Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Core Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Assessment of Thin Plastic Scintillation Detectors for Beta-Particle Measurements at the Advanced Test Reactor Critical Facility

The Fission Wire Measurement System is a custom measurement system designed in the 1960s to measure the beta-particle activity of irradiated uranium-aluminum fission wires. This measurement is conducted to determine the fission rate profile of the Advanced Reactor Test Critical facility. The Advanced Test Reactor Critical facility is an open-pool, low-power test reactor used to qualify experiment configurations and verify core models prior to full-power experiment irradiations in the Advanced Test Reactor. Power distribution measurements in ATR-C use uranium-aluminum wires that are distributed throughout the core to validate simulation and modeling results. These measurements require from 340 to 1500 wires to be irradiated and measured within a 12-hour window. The system consists of 4 measurement channels and one reference channel, each with a 2-pi proportional gas flow detector and the measurement channels each have an automated sample changer. The gas flow detectors are of a custom design for this detector system that use methane gas with a large anode wire compared to modern proportional counters. These detectors, which are nearly 60 years old are irreplaceable. The measurements from these gas detectors are affected by the gas flow rate, atmospheric and line pressure, and are very sensitive to the applied high voltage. Recent improvements have been made to the control and data acquisition system, but the detectors have remained the same. The nature of the measurement of the fission product decay activity is such that the energy spectrum of the signal is changing with time. Thin, 250-um thick, plastic scintillators were commercially obtained as a potential replacement for the gas flow detectors. The original calibration of the uranium-aluminum fission wires was conducted in 1965 using a series of irradiations of gold foils and the wires in a well-characterized thermal neutron field. These measurements provided a time-dependent fission rate conversion factor from the gold foil data to calibrate the fission wires based on the response from the 2-pi proportional gas detectors. Transitioning to the new detectors requires qualification and testing. The sensitivity of the scintillators to changes in the energy spectrum of the fission wires and translation of the calibration factor have been completed. These measurements indicated that the sensitivity of the scintillators over time changes at a different rate than the sensitivity of the gas flow detectors. However, the inverse activity of measurements of both detector types is linear with time. Initial results indicate that the scintillator detectors will be a sufficient replacement for the gas detectors with minor adjustments to the fission rate conversion factor. Replacement of the detectors will improve the fission wire measurements and provide a more stable and reliable measurement system.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2025

Earthquake detection in a simulated lunar regolith using distributed acoustic sensing

Current models of inner lunar geology have largely been inferred from the seismic experiments and observations performed during the Apollo missions that comprised a relatively small number of seismic instruments. Refining constraints on fundamental lunar relationships such as crust-mantle and mantle-core boundaries in the future will require seismic arrays spanning larger epicentral distances. A promising technology for installing dense seismic arrays with minimal human effort is distributed acoustic sensing (DAS), an approach that allows a single length of fiber optic cable to act as hundreds or thousands of sensors when coupled with a DAS interrogator. While terrestrial uses of DAS technology for seismic monitoring rely on burying the cable to maximize fidelity of seismic signal transmission to the fiber, digging meters of trench to bury optical fiber on lunar or planetary surfaces is logistically infeasible. To evaluate DAS signal attenuation due to surface deployment of cable in lunar regolith, we completed earthquake detection analyses that evaluated the sensitivity of an optic-fiber DAS system to seismic signals at different burial depths. We deployed a single-mode fiber in a 10-m open-bottom wooden box filled with a lunar regolith simulant (LRS) with fiber buried at different depths within the LRS and recorded signals for four regional and local earthquakes. The results were used to identify and evaluate signal attenuation in surface-deployed fiber compared to buried fiber in the LRS. Burial depth responses to active-source signals were also evaluated similar to previous studies characterizing DAS sensitivity of surface-deployed fiber. Atmospheric noise was minimal as the cable was deployed in an indoor environment; however, where observed, atmospheric and anthropogenic noise was filtered out using the same bandpass filtering used to identify earthquake events. We found that signal attenuation of the surface-deployed fiber compared to buried fiber was relatively high in active-source experiments but was not consistently observed in earthquake signals. That burial depth is not highly correlated to attenuation of the observed earthquake signals indicates that in a noise-limited environment, placing DAS-interrogated fiber directly at the regolith surface may be a promising deployment strategy to consider for sensing remote seismic signals during lunar exploration.

58 GEOSCIENCES↗
DOE OSTI2026

Soil microbiome resilience to short-term (30 days, 90 days) and long-term (1000 days) drought

This dataset contains data used for the paper "Drought duration does not impact soil microbiome resilience". The Related References will be updated with a full citation when available. Increasing global droughts exert large but poorly understood effects on the microbial communities and ecology of soil. Microbial communities generally show resilience and return to pre-drought conditions when short-term droughted soils are rewet; soils exposed to long-term drought, however, often show a lag upon rewetting, after which microbial communities may or may not return to their pre-stressed conditions. Though short-term droughts have been widely studied, long-term drought manipulation experiments remain rare, especially those that compare microbial response to short-term and long-term drought in tandem. We conducted a 1000-day drought simulation in controlled laboratory conditions with soil cores collected from a tidal freshwater ecosystem in Washington state, USA, and subsequently exposed them to rewetting for two weeks. We also included short-term (30-day and 90-day) drought and rewet treatments to directly compare microbial community and organic matter responses across drought durations. We found distinct microbial taxa belonging to Firmicutes and Actinobacteria enriched after the 1000-day drought, but not after the short-term droughts. While we hypothesized that the microbial community would recover from a short-term drought after rewetting to resemble pre-drought conditions, our results revealed community dissimilarities between rewet and pre-drought conditions across all drought durations. These findings suggest unique microbial life history strategies within certain microbial phyla that make them successful colonizers during an extended drought period, and the influence of environmental and physiological context on microbial responses to rewetting. The 16SrRNA gene amplicon dataset contains processed DNA sequences in the form of an ASV table with raw unrarefied read counts and representative sequences in .fasta format as described in the ESS-DIVE amplicon sequence reporting format (https://ess-dive.gitbook.io/amplicon-sequencing-reporting-format/instructions). The Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (FTICR-MS) dataset consists of processed files containing presence absence data of molecular formulae and molecular characterization of FTICR resolved peaks. The Nuclear Magnetic Resonance (NMR) dataset contains files relevant to NMR spectra and peaks. A sample key file and a sample metadata file is included for the FTICR/NMR and 16S dataset respectively.

1000-day drought↗
DOE OSTI2021

Fabrication and Preliminary Demonstration of Microwave Resonant Cavity Transducer Performance

We are investigating a microwave cavity-based transducer for in-core high-temperature fluid flow sensing in molten salt cooled reactors (MSCR) and sodium fast reactors (SFR). This sensor is a hollow metallic cylindrical cavity, which can be fabricated from stainless steel, and as such is expected to be resilient to radiation, high temperature and corrosive environment of MSCR and SFR. The principle of sensing consists of making one wall of the cylindrical cavity flexible enough so that dynamic pressure, which is proportional to fluid velocity, will cause membrane deflection. Membrane deflection causes cavity volume change, which leads to a shift in the resonant frequency. We have developed an initial design for proof-of-principle testing of the flow sensor performance in microwave K-band. A cylindrical resonator prototype was fabricated from brass for initial tests in water. The cavity size is matched to the flange of a standard WR-42 waveguide. Microwave field is coupled into the resonant cavity through a subwavelength-size aperture. A test article was developed, consisting of a piping Tee with bulkhead WR-42 microwave waveguide installed in leak-proof design. In the test article, the cylindrical cavity is positioned in the center of the pipe. A microwave waveguide circulator was installed in the setup to suppress microwave reflections at the cavity entrance. Preliminary spectral characterization of cavity spectral response was performed with microwave VNA. Applying mechanical pressure to cavity membrane showed a measurable shift in the microwave resonant frequency. We also investigate mechanical integrity of the flowmeter’s membrane through computer simulations. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Synthesis, Redox, and Spectroscopic Properties of Pd(II) 10,10-Dimethylisocorrole Complexes Prepared via Bromination of Dimethylbiladiene Oligotetrapyrroles

Two brominated 10,10-dimethylisocorrole (10-DMIC) derivatives containing Pd(II) centers have been prepared and characterized. These compounds were prepared via bromination of 10,10-dimethylbiladiene-based oligotetrapyrroles. Bromination of free base 10,10-dimethylbiladiene (DMBil1) followed by metalation with Pd(OAc) 2 , as well as bromination of the corresponding Pd(II) dimethylbiladiene complex (Pd[DMBil1]) provide routes to Pd(II) hexabromo-10,10-dimethyl-5,15-bis(pentafluorophenyl)-isocorrole (Pd[10-DMIC-Br 6 ]) and Pd(II) octabromo-10,10-dimethyl-5,15-bis(pentafluorophenyl)-isocorrole (Pd[10-DMIC-Br 8 ]). The solid-state structures of the two brominated isocorrole complexes are presented, as is that for a new decabrominated dimethylbiladiene derivative (DMBil-Br 10 ). The electronic and spectroscopic properties of the brominated biladiene and isocorrole derivatives were probed using a combination of voltammetric methods and steady-state UV–vis absorption and emission experiments. Data obtained from these experiments allow the properties of the brominated biladiene and isocorrole derivatives to be compared to previously studied biladiene derivatives (i.e., DMBil1 and Pd[DMBil1]). CV and DPV experiments demonstrate that Pd[10-DMIC-Br 6 ] and Pd[10-DMIC-Br 8 ] support well-behaved multielectron redox chemistry, similar to that which has been observed for other nonaromatic tetrapyrroles containing sp 3 -hybridized meso-carbons. Here, spectroscopic experiments reveal that bromination of the dimethylbiladiene core shifts this system’s UV–vis absorption profile to lower energy and that the dimethylisocorrole complexes support panchromatic absorption profiles that extend across the UV–vis and into the near-IR region. Photosensitization experiments demonstrate that unlike previously studied Pd(II) biladiene constructs, DMBil-Br 10 , Pd[10-DMIC-Br 6 ], and Pd[10-DMIC-Br 8 ] support limited triplet excited state chemistry with O 2 , indicating that the novel nonaromatic tetrapyrrole derivatives described in this work may be best suited for applications other than singlet oxygen sensitization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Augmented Monitoring and Condition Assessment Program for SNF Wet Storage Life Extension - 20489

Approximately 27 MTHM of spent nuclear fuel (SNF) owned and managed by the U.S. Department of Energy, Office of Environmental Management is stored in the L Basin at the Savannah River Site (SRS). This 'DOE SNF' is comprised of approximately 12,000 aluminum-clad, aluminum-based fuel assemblies (∼7 MTHM), and approximately 2000 non-aluminum fuel assemblies (∼20 MTHM). A program is in progress to perform Non-Destructive Examination (NDE) of the fuel and their storage containers to characterize the materials' condition, and to evaluate the effects of service to enable continued safe wet storage of the SNF. The Augmented Monitoring and Condition Assessment Program (AMCAP), a two-part program to develop and implement remote underwater Non-Destructive Examination of the aluminum SNF, and of the containers of the non-aluminum SNF, respectively, is aimed at the characterization and evaluation of corrosion degradation of aluminum fuel and container materials. The predominant design of the aluminum SNF (ASNF) stored in L Basin is the Materials Test Reactor (MTR) equivalent design, a plate fuel design. These SNF are stored in 5'' diameter tubes or 5'' x 5'' squares (called bundles) that are nominally 12' or up to 14' long. The SNF is de-bundled and inspected using a custom-designed MTR Fuel Inspection Table. The inspection table provides for indexed fuel positioning for a video camera examination with controlled lighting. A total of 10 of the SNF originating from foreign research and test reactors were selected for examination based on burnup, enrichment, and prior damage caused by service/storage history. A special inspection campaign of these 10 assemblies is in progress. The observed corrosion damage included minor to moderate attack from general corrosion, pitting, crevice, end grain and galvanic corrosion. Example results from the completed inspections are shown and discussed. The focus is a comparison of the as-received condition versus the as-found current storage condition that will serve to validate Water Chemistry and Corrosion Monitoring Programs. The non-aluminum SNF (NASNF) stored in L Basin are of diverse design that includes various geometries with claddings of stainless steel, Zircaloy, and Hastelloy. The fuel core materials include uranium alloys, oxides/mixed oxides, and carbides. These SNF materials, originating from early experimental and test reactors, are in various physical forms including single fuel elements and cut pieces. The fuel is stored in L Basin in various configurations including in direct bundled storage in aluminum tubes and in isolation cans that are in the bundles or in a larger over-size storage container (OSC). Concern with inside-out corrosion and the potential loss of configuration control and ability to handle the storage containers prompted the development of remote NDE methods that include visual and UT technologies to assess the condition of the containers. Candidate stored materials were selected for a special inspection campaign; the development of the NDE methods for the inspection for galvanic, crevice and sediment-induced corrosion (inside-out) are discussed. A summary of the SNF storage in L Basin at the SRS, and an overview of the AMCAP to enable continued safe storage of DOE SNF are described. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Stakeholder-Engaged Structured Decision Making for the Los Alamos Legacy Cleanup Mission - 20501

The Los Alamos National Laboratory (LANL) environmental legacy cleanup program requires decisions to be made for environmental remediation, decommissioning and disposal or management of radioactive waste. This legacy cleanup program was established to address groundwater contamination, material disposal areas (MDAs) that have been used to dispose of radioactive and other waste material, and 'aggregate areas' that might produce radioactive or other chemical waste as a result of remediation activities. The LANL site is regulated for environmental concerns under the Resource Conservation and Recovery Act (RCRA). However, some parts of LANL, such as material disposal area G (MDA G), have disposed of radioactive waste under DOE Order 435.1, and are subject to other regulations. For example, decommissioning the remote-handled TRU material stored in 33 shafts at MDA G falls under EPA's 40 CFR 191. Collectively, the regulations are all aimed in the same direction of finding the best solution, either through constructs such as 'as low as reasonably achievable' (ALARA), considering balancing factors as opposed to only cost and human health risk, and, under EPA regulations such as RCRA and NEPA, evaluating impact from all chemicals and both human health and ecological endpoints. Despite the basic goals and objectives of the regulations or their guidance, the main challenge is in their implementation. Arguably perhaps, but really in principle, all of these (and similar) regulations are asking for a decision analysis to be performed. Implementation challenges encountered have included lack of understanding of decision analysis in the industry, lack of effective stakeholder engagement in the decision analysis process, and lack of appreciation of the need to separate value judgments from science, the latter leading to developing conservative, or protective, science-based models. Conservative models lead to poor solutions, lack of effective stakeholder engagement leads to long drawn out protracted approaches to finding a solution (which also might never be found with this approach), and lack of understanding of decision analysis and Bayesian statistics causes poor models to be built, which creates unfortunate situations of 'garbage in, garbage out' becoming the basis for decision making. Stakeholder-engaged structured decision making (SDM) is an approach to solving problems that relies on the theory of decision science to involve stakeholders in the decision-making process. This approach incorporates stakeholder values using a scientifically rigorous methodology that separates value judgments from science in a way that helps avoid the pitfalls of biased, protective, or conservative modeling. This approach has its foundation in Keeney's 1992 treatise on value-focused thinking [1]. Keeney advocated a paradigm shift in decision making based on the idea that the standard way of thinking about decisions is backwards. The standard approach of focusing first on identifying alternatives rather than on articulating values results in a reactive approach with the emphasis on mechanics and fixed choices instead of the core values that have meaning to stakeholders. This paradigm shift effectively engages all stakeholders in the decision-making process while using a values focused thinking approach that can lead to the identification of decision opportunities and the creation of better alternatives. The intent is to be proactive and generate solutions that are related directly to values and objectives as identified by stakeholders. There are, perhaps, two overarching reasons why SDM can be used to benefit LANL's environmental legacy cleanup. Some of LANL's remaining waste management and environmental management problems are challenging and complex (for example, the Cr and RDX plumes, and MDAs) and while the traditional approach has, arguably, worked well for relatively simple risk-based problems, it cannot, or should not, be applied to more complex problems if the most effective and efficient solutions are desired. The second reason is cost. This has perhaps become more critical since publication of the Government Accountability Office (GAO) reports that DoE's environmental liability is considered a high-risk concern for the nation [2]. The focus of SDM is on structuring solutions to decision risk problems by first addressing stakeholder and decision maker values and subsequently developing decision objectives and ways to measure those objectives, preference weighting across objectives, identifying decision alternatives that best achieve those values, and characterizing uncertainty in predictions of the measures. Because a complete decision model is created using SDM, it can be evaluated to find the main elements of the model that drive, or predict, the best solution. This approach creates complete decision models that are transparent, traceable, reproducible and technically defensible. The science behind SDM, or decision analysis, is well founded, yet it is not unusual to see ad hoc approaches to decision making implemented under various environmental regulations that are pertinent to the LANL site, including NEPA, RCRA and DOE Order 435.1. Such ad hoc approaches are often not transparent or traceable, and lack reproducibility and technical defensibility. The LANL legacy cleanup program has embarked on using SDM to address the complex problems that remain. Stakeholder meetings have been held, and a prototype version of the stakeholder value system has been developed. Further meetings are expected in the future to address specific project needs. This is a long-term endeavor considering the complex environmental problems faced by DOE EM in Los Alamos (EM-LA), and careful planning, consideration of stakeholder value systems, and engagement with stakeholders throughout the SDM process is expected to lead to a successful endpoint. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Probing the Sustainable Reduction of CO 2 , N 2 and NO 3 to Fuels and Chemicals using Non-Traditional Porphyrinoid Catalysts

For the last several decades, numerous strategies have been proposed to be able to interconvert electricity and commodity fuels for transportation and other applications. Even as solar and wind energy become more widely available, these renewable energy sources are not always available where the population is most dense or during peak times of energy demand. One plausible solution to the issue of electricity storage and transport is to use electricity to drive the formation of high-energy compounds and chemical fuels. As a result, the electrochemical conversion of CO 2 into chemical fuels has received major attention as a multi-pronged approach for electricity coversion, storage, and transport. Similar strategies are also attractive for conversion of N 2 and NO x into value added compounds such as ammonia. Metalloporphyrin and metallocorrole complexes are comprised of aromatic tetrapyrrole scaffolds and have been extensively studied as homogeneous catalysts for critical catalytic processes like the electrochemical CO 2 reduction reaction (eCO 2 RR) to generate CO as feedstock for the Fischer–Tropsch process to generate a variety of hydrocarbons as chemical fuels. Despite their significance and impact, efficiently driving such catalytic reduction processes is challenging for multiple reasons. Such processes require multiple-electron transfer events, as opposed to single-electron redox chemistry that forms high-energy singly-reduced intermediates. In addition, these electron transfer events must be coupled to proton-transfer steps and avoid application of high overpotentials where proton (H + ) reduction to generate H 2 (as well as other side-reactions) can lower the selectivity and energy efficiency of the eCO 2 RR process. Certain Fe(III) aromatic tetrapyrroles (e.g., porphyrins and corroles) have been reported to overcome these challenges, but are often difficult to synthesize and modify, and have a tendency to support single-electron redox chemistry at the metal as opposed to multielectron redox involving the ligand and metal in concert. Other families of tetrapyrroles in which all four meso-carbons are reduced (i.e., sp 3 -hybridized) are also known in the literature. These non-aromatic tetrapyrroles are known as porphyrinogens and support multi-electron redox chemistry which has been elaborated by several groups, prompting researchers to consider whether these scaffolds may improve the kinetics and efficiencies of multi-electron steps attendant to activation of thermodynamically stable small-molecule substrates such as CO 2 , N 2 , NO 3 − , and NO 2 − . Although porphyrinogens support multi-electron redox properties, the four sp 3 -hybridized meso-carbons inherent to the tetrapyrrole core completely disrupt π-conjugation between pyrrolic units, which compromises the photochemical properties of porphyrinogens in comparison to that of traditional porphyrinoids. Moreover, the highly reducing nature of porphyrinogens predisposes these platforms to extreme air and water sensitivity. Accordingly, such metalated porphyrinogens are often pyrophoric and/or incompatible with many common organic solvents (CH 2 Cl 2 , CHCl 3 , CH 3 CN, EtOAc, etc.). Hence, reports of efficient small-molecule activation or catalysis supported by porphyrinogens have been limited. To overcome the instability of porphyrinogens while retaining the scaffold’s attractive multi-electron redox properties, we have directed attention to establishing less-well studied groups of non-aromatic tetrapyrroles (i.e., phlorins, biladienes, and isocorroles). These non-traditional tetrapyrroles each contain just a single sp 3 -hybridized meso-carbon, which ablates the platforms aromaticity but still provides an extended π-framework. In addition to developing innovative platforms that may be used to sustainably generate value-added chemicals, fuels, and ammonia via either photo- or electrocatalytic approaches our work also has significantly broadened our understanding of how to prepare and modulate the properties of non-aromatic tetrapyrroles for other applications. Our efforts entailed a synergistic partnership and active collaborations with Drs. David C. Grills and Mehmed Z. Ertem (both of Brookhaven National Lab) to better characterize isocorroles (and related non-aromatic tetrapyrroles) using a variety of advanced spectroscopic and theoretical methods. Our combined efforts have shown that the combination of properties that isocorroles (and related tetrapyrroles) provide results in good chemical stability paired with unique redox and photochemical characteristics that are not typically supported by simple and/or unadorned aromatic tetrapyrroles. Beside redox chemistry, the photochemistry of isocorroles and other non-aromatic tetrapyrroles containing one sp 3 -hybridized meso-carbon is also appealing due to their absorption in the long-visible to near-IR regions, which are essential for photocatalysis and related applications that benefit from direct excitation at these wavelengths. The results reported vastly improve our understanding of non-aromatic tetrapyrrole synthesis, properties and utility for activation of small molecule substrates such as O 2 and CO 2 in the presence of weak cationic organic acids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Multicode benchmark on simulated Ti K-edge x-ray absorption spectra of Ti-O compounds

X-ray absorption spectroscopy (XAS) is an element-specific materials characterization technique that is sensitive to structural and electronic properties. First-principles simulated XAS has been widely used as a powerful tool to interpret experimental spectra and draw physical insights. Recently, there has also been growing interest in building computational XAS databases to enable data analytics and machine learning applications. However, there are non-trivial differences among commonly used XAS simulation codes, both in underlying theoretical formalism and in technical implementation. Reliable and reproducible computational XAS databases require systematic benchmark studies. In this work, we benchmarked Ti K-edge XAS simulations of ten representative Ti-O binary compounds, which we refer to as the Ti-O-10 dataset, using three state-of-the-art codes: XSPECTRA, OCEAN and exciting. We systematically studied the convergence behavior with respect to the input parameters and developed a workflow to automate and standardize the calculations to ensure converged spectra. Our benchmark comparison considers a 35 eV spectral range starting from the K-edge onset, representative of widely used near-edge spectra. Quantitative comparison over this range is based on Spearman’s rank correlation score (r sp ). Our results show: (1) the two Bethe-Salpeter equation (BSE) codes (OCEAN and exciting) have excellent agreement with an average $r$ $sp$ of 0.998; (2) good agreement is obtained between the core-hole potential code (XSPECTRA) and BSE codes (OCEAN and exciting) with an average $r$ $sp$ of 0.990, and this smaller $r$ $sp$ reflects the noticeable differences in the main edge spectral shape that can be primarily attributed to the difference in the strength of the screened core-hole potential; (3) simulations from both methods overall reproduce well the main experimental spectral features of rutile and anatase, and the different treatments of the screened core-hole potential have visible impact on pre-edge intensities and the peak ratio of the main edge; (4) there exist moderate differences in the relative edge alignment of the three codes with a standard deviation of about 0.2 eV, which arise from multiple contributions including the frozen core approximation, final state effects, and different approximations used for the self-energy correction. In conclusion, our benchmark study provides important standards for first-principles XAS simulations with broad impact in data-driven XAS analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impacts of advanced diesel combustion operation and fuel formulation on soot nanostructure and reactivity

Advanced diesel combustion, accomplished via a single pulse fuel injection and high levels of exhaust gas recirculation (referred to as “PCCI”, partially-premixed charge compression ignition), is shown to be a path to reduce oxides of nitrogen and particulate matter simultaneously. This is well established in the literature. Less established is the extent to which such dilute combustion processes influence soot formation and affect soot that is emitted from diesel engines under such combustion modes. This work focuses on characterization of the nanostructure and oxidative reactivity of soot generated by a light-duty turbodiesel engine operating under a PCCI combustion mode, a dilute, low-temperature combustion process. Previous work on a type of PCCI combustion, referred to as high-efficiency clean combustion (HECC), showed soot samples having a fullerenic nanostructure, characterized by high levels of tortuosity of the fringe layers as seen in transmission electron micrograph images and as quantified using an image processing algorithm. Thermogravimetric analysis of the HECC mode soot samples showed that they displayed higher rates of oxidation than soot samples from a conventional diesel combustion mode. The present work returns to PCCI combustion, considering the timing of the main fuel injection, and the effects of operating on fuels rich in n-alkanes, particularly a fuel produced from a low temperature Fischer-Tropsch process (LTFT) and a renewable diesel fuel (RD) produced via hydrodeoxygenation of a plant oil. PCCI combustion conditions yield soot that shows higher reactivity compared to soot from the conventional combustion mode regardless of fuel type. LTFT and RD fuels produce soots with lower reactivity compared to ULSD. Soots produced from PCCI combustion have higher surface oxygen concentration and higher proportion of amorphous carbon. In addition, TEM images show that PCCI soots from all three fuels have smaller primary particle and particle aggregate sizes, and smaller graphene layers. These properties explain the higher reactivity of soot from PCCI combustion. The less reactive soots, which are produced from LTFT and RD fuel under conventional combustion, show internal burning during oxidation. However, soots with higher reactivity which are produced from late injection PCCI combustion and ULSD show shrinking core oxidation, most likely because of their overall amorphous structure.

42 ENGINEERING↗
DOE OSTI2024

Report Summarizing the Mechanical Properties of a Large ODS Ferritic Alloy Ingot by Forging at High Temperatures for Future Mother Tube Production

Oxide dispersion strengthened (ODS) ferritic alloys are considered the benchmark fuel cladding and core structural material in advanced nuclear energy reactors that require high-temperature strength and creep properties and resistance to radiation damage. The ODS ferritic alloys including 14YWT are produced by mechanical alloying (MA), which is time-consuming and is associated with high manufacturing costs that are not beneficial to being used in advanced nuclear energy reactors. This report summarizes the accomplishments in FY24 in the INM program for producing an ODS ferritic alloy by high-deformation, high-temperature processing of reactive and ferritic alloy powders for advanced reactor fuel cladding applications. Following four hot forging experiments, it was concluded that several significant challenges were encountered that were difficult to overcome. These challenges were related to using high annealing temperatures for pressure assisted sintering processes to produce dense microstructures, but the high annealing temperatures result in long range diffusion of Ti through the bcc Fe lattice and react with the YIG particles that are distributed on the prior surfaces of the ferritic alloy powders. In addition, it was determined that the high deformations induced by forging at high temperatures were not very effective for fracturing the reactive YIG particles into smaller particles and distributing them into the interior of the ferritic alloy powders. Spark plasma sintering was attempted for shortening the time at high temperatures, which led to full densification but the microstructure characterization results still showed that Ti atoms diffused over long distances in the bcc Fe lattice and reacted with the YIG particles. Finally, a short 30 minute high intensity ball milling experiment was conducted on blended 14WT and YIG powders for inducing severe deformations that caused the initially spherical powders of 14WT decorated with the YIG particles on the surfaces to transform to flakes and fracturing of YIG particles into smaller particles that were incorporated into the bcc Fe lattice. Two forgings were performed with the high intensity milled powders: first annealing for 20 minutes at 850ºC followed by forging and second annealing for 20 minutes at 1,100ºC followed by forging. At 850ºC, Ti atoms are effectively immobile, thus allowing for densification albeit incomplete. The deformation by forging after annealing for 20 minutes at 1,100ºC favored dynamic recrystallization processes that led to nano-size grains with very high stored energy due to high dislocation density. The corresponding VH data showed significant hardening that correlated with estimated strengthening of ~1650 MPa. This hybrid processing approach combining high intensity ball milling of powder with annealing and forging showed the most promise for producing an oxide dispersing strengthened ferritic alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Main and Satellite Features in the Ni 2p XPS of NiO

The origin and assignment of the complex main and satellite XPS features of the cations in ionic compounds has been the subject of extensive theoretical studies using different methods. There is agreement that within a molecular orbital model one needs to take into account different types of configurations. Specifically, those where a core electron is removed but no other configuration changes are made and those where in addition to ionization there are also shake or charge transfer changes to the ionic configuration. However, there are strong disagreements about the assignment of XPS features to these configurations. The present work is directed toward resolving the origin of main and satellite features for the Ni 2p XPS of NiO based on ab initio molecular orbital wavefunctions for a cluster model of NiO. A major problem in earlier ab initio XPS studies of ionic compounds has been the use of a common set of orbitals that was not able to properly describe all the ionic configurations that contribute to the full XPS spectra. This is resolved in the present work by using orbitals that are optimized for averages of the occupations of the different configurations that contribute to the XPS. The approach of using State Averaged orbitals is validated through comparisons between different averages and through use of higher order excitations in the wavefunctions for the ionic states. It represents a major extension of our earlier work on the main and satellite features of the Fe 2p XPS of Fe 2 O 3 and proves the reliability and the generality of the assignments of the character and origin of the different features of the XPS obtained with orbitals optimized for State Averages. These molecular orbital methods permit the characterization of the ionic states in terms of the importance of shake excitations and of the coupling of ionization of 2p 1/2 and 2p 3/2 spin-orbit split sub shells. Further, the work lays the foundation for definitive assignments of the character of main and satellite XPS features and points to their origin in the electronic structure of the material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Physical Parameters of the Multiplanet Systems HD 106315 and GJ 9827

HD 106315 and GJ 9827 are two bright, nearby stars that host multiple super-Earths and sub-Neptunes discovered by K2 that are well suited for atmospheric characterization. We refined the planets’ ephemerides through Spitzer transits, enabling accurate transit prediction required for future atmospheric characterization through transmission spectroscopy. Through a multiyear high-cadence observing campaign with Keck/High Resolution Echelle Spectrometer and Magellan/Planet Finder Spectrograph, we improved the planets’ mass measurements in anticipation of Hubble Space Telescope transmission spectroscopy. For GJ 9827, we modeled activity-induced radial velocity signals with a Gaussian process informed by the Calcium II H&K lines in order to more accurately model the effect of stellar noise on our data. We measured planet masses of M {sub b} = 4.87 ± 0.37 M {sub ⊕}, M {sub c} = 1.92 ± 0.49 M {sub ⊕}, and M {sub d} = 3.42 ± 0.62 M {sub ⊕}. For HD 106315, we found that such activity radial velocity decorrelation was not effective due to the reduced presence of spots and speculate that this may extend to other hot stars as well (T {sub eff} > 6200 K). We measured planet masses of M {sub b} = 10.5 ± 3.1 M {sub ⊕} and M {sub c} = 12.0 ± 3.8 M {sub ⊕}. We investigated all of the planets’ compositions through comparison of their masses and radii to a range of interior models. GJ 9827 b and GJ 9827 c are both consistent with a 50/50 rock-iron composition, GJ 9827 d and HD 106315 b both require additional volatiles and are consistent with moderate amounts of water or hydrogen/helium, and HD 106315 c is consistent with a ∼10% hydrogen/helium envelope surrounding an Earth-like rock and iron core.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Regimes of evaporation and mixing behaviors of nanodroplets at transcritical conditions

The objective of this paper is to examine the fundamental mechanisms responsible for the transition between subcritical evaporation and supercritical dense-fluid-mixing in the absence of convection effects, specifically focusing on the liquid–vapor interfacial dynamics. To isolate the dynamics of this transition process, we characterize the different physical behaviors exhibited by an -dodecane nanoscale droplet placed in different nitrogen ambient conditions across the fuel’s critical point. We employ a continuum-based interface-resolving diffuse-interface method to explore the underlying phase-exchange mechanisms that bring about such distinct dynamics. Following the comparison against molecular dynamics simulations and experiments of evaporating droplets and experimental data for vapor–liquid equilibria, a parametric study at various ambient conditions and droplet sizing is performed to identify four regimes of evaporation/mixing behaviors: sub- and supercritical droplet evaporation, and sub- and supercritical dense-fluid-mixing. It is shown that the distinction in the phase-exchange mechanisms in these four regimes are brought about by the different thermodynamic phases the droplet center can exhibit during the evaporation/mixing process: subcritical liquid, supercritical liquid-like, subcritical gaseous, and supercritical gas-like, respectively. It is shown that the subcritical dense-fluid-mixing behavior is a direct result of nanoconfinement of the liquid–vapor interfacial structure and thus is not present for large droplet sizes. Finally, the present study also shows that the supercritical phase-exchange dynamics can follow two different pathways: supercritical droplet-like evaporation and supercritical dense-fluid-mixing. Furthermore, promoting the early transition to supercritical dense-fluid-mixing can significantly expedite the phase-exchange process through the disintegration of the liquid-like droplet core.

42 ENGINEERING↗
DOE OSTI2020

Characterization of Oxy-Coal Swirl Injector

The article presents the design and testing of a coal-slurry swirl-pintle injector for high pressure oxy-coal combustion systems. Pressurized oxy-coal combustion-based systems have the potential to improve efficiency by recovering latent heat of the steam in flue gas and achieve 90% CO2 capture. In oxy-coal combustion, coal is burned in the presence of pure oxygen, which results in higher efficiency and less greenhouse gas in the exhaust. With the advancement of pressurized oxy-coal combustor research, there is a need to investigate injector technology suitable for this unique combustion approach. Effective atomization and mixing of coal-slurry and oxidizer pose a challenge for the efficient burning of coal particles. A swirl-pintle type injector was designed and tested to enhance the atomization of the coal-water slurry spray by adding a swirl to the oxygen flow path. Although pintle type injectors are traditionally used in rocket engines, they present a promising approach in clean coal combustion technology due to higher mixing effectiveness and enhanced performance. The mixing behavior of three pintle injectors with different swirl numbers (S = 0, 0.9, and 1.2) was tested using a high-speed shadow sizing technique. Mixture ratios of 30% (by mass) coal-water slurry were studied. The droplet diameter and dispersion characteristics were determined from shadow images of coal-water spray. The jet breakup length, droplet number, total moment ratio (TMR), and Ohnesorge number were then calculated to compare the performance of different injectors. The paper presents an empirical correlation of the TMR with droplet size and spray regimes. For a pintle injector with S = 1.2 swirler, the droplets diameter was found to be in the range of 1 mm to 12 mm. The jet breakup length was also shorter in comparison to S= 0 and 0.9 injectors. A second atomization zone was also observed at 2 and 5 diameters downstream of injector exist at spray edge and jet core respectively

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Selective penetration behavior of microgels in superpermeable channels and reservoir matrices

Gel treatment is an effective way to attack excessive water production in many mature oilfields around the world. Selective penetration is desired for successful gel treatments. That is, gel materials should easily penetrate the target zones (i.e., channeling features such as superpermeable channels) without entering/damaging the nontarget zones (i.e., reservoir matrices or oil zones). This study revealed that presence of threshold penetration pressure (ΔP th ) was responsible for selective penetration behavior of tested microgels. The concept of ΔP th was utilized to figure out favorable working conditions for effective gel treatments. Microgel dispersions were injected into superpermeable (super-k) sandpacks (mimicking super-k channels in reservoirs, 60–221 darcies), heterogeneous models with super-k channels (79–230 darcies), and sandstone cores (mimicking reservoir matrices, 50–5000 md). The results demonstrated that a minimum differential driving pressure (i.e., threshold penetration pressure, ΔP th ) was required to push microgel particles to penetrate channels or matrices. The critical penetration behavior was closely related to the particle/pore size ratio. Low ΔP th at smaller particle/pore ratios was beneficial to allow easy penetration of gel materials into the channeling zones. On the contrary, high ΔPth at larger particle/pore ratios was desirable to prevent gel materials from massively invading and damaging the matrices. Instead, the gel particles accumulated at the inlet surface, and a gel cake was gradually formed. The cake further prevented the invasion of the gels. The cake could be removed by chemical breakers to resume the injectivity/productivity of the matrices. Correlations were developed to describe the relationship between ΔP th and particle/pore ratio. A distinct transition was identified at the particle/pore ratio of about 3. This research could help identify the favorable conditions to achieve successful gel treatments. In an effective conformance treatment, the particle/pore ratio in the channel should be sufficiently low to allow easy penetration of gel materials into the channel (e.g., particle/pore ratio<2 in this study). Meanwhile, the particle/pore ratio in the matrix should be large enough to support a high ΔP th and thus prevent massive gel invasion into the matrix. This study advances the current pore scale studies (a single particle passing through a single channel) to Darcy-scale characterization.

02 PETROLEUM↗
DOE OSTI2021

Experimental and Theoretical Study of the Electronic Structures of Lanthanide Indium Perovskites LnInO 3

Ternary lanthanide indium oxides LnInO 3 (Ln = La, Pr, Nd, Sm) were synthesized by high-temperature solid-state reaction and characterized by Xray powder diffraction. Rietveld refinement of the powder patterns showed the LnInO 3 materials to be orthorhombic perovskites belonging to the space group Pnma, based on almost-regular InO 6 octahedra and highly distorted LnO 12 polyhedra. Experimental structural data were compared with results from density functional theory (DFT) calculations employing a hybrid Hamiltonian. Valence region X-ray photoelectron and K-shell X-ray emission and absorption spectra of the LnInO 3 compounds were simulated with the aid of the DFT calculations. Photoionization of lanthanide 4f orbitals gives rise to a complex final-state multiplet structure in the valence region for the 4f n compounds PrInO 3 , NdInO 3 , and SmInO 3 , and the overall photoemission spectral profiles were shown to be a superposition of final-state 4f n-1 terms onto the cross-section weighted partial densities of states from the other orbitals. The occupied 4f states are stabilized in moving across the series Pr-Nd-Sm. Band gaps were measured using diffuse reflectance spectroscopy. These results demonstrated that the band gap of LaInO 3 is 4.32 eV, in agreement with DFT calculations. This is significantly larger than a band gap of 2.2 eV first proposed in 1967 and based on the idea that In 4d states lie above the top of the O 2p valence band. However, both DFT and X-ray spectroscopy show that In 4d is a shallow core level located well below the bottom of the valence band. Band gaps greater than 4 eV were observed for NdInO 3 and SmInO 3 , but a lower gap of 3.6 eV for PrInO 3 was shown to arise from the occupied Pr 4f states lying above the main O 2p valence band.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Hyaloscypha finlandica Metabolome Repository

This repository provides the curated data tables, manuscript figure and table exports, dependency records, and workflow scripts supporting an integrated comparative genomics and untargeted LC-MS/MS metabolomics analysis of Hyaloscypha finlandica strain PMI 746, a root-associated dark septate endophyte of poplar. The repository includes genome-mining summaries from antiSMASH, FunBGCeX, BGC-Prophet, and BiG-SCAPE; processed metabolomics inputs; metabolite annotation evidence; statistical outputs; and publication-facing figures and tables. Raw LC-MS/MS spectra, full genome/protein downloads, and large generated tool outputs are referenced through public archive/accession records and are not stored in Git.

59 BASIC BIOLOGICAL SCIENCES↗