} composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m{sup 2}. PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.

36 MATERIALS SCIENCE↗

A Novel Environmentally Compatible Bio-Based Product from Gelatin and Natural Rubber: Physical Properties

The objective of the present work was to study the preparation of a novel bio-based product from gelatin (GT) and natural rubber (NR) using potassium persulphate (KPS) as an initiator. The GT and NR composites (GT/NR composites) containing KPS were formed in an aqueous latex solution. The chemical structure of the GT/NR composite was characterized by ATR-FTIR, and XRD. The highest tensile strength was observed in a 9/1 GT/NR composite and the elongation at break of this composite was improved by the addition of both NR and glycerol. In addition, the swelling ratio increased as a function of increasing GT content in the composite. The thermal stability of the GT was improved after the formation of the chemical interaction between the NR and GT helped by the KPS. The best ratio of the GT/NR composite was 3/7 GT/NR. This environmentally friendly composite easily decomposed in natural soil within 30 days. The novel biopolymer showed high mechanical properties, water resistance and was produced in an environmentally compatible process. The NR was able to improve some of the physical and mechanical properties of GT biofilms produced from the composite. Possible future applications of this composite are for medical materials, and the packaging and life extension of food products.

36 MATERIALS SCIENCE↗

Multiple Reprocessing Cycles of Corn Starch-Based Biocomposites Reinforced with Curauá Fiber

Biocomposites with a corn starch-based biodegradable polymer as matrix and 10 wt% vegetable curauá fiber were processed by injection molding and were submitted to reprocessing up to ten cycles with or without 3 wt% of maleic anhydride grafted polypropylene as coupling agent. The effect of reprocessing on hardness, impact and tensile properties as well as on the morphology, thermal properties, chemical structure and soil degradation behaviour of the matrix and biocomposites was evaluated. Curauá fibers have increased hardness, impact and tensile strengths as well as increased tensile modulus and decreased elongation at break of the biocomposites with respect to starch-based matrix and these properties slightly decreased or no considerable changes were observed with the reprocessing cycle increase. The addition of coupling agent promoted an increase in all properties and they remained almost constant with the reprocessing cycle increase. Thus, the incorporation of curauá fiber within starch-based matrix can improve the mechanical properties of the biocomposites which showed potential to be recycled despite the weight loss in soil degradation tests reached around 10 wt% after 230 days for biocomposites reprocessed ten cycles.

36 MATERIALS SCIENCE↗

Copolymer P(BS-co-LA) Enhanced Compatibility of PBS/PLA Composite

The copolymer P(BS-co-LA) with various block chains are synthesized and employed as the interface linker in poly(butyl succinate) (PBS)/polylactic acid (PLA) blends to enhance the compatibility of PBS and PLA. The crystallization and rheological properties are determined by various methods, as well as the mechanical properties. The results indicate that the addition of P(BS-co-LA) decreases the crystallization temperature and degree of crystallinity in the PBS/PLA composite. The P(BS-co-LA) with a long-block chain remarkably enhances the compatibility of PBS/PLA composites than short block chains, and the PBS/PLA/P(BS-hb-LA) composites show great elongation at break and impact strength. Besides, the crystallinity and the rate of crystallization are increased, which are also observed by the X-ray diffraction. All approaches lead to the same result that P(BS-co-LA) with the long block chain is an excellent compatibility agent to enhance mechanical properties of the PBS/PLA composites.

36 MATERIALS SCIENCE↗

PVA Based Ternary Nanocomposites with Enhanced Properties Prepared by Using a Combination of Rice Starch Nanocrystals and Silver Nanoparticles

Ternary nanocomposite films exhibiting better properties were prepared by incorporating two different nanoparticles such as rice starch nanocrystals (RSN) and silver nanoparticles (AgNPs) together in polyvinyl alcohol (PVA) matrix at various concentrations. The morphological evaluation using atomic force microscopy revealed that the particle size of RSN nanoparticles varied from 50 to 125 nm. The nanocomposite films made using these nanoparticles were evaluated for its chemical, mechanical and thermal properties. FTIR spectra of the films revealed some specific vibrational bands of RSN along with the characteristic bands of PVA. The mechanical property analysis of nanocomposite films indicated better tensile strength and elongation properties, which can be attributed to the strong interaction of PVA with RSN and AgNPs. The thermal properties of these films were also evaluated. These ternary nanocomposites exhibited superior mechanical properties, which is very much beneficial as far as the end use applications are concerned.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of Compatibilizer and Thermoplastic Starch (TPS) Concentration on Morphological, Rheological, Tensile, Thermal and Moisture Sorption Properties of Plasticized Polylactic Acid/TPS Blends

The blends of polylactic acid plasticized with acetyl tributyl citrate (P-PLA) and thermoplastic wheat starch (TPS) were prepared by a co-rotating twin screw extruder and the effect of maleic anhydride grafted PLA (PLA-g-MA) content as reactive compatibilizer on blends compatibility through morphological, rheological and tensile properties of the blends was investigated. Considerable improvement in properties of P-PLA/TPS (70/30 w/w) blend with incorporating the optimum PLA-g-MA content of 4 phr was achieved as this blend exhibited better morphological and rheological properties with an increase by 158 and 276% in tensile strength and elongation at break, respectively, compared to the uncompatibilized blend. Also the thermal stability and moisture sorption properties of the blends as effected by TPS content were studied. Decreasing in thermal stability and increasing in equilibrium moisture content of the blends were observed with progressively increasing of TPS content. For prediction the moisture sorption behaviour of blends with various TPS contents at different relative humidity, the moisture sorption isotherm data were modeled by GAB (Guggenheim–Anderson–de Boer) model.

36 MATERIALS SCIENCE↗

Fabrication and Characterization of Poly(lactic acid) Biocomposites Reinforced by Calcium Sulfate Whisker

The biodegradable poly(lactic acid) (PLA) composites filled with calcium sulfate whisker (CSW) were fabricated via melt-blending and subsequent injection molding. Surface organification of γ-aminopropyltriethoxysilane (APTES) on CSW was applied to accelerate the wettability of PLA to CSW. The mechanical properties, morphological structures, crystallization behaviors and thermal stabilities of PLA/CSW composites were investigated in detail. Results showed that modification of APTES changed the surface morphologies and element compositions, helping to form the well bonded interfaces. By adding CSW, the elastic modulus of PLA/CSW composites presented a sustained increment, while tensile strength, elongation at break and impact toughness were increased first and then decreased. The presence of CSW impeded the melt-crystallization but accelerated the cold-crystallization process. On the whole, the actual crystallinity for the composites was suppressed except for the case with 20% CSW. The thermal stability was enhanced by CSW as expected, and all the samples showed the exact same reaction order (n = 1) according to Carrasco method. Nevertheless, the activation energies were declined, indicating CSW was in favor of thermal decomposition of PLA phases. Finally, it was interestingly found that CSW could improve the comprehensive properties of PLA without deteriorating the processibility.

36 MATERIALS SCIENCE↗

Effect of Natural Glyceryl Tributyrate as Plasticizer and Compatibilizer on the Performance of Bio-Based Polylactic Acid/poly(3-hydroxybutyrate) Blends

Bio-based poly(lactic acid)/poly(3-hydroxybutyrate) (PLA/PHB) films were melt-blended with a natural hydrophobic plasticizer (glyceryl tributyrate, TB) at three different concentrations (10, 15 and 20% by weight per 100 parts of the blends) to study the effect of TB on the final properties of the materials. The pursued aim was to obtain a material with potential use in the packaging industry. Two different PLA/PHB ratios were used, 70/30 and 60/40, respectively. A full characterization of the developed blends was carried out, including the morphological, thermal, mechanical and barrier properties. The thermal test revealed the immiscibility between PLA and PHB by showing two glass transition temperatures for the blends and biphasic melt. Mechanical tests showed the increased in the elongation at break as the plasticizer content in films increased. The incorporation of PHB crystals in the PLA matrix displayed an improvement in the water barrier properties of materials. Finally, formulations PLA/PHB-TB with 15 wt% of plasticizer presented the best combination of properties suitable for the intended use in films manufacturing, showing toughness and ductility, good water barrier properties and transparency with slightly amber color.

36 MATERIALS SCIENCE↗

Micro Crystalline Bamboo Cellulose Based Seaweed Biodegradable Composite Films for Sustainable Packaging Material

This study is aimed to fabricate and characterize the seaweed- biodegradable films incorporated with varying concentrations of microcrystalline cellulose (MCC) which was extracted from two bamboo sources: Schizostachyum brachycladum (BLMCC) and Gigantochloa scortechinii (BSMCC). Pure biodegradable seaweed film was directly fabricated from red seaweed (Kappaphycus alvarezii). In this demonstrated work, commercial MCC (CMCC), BLMCC and BSMCC were used to reinforce the pure seaweed bio-degradable film at different loading concentrations (0, 1, 3, 5, 7, 10 and 15%) based on the dried-weight of seaweed, for packaging applications. There was substantial improvement in the tensile strength and contact angle values while reduction in the water vapor permeability and elongation at break values with the incorporation of the CMCC, BLMCC and BSMCC into the seaweed pure film matrix, which is highly desirable for the packaging material in the current scenario. The morphology of the fabricated films confirmed that there was good dispersion of the 7% of CMCC, 5% of BLMCC and 3% of BSMCC in the pure seaweed films, which resulted in the enhanced mechanical properties. So far, this is the first report on the microcrystalline cellulose based seaweed films with excellent mechanical properties, which makes them suitable for packaging application. The demonstrated work proved that both BSMCC and BLMCC based seaweed composite films have the huge potential to be used as biodegradable packaging material for wide range of applications. Graphical Abstract: .

36 MATERIALS SCIENCE↗

Hopes Beyond PET Recycling: Environmentally Clean and Engineeringly Applicable

Disposal of plastics in the environment has become a core of anxiety in developing countries, while in the developed countries the focus has additionally been placed on design and manufacture of emerging products from plastic wastes—a somewhat vague yet promising horizon. Central to environmental concerns are poly(ethylene terephthalate) (PET) wastes, mainly from post-consumer bottles. Because of a considerable drop in molecular weight in the course of recycling, recycled PETs are not suitable for engineering uses. An efficient yet reasonably green synthesis route is employed here to convert PET wastes into polyurethane, and then carbon nanotubes (CNTs) was added at different levels to obtain nanocomposites with high mechanical properties. The effects of isocyanate (NCO)/hydroxyl (OH) molar ratio and CNTs content on the morphology, physical and mechanical properties were discussed. Chemical/physical crosslink density was calculated from initial slope of stress–strain curves, Mooney–Rivlin plots, strain-hardening modulus, rubbery-plateau storage modulus and swelling data. High tensile strength (300 MPa) and breaking elongation (160%) of polyurethane/CNTs nanocomposites born from PET wastes seemed promising. Microscopic analyses by AFM, SEM, and TEM gave useful information about distribution of CNTs in polyurethane. Lastly, structural changes were correlated to mechanical properties improvement.

36 MATERIALS SCIENCE↗

Thermal, Mechanical Properties and Rheological Behavior of Poly(Propylene Carbonate)/Poly(Ethylene Glycol)/Graphene Oxide Nanocomposites

Graphene oxide (GO) is an efficient nanofiller for polymers and a good dispersion of GO in polymer matrix is most important to enhance properties. Poly(propylene carbonate) (PPC)/GO nanocomposite was prepared by a method with solution blending and melt mixing for improvement of GO dispersion. First, GO was prepared using an improved Hummers method. In the solution blending, GO was well dispersed in water and another low molecular weight polymer, poly(ethylene glycol) (PEG), was also dispersed in water, as a dispersion medium for next melt mixing of PPC and GO. Then PPC and PEG/GO was melt-mixed in a HAAKE mixer. The dispersion of GO in PPC matrix and effect of GO content on properties of PPC/PEG/GO nanocomposites was investigated. Results show that tensile strength of nanocomposites with the content of 0.5 wt% GO increased from 17.51 MPa (pure PPC) to 21.61 MPa and elongation at break can be kept high. The complex viscosity, storage and loss modulus is the highest for nanocomposites with the content of 0.5 wt% GO. This illustrated that a lower content of GO can improve the properties of PPC, owing to the good dispersion of GO in PPC matrix. Based on dispersion of GO and chemical structure of PPC, PEG, and GO, the reinforcement mechanism of GO in PPC was analyzed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗