Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Angle of attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

In-Flight Wing Pressure Distributions for the NASA F/A-18A High Alpha Research Vehicle

Pressure distributions on the wings of the F/A-18A High Alpha Research Vehicle (HARV) were obtained using both flush-mounted pressure orifices and surface-mounted pressure tubing. During quasi-stabilized 1-g flight, data were gathered at ranges for angle of attack from 5 deg to 70 deg, for angle of sideslip from -12 deg to +12 deg, and for Mach from 0.23 to 0.64, at various engine settings, and with and without the leading edge extension fence installed. Angle of attack strongly influenced the wing pressure distribution, as demonstrated by a distinct flow separation pattern that occurred between the range from 15 deg to 30 deg. Influence by the leading edge extension fence was evident on the inboard wing pressure distribution, but little influence was seen on the outboard portion of the wing. Angle-of-sideslip influence on wing pressure distribution was strongest at low angle of attack. Influence of Mach number was observed in the regions of local supersonic flow, diminishing as angle of attack was increased. Engine throttle setting had little influence on the wing pressure distribution.

Davis, Mark C.↗
NASA NTRS1981

Wind-tunnel investigation of the tail-spoiler concept for stall-prevention on general aviation airplanes

The longitudinal aerodynamic characteristics of a full scale, single engine general aviation airplane equipped with an angle of attack limiting concept which used a tail mounted spoiler for stall prevention were investigated. The tail spoiler was deployed as a nonlinear function of changes in angle of attack in a narrow angle of attack range immediately preceding the stall angle. Spoiler deployment produced a nose down moment which limited the nose up trim capability of the elevator to an angle of attack below the stall angle of the airplane. The tail spoiler system produced significant increases in longitudinal stability and elevator hinge moments near the stall. The effects of power, flaps, and center of gravity position are also studied.

Satran, D. R.↗
NASA NTRS1993

Experimental effects of wing location on wing-body pressures at supersonic speeds

An experimental study was performed at supersonic speeds to measure wing and body spanwise pressure distributions on an axisymmetric-body delta wing model on which the wing vertical location on the body was systematically varied from low- to high-mounted positions. In addition, for two of these positions both horizontal and radial wing angular orientations relative to the body were tested, and roll angle effects were investigated for one of the positions. Seven different wing-body configurations and a body-alone configuration were studied. The test was conducted at Mach numbers from 1.70 to 2.86 at angles of attack from about -4 deg to 24 deg. Pressure orifices were located at three longitudinal stations on each wing-body model, and at each station the orifices were located completely around the body, along the lower surface of the right wing (looking upstream), and along the upper surface of the left wing. All pressure coefficient data are tabulated and selected samples are shown graphically to illustrate the effects of the test variables. The effects of angle of attack, roll angle, Mach number, longitudinal station, wing vertical location, wing angular orientation, and wing-body juncture are analyzed. The vertical location of the wing on the body had a very strong effect on the body pressures. For a given angle of attack at a roll angle of 0 deg, the pressures were virtually constant in the spanwise direction across the windward surfaces of the wing-body combination. Pressure-relieving, channeling, and vortex effects were noted in the data.

Allen, Jerry M.↗
NASA NTRS1975

An investigation in the NASA MSFC 14-inch trisonic wind tunnel to determine the pressure distribution over the components of a 0.004 scale version of the Rockwell MCR 0074 baseline shuttle ascent configuration (IA32F), volume 1

Data were obtained for Mach numbers from 0.6 to 3.48, angles of attack from -10 to 10 degrees, and angles of sideslip from -10 to 10 degrees at zero angle of attack. Also, -4 and 4 degrees sideslip were run for an angle of attack of -5 and 5 degrees. Aerodynamic configurations of the solid rocket motors, external tank, and orbiter are shown. Graphs of plotted pressure data (pressure coefficients) for the external tank and solid rocket motors are given. A description of the test facility is included.

Ramsey, P. E.↗
NASA NTRS1977

Supersonic aerodynamic characteristics of a series of wrap-around-fin missile configurations

A parametric study of wrap-around-fin missile configurations was conducted at Mach numbers from 1.60 to 2.86 in the Langley Unitary Plan wind tunnel. The fin configurations investigated included variations in chord length, leading edge sweep, thickness ratio, and leading edge shape. The investigation also included a smooth and a stepped-down afterbody required for flush retraction of the wrap-around-fin configuration. The investigation indicated no unusual longitudinal characteristics; however, all the wrap-around-fin configurations tested indicated erratic lateral behavior, particularly in the form of induced roll at zero angle of attack and irregular variations of roll with angle of attack and Mach number. The magnitude of rolling moment at an angle of attack of 0 deg is estimated to represent approximately 0.25 deg or less roll control deflection. The stepped-down afterbody has a marked effect on reducing the induced roll.

Fournier, R. H.↗
NASA NTRS1994

Computational Investigation of an F-18 Aircraft in the High-Alpha Regime

One of the goals of NASA's High Alpha Technology Program is to provide flight-validated design methods for the high-angle-of-attack regime. This is an integrated effort utilizing computational simulations, wind tunnel experiments, and flight tests using the F-18 High Alpha Research Vehicle (HARV). The dominant physics of the aircraft flows in the high alpha regime changes as the angle of attack is increased. At moderate angle of attack the flow is characterized by boundary layer separation and the formation of tight vortices. As the angle of attack is increased, these vortices break down producing unsteady wakes. With further increase in angle of attack, the, vortex breakdown moves progressively upstream until the entire flowfield becomes dominated by the unsteady wake. Previous computational work has demonstrated the ability to simulate flows about the F-18 HARV in the medium-to-high angle of attack range, where the flowfield is characterized by the vortex formation and subsequent breakdown. This paper extends the previous computations to include conditions of 45 degree angle of attack where the flowfield becomes dominated by the unsteady wake shed from the Leading Edge Extension (LEX), and regions of laminar and transitional flow appear on the fuselage forebody. A more complete surface geometry is utilized, which includes the features of the engine nacelle, inlet diffuser, and the boundary layer diverter duct. A volume grid sensitivity study was also performed to extend the accuracy of the results, most notably in the prediction of the LEX vortex breakdown position. This paper includes comparisons of computational results with both in-flight surface pressure measurements, and flow visualizations of the surface and off-surface particle trajectories.

Murman, Scott M.↗
NASA NTRS1999

An Inviscid Computational Study of an X-33 Configuration at Hypersonic Speeds

This report documents the results of a study conducted to compute the inviscid longitudinal aerodynamic characteristics of a simplified X-33 configuration. The major components of the X-33 vehicle, namely the body, the canted fin, the vertical fin, and the body-flap, were simulated in the CFD (Computational Fluid Dynamic) model. The rear-ward facing surfaces at the base including the aerospike engine surfaces were not simulated. The FELISA software package consisting of an unstructured surface and volume grid generator and two inviscid flow solvers was used for this study. Computations were made for Mach 4.96, 6.0, and 10.0 with perfect gas air option, and for Mach 10 with equilibrium air option with flow condition of a typical point on the X-33 flight trajectory. Computations were also made with CF4 gas option at Mach 6.0 to simulate the CF4 tunnel flow condition. An angle of attack range of 12 to 48 deg was covered. The CFD results were compared with available wind tunnel data. Comparison was good at low angles of attack; at higher angles of attack (beyond 25 deg) some differences were found in the pitching moment. These differences progressively increased with increase in angle of attack, and are attributed to the viscous effects. However, the computed results showed the trends exhibited by the wind tunnel data.

Prabhu, Ramadas K.↗
NASA NTRS2020

Comparison of Aerocapture Performance Using Bank Control and Direct Force Control with Two Human-Scale Vehicles at Mars

Recent studies of human-scale missions to Mars have included a wide trade space of vehicle configurations and control schemes. Some configurations fly at a low angle of attack with a low L/D,while others fly at a high angle of attack with a mid L/D. Some use bank angle control, while others use direct force control, where the angle of attack and sideslip angle are independently modulated. This paper compares the performance of three vehicle configurations: a low-L/D vehicle using direct force control, a low-L/D vehicle using bank control, and a mid-L/D vehicle using bank control. The reference mission is aerocapture at Mars into a highly elliptical, 1-sol orbit. The trajectories are integrated in three degrees of freedom. All three cases utilize numeric predictor-corrector guidances and emulate control system responses with rate and acceleration limits. The configurations are compared using a Monte Carlo analysis. The robustness of each configuration to increased dispersions is also compared.

Matz, Daniel A.↗
NASA NTRS1981

Experimental investigation of vortices shed by various wing fin configurations

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

Iversen, J.↗
NASA NTRS1983

Subsonic roll oscillation experiments on the Standard Dynamics Model

The experimental determination of the subsonic roll derivatives of the Standard Dynamics Model, which is representative of a current fighter aircraft configuration, is described. The direct, cross and cross-coupling derivatives are presented for angles of attack up to 41 deg and sideslip angles in the range from -5 deg to 5 deg, as functions of oscillation frequency. The derivatives exhibited significant nonlinear trends at high incidences and were found to be extremely sensitive to sideslip angle at angles of attack near 36 deg. The roll damping and dynamic cross derivatives were highly frequency dependent at angles of attack above 30 deg. The highest values measured for the dynamic cross and cross-coupling derivatives were comparable in magnitude with the maximum roll damping. The effects of oscillation amplitude and Mach number were also investigated, and the direct derivatives were correlated with data from another facility.

Beyers, M. E.↗
NASA NTRS1987

An experimental study of the aerodynamic characteristics of planar and non-planar outboard wing planforms

A series of wind tunnel experiments have been conducted to investigate the aerodynamic characteristics of several planar and nonplanar wingtip planforms. Seven different configurations: base-line rectangular, elliptical, swept and tapered, swept and tapered with dihedral, swept and tapered with anhedral, rising arc, and drooping arc, were investigated for two different spans. The data are available in terms of coefficient plots of force data, flow visualization photographs, and velocity and pressure flowfield surveys. All planforms, particularly the nonplanar, have some advantages over the baseline rectangular planform. Span efficiencies up to 20-percent greater than baseline are a possibility. However, it is suggested that the span efficiency concept might need refinement for nonplanar wings. Flow survey data show the change in effective span with vortex roll-up. The flow visualization shows the occurrence of mushroom-cell-separation flow patterns at angles of attack corresponding to stall. These grow with an increase in post-stall angle of attack. For the larger aspect ratios, the cells are observed to split into sub-cells at the higher angles of attack. For all angles of attack, some amount of secondary vortex flow is observed for the planar and nonplanar out-board planforms with sweep and taper.

Naik, D. A.↗
NASA NTRS1983

Wing modification for increased spin resistance

A simple wing leading-edge modification has been developed that delays outer wing panel stall, thus maintaining roll damping to higher angles of attack and delaying the onset of autorotation. The stall angle of attack of the outer wing panel has been shown to be a function of the spanwise length of the leading-edge modification. The margin of spin resistance provided by the modification is being explored through flight tests. Preliminary results have been used to evaluate spin resistance in terms of the difference in angle of attack between outer wing panel stall and the maximum attainable angle of attack.

Stough, H. P.↗
NASA NTRS1945

Wind-Tunnel Tests of a 1/6-Scale Model of Republic XF-12 Vertical Tail with Stub Fuselage and Stub Horizontal Tail

A 1/6-scale model of the Republic XF-12 vertical tail with stub fuselage and stub horizontal tail was tested in the Langley stability tunnel to determine the aerodynamic characteristics of the model, The investigation included a study of the effects of boundarylayer thickness, rudder area, and cover-plate alinement on the aerodynamic characteristics. Tuft studies were made in the vicinity of the junction of the vertical and stub horizontal tails. The results of the investigation indicated that the flow in the vicinity of the junction of the vertical and stub horizontal tails was only slightly improved by the addition of a fillet. An increase in boundary-layer thickness produced a slight decrease in rudder effectiveness. The increase in lift of the combined rudders over that of the upper rudder alone was not proportional at low deflections and was approximately proportional at high deflections to the increase in rudder area. When the balance-chamber cover plates were bowed out, the change in rudder hinge moment with rudder angle was less negative. The variation of the lift coefficient with angle of attack and the variation, at small values of angle of attack, of rudder hinge-noment coefficient with angle of attack was approximately the same for all model configurations tested. The upper rudder used in conjunction with a tab was found to satisfy the Army specifications regarding asymmetric power on a multiengine airplane.

MacLachlan, Robert↗
NASA NTRS2009

Flight Dynamics of an Aeroshell Using an Attached Inflatable Aerodynamic Decelerator

An aeroelastic analysis of the behavior of an entry vehicle utilizing an attached inflatable aerodynamic decelerator during supersonic flight is presented. The analysis consists of a planar, four degree of freedom simulation. The aeroshell and the IAD are assumed to be separate, rigid bodies connected with a spring-damper at an interface point constraining the relative motion of the two bodies. Aerodynamic forces and moments are modeled using modified Newtonian aerodynamics. The analysis includes the contribution of static aerodynamic forces and moments as well as pitch damping. Two cases are considered in the analysis: constant velocity flight and planar free flight. For the constant velocity and free flight cases with neutral pitch damping, configurations with highly-stiff interfaces exhibit statically stable but dynamically unstable aeroshell angle of attack. Moderately stiff interfaces exhibit static and dynamic stability of aeroshell angle of attack due to damping induced by the pitch angle rate lag between the aeroshell and IAD. For the free-flight case, low values of both the interface stiffness and damping cause divergence of the aeroshell angle of attack due to the offset of the IAD drag force with respect to the aeroshell center of mass. The presence of dynamic aerodynamic moments was found to influence the stability characteristics of the vehicle. The effect of gravity on the aeroshell angle of attack stability characteristics was determined to be negligible for the cases investigated.

Cruz, Juan R.↗
NASA NTRS1992

Origin And Behavior Of Asymmetric Vortices

Report presents theoretical study of vortices shed by ogive/cylinder body of revolution facing oncoming flow at various angles of attack. Study focuses attention on two phenomena observed in prior computer numerical simulations of such flows: mean flow that is asymmetrical, at moderate to high angle of attack, about plane containing angle of attack; and fluctuations at higher angles of attack.

Tobak, Murray↗
NASA NTRS2019

Computational Analysis of the External Aerodynamics of the Unpowered X-57 Mod-III Aircraft

Investigations of the external aerodynamics of the unpowered X-57 Mod-III configuration using computational fluid dynamics are presented. Two different Reynolds-averaged Navier-Stokes flow solvers were used in the analysis: the STAR-CCM+ unstructured solver using polyhedral grid topology, and the Launch Ascent Vehicle Aerodynamics (LAVA) structured curvilinear flow solver using structured overset grid topology. A grid refinement study was conducted and suitable grid resolution was determined by examining the forces and moments of the aircraft. Code-to-code comparison shows that STAR-CCM+ and LAVA are in good agreement both in quantitative values and trends. The angle-of-attack sweep and sideslip-angle sweep were performed. Results indicate that lift coefficients have a sharp drop at stall. At high angle of attack, STAR-CCM+ and LAVA show different flow separation behavior possibly due to differences in the turbulence model. The sideslip-angle sweep results show constant pitching moment from 0° to 15°, then a sharp increase between 15° and 20° sideslip angle.

Yoo, Seung Y.↗
NASA NTRS2017

Inviscid/Boundary-Layer Aeroheating Approach for Integrated Vehicle Design

A typical entry vehicle design depends on the synthesis of many essential subsystems, including thermal protection system (TPS), structures, payload, avionics, and propulsion, among others. The ability to incorporate aerothermodynamic considerations and TPS design into the early design phase is crucial, as both are closely coupled to the vehicle's aerodynamics, shape and mass. In the preliminary design stage, reasonably accurate results with rapid turn-representative entry envelope was explored. Initial results suggest that for Mach numbers ranging from 9-20, a few inviscid solutions could reasonably sup- port surface heating predictions at Mach numbers variation of +/-2, altitudes variation of +/-10 to 20 kft, and angle-of-attack variation of +/- 5. Agreement with Navier-Stokes solutions was generally found to be within 10-15% for Mach number and altitude, and 20% for angle of attack. A smaller angle-of-attack increment than the 5 deg around times for parametric studies and quickly evolving configurations are necessary to steer design decisions. This investigation considers the use of an unstructured 3D inviscid code in conjunction with an integral boundary-layer method; the former providing the flow field solution and the latter the surface heating. Sensitivity studies for Mach number, angle of attack, and altitude, examine the feasibility of using this approach to populate a representative entry flight envelope based on a limited set of inviscid solutions. Each inviscid solution is used to generate surface heating over the nearby trajectory space. A subset of a considered in this study is recommended. Results of the angle-of-attack sensitivity studies show that smaller increments may be needed for better heating predictions. The approach is well suited for application to conceptual multidisciplinary design and analysis studies where transient aeroheating environments are critical for vehicle TPS and thermal design. Concurrent prediction of aeroheating environments, coupled with the use of unstructured methods, is considered enabling for TPS material selection and design in conceptual studies where vehicle mission, shape, and entry strategies evolve rapidly.

Lee, Esther↗
NASA NTRS1972

Supersonic aerodynamic damping and oscillatory stability in pitch and yaw fro a model of a variable-sweep fighter airplane with twin vertical tails

Wind-tunnel measurements of the aerodynamic damping and oscillatory in pitch and yaw for a 1/22-scale model of a proposed carrier-based variable-sweep fighter airplane have been made by using a small-amplitude forced-oscillation technique. Tests were made with a wing leading-edge sweep angle of 68 deg at angles of attack from about -1.5 deg to 15.6 deg at a Mach number of 1.60 and at angles of attack from about -3 deg to 21 deg at Mach numbers of 2.02 and 2.36. The results of the investigation indicate that the basic configuration has positive damping and positive oscillatory stability in pitch for all test conditions. In yaw, the damping is generally positive except near an angle of attack of 0 deg at a Mach number of 1.60. The oscillatory stability in yaw is positive except at angles of attack above 16 deg at Mach numbers of 2.02 and 2.36. The addition of external stores generally causes increases in both pitch and yaw damping. The oscillatory stability in pitch is reduced throughout the angle-of-attack range by the addition of the external stores. The effect of adding stores on the oscillatory stability in yaw is a function of angle of attack and Mach number. The effect of changing horizontal-tail incidence on the pitch parameters is also very dependent on angle of attack and Mach number.

Kilgore, R. A.↗