Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Plotting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Experimental and analytical investigations of fuselage modal characteristics and structural-acoustic coupling

Measurements conducted on a DC-9 aircraft test section to define the shell and cavity modes of the fuselage, understand its structural-acoustic coupling characteristics, and measure its response to different types of acoustic and vibration excitations are reported. The data were processed to generate spatial plots and wavenumber maps of the shell acceleration and cabin acoustic pressure field. Analysis and interpretation of the spatial plots and wavenumber maps showed that the only structural-acoustic coupling occurred at 105 Hz between the N=2 circumferential structural mode and the (n=2, p=0) circumferential cavity mode. The fuselage response to vibration excitation was found to be dominated by modes whose order increases with frequency.

Simpson, Myles A.↗
NASA NTRS1993

Design of a recovery system for a reentry vehicle

Engineers are often required to design decelerator systems which are deployed in cross-wind orientations. If the system is not designed to minimize 'line sail', damage to the parachutes could result. A Reentry Vehicle Analysis Code (RVAC) and an accompanying graphics animation software program (DISPLAY) are presented in this paper. These computer codes allow the user to quickly apply the Purvis line sail modeling technique to any vehicle and then observe the relative motion of the vehicle, nose cap, suspension lines, pilot and drogue bags and canopies on a computer screen. Data files are created which allow plots of velocities, spacial positions, and dynamic pressures versus time to be generated. The code is an important tool for the design engineer because it integrates two degrees of freedom (DOF) line sail equations with a three DOF model of the reentry body and jettisoned nose cap to provide an animated output.

Von Eckroth, Wulf↗
NASA NTRS1950

Preliminary analysis of problem of determining experimental performance of air-cooled turbine III : methods for determining power and efficiency

Suggested formula are given for determining air-cooled turbine-performance characteristics, such as power and efficiency, as functions of certain parameters. These functions, generally being unknown, are determined from experimental data obtained from specific investigations. Special plotting methods for isolating the effect of each parameter are outlined.

Ellerbrock, Herman H , Jr↗
NASA NTRS1952

Internal-liquid-film-cooling Experiments with Air-stream Temperatures to 2000 Degrees F. in 2- and 4-inch-diameter Horizontal Tubes

Report presents the results of an investigation conducted to determine the effectiveness of liquid-cooling films on the inner surfaces of tubes containing flowing hot air. Experiments were made in 2- and 4-inch-diameter straight metal tubes with air flows at temperatures from 600 degrees to 2000 degrees F. and diameter Reynolds numbers from 2.2 to 14 x 10(5). The film coolant, water, was injected around the circumference at a single axial position on the tubes at flow rates from 0.02 to .24 pound per second per foot of tube circumference (0.8 to 12 percent of the air flow). Liquid-coolant films were established and maintained around and along the tube wall in concurrent flow with the hot air. The results indicated that, in order to film cool a given surface area with as little coolant flow as possible, it may be necessary to limit the flow of coolant introduced at a single axial position and to introduce it at several axial positions. The flow rate of inert coolant required to maintain liquid-film cooling over a given area of tube surface can be estimated when the gas-flow conditions are known by means of a generalized plot of the film-cooling data.

Kinney, George R↗
NASA NTRS1992

The IDL astronomy user's library

IDL (Interactive Data Language) is a commercial programming, plotting, and image display language, which is widely used in astronomy. The IDL Astronomy User's Library is a central repository of over 400 astronomy-related IDL procedures accessible via anonymous FTP. The author will overview the use of IDL within the astronomical community and discuss recent enhancements at the IDL astronomy library. These enhancements include a fairly complete I/O package for FITS images and tables, an image deconvolution package and an image mosaic package, and access to IDL Open Windows/Motif widgets interface. The IDL Astronomy Library is funded by NASA through the Astrophysics Software and Research Aids Program.

Landsman, W. B.↗
NASA NTRS1994

PATRAN 2.5/EAL interface guide

The PATRAN/EA interface guide describes two programs, EALPAT and PATEAL. EALPAT reads an EAL LO1 file and translates the model and results into a PATRAN 2.5 neutral file, element results file, and nodal results file. An EAL model can be color coded in PATRAN, and geometry, loads, boundary conditions, section and material properties, rigid masses, springs, and beam orientations can be plotted and debugged. EAL results can be brought into PATRAN as element or nodal quantities and displayed as deformed plots, animated shapes, color coded elements, or color filled contour plots. PATEAL converts a PATRAN 2.5 data base into an EAL runstream. Geometry, including all element types, alternate coordinate systems, material properties, section properties, loads and boundary conditions are all converted. EALPAT and PATEAL can also be used together with the PATNAS translator from PDA Engineering to convert an EAL runstream to an MSC/NASTRAN bulk data file.

Feldhaus, Winifred S.↗
NASA NTRS1994

Empirical Modeling of Plant Gas Fluxes in Controlled Environments

As humans extend their reach beyond the earth, bioregenerative life support systems must replace the resupply and physical/chemical systems now used. The Controlled Ecological Life Support System (CELSS) will utilize plants to recycle the carbon dioxide (CO2) and excrement produced by humans and return oxygen (O2), purified water and food. CELSS design requires knowledge of gas flux levels for net photosynthesis (PS(sub n)), dark respiration (R(sub d)) and evapotranspiration (ET). Full season gas flux data regarding these processes for wheat (Triticum aestivum), soybean (Glycine max) and rice (Oryza sativa) from published sources were used to develop empirical models. Univariate models relating crop age (days after planting) and gas flux were fit by simple regression. Models are either high order (5th to 8th) or more complex polynomials whose curves describe crop development characteristics. The models provide good estimates of gas flux maxima, but are of limited utility. To broaden the applicability, data were transformed to dimensionless or correlation formats and, again, fit by regression. Polynomials, similar to those in the initial effort, were selected as the most appropriate models. These models indicate that, within a cultivar, gas flux patterns appear remarkably similar prior to maximum flux, but exhibit considerable variation beyond this point. This suggests that more broadly applicable models of plant gas flux are feasible, but univariate models defining gas flux as a function of crop age are too simplistic. Multivariate models using CO2 and crop age were fit for PS(sub n), and R(sub d) by multiple regression. In each case, the selected model is a subset of a full third order model with all possible interactions. These models are improvements over the univariate models because they incorporate more than the single factor, crop age, as the primary variable governing gas flux. They are still limited, however, by their reliance on the other environmental conditions under which the original data were collected. Three-dimensional plots representing the response surface of each model are included. Suitability of using empirical models to generate engineering design estimates is discussed. Recommendations for the use of more complex multivariate models to increase versatility are included.

Cornett, Jessie David↗
NASA NTRS2006

Measurement of Flow Pattern Within a Rotating Stall Cell in an Axial Compressor

Effective active control of rotating stall in axial compressors requires detailed understanding of flow instabilities associated with this compressor regime. Newly designed miniature high frequency response total and static pressure probes as well as commercial thermoanemometric probes are suitable tools for this task. However, during the rotating stall cycle the probes are subjected to flow direction changes that are far larger than the range of probe incidence acceptance, and therefore probe data without a proper correction would misrepresent unsteady variations of flow parameters. A methodology, based on ensemble averaging, is proposed to circumvent this problem. In this approach the ensemble averaged signals acquired for various probe setting angles are segmented, and only the sections for probe setting angles close to the actual flow angle are used for signal recombination. The methodology was verified by excellent agreement between velocity distributions obtained from pressure probe data, and data measured with thermoanemometric probes. Vector plots of unsteady flow behavior during the rotating stall regime indicate reversed flow within the rotating stall cell that spreads over to adjacent rotor blade channels. Results of this study confirmed that the NASA Low Speed Axial Compressor (LSAC) while in a rotating stall regime at rotor design speed exhibits one stall cell that rotates at a speed equal to 50.6 percent of the rotor shaft speed.

Lepicovsky, Jan↗
NASA NTRS2018

The Evolution of Gridded NUCAPS: An Overview of Research to Operations Activities

The next-generation S-NPP and NOAA-20 Cross-track Infrared Sounder (CrIS) temperature and moisture profiles can provide valuable observations; (1) Where conventional radiosonde observations are sparse, (2) Between radiosonde launches. CrIS observations are combined with the Advanced Technology Microwave Sounder (ATMS) to produce high quality vertical soundings in clear and partly cloudy conditions. NUCAPS (NOAA Unique Combined Atmospheric Processing System) is the operational algorithm for processing combined hyperspectral infrared and microwave measurements. NUCAPS Soundings are operationally available in AWIPS as Skew-T plots. The capability to visualize the data in plan view or cross section would be valuable to maximize the benefits of NUCAPS data in AWIPS. A multi-organizational collaboration through the JPPS Soundings Applications Initiative developed the capability for plan view and cross section displays of NUCAPS in AWIPS (i.e., Gridded NUCAPS).

Berndt, Emily↗
NASA NTRS2020

Forest Potential Productivity Mapping by Linking Remote-Sensing-Derived Metrics to Site Variables

A fine-resolution region-wide map of forest site productivity is an essential need for effective large-scale forestry planning and management. In this study, we incorporated Sentinel-2 satellite data into an increment-based measure of forest productivity (biomass growth index (BGI)) derived from climate, lithology, soils, and topographic metrics to map improved BGI (iBGI) in parts of North American Acadian regions. Initially, several Sentinel-2 variables including nine single spectral bands and 12 spectral vegetation indices (SVIs) were used in combination with forest management variables to predict tree volume/ha and height using Random Forest. The results showed a 10–12 % increase in out of bag (OOB) r2when Sentinel-2 variables were included in the prediction of both volume and height together with BGI. Later, selected Sentinel-2 variables were used for biomass growth prediction in Maine, USA and New Brunswick, Canada using data from 7738 provincial permanent sample plots. The Sentinel-2 red-edge position (S2REP) index was identified as the most important variable over others to have known influence on site productivity. While a slight improvement in the iBGI accuracy occurred compared to the base BGI model (~2%), substantial changes to coefficients of other variables were evident and some site variables became less important when S2REP was included.

site productivity↗
NASA NTRSDate not supplied

Mapping Post-fire Conifer Regeneration using Snow-on Imagery

The 2000 Jasper Fire in the Black Hills of South Dakota was the largest wildfire to date in the region, burning over 83,000 acres of ponderosa pine forest. In collaboration with partners from the United States Forest Service (USFS) Black Hills Experimental Forest, USFS Rocky Mountain Research Station, and United States Geological Survey Geosciences and Environmental Change Science Center, we characterized post-fire forest regeneration within high severity burn patches. We accomplished this by implementing novel conifer detection techniques using a snow index mask to create a winter, snow-on image composite from Landsat 8 Operational Land Imager (OLI) and Sentinel-2 Multispectral Instrument (MSI) data. We utilized 2015 USFS stem maps of field-observed regeneration plots and ocularly sampled reforestation sites planted from 2001–2013. The field data and imagery were used to train a Random Forest (RF) model in Google Earth Engine. The RF model classified conifer regeneration density as low, medium, or high across the high-severity burn area with an overall accuracy of 81.3% for 2021. Approximately 45.9% of the high-severity burn area had low or no regeneration (0-40 trees per acre) 20 years post-fire. Given our partners' desire to find easily accessible low conifer regeneration zones, we identified 4,079 acres of priority planting sites that were within 1,500 feet of roads, had not been planted previously, and were larger than 50 acres. This method supports the use of snow-on imagery as a successful technique to identify conifer regeneration in a post-wildfire landscape.

Yeshey Seldon↗
NASA NTRSDate not supplied

Functionality of the Python Packages for the HERMES Mission

The Heliophysics Environmental and Radiation Measurement Experiment Suite (HERMES) is a set of four instruments that will fly on the Lunar Gateway, an orbital outpost which will support Artemis lunar operations. HERMES will focus on understanding the causes of space-weather variability as driven by the Sun and modulated by the magnetosphere. In this talk, we will discuss the open source approach of the HERMES Science Operation Center (SOC) team being implemented in a number of Python packages which all work together. We will describe the core package which contains Python interfaces for the loading, calibrating, plotting, validating, and saving of measurement data through Common Data Format (CDF) files making use of pycdf provided by spacepy. Each instrument also has a Python package developed using a package template and will provide specific calibration and processing functionality to each instrument. The packages make extensive use of the scientific Python ecosystem and maintain compatibility with PyHC standards. The abstraction of intricate, high heritage data formats, such as CDF files, in Python enables easier analysis and opens doors for greater participation in heliophysics science.

hermes↗
DOE OSTI2020

TRT Compton Scattering Data: Comparisons between LLNL and LANL: Pointwise

This memo is one of a pair of reports comparing Compton scattering data in the context of thermal radiation transport (TRT). This document focuses on Pointwise (PW) data while the other report focuses on Multigroup (MG) data. These complementary analyses, via PW comparisons, show if the same physics are used and if fundamental bugs are present, and, via MG comparisons, quantify macroscopic Compton effects such as mean amplification factors. No averaging of Compton data over photon energy is done for the PW comparisons, while lab-dependent numerical resolution choices become relevant for the MG comparisons. This document plots and quantifies differences in PW Compton scattering data between LANL and LLNL for four disparate temperatures on a logarithmically-spaced energy grid. PW comparisons means we use the received LLNL data as-is, without any averaging or integration over energy. In addition to LANL-to-LLNL comparisons, we investigate the impact of numerical choices on LANL PW data. For the purposes of this comparison, we neglect induced scattering.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Microbial community data from throughfall exclusion experiment: Metadata, SI, community composition, LefSe, and FunGuilR data tables from PARCHED Panama tropical forest soils, 2024-2025

Soil contains more carbon (C) than terrestrial vegetation and the atmosphere combined, with some of the largest terrestrial C stocks in tropical rainforests. Soil microbes decompose organic matter, playing a vital role in the storage or loss of soil C. With climate change, drought conditions are predicted to increase in many tropical regions, including both chronic drying and extended drought, potentially influencing these processes. This project explored the effects of chronic and seasonal drying on soil microbial communities across four distinct tropical forests in a long-term drying experiment. We investigated the effects of a chronic drying manipulation on soil microbial community abundance and variation across different forests and seasons. We also compared findings with previously published data from these forests after short-term drying. This project used soils from a long-term drying experiment established in 2018 across four seasonal lowland forests in Panama. Soils were collected from 0 – 10 cm depths during three seasonal periods in control and drying plots in 2024 and 2025 from a total of 32 plots (n = 4 per forest per treatment). The forests varied in baseline rainfall and soil fertility. We calculated alpha and beta diversity indices and compared taxonomic community composition. We found significant biogeographic variation in microbial diversity and taxonomy, with significant differences across the forests and significant effects of the drying treatment. Metadata and sample IDs are within Metadata_16S.csv and Metadata_ITS.csv. Relative abundance tables of every sample at every season are shown in the Excel workbooks 16S Relative Abundance.xlsx and ITS Relative Abundance.xlsx. They are then also shown in CSV files by each taxonomic level. Linear discriminant analysis effect size (LefSe) tables are shown for the full 16S and ITS datasets (n = 96), subsets for every site at every season (n = 8), and then for the forests with each plot merged by season (n = 8). FunGuildR data table of ITS data is uploaded.

Bacteria↗
NASA NTRS2005

Java-based Graphical User Interface for MAVERIC-II

A computer program entitled "Marshall Aerospace Vehicle Representation in C II, (MAVERIC-II)" is a vehicle flight simulation program written primarily in the C programming language. It is written by James W. McCarter at NASA/Marshall Space Flight Center. The goal of the MAVERIC-II development effort is to provide a simulation tool that facilitates the rapid development of high-fidelity flight simulations for launch, orbital, and reentry vehicles of any user-defined configuration for all phases of flight. MAVERIC-II has been found invaluable in performing flight simulations for various Space Transportation Systems. The flexibility provided by MAVERIC-II has allowed several different launch vehicles, including the Saturn V, a Space Launch Initiative Two-Stage-to-Orbit concept and a Shuttle-derived launch vehicle, to be simulated during ascent and portions of on-orbit flight in an extremely efficient manner. It was found that MAVERIC-II provided the high fidelity vehicle and flight environment models as well as the program modularity to allow efficient integration, modification and testing of advanced guidance and control algorithms. In addition to serving as an analysis tool for techno logy development, many researchers have found MAVERIC-II to be an efficient, powerful analysis tool that evaluates guidance, navigation, and control designs, vehicle robustness, and requirements. MAVERIC-II is currently designed to execute in a UNIX environment. The input to the program is composed of three segments: 1) the vehicle models such as propulsion, aerodynamics, and guidance, navigation, and control 2) the environment models such as atmosphere and gravity, and 3) a simulation framework which is responsible for executing the vehicle and environment models and propagating the vehicle s states forward in time and handling user input/output. MAVERIC users prepare data files for the above models and run the simulation program. They can see the output on screen and/or store in files and examine the output data later. Users can also view the output stored in output files by calling a plotting program such as gnuplot. A typical scenario of the use of MAVERIC consists of three-steps; editing existing input data files, running MAVERIC, and plotting output results.

Seo, Suk Jai↗
NASA NTRS1981

Crop identification and leaf area index calculations with Landsat multitemporal data

Formulas are given to convert land-based vegetative canopy spectral reflectance measurements into Landsat digital counts in the four channels for a clear standard atmosphere. These formulas are shown to predict the curves found by plotting multitemporal Landsat trajectories. With correct interpretation, plots of channel 3 versus channel 4 Landsat data for crops are shown to yield information on both crop identification and crop leaf area index.

Chance, J. E.↗
NASA NTRS1985

Aeroacoustic data for high Reynolds number supersonic axisymmetric jets

Both aerodynamic and near field acoustic behavior of several unheated axisymmetric shock free and shock containing high speed jet plumes are reported. The exit Mach number range for these data is from 0.9 to 2.5. The aerodynamic measurements include both mean and turbulence quantities for a shock free jet plume produced by a convergent divergent nozzle designed to have an exit Mach number of 2. The near field acoustic measurements presented include narrow band spectra, directivity and contour plots of select one third octave band data, and near field microphone correlations from a linear array. Shock noise results are also included as obtained by operating an underexpanded convergent nozzle at the design point of two supersonic exist Mach number convergent divergent nozzles.

Seiner, J. M.↗
DOE OSTI2026

Supervisory Control and Data Acquisition for Electrochemical Separation Experimentation

The Python-based program is a laboratory automation tool designed to control and monitor electrochemical systems. The tool was developed for capacitive deionization (CDI) experiments, but it can be used for any system that requires controlled voltage or current segments and multi-parameter monitoring. The program integrates hardware components to run user-defined experimental parameters, providing operational control of a programmable power supply, peristaltic pump, and data acquisition devices. Currently, the program is structured with a workflow that includes an initialization (or pre-run) phase, a main loop, and a post-experiment stabilization (or post-run) phase. The initialization phase prepares and stabilizes the cell, ensuring that the electrodes and solution reach a baseline state before the experiment begins. The main loop consists of multiple voltage segments that repeat, controlling the experiment while recording key parameters such as time, voltage, current, pH, and conductivity. Finally, the post-experiment stabilization phase allows the system to stabilize after the experiment, returning the cell and solution to equilibrium conditions before ending the sequence. The program is designed with four variations, each tailored to different experimental needs. All variations include both the initialization and post-experiment stabilization stages, which run for a set amount of time, voltage, current, and flow rate before and after the main experiment block. The main loop runs for a set number of cycles, as defined by the user input, and each cycle is composed of 2 or 4 segments. The 4 program variations are described as follows: Program 1: The main program includes 2 segments. Each segment is defined to have a set duration, flow rate, voltage, and current. This program measures conductivity, flow rate, voltage, and current. Program 2: The main program expands Program 1 to include 4 segments. Each segment has a specified duration, flow rate, voltage, and current. Like Program 1, it measures conductivity, flow rate, voltage, and current. Program 3: The main program consists of 2 segments, each defined by time, flow rate, voltage, and current. In addition to conductivity, flow rate, voltage, and current, Program 3 collects pH and temperature data through a 4-channel data acquisition device. Program 4: This program independently controls two channels of a multi-channel power supply simultaneously. While conductivity can only be measured for one cell at a time, the dual-channel control makes it possible to operate two cells simultaneously under different voltage/current conditions. The main program includes 2 segments.For each program, all measurements are automatically logged and integrated into a single Excel output file. Data are displayed in numerical format and plotted, both in real time, to track system performance. A key feature of the program is its ability to synchronize all outputs so that every measurement shares a single timestamp, ensuring accurate alignment of voltage, current, pH, conductivity, and pH data.By combining hardware control, real-time monitoring, and unified data collection, this program significantly reduces manual workload and minimizes errors, making it a reliable platform for researchers, engineers, and laboratory technicians conducting CDI experiments, among other electrochemical tests.

Valentino, Lauren [Argonne National Laboratory (AN↗