Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BASIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

CO 2 storage and potential fault instability in the St. Lawrence Lowlands sedimentary basin (Quebec, Canada): Insights from coupled reservoir-geomechanical modeling

In this paper, coupled reservoir-geomechanical (TOUGH-FLAC) modeling is applied for the first time to the St. Lawrence Lowlands region to evaluate the potential for shear failure along pre-existing high-angle normal faults, as well as the potential for tensile failure in the caprock units (Utica Shale and Lorraine Group). This activity is part of a general assessment of the potential for safe CO 2 injection into a sandstone reservoir (the Covey Hill Formation) within an Early Paleozoic sedimentary basin. Field and subsurface data are used to estimate the sealing properties of two reservoir-bounding faults (Yamaska and Champlain faults). The spatial variations in fluid pressure, effective minimum horizontal stress, and shear strain are calculated for different injection rates, using a simplified 2D geological model of the Becancour area, located ~110 km southwest of Quebec City. The simulation results show that initial fault permeability affects the timing, localization, rate, and length of fault shear slip. Contrary to the conventional view, our results suggest that shear failure may start earlier for a permeable fault than for a sealing fault, depending on the site-specific geologic setting. In simulations of a permeable fault, shear slip is nucleated along a 60 m long fault segment in a thin and brittle caprock unit (Utica Shale) trapped below a thicker and more ductile caprock unit (Lorraine Group) – and then subsequently progresses up to the surface. In the case of a sealing fault, shear failure occurs later in time and is localized along a fault segment (300 m) below the caprock units. The presence of the inclined low-permeable Yamaska Fault close to the injection well causes asymmetric fluid-pressure buildup and lateral migration of the CO 2 plume away from the fault, reducing the overall risk of CO 2 leakage along faults. Finally, fluid-pressure-induced tensile fracturing occurs only under extremely high injection rates and is localized below the caprock units, which remain intact, preventing upward CO 2 migration.

58 GEOSCIENCES↗

Quantifying the effects of pressure management for the Williston basin Brine Extraction and Storage Test (BEST) site using machine learning

Active reservoir management (ARM) through brine extraction can reduce pressure buildup during large-scale implementation of carbon capture and storage (CCS) projects. This study used machine learning (ML)-assisted approaches to analyze bottomhole pressure (BHP) responses to various brine injection and extraction scenarios. Field monitoring data were collected over a 2-year operation period at two injection wells and one extraction well (about 400 meters away) as part of a Brine Extraction and Storage Test (BEST) in the North Dakota portion of the Williston Basin. Injection activities increased the BHPs at the injection wells by around 0.70 MPa (~100 psi) during the operation period. Extraction activities demonstrated the capability to decrease the BHPs at the injection wells by approximately 0.21–0.34 MPa (30–50 psi) depending on the ratio of the extraction and injection well flow rates (the “extraction ratio” – a normalization procedure used in the analysis). The pressure reduction provided by the extraction well equated to 30%–50% of the pressure buildup at the injection well. Furthermore, this work shows how ML analytics can play a key role in estimating reservoir pressure responses for complex injection and extraction activities during pressure management practices of CCS projects.

58 GEOSCIENCES↗

Textured ceramic membranes for desilting and deoiling of produced water in the Permian Basin

Oil production in the Permian Basin gives rise to large volumes of produced water contaminated by silt, emulsified oil, and additives used for enhanced oil recovery. There is intense interest in the design of membrane modules as sustainable alternatives for produced water treatment to enable the reuse of produced water for agricultural applications, injection into aquifers, and redeployment in oil recovery. Here, we report a hierarchically textured cement-based membrane exhibiting orthogonal wettability, specifically, superhydrophilic and underwater superoleophobic characteristics. The in situ formation of ettringite needles accompanied by embedding of glass spheres imbues multiscale texturation to stainless-steel mesh membranes, enabling the separation of silt and oil from produced water at high flux rates (1600 L h -1 ∙m -2 , at ca. 2.7 bar). Oil concentration is reduced as low as 1 ppb with an overall separation efficiency of 99.7% in singlepass filtration. The membranes show outstanding mechanical resilience and retention of performance across multiple cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interferometric SAR modelling of near surface data to improve geological model in the Surat Basin, Australia

Here we present a study on geophysical inverse modelling for subsurface structural properties of an unconventional hydrocarbon site that was monitored previously by Interferometric Synthetic Aperture Radar (InSAR) technology for surface deformation. A static three-dimensional geomodel along with extracted property maps replicates the depth of each underlying stratigraphic unit and structural feature with the density of each geological layer. We examine the hypothesis that integration of elastic properties of each formation layer with InSAR observations in a stratified elastic medium will lead to a viscoelastic geophysical inverse problem that can be solved to estimate fractional volume change at the reservoir level. Moreover, we examine synthetic scenarios in which the elastic properties of the formations are perturbed before determining the resulting impact on the rate of surface deformation. The results show that although the slope of underlying formations, their density and depth can define the extent and pattern of a deformation signal, their properties have a marginal impact on volumetric change compared to the dense network of shallow depth Coal Seam Gas (CSG) mining wells. Besides, it is also demonstrated that the inversion of InSAR deformation maps can resolve the uncertainties associated with low-resolution seismic interpretation as well as filling the data gaps within seismic acquisitions. A significant contribution of this investigation to the geological basin modelling involves a) introducing a remote and non-invasive technology such as InSAR to improve geophysical mapping of subsurface structures such as faults in areas with sparse or no reflective seismic information, and b) applying a multi-layer viscoelastic geophysical source model for an unconventional hydrocarbon reservoir such as CSG.

58 GEOSCIENCES↗

SWAT model application for evaluating agricultural conservation practice effectiveness in reducing phosphorous loss from the Western Lake Erie Basin

Lake Erie is threatened by eutrophication and harmful algal blooms due to excess nutrient loading from agricultural sources. Agricultural conservation practices (ACPs) have been developed and implemented to reduce nutrient losses but estimating ACP effectiveness is challenging. The Soil and Water Assessment Tool (SWAT) has been used to investigate ACP effectiveness for water quality improvement. Many SWAT applications have been developed by different investigators to evaluate ACP effectiveness for reducing nutrient, particularly phosphorus (P), loading in the agriculturally-dominated Western Lake Erie Basin (WLEB). Our objective is to establish what has been achieved by past modeling research and make suggestions for future applications and improvements. We synthesized the findings of 28 SWAT modeling studies within the WLEB. Models generally performed satisfactorily against accepted criteria for streamflow and sediment, but performance for P loads, like soluble reactive P, was mostly “unsatisfactory”. The “unsatisfactory” performance maybe due to imperfections and idealizations in model formulations and/or parameterization. Thus, simulations of P transport and transformation processes need improvement. In addition, model parameter selection is the key part of model set-up. Most SWAT modeling studies used default values during initial set-up, then performed calibration and validation. It was found that the calibrated P related parameter values varied widely across different studies, even within the same watershed with some values unrealistic for the study areas. The phenomena of different combinations of model parameters producing similar outputs indicates equifinality. Equifinality in the baseline model may impact results when ACPs are incorporated. Furthermore, the unrealistic values used in ACP assessment undermine the credibility of ACP effectiveness. Future model applications should try to re-examine the calibrated P parameters and make sure they are realistic for the study area as well as reduce equifinality by constraining the model with characterization of watershed conditions, better understanding of hydrologic processes, and parameter values based on real-world observations. As a result, future model applications should focus on improving P transport and transformation processes, using measured watershed characteristics for parameterization, and improving reflections of climate change, which could result in more accurate assessments of ACP effectiveness to meet targeted goals.

54 ENVIRONMENTAL SCIENCES↗

Improving Hydrological Simulation in the Upper Mississippi River Basin through Enhanced Freeze-Thaw Cycle Representation

Freeze-thaw cycles are important processes relevant to terrestrial hydrological cycling. However, the representation of freeze-thaw cycle has been often simplified in large scale watershed models. The Soil and Water Assessment Tool (SWAT), which has been widely used to understand and assess hydrologic budgets and water resources management, employs a simplified empirical approach to estimate soil temperature and determine the freezing and thawing status of soils. Here, we compared the performance of a physically-based soil temperature module and the built-in empirical approach in SWAT against field measurements at surface and 5, 10, 20, 50, and 100 cm depths at six stations of the U.S. Climate Reference Network (USCRN) within the Upper Mississippi River Basin (UMRB). In general, SWAT consistently underestimated winter soil temperatures and overestimated frozen days at all soil depths, while the modified version of SWAT (equipped with the physically-based soil temperature model; referred to as TSWAT) pronouncedly reduced the bias in estimated winter soil temperatures and frozen days compared with SWAT. Model performance assessment is conducted with three statistical coefficients, i.e., Bias (?), coefficient of determination (R2), and Nash-Sutcliffe coefficient (NS). Statistical analyses show that TSWAT accurately simulated surface and soil temperatures at the five depths with R2 and NS values greater than 0.82 at most sites, and Bias values were generally within the range of -1 to 1? during winter and ranged between -2.09 and 2.58 ? in non-winter seasons. The differences in freeze-thaw cycle representation between SWAT and TSWAT translate into noticeable discrepancies in simulated key hydrologic variables, such as surface runoff, percolation, and baseflow. Compared against long-term observed streamflow (1980-2015), TSWAT outperformed SWAT in capturing variations in monthly streamflow in both winter and non-winter seasons. These results and analyses highlight the value of improving freeze-thaw cycle representation for enhanced hydrologic modeling in large watersheds that are subject to freeze-thaw cycles.

soil temperature, freeze-thaw cycles, streamflow↗

Influence of sampling frequency and estimation method on phosphorus load uncertainty in the Western Lake Erie Basin, Ohio, USA

Accurate estimates of nutrient loads are necessary to identify critical source areas and quantify the impact of management practices on pollutant export. Previous studies have investigated nutrient load estimate uncertainty, but they often focus on nutrient loads estimated using an interpolation method for large-scale watersheds with short-term datasets. The study objective was to quantify uncertainty in soluble reactive phosphorus (SRP), total phosphorus (TP), and suspended solids (SS) load estimates from two small (<10 3 km 2 ) agricultural watersheds in the western Lake Erie Basin resulting from different sampling frequencies. Each watershed had high temporal resolution datasets of discharge (15 min) and nutrient concentration (1 to 3 samples per day) collected over a 30-year period (1990–2020). Firstly, SRP, TP, and SS loads were calculated using the high temporal resolution datasets, which was assumed as “true loads”. Secondly, the high temporal concentration data were decomposed to semiweekly, weekly, biweekly, and monthly sampling and annual loads were estimated using four common load estimation methods to assess the effect of sampling frequency and load estimation method on load estimate error. Across the four different methods, the composite method had the lowest relative root mean square and absolute bias, but the rectangular interpolation method was the most precise. Furthermore, even with semiweekly sampling, the composite method resulted in an unacceptable level of precision (average imprecision = 39 %), while the interpolation method resulted in an unacceptable bias (average absolute bias = 16 %). Because neither method could provide acceptable accuracy and precision at the lowest decrease in sampling (e.t. semiweekly sampling), continued daily sampling is recommended in these watersheds.

54 ENVIRONMENTAL SCIENCES↗

Enhancing SWAT with mechanistic plant hydraulics: development and application in the Hanjiang River Basin

Plant transpiration plays a critical role in global water and energy cycles, requiring better process understanding as climate change intensifies drought stress and alters plant responses. Most hydrological models such as the widely-used SWAT lack representation of plant hydraulics, the mechanistic processes controlling plant water regulation and transpiration. Here, this study developed SWAT-PHS by integrating a plant hydraulics scheme (PHS) into SWAT hydrological model, enabling explicit simulation of root water uptake, sap flow, storage and transpiration at 30-minute timescales for watershed-scale modeling. In the Hanjiang River Basin, SWAT-PHS mitigated overestimation of runoff during the rainy season and underestimation during the dry season, reducing the overall simulation error by 29% across the entire simulation period. The model can simulate reasonable plant water dynamics, including diurnal transpiration patterns and drought responses showing declining transpiration flux, hydraulic buffering through stem water storage, and depth-dependent root water uptake strategies. Sensitivity analysis shows that SWAT-PHS captured mechanistic relationships between plant hydraulic traits and transpiration, with root distribution and stem capacitance positively affecting annual transpiration while vulnerability parameters showed negative effects. This work provides a pathway for improving hydrologic modeling and water resource management by better representing plant water regulation under climate change and expected intensifying water stress conditions.

China↗

The influence of submarine canyons-related processes on recent benthic foraminiferal distribution, Espírito Santo Basin, Southeastern Brazil

The complex topography of submarine canyons may result in different composition of benthic foraminifera assemblages. To understand how trophic, hydrological and sedimentological conditions in submarine canyons can influence the distribution of benthic foraminifera, and to use this information to corroborate paleoenvironmental interpretations for the Holocene, we investigated recent benthic foraminiferal assemblages (total fauna >63 μm) and sedimentological data in two canyons (CANWN and CAND) in the Espírito Santo Basin (ESB) between 18°20' and 21°20' S. Surface sediment samples (0–2 cm) were collected inside the canyons (150 to 1300 m water depth) and in shelf-slope adjacent transects (50 to 1300 m water depth). The density, taxonomic diversity, and assemblage composition of benthic foraminifera change with depth and location. The distinct ecological preferences of the most abundant taxa allowed us to recognize five benthic foraminiferal groups. Three groups (V, III, and I) are present in different bathymetric sectors; Group V: outer shelf (50 m), Group III: upper, and middle – lower slope (150 to 400 m), and Group I: middle – lower slope (1000 to 1300 m). Groups II and IV show no characteristic bathymetric distribution and are present only in CAND and in CANWN, respectively. Group V consists of Hanzawaia boueana, Peneroplis planatus, and Quinqueloculina lamarckiana; Group III is dominated by Globocassidulina rossensis and Trifarina spp.; Group I consists of Globocassidulina crassa, Bolivina lowmani, Gavelinopsis versiformis, Alabaminella weddellensis, and Epistominella exigua. The main species in Group II (CAND, 150, 1000 to 1300 m) are Trifarina angulosa, Globocassidulina subglobosa, and Discorbis vilardeboanus. Group IV (middle – lower CANWN, 1000 to 1300 m), consists mainly of agglutinated species Glomospira charoides, Rhabdammina abyssorum, and Psammosphaera fusca. Further, our data suggest that the quantity (and quality) of food supply, hydrodynamic conditions and sediment properties are the main drivers controlling the bathymetric distribution of benthic foraminiferal assemblages in both canyons. The middle – lower CANNW revealed unstable trophic conditions, related to terrigenous sediment input due to turbidity currents. In CAND, the foraminiferal assemblages ecology indicated sufficient organic matter supply that favors species establishment and diversity, indicating a more productive and less unstable environment than in CANWN.

58 GEOSCIENCES↗

Pressure core analysis of geomechanical and fluid flow properties of seals associated with gas hydrate-bearing reservoirs in the Krishna-Godavari Basin, offshore India

Physical properties of the sediment directly overlying a gas hydrate reservoir provide important controls on the effectiveness of depressurizing that reservoir to extract methane from gas hydrate as an energy resource. The permeability of overlying sediment determines if a gas hydrate reservoir’s upper contact will provide an effective seal that enables efficient reservoir depressurization. Compressibility, stiffness and strength indicate how overlying sediment will deform as the in situ stress changes during production, providing engineering data for well designs. Assessing these properties requires minimally-disturbed sediment. India’s National Gas Hydrates Program Expedition 2 (NGHP-02) provided an opportunity to study these seal sediment properties, reducing disturbance from gas exsolution and bubble growth by collecting a pressure core from the seal sediment just above the primary gas hydrate reservoir at Site NGHP-02-08 in Area C of the Krishna-Godavari Basin. The effective stress chamber (ESC) and the direct shear chamber (DSC) devices in the suite of Pressure Core Characterization Tools (PCCTs) were used to measure permeability, compressibility, stiffness and shear strength at the in situ vertical stress. Geotechnical properties of the predominantly fine-grained seal layer at in situ vertical stress are in typical clay sediment ranges, with low measured permeability (0.02 mD), high compressibility (C c = 0.26 – 0.33) and low shear strength (404 kPa). Though pressure and temperature were maintained throughout the collection and measurement process to stabilize gas hydrate, the lack of effective stress in the pressure core storage chamber and the chamber pressurization with methane-free water caused core expansion and gas hydrate in a thin coarser-grained layer to dissolve. The PCCTs can reapply in situ stress with incremental loading steps during a consolidation test to account for sediment compaction. Lastly, gas hydrate dissolution can be limited by storing cores just above freezing temperatures, and by using solid spacers to reduce the storage chamber’s free volume.

09 BIOMASS FUELS↗

Physical property characteristics of gas hydrate-bearing reservoir and associated seal sediments collected during NGHP-02 in the Krishna-Godavari Basin, in the offshore of India

India’s National Gas Hydrate Program Expedition 02 (NGHP-02) was conducted to better understand geologic controls on gas hydrate occurrence and morphology, targeting coarse-grained sediments along the lower continental slope offshore eastern India. This study combines seismic, logging-while-drilling data, and a petroleum system approach to provide a regional geologic and lithologic context for: 1) gas hydrate morphology and distribution, and 2) effects of fine-grained sediments (clays and other grains smaller than 63µm) on gas production in NGHP-02 Area B in the Krishna-Godavari Basin. Area B seismic data show a buried anticline/syncline structure with strong reflectors, R1 and R2, that delineate two of the five lithologic units: Unit I (shallowest), II (R1), III, IV (R2) and V (below the bas of gas hydrate stability). Throughout Area B, gas hydrate morphology depends on its placement within these units. Specifically, core- and grain-scale measurements indicate fines content exerts a primary control on the gas hydrate distribution and morphology. Units I, II and III are generally fine-grained. On the anticline crest, these units host primarily grain-displacing gas hydrate veins linked to pore-occupying gas hydrate in thin, localized, coarser-grained deposits. Diatoms in Unit III increase porosity with depth, reaching ~70% where it contacts Unit IV, the gas hydrate reservoir associated with reflector R2. The Unit III lithology and porosity allow fluid and dissolved-phase methane to escape Unit IV and form gas hydrate in the fine-grained overburden. Within Unit IV, fine-grained layers are interbedded with coarser-grained gas hydrate reservoir sands, and the fines content even in the sands is high enough to impact hydraulic and mechanical properties during gas production. Fluid motion during gas production can mobilize fines, which can then clog pore throats, limiting production rates. In conclusion, pore-water freshening during gas hydrate dissociation can increase fines mobilization, particularly given the smectite identified in the fine-grained interbeds.

03 NATURAL GAS↗

Evaluation of the performance of the oceanic hydrate accumulation at site NGHP-02-09 in the Krishna-Godavari Basin during a production test and during single and multi-well production scenarios

The objective of this study is to quantify, by means of numerical simulation, the response of the complex system of gas hydrate accumulations at Site NGHP-02-09, Krishna-Godavari Basin, Indian Ocean, to different production conditions, and to determine the technical feasibility of gas production through depressurization-induced dissociation. The study assesses the suitability of the site for a long-term production test involving a single vertical well, and the long-term potential of the deposit under full-field production using a system of multiple vertical wells. We simulate gas and water flow, estimate the production performance of the accumulation and separately investigate the corresponding geomechanical response of the system. Results indicate that production from Site NGHP-02-09 under the conditions of a long-term field test involving a single vertical well is technically feasible and can yield high gas production rates. However, an inability to fully isolate the water bearing zones results in production that is largely from dissolved gas rather than hydrate dissociation and is thus burdened by excessive water production. Given the estimated physical properties of the reservoir system, Site NGHP-02-09 does not appear to be a promising location for a single-well field test of gas production, but may be a promising production target for full-field production operations using a multi-well system in which exterior wells can mitigate water inflows to allow interior wells to more effectively depressurize the formation and capture methane from gas hydrate dissociation. Geomechanical issues need to be carefully considered as significant displacements are possible, which can be challenging to well construction and stability.

58 GEOSCIENCES↗

Analysis of alternative climate datasets and evapotranspiration methods for the Upper Mississippi River Basin using SWAT within HAWQS

This study reports the application of Soil andWater Assessment Tool (SWAT) within the Hydrologic andWater Quality System(HAWQS) on-line platform, for the UpperMississippi River Basin (UMRB). TheUMRB is an important ecosystem located in the north central U.S. that is experiencing a range of ecological stresses. Specifically, testing of SWAT was performed for: (1) Hargreaves (HG) and Penman-Monteith (PM) PET methods, and (2) Livneh, National Climatic Data Center (NCDC) and Parameter-elevation Regressions on Independent Slopes Model (PRISM) climate datasets. The Livneh-PM combination resulted in the highest average annual water yield of 380.6 mm versus the lowest estimated water yield of 193.9 mm for the Livneh-HG combination, in response to 23-year uncalibrated simulations. Higher annual ET and PET values were predicted with HG method versus the PM method for all three weather datasets in response to the uncalibrated simulations, due primarily to higher HG-based estimates during the growing season. Based on these results, it was found that the HG method is the preferred PET option for the UMRB. Initial calibration of SWAT was performed using the Livneh data and HGmethod for threeMississippi Rivermain stem gauge sites, which was followed by spatial validation at 10 other gauge sites located within the UMRB streamnetwork. Overall satisfactory results were found for the calibration and validation gauge sites, with the majority of R2 values ranging between 0.61 and 0.82, Nash- Sutcliffe modeling efficiency (NSE) values ranging between 0.50 and 0.79, and Kling-Gupta efficiency (KGE) values ranging between 0.61 and 0.84. The results of an additional experimental suite of six scenarios,which represented different combinations of climate data sets and calibrated parameters, revealed that suggested statistical criteria were again satisfied by the different scenario combinations. Overall, the PRISM data exhibited the strongest reliability for the UMRB.

54 ENVIRONMENTAL SCIENCES↗

Hydrological projections over the Upper Indus Basin at 1.5 °C and 2.0 °C temperature increase

We analyse an ensemble of statistically downscaled Global Climate Models (GCMs) to investigate future water availability in the Upper Indus Basin (UIB) of Pakistan for the time horizons when the global and/or regional warming levels cross Paris Agreement (PA) targets. The GCMs data is obtained from the 5th Phase of Coupled Model Inter-Comparison Project under two Representative Concentration Pathways (RCP4.5 and RCP8.5). Based on the five best performing GCMs, we note that global 1.5 °C and 2.0 °C warming thresholds are projected in 2026 and 2047 under RCP4.5 and 2022 and 3036 under RCP8.5 respectively while these thresholds are reached much earlier over Pakistan i.e. 2016 and 2030 under RCP4.5 and 2012 and 2025 under RCP8.5 respectively. Interestingly, the GCMs with the earliest emergence at the global scale are not necessarily the ones with the earliest emergence over Pakistan, highlighting spatial non-linearity in GCMs response. The emergence of 2.0 °C warming at global scale across 5 GCMs ranges from 2031 (CCSM4) to 2049 (NorESM) under RCP8.5. Precipitation generally exhibits a progressive increasing trend with stronger changes at higher warming or radiative forcing levels. Hydrological simulations representing the historical, 1.5 °C and 2.0 °C global and region warming time horizons indicate a robust but seasonally varying increase in the inflows. The highest inflows in the baseline and future are witnessed in July. However, the highest future increase in inflows is projected in October under RCP4.5 (37.99% and 65.11% at 1.5 °C and 2.0 °C) and in April under RCP8.5 (37% and 62.05% at 1.5 °C and 2.0 °C). These hydrological changes are driven by increases in the snow and glacial melt contribution, which are more pronounced at 2.0 °C warming level. These findings should help for effective water management in Pakistan over the coming decades.

54 ENVIRONMENTAL SCIENCES↗

Isotopically zoned carbonate cements in Early Paleozoic sandstones of the Illinois Basin: δ 18 O and δ 13 C records of burial and fluid flow

SEM/SIMSimaging andanalysis of δ 18 O and δ 13 C in sandstonesfrom a transect through the Illinois Basin(USA) show systematic μm-scale isotopic zonation of up to 10‰ in both carbonate and quartzcements of the middle-Ordovician St. Peter and Cambrian Mt. Simonformations. Quartz δ 18 O values are broadly consistent with the model of Hyodo et al. (2014), wherein burial and heating in the Illinois Basinis recorded insystematically zonedquartz overgrowths. Observations of zoned dolomite/ankerite cements indicate that they preserve a more extended record of temperature and fluid compositionsthan quartz, including earlydiagenesis before orduring shallow burial,and late carbonates formed after quartzovergrowths. Many carbonate cements show innermostdolomite withδ 18 O values (21-25‰ VSMOW) that are too low to have formed by depositionat low temperatures from ancient seawater(δ 18 O>-3‰)and most likelyreflect mixing with meteoric water. A sharp increase in Fe content is commonly observed in zoned carbonate cements to be associated with a drop in δ 18 O and an abrupt shift in δ 13 C to higher or lower values. These changes are interpreted to record the passage of hot metal-richbrinesthrough sandstone aquifers,that wasassociated with Mississippi-Valley Type (MVT) Pb-Zn deposits (ca. 270 Ma) of the Upper Mississippi Valley. Local variability and individual trends in δ 13 Care likely controlled by the sources of carbon and the degree to which carbonis sourced fromadjacent carbonate units or thermal maturation of organic matter. Quartz overgrowths in sandstones provide an excellent record of conditions during burial, heating, and pressure-solution, whereas carbonate cements in sandstonespreserve a more-extendedrecord includinginitial pre-burial conditions and punctuated fluid flowevents.

58 GEOSCIENCES↗

Differential structure and functional gene response to geochemistry associated with the suspended and attached shallow aquifer microbiomes from the Illinois Basin, IL

Despite the clear ecological significance of the microbiomes inhabiting groundwater and connected ecosystems, our current understanding of their habitats, functionality, and the ecological processes controlling their assembly have been limited. In this study, an efficient pipeline combining geochemistry, high-throughput Fluidigm TM functional gene amplification and sequencing was developed to analyze the suspended and attached microbial communities inhabiting five groundwater monitoring wells in the Illinois Basin, USA. The dominant taxa in the suspended and the attached microbial communities exhibited significantly different spatial and temporal changes in both alpha- and beta-diversity. Further analyses of representative functional genes affiliated with N 2 fixation (nifH), methane oxidation (pmoA), and sulfate reduction (dsrB, and aprA), suggested functional redundancy within the shallow aquifer microbiomes. While more diversified functional gene taxa were observed for the suspended microbial communities than the attached ones except for pmoA, different levels of changes over time and space were observed between these functional genes. Notably, deterministic and stochastic ecological processes shaped the assembly of microbial communities and functional gene reservoirs differently. While homogenous selection was the prevailing process controlling assembly of microbial communities, the neutral processes (e.g., dispersal limitation, drift and others) were more important for the functional genes. The results suggest complex and changing shallow aquifer microbiomes, whose functionality and assembly vary even between the spatially proximate habitats and fractions. As a result, this research underscored the importance to include all the interface components for a more holistic understanding of the biogeochemical processes in aquifer ecosystems, which is also instructive for practical applications.

54 ENVIRONMENTAL SCIENCES↗

Hydrocarbon Recovery from Williston Basin Shale and Mudrock Cores with Supercritical CO 2 : 2. Mechanisms That Control Oil Recovery Rates and CO 2 Permeation

In part 1 (10.1021/acs.energyfuels.9b01177), CO2 was used to recover oil from 51 source shale and reservoir mudrock cores collected from the Bakken Petroleum System in the Williston Basin. Oil hydrocarbon recoveries after 24 hexposures to CO2 at reservoir pressure and temperature were >94% for the reservoir mudrock cores and ranged from a few percent to as much as 80% for the source shales depending on the well location. In part 2, the experimental parameters that control oil recoveries were investigated, and the results show that exposed rock surface areas and CO2 contact times are primary factors controlling oil recovery at reservoir temperature and pressure. Compared to the 11.2 mm diameter rods used in part 1,increasing the surface area by splitting the rods into a stack of 2−3 mm thick “coins” doubled the oil recovery rates from both reservoir and source rocks, while further increasing the surface area using ground and sieved 1−3.4 mm samples at least tripledrecovery rates. In addition, extending the exposure time for the 11.2 mm diameter source shale rods to 96 h yielded nearly complete oil recoveries (as did the 24 h exposures with the 1−3.4 mm samples), indicating that pore spaces in the source shales as well as the more permeable reservoir rocks can be accessed by the CO2 and the associated oil hydrocarbons recovered. Higher CO 2 pressures yielded higher oil recoveries from both the reservoir rocks and source shales regardless of whether the exposure pressure was at or a little below, somewhat above, or substantially above the minimum miscibility pressure (MMP).Laboratory experiments also demonstrated that crude oil recoveries are based primarily on the ability of the CO 2 to penetrate the rock matrix and dissolve the oil hydrocarbons via hydrocarbon vaporization into the CO 2 phase rather than bulk physical processes (e.g., swelling, lowered viscosity, the physical “sweeping” effect) that are important in conventional CO 2 floods. Lighter hydrocarbons (e.g., C7 to C14) were recovered at much faster rates than heavier hydrocarbons (e.g., >C20) from all rock samples and geometries as well as for all CO2 pressures tested, as might be expected because lighter hydrocarbons have both higher diffusion coefficients and higher solubilities in CO 2 than heavier hydrocarbons. Limiting the amount of CO2 had little or no effect on the recovery rates of the lighter hydrocarbons but greatly reduced those of the heavier hydrocarbons. These two observations are consistent with a concentration-gradient-driven diffusion recovery mechanism. Laboratory results suggest that oil recovery in the Bakken play with CO2 will be enhanced by longer soak times, larger exposed rock surface areas, and higher pressures.

Energy & Fuels↗

Midlatitude Ozone Depletion and Air Quality Impacts from Industrial Halogen Emissions in the Great Salt Lake Basin

We report aircraft observations of extreme levels of HCl and the dihalogens Cl 2 , Br 2 , and BrCl in an industrial plume near the Great Salt Lake, Utah. Complete depletion of O 3 was observed concurrently with halogen enhancements as a direct result of photochemically produced halogen radicals. Observed fluxes for Cl 2 , HCl, and NO x agreed with facility-reported emissions inventories. Bromine emissions are not required to be reported in the inventory, but are estimated as 173 Mg year –1 Br 2 and 949 Mg year –1 BrCl, representing a major uncounted oxidant source. A zero-dimensional photochemical box model reproduced the observed O 3 depletions and demonstrated that bromine radical cycling was principally responsible for the rapid O 3 depletion. Inclusion of observed halogen emissions in both the box model and a 3D chemical model showed significant increases in oxidants and particulate matter (PM 2.5 ) in the populated regions of the Great Salt Lake Basin, where winter PM 2.5 is among the most severe air quality issues in the U.S. The model shows regional PM 2.5 increases of 10%–25% attributable to this single industrial halogen source, demonstrating the impact of underreported industrial bromine emissions on oxidation sources and air quality within a major urban area of the western U.S.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗