Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Conditional Normalizing Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Blind Modeling Validation Exercises Using the Horizontal Dry Cask Simulator

The U.S. Department of Energy (DOE) established a need to understand the thermal-hydraulic properties of dry storage systems for commercial spent nuclear fuel (SNF) in response to a shift towards the storage of high-burnup (HBU) fuel (> 45 gigawatt days per metric ton of uranium, or GWd/MTU). This shift raises concerns regarding cladding integrity, which faces increased risk at the higher temperatures within spent fuel assemblies present within HBU fuel compared to low-burnup fuel (≤ 45 GWd/MTU). A dry cask simulator (DCS) was built at Sandia National Laboratories (SNL) in Albuquerque, New Mexico to produce validation-quality data that can be used to test the accuracy of the modeling used to predict cladding temperatures. These temperatures are critical to evaluating cladding integrity throughout the storage cycle of commercial spent nuclear fuel. A model validation exercise was previously carried out for the DCS in a vertical configuration. Lessons learned during the previous validation exercise have been applied to a new, blind study using a horizontal dry cask simulator (HDCS). Three modeling institutions – the Nuclear Regulatory Commission (NRC), Pacific Northwest National Laboratory (PNNL), and Empresa Nacional del Uranio, S.A., S.M.E. (ENUSA) – were granted access to the input parameters from the DCS Handbook, SAND2017-13058R, and results from a limited data set from the horizontal BWR dry cask simulator tests reported in the HDCS update report, SAND2019-11688R. With this information, each institution was tasked to calculate peak cladding temperatures and air mass flow rates for ten HDCS test cases. Axial as well as vertical and horizontal transverse temperature profiles were also calculated. These calculations were done using modeling codes (ANSYS/Fluent, STAR-CCM+, or COBRA-SFS), each with their own unique combination of modeling assumptions and boundary conditions. For this validation study, the ten test cases of the horizontal dry cask simulator were defined by three independent variables – fuel assembly decay heat (0.5 kW, 1 kW, 2.5 W, and 5 kW), internal backfill pressure (100 kPa and 800 kPa), and backfill gas (helium and air). The plots provided in Chapter 3 of this report show the axial, vertical, and horizontal temperature profiles obtained from the dry cask simulator experiments in the horizontal configuration and the corresponding models used to describe the thermal-hydraulic behavior of this system. The tables provided in Chapter 3 illustrate the closeness of fit of the model data to the experiment data through root mean square (RMS) calculations of the error in peak cladding temperatures (PCTs), PCT axial locations, axial temperature profiles, vertical and horizontal temperature profiles at two different axial locations, and air mass flow rates for the ten test cases, normalized by the experimental results. The model results are assigned arbitrary model numbers to retain anonymity. Due to the relatively flat axial temperature profiles, small temperature gradients resulted in large deviations of all models’ PCT axial location from the experimental PCT axial location. When the PCT axial location error is excluded in the calculation of the combined RMS of the normalized errors that considers PCT, the temperature profiles, and the air mass flow rates, the model data fits the experimental data to within 5%. When the vault information is excluded, the model data fits the experimental data to within 2.5%. An error analysis was developed further for one model, using the model and experimental uncertainties in each validation parameter to calculate validation uncertainties. The uncertainties for each parameter were used to define quantifiable validation criteria. For this analysis, the model was considered validated for a given comparison metric if the normalized error in that metric divided by the validation uncertainty was less than or equal to 1. When considering the combined RMS of the normalized errors of all metrics divided by their validation uncertainties, the model was found to have satisfied the criterion for model validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigating the relationship between simulation parameters and flow variables in simulating atmospheric gravity waves for wind energy applications

Wind farms, particularly offshore clusters, are becoming larger than ever before. Besides influencing the surface wind flow and the inflow for downstream wind farms, large wind farms can trigger atmospheric gravity waves in the inversion layer and the free atmosphere aloft. Wind-farm-induced gravity waves can cause adverse pressure gradients upstream of the wind farm, which contribute to the global blockage effect, and can induce favorable pressure gradients above and downstream of the wind farm that enhance wake recovery. Numerical modeling is a powerful means of studying these wind-farm-induced atmospheric gravity waves, but it comes with the challenge of handling spurious reflections of these waves from domain boundaries. Typically, approaches which employ radiation boundary conditions and forcing zones are used to avoid these reflections. However, the simulation setup of these approaches relies heavily on ad hoc processes. For instance, the widely used Rayleigh damping method requires ad hoc tuning to produce a setup that may only produce satisfactory results for a particular case. To provide more systematic guidance on setting up realistic simulations of atmospheric gravity waves, we conduct a large-eddy simulation (LES) study of flow over a 2D hill and through a wind farm canopy that explores the optimum domain size and damping layer setup depending on the fundamental parameters which determine the flow characteristics. In this work, we only consider linearly stratified conditions (i.e., no inversion layer), thereby focusing on internal gravity waves in the free atmosphere and their reflections from the domain boundaries. This type of flow is governed by a single Froude number, which dictates most of the internal wave properties, such as wavelength, amplitude, and direction. This, in turn, will dictate the optimum domain size and Rayleigh damping layer setup. We find the effective horizontal and vertical wavelengths (the representative wavelengths of the entire wave spectrum) to be the appropriate length scales to size the domain and damping layer thickness, and the optimal Rayleigh damping coefficient scales with the Brunt–Väisälä frequency. Considering Froude numbers seen in wind farm applications, we propose recommendations to limit the reflections to less than 10 % of the total upward-propagating wave energy. Typically, damping is done at the top boundary, but given the non-periodic lateral boundary conditions of practical wind farm simulation domains, we find that damping the inflow–outflow boundaries is of equal importance to damping the top boundary. The Brunt–Väisälä frequency-normalized damping coefficient should be between 1 and 10. The damping layer thickness should be at least one effective vertical wavelength; damping layers exceeding 1.5 times the vertical wavelength are found to be unnecessary. The domain length and height should accommodate at least one effective horizontal and vertical wavelength, respectively. Moreover, Rayleigh damping does not damp the waves completely, and the non-damped energy might accumulate over the simulation time.

17 WIND ENERGY↗

Flame Design: A Novel Approach Developed to Produce Clean, Efficient Diffusion Flames

Soot formation and flame extinction are vital concerns in the combustion of fossil fuels. In particular, soot is responsible for pollutant emissions, and extinction can cause inefficient or unstable burning. Normal-gravity experiments have demonstrated that flames can be designed to improve both characteristics by redirecting some or all of the nitrogen from the oxidizer into the fuel. Such nitrogen exchange can produce permanently blue flames, which are soot free under all possible flame conditions. Furthermore, this approach can lead to stronger, extinction-resistant flames. Past investigations of nitrogen exchange were unable to identify the physical mechanisms responsible for its benefits because these mechanisms cannot be isolated when normal-gravity flames are studied. In contrast, the Diffusion Flame Extinction and Soot Inception (DESI) experiment considers spherical flames, where nearly perfect spherical symmetry affords new levels of control. Because of buoyancy, spherical flames cannot be created in Earth s gravity. DESI was conceived by principal investigator Professor R.L. Axelbaum of Washington University in St. Louis. Tests to date have utilized the 2.2-Second Drop Tower at the NASA Glenn Research Center at Lewis Field. The experiment is slated for testing aboard the International Space Station in a few years. Two mechanisms have been proposed to explain the connection between nitrogen exchange and permanently blue flames. These are the structure (chemical effects) and hydrodynamics (flow direction and speed). In normal-gravity flames, the structure and hydrodynamics are coupled, since nitrogen exchange simultaneously modifies both. Spherical microgravity flames, on the other hand, allow independent control of these factors. Specifically, structure can be modified via nitrogen exchange, and flow direction can be reversed by swapping the ambient and burner-feed gases. In DESI, these variations can be accomplished without changing the theoretical flame temperature.

Axelbaum, Richard L.↗

Comparison of equivalence ratio transients on combustion instability in single-nozzle and multi-nozzle combustors

Low-emissions gas turbine combustion, achieved through the use of lean, premixed fueling strategies, is susceptible to combustion instability. The driving mechanism for this instability arises from fluctuations of pressure, fuel/air flow rate, and heat release rate. If these fluctuations are relatively in-phase, the combustion system will evolve to a self-excited state. The self-excited instability frequency and amplitude depend mainly on the operating condition and the geometry of the combustor. In this study, we consider the onset and decay of self-excited instabilities, resulting from transients in fuel/air ratio, in both single-nozzle and multi-nozzle combustors. In particular, we examine the differences in the instability onset and decay processes between these two flame configurations, as most gas turbine combustors have multiple nozzles, but most gas turbine combustor experiments utilize a single-nozzle. A nonlinear logistic regression analysis is applied to study the timescales of the decay and onset transients. Variations in the equivalence ratio change the heat release rate distribution inside the combustor, which is captured using chemiluminescence imaging. The normalized Rayleigh index, which shows the spatial distribution of the instability driving, is calculated to analyze the driving strength in different regions of the flame. Comparisons between the single- and multi-nozzle flame transients, including both center and outer flames for the multi-nozzle combustor, suggest that both confinements from the wall and flame-flame interaction are crucial to determining flame dynamics as the equivalence ratio transient changes the heat release rate distribution near corner recirculation zone and flame shear layers.

20 FOSSIL-FUELED POWER PLANTS↗

Shock-Layer Radiation Insights Available Through Flowfield Property Binning

This paper introduces a method for assessing similarity between available shock-layer radiation measurements and the radiative heating to a vehicle of interest. This method will be referred to as the flowfield property binning (FPB) approach. The challenge in developing this approach is that radiometer measurements from a surface normal line of sight, observed radiation measurements of the entire shock-layer from a distance, or measured shock-tube nonequilibrium profiles are notably different geometrically than the radiative flux to a vehicle surface. Therefore, the relative contributions of various regions of the shock-layer to the measurement, and how these relative contributions compare with the radiative heating to a vehicle of interest, are unclear. By tracking the radiation contribution from each flowfield location, and then grouping this contribution based on two local flowfield properties, these geometric differences are removed. This provide a two dimensional group, or bin, distribution that represents the radiation environment in the same format for various types of radiation simulations, such as observed radiation or radiative flux to a vehicle surface. In the limits of optically-thin radiation transport and thermochemical equilibrium flow, the choice of pressure and temperature as the binning flowfield properties is shown to provide a bin distribution that uniquely defines the radiation simulation. This concept is found to be sufficient for establishing similarity between two cases even when the optically-thin radiation transport and thermochemical equilibrium assumptions are not satisfied. A simple metric of comparison between bin distributions from different cases is provided by the histogram intersection algorithm. This algorithm results in a histogram intersection factor (H) between 0 and 1, which represents the fraction of the radiation that is similar between the two cases. Therefore, if H evaluated between bin distributions for two completely different radiation problems is near 1, then they represent essentially the same radiation problem. This means that they depend on the same weighting of various radiation modeling parameters evaluated at the same pressure and temperature. If one of these cases agrees well with a radiation measurement, then the matching bin distributions provide justification for applying this experimental validation to the other case. Even for H values as low as 0.2, the measurement case could be considered relevant if there are no other useful measurements. This approach allows observed radiation measurements to directly inform radiative heating simulations, which allows NASA’s past and future investments in observed radiation measurements to directly inform the radiative heating uncertainty or margins for future vehicle design. This FPB approach is also used to determine shock-tube conditions for informing backshell radiative heating simulations, where the normal shock velocity and Lagrangian time from the shock is used for the binning variables instead of pressure and temperature.

Shock Layer Radiation↗

Hyporheic Oxygen Dynamics in the East River, Colorado: Insights From an In–Situ, High Frequency Time Series During Two Distinct Flow Seasons

Dissolved oxygen (DO) is critical for aquatic ecosystems, however, few studies have focused on the long-term DO dynamics in hyporheic zones, which are a function of both transport (hydrologic exchange between river and hyporheic zone) and uptake by biogeochemical reactions or respiration. We explore the dynamics of temperature and DO at 10, 20, and 35 cm depth beneath the East River, Colorado, from July–October 2017 (relatively normal water year) and April to October 2018 (comparatively low flow year), enabled by distinctive, in-situ, high frequency (Δt = 5 min) sensors that provided continuous time-series from the undisturbed study site over 14 months. We expect that hyporheic DO, which has a regular daily fluctuation pattern, is supplied by the surface water (at all times we estimate downwelling) and that diurnal hyporheic DO temporal patterns should be aligned with diurnal hyporheic temperature patterns. However, this was not found to be the case. Hyporheic DO becomes depleted briefly at 20 and 35 cm depths in 2017, and at all three hyporheic depths for extended periods in 2018. Whereas diurnal temperature fluctuations have consistent timings of maxima and minima, hyporheic DO rarely has as regular a pattern, and daily ranges are inconsistent. Rainfall events caused some of these changes to diurnal hyporheic DO patterns without repeatable effects. Antecedent snowpack conditions influence streamflow dynamics and therefore hyporheic DO dynamics in this alpine river. These results also point to the strong and variable influence of hyporheic microbial communities regulating hyporheic DO.

54 ENVIRONMENTAL SCIENCES↗

Mechanical response of 99.999% purity aluminum under dynamic uniaxial strain and near melting temperatures

In this study, a series of reverse geometry normal plate impact experiments are employed to investigate the incipient plastic behavior of commercial purity polycrystalline aluminum under ultra-high strain-rates (~105 /s) and test temperatures up to melt (i.e. 643 °C). The applied stress at the aluminum/target interface, as inferred from the measured normal free-surface particle velocity record, shows progressive weakening with increasing test temperatures ranging from 23–620 °C; at higher temperatures (470–620 °C) this rate of weakening is observed to decrease, and at the highest test temperatures employed in the study, i.e. temperatures approaching the melt point of aluminum (643 °C), a net increase in the longitudinal stress is observed. Additionally, estimates of longitudinal elastic impedance of the sample material, as inferred via impedance matching from the particle velocity states at shock plateau show similar monotonic decrease with temperature, except for the highest test temperature case, in which reversal of this trend is observed. Though slight, these noticeable changes in the impedance, and stress/velocity states likely indicate variances in the strengthening/hardening response of the material, which can be linked to transition in the dominant plastic flow mechanisms as the sample approaches the melting point. Scanning electron microscopy of the impact surface of the post-test samples reveal coarsening of the sample grains due to static recrystallization during the heating phase of the experiment. Additional experiments are performed on annealed specimens to probe the effects of microstructural changes, i.e. grain size, and/or relief of residual strains in the interpretation of the measured response of aluminum. Finally, the results, which show a decrease in the longitudinal acoustic impedance, and decrease in the levels of stress/particle velocity under shock loading, indicate that the effects of annealing may play a role in the observed response by promoting softening of the dynamic strength, and/or lessening of the rate of hardening in a post-yield regime.

36 MATERIALS SCIENCE↗

Enhanced Mixing in a Rectangular Duct

An experimental investigation of the mixing of non-reacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. Particular emphasis was placed on the study of closely spaced orifice configurations applicable to the mixing zone of an RQL combustor. Baseline studies were performed of mixing under "ideal" conditions, i.e., plenum fed jets injecting into a crossflow uniform in velocity and turbulence intensity. In addition, more practical ("non-ideal") issues encountered during hardware design were also studied. As in other studies, mixing effectiveness, determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions, was found to be optimum when the spacing-to-duct-height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. This relationship is suitable for design under ideal flow conditions. Inlet flow boundary conditions of the jet and approach flow (mainstream) were found to strongly influence mixing performance, but no attempt was made to determine optimum performance under non-ideal conditions. The tests performed do offer some guidance as to expected mixing behavior for several common variables likely to be imposed by hardware constraints. Additionally, in this study it was found that for rows of orifices with opposite centerlines inline, mixing was similar for blockages up to 89 percent (previous crossflow mixing studies concerned with dilution zone configurations, blockages were typically less than 50 percent). Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but blockage must be =50 percent in this configuration. Round hole and "square" orifice shapes had similar performance. Other variations in orifice shape did not substantially augment overall mixing performance. Furthermore an isothermal mixing data set was generated and used by CFDRC as input to a NO(x) inference code.

Liscinsky, D. S.↗

The Turbulent Pressure Spectrum Within the Roughness Sublayer of a Subarctic Forest Canopy

The turbulent static pressure spectrum E pp (k x ) as a function of longitudinal wavenumber k x in the roughness sublayer of forested canopies is of interest to a plethora of problems such as pressure transport in the turbulent kinetic energy budget, pressure pumping from snow or forest floor, and coupling between flow within and above canopies. Long term static pressure measurements above a sub-arctic forested canopy for near-neutral conditions during the winter and spring were collected and analyzed for three snow cover conditions: trees and ground covered with snow, trees are snow free but the ground is covered with snow, and snow free cover. In all three cases, it is shown that E pp (k x ) obeys the attached eddy hypothesis at low wavenumbers (1/δ < k x < 1/z) —with E pp (k x ) ∝ u$^4_*$k$^{-1}_x$ and Kolmogorov scaling in the inertial subrange at higher wavenumbers—with E pp (k x ) ∝ ϵ 4/3 k x -7/3 , where u * is the friction velocity at the canopy top, is the mean turbulent kinetic energy dissipation rate, z is the distance from the snow top, and is the boundary layer depth. The implications of these two scaling laws to the normalized root-mean squared pressure C p = o p /u$^2_*$ and its newly proposed logarithmic scaling with normalized wall-normal distance z/δ are discussed for snow covered and snow free vegetation conditions. The work here also shows that k$^{-1}_x$ the in the E pp (k x ) appears more extensive and robust than its longitudinal velocity counterpart.

Aslan, Toprak [Finnish Meteorological Inst., Helsi↗

Nature-Inspired Motivation for Developing Self-Healable Electrical Insulation

Polymeric aircraft electrical insulation normally degrade by partial discharge with increasing voltage, which causes excessive localized Joule heating in the material and ultimately leads to dielectric failure of the insulator through thermal breakdown. Self-healing insulation may be a viable option to mitigate permanent mechanical degradation, thus increasing the longevity of the material. Instead of relying on catalyst and monomer-filled microcapsules to crack, flow, and cure at the damaged sites described in well-published mechanisms, self-healing through establishment of ionic crosslinks allows for multiple healing events to occur as well as achieving full recovery strength under certain thermal environments. Surlyn®, a commercial ionically-crosslinked material, was investigated as a self-healing insulation candidate based on prior demonstrations of self-healing behavior. Thin films of varying thicknesses were investigated and the effects of thickness on the dielectric strength were evaluated and compared to representative polymer insulators. The effects of thermal conditioning on the recovery strength and healing were observed as a function of time following dielectric breakdown. Moisture absorption was studied to determine if moisture absorption rates in Surlyn® were lower than that of common polyimide insulators. Preliminary data showed that when cut, Surlyn® films lost nearly 60 percent of its original dielectric strength. However, when Surlyn® was cut and subsequently annealed, the films not only re-mended, but also recouped approximately 93 percent of its original dielectric strength, along with 90-97 percent of its mechanical strength.

electrical↗

Differential effects of ambient or diminished CO 2 and O 2 levels on thylakoid membrane structure in light‐stressed plants

Summary Over‐reduction of the photosynthetic electron transport chain may severely damage the photosynthetic apparatus as well as other constituents of the chloroplast and the cell. Here, we exposed Arabidopsis leaves to saturating light either under normal atmospheric conditions or under CO 2 ‐ and O 2 ‐limiting conditions, which greatly increase excitation and electron pressures by draining terminal electron acceptors. The two treatments were found to have very different, often opposing, effects on the structure of the thylakoid membranes, including the width of the granal lumenal compartment. Modulation of the latter is proposed to be related to movements of ions across the thylakoid membrane, which alter the relative osmolarity of the lumen and stroma and affect the partitioning of the proton motive force into its electrical and osmotic components. The resulting changes in thylakoid organization and lumenal width should facilitate the repair of photodamaged photosystem II complexes in response to light stress under ambient conditions, but are expected to inhibit the repair cycle when the light stress occurs concurrently with CO 2 and O 2 depletion. Under the latter conditions, the changes in thylakoid structure are predicted to complement other processes that restrict the flow of electrons into the high‐potential chain, thus moderating the production of deleterious reactive oxygen species at photosystem I.

Tsabari, Onie↗

On a new method for calculating the potential flow past a body of revolution

A new method is presented for obtaining the velocity potential of the flow about a body of revolution moving uniformly in the direction of its axis of symmetry in a fluid otherwise at rest. This method is based essentially on the fact that the form of the differential equation for the velocity potential is invariant with regard to conformal transformation of the meridian plane. By means of the conformal transformation of the meridian profile into a circle a system of orthogonal curvilinear coordinates is obtained, the main feature of which is that one of the coordinate lines is the meridian profile itself. The use of this type of coordinate system yields a simple expression of the boundary condition at the surface of the solid and leads to a rational process of iteration for the solution of the differential equation for the velocity potential. It is shown that the velocity potential for an arbitrary body of revolution may be expressed in terms of universal functions which, although not normal, are obtainable by means of simple quadratures. The general results are applied to a body of revolution obtained by revolving a symmetrical Joukowski profile about its axis of symmetry. A numerical example further serves to illustrate the theory.

Kaplan, Carl↗

Flame propagation under partially-premixed conditions

This study concentrates on developing a better understanding of triple flames. We relax the assumption of zero heat release, address the issue of stabilization, and, in order to investigate the role that heat release plays in flame propagation in partially premixed combustion, we return to a simple flow field and investigate the behavior of flames in a laminar environment. We solve the compressible Navier-Stokes equations in a two-dimensional domain. At the boundaries, we use an inflow boundary condition on the left and nearly-perfect reflective boundary conditions, required to avoid pressure drift, at the outflow and sides. After the flow and flame are initialized, the mixture fraction is varied at the inlet from its uniform stoichiometric value to a tanh profile varying from zero to one. As the mixture fraction gradient reaches the flame surface only the centerline is exposed to the stoichionetric mixture fraction and locally maintains the planar flame speed and reaction rate. Above this point the mixture is fuel rich, and below fuel lean. As a result, these regions of non-unity equivalence ratio burn less, the reaction rate drops, and the local flame speed is reduced. The excess fuel and oxidizer then combine behind the premixed flame along the stoichiometric surface and burn in a trailing diffusion flame. Thus the 'triple' flame refers to the fuel-rich premixed flame, the fuel-lean premixed flame, and the trailing diffusion flame. Due to heat release, the normal velocity across the flame is increased, whereas the tangential component remains unchanged. Far-field flame speed, local flame speed, and their differences are shown as a function of the local mixing thickness. It was also determined that the lateral position of the flame affects stabilization, and the distribution of the reaction rate along the premixed wings of triple flames affects flame propagation.

Ruetsch, Gregory R.↗

Mechanistic Modeling of TEG Dehydrator Emissions in Oil and Gas Industry

This work presents a mechanistic modeling approach for simulating methane emissions from triethylene glycol (TEG) dehydrators used in oil & gas (O&G) operations. The model was developed as a modular component of the Mechanistic Air Emissions Simulator (MAES) tool, incorporating species-specific absorption and emission dynamics through two-level, second-order polynomial regression (PR) models trained on ProMax simulation data: (1) species-level regression models that track the transfer rates of individual gas species within the dehydrator unit streams, and (2) outlet flow stream regression models that predict the fraction of inlet gas distributed among the outlet streams of the dehydrator unit. These behaviors were characterized over a range of glycol circulation ratios, wet gas pressures, and temperatures. The model was validated using root mean square error (RMSE) analysis. The species-level PR achieved low root mean square error (RMSE) values (<0.03) for light hydrocarbon species across all dehydrator components, ranging from 0.0009 for methane to 0.029 for normal pentane. Similarly, the outlet-level PR yielded RMSE values below 0.002 for the dry gas fraction, 0.001 for the flash tank fraction, and 0.002 for the still vent fraction, demonstrating strong agreement between predicted and reference ProMax values. When deployed at field facilities, the model significantly improved MAES-simulated dehydrator emissions, revealing that gas-assisted glycol pump emissions are the dominant contributors to both dehydrator-level and site-level methane emissions under uncontrolled conditions. Further analysis of the 154 dehydrator units reported by operators under the AMI 2024 project showed that 54 units (31%) used gas-driven glycol pumps, of which 6 units (11%) operated with uncontrolled flash tanks, and 22 units (40.7%) were identified as potentially oversized. Of the six dehydrator units with uncontrolled gas-assisted pumps, pump emissions accounted for 90.25% of total dehydrator emissions and 63.10% of total site-level emissions. These findings highlight substantial opportunities for emissions mitigation through equipment upgrades.

MAES↗

Atmosphere stabilization and element recycle in an experimental mouse-algal system

Life support systems based on bioregeneration rely on the control and manipulation of organisms. Experiments conducted with a gas-closed mouse-algal system designed to investigate principles of photosynthetic gas exchange focus primarily on observing gas exchange phenomena under varying algal environmental conditions and secondarily on studying element cycling through compartments of the experimental system. Inherent instabilities exit between the uptake and release of carbon dioxide CO2 and oxygen O2 by the mouse and algae. Variations in light intensity and cell density alter the photosynthetic rate of the algae and enable maintenance of physiologic concentrations of CO2 and O2. Different nitrogen sources (urea and nitrate) result in different algal assimilatory quotients (AQ). Combinations of photosynthetic rate and AQ ratio manipulations have been examined for their potential in stabilizing atmospheric gas concentrations in the gas-closed algal-mouse system. Elemental mass balances through the experimental systems compartments are being studied with the concurrent development of a mathematical simulation model. Element cycling experiments include quantification of elemental flows through system compartments and wet oxidation of system waste materials for use as an algal nutrient source. Oxidized waste products demonstrate inhibitory properties although dilution has been shown to allow normal growth.

Smernoff, David T.↗

A new technique for the measurement of surface shear stress vectors using liquid crystal coatings

Research has recently shown that liquid crystal coating (LCC) color-change response to shear depends on both shear stress magnitude and direction. Additional research was thus conducted to extend the LCC method from a flow-visualization tool to a surface shear stress vector measurement technique. A shear-sensitive LCC was applied to a planar test surface and illuminated by white light from the normal direction. A fiber optic probe was used to capture light scattered by the LCC from a point on the centerline of a turbulent, tangential-jet flow. Both the relative shear stress magnitude and the relative in-plane view angle between the sensor and the centerline shear vector were systematically varied. A spectrophotometer was used to obtain scattered-light spectra which were used to quantify the LCC color (dominant wavelength) as a function of shear stress magnitude and direction. At any fixed shear stress magnitude, the minimum dominant wavelength was measured when the shear vector was aligned with and directed away from the observer; changes in the relative in-plane view angle to either side of this vector/observer aligned position resulted in symmetric Gaussian increases in measured dominant wavelength. Based on these results, a vector measurement methodology, involving multiple oblique-view observations of the test surface, was formulated. Under present test conditions, the measurement resolution of this technique was found to be +/- 1 deg for vector orientations and +/- 5% for vector magnitudes. An approach t o extend the present methodology to full-surface applications is proposed.

Reda, Daniel C.↗

Theoretical Prediction of Microgravity Ignition Delay of Polymeric Fuels in Low Velocity Flows

A new flammability apparatus and protocol, FIST (Forced Flow Ignition and Flame Spread Test), is under development. Based on the LIFT (Lateral Ignition and Flame Spread Test) protocol, FIST better reflects the environments expected in spacebased facilities. The final objective of the FIST research is to provide NASA with a test methodology that complements the existing protocol and provides a more comprehensive assessment of material flammability of practical materials for space applications. Theoretical modeling, an extensive normal gravity data bank and a few validation space experiments will support the testing methodology. The objective of the work presented here is to predict the ignition delay and critical heat flux for ignition of solid fuels in microgravity at airflow velocities below those induced in normal gravity. This is achieved through the application of a numerical model previously developed of piloted ignition of solid polymeric materials exposed to an external radiant heat flux. The model predictions will provide quantitative results about ignition of practical materials in the limiting conditions expected in space facilities. Experimental data of surface temperature histories and ignition delay obtained in the KC-135 aircraft are used to determine the critical pyrolysate mass flux for ignition and this value is subsequently used to predict the ignition delay and the critical heat flux for ignition of the material. Surface temperature and piloted ignition delay calculations for Polymethylmethacrylate (PMMA) and a Polypropylene/Fiberglass (PP/GL) composite were conducted under both reduced and normal gravity conditions. It was found that ignition delay times are significantly shorter at velocities below those induced by natural convection.

Fernandez-Pello, A. C.↗

An overview of the issues: physiological effects of bed rest and restricted physical activity

Reduction of exercise capacity with confinement to bed rest is well recognized. Underlying physiological mechanisms include dramatic reductions in maximal stroke volume, cardiac output, and oxygen uptake. However, bed rest by itself does not appear to contribute to cardiac dysfunction. Increased muscle fatigue is associated with reduced muscle blood flow, red cell volume, capillarization and oxidative enzymes. Loss of muscle mass and bone density may be reflected by reduced muscle strength and higher risk for injury to bones and joints. The resultant deconditioning caused by bed rest can be independent of the primary disease and physically debilitating in patients who attempt to reambulate to normal active living and working. A challenge to clinicians and health care specialists has been the identification of appropriate and effective methods to restore physical capacity of patients during or after restricted physical activity associated with prolonged bed rest. The examination of physiological responses to bed rest deconditioning and exercise training in healthy subjects has provided significant information to develop effective rehabilitation treatments. The successful application of acute exercise to enhance orthostatic stability, daily endurance exercise to maintain aerobic capacity, or specific resistance exercises to maintain musculoskeletal integrity rather than the use of surgical, pharmacological, and other medical treatments for clinical conditions has been enhanced by investigation and understanding of underlying mechanisms that distinguish physical deconditioning from the disease. This symposium presents an overview of cardiovascular and musculoskeletal deconditioning associated with reduced physical work capacity following prolonged bed rest and exercise training regimens that have proven successful in ameliorating or reversing these adverse effects.

NASA Program Space Physiology and Countermeasures↗