Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Investigation of Polymer Induced Fouling of Heater Tubes in the First-Ever Polymer Flood Pilot on Alaska North Slope

Mineral fouling in heat exchangers has been extensively investigated by researchers in recent times. The oil and gas industry has a long history of fouling issues in production systems as a result of produced fluids treatment. Due to decline in production rates in oilfields new technologies are being developed and field tested in pilots. Polymer flooding is one such technology that involves addition of polymers to injection fluids to enhance oil production. A polymer flood pilot has been set up in the Schrader Bluff viscous oil reservoir at Milne Point field on the Alaska North Slope (ANS). The results from the pilot are encouraging, however a major concern of the operator is the influence of polymer on the production system after breakthrough, especially the fouling in heat exchangers. This study investigates the propensity of polymer fouling on the heater tubes as a function of different variables, with the ultimate goal of determining safe and efficient operating conditions. This work applies a multi-experimental approach to study the severity of polymer-induced fouling in both dynamic and static states of produced fluids as well as studying the stability of polymer solutions at different temperatures. A unique experimental setup was designed and developed in-house to simulate the fouling process on the heating tube. The influence of heating tube skin temperature, tube material, and polymer concentration on fouling tendency was investigated. Each test was run five times with the same tube, and in each run, the freshly prepared synthetic brine and polymer solution was heated from 77°F to 122°F to mimic field-operating conditions. The heating time and fouling amount were recorded for each run. Dynamic Scale Loop (DSL) tests were conducted to study fouling due to polymer at different temperatures (165°F to 350°F) in a dynamic state of fluid flow where the fluids mimic the residence time of fluids in the heat exchanger on the field pilot. Cloud point measurement has also been conducted to find the critical temperature at which the polymer in solution becomes unstable and precipitates out. The morphology and composition of the deposit samples were analyzed by environmental scanning electron microscopy (ESEM) and X-ray diffraction (XRD), respectively. It was found that the presence of polymer in produced fluids would aggravate the fouling issues on both carbon steel and stainless-steel surfaces at all tested skin temperatures. Only higher skin temperatures of 250°F and 350°F could cause polymer-induced fouling issues on the copper tube surface, and the fouling tendency increased with polymer concentration. At the lower skin temperatures of 165°F, no polymer-induced fouling was identified on the copper tube. A critical temperature that is related to the cloud point of the polymer solution was believed to exist, below which polymer-induced fouling would not occur, and only mineral scale was deposited but above which the polymer would aggravate the fouling issue. The cloud point of the tested polymer solution was determined to be between 220°F and 230°F. In the DSL tests it was found that at higher skin temperatures of 250°F and 350°F tube blocking was observed in the DSL tests whereas the tests at 165°F and 200°F did not show any tube blocking in the same time period. These experiments also manifested the influence of cloud point of the solution as deposit rate increased significantly in both carbon steel and stainless-steel tubes when the skin temperature was higher than the solution cloud point. The results of this study have provided guidance to the operator for the field-operations.

Dhaliwal, Anshul↗
DOE OSTI2021

Uncovering the Relationship between Aging and Cycling on Lithium Metal Battery Self-Discharge

Lithium metal is considered the “holy grail” material to replace typical Li-ion anodes due to the absence of a host structure coupled with a high theoretical capacity. The absence of a host structure results in large volumetric changes when lithium is electrodeposited/dissolved, making the lithium prone to stranding and parasitic reactions with the electrolyte. Lithium research is focused on enabling highly reversible lithium electrodeposition/dissolution, which is important to achieving long cycle life. Understanding the various mechanisms of self-discharge is also critical for realizing practical lithium metal batteries but is often overlooked. In contrast to previous work, it is shown here that self-discharge via galvanic corrosion is negligible, particularly when lithium is cycled to relevant capacities. Rather, the continued electrochemical cycling of lithium metal results in self-discharge when periodic rest is applied during cycling. The extent of self-discharge can be controlled by increasing the capacity of plated lithium, tuning electrolyte chemistry, incorporating regular rest, or introducing lithiophilic materials. Finally, the Coulombic losses that occur during periodic rest are largely reversible, suggesting that the dominant self-discharge mechanism in this work is not an irreversible chemical process but rather a morphological process.

25 ENERGY STORAGE↗
DOE OSTI2024

Unsupervised learning-enabled pulsed infrared thermographic microscopy of subsurface defects in stainless steel

Metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing method (AM) frequently contain microscopic porosity defects, with typical approximate size distribution from one to 100 microns. Presence of such defects could lead to premature failure of the structure. In principle, structural integrity assessment of LPBF metals can be accomplished with nondestructive evaluation (NDE). Pulsed infrared thermography (PIT) is a non-contact, one-sided NDE method that allows for imaging of internal defects in arbitrary size and shape metallic structures using heat transfer. PIT imaging is performed using compact instrumentation consisting of a flash lamp for deposition of a heat pulse, and a fast frame infrared (IR) camera for measuring surface temperature transients. However, limitations of imaging resolution with PIT include blurring due to heat diffusion, sensitivity limit of the IR camera. We demonstrate enhancement of PIT imaging capability with unsupervised learning (UL), which enables PIT microscopy of subsurface defects in high strength corrosion resistant stainless steel 316 alloy. PIT images were processed with UL spatial–temporal separation-based clustering segmentation (STSCS) algorithm, refined by morphology image processing methods to enhance visibility of defects. The STSCS algorithm starts with wavelet decomposition to spatially de-noise thermograms, followed by UL principal component analysis (PCA), fine-tuning optimization, and neural learning-based independent component analysis (ICA) algorithms to temporally compress de-noised thermograms. The compressed thermograms were further processed with UL-based graph thresholding K-means clustering algorithm for defects segmentation. The STSCS algorithm also includes online learning feature for efficient re-training of the model with new data. For this study, metallic specimens with calibrated microscopic flat bottom hole defects, with diameters in the range from 203 to 76 µm, were produced using electro discharge machining (EDM) drilling. While the raw thermograms do not show any material defects, using STSCS algorithm to process PIT images reveals defects as small as 101 µm in diameter. To the best of our knowledge, this is the smallest reported size of a sub-surface defect in a metal imaged with PIT, which demonstrates the PIT capability of detecting defects in the size range relevant to quality control requirements of LPBF-printed high-strength metals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of diffusion constant on the morphology of dendrite growth in lithium metal batteries

Lithium dendrites can lead to a short circuit and battery failure, and developing strategies for their suppression is of considerable importance. In this work, we study the growth of dendrites in a simple model system where the solvent is a continuum and the lithium ions are hard spheres that can deposit by sticking to existing spheres or the electrode surface. Using stochastic dynamics simulations, we investigate the effect of applied voltage and diffusion constant on the growth of dendrites. We find that the diffusion constant is the most significant factor, and the inhomogeneity of the electric field does not play a significant role. Additionally, the growth is most pronounced when the applied voltage and diffusion constant are both low. We observe a structural change from broccoli to cauliflower shape as the diffusion constant is increased. The simulations suggest that a control of electrolyte parameters that impact lithium diffusion might be an attractive route to controlling dendrite growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

High-Throughput Automated Exploration of Phase Growth Behaviors in Quasi-2D Formamidinium Metal Halide Perovskites

Quasi-2D metal halide perovskites (MHPs) are an emerging material platform for sustainable functional optoelectronics, but the uncontrollable, broad phase distribution remains a critical challenge for applications. Nevertheless, the basic principles for controlling phases in quasi-2D MHPs remain poorly understood, due to the rapid crystallization kinetics during the conventional thin-film fabrication process. In this work, a high-throughput automated synthesis-characterization-analysis workflow is implemented to accelerate material exploration in formamidinium (FA)-based quasi-2D MHP compositional space, revealing the early-stage phase growth behaviors fundamentally determining the phase distributions. Upon comprehensive exploration with varying synthesis conditions including 2D:3D composition ratios, antisolvent injection rates, and temperatures in an automated synthesis-characterization platform, it is observed that the prominent n = 2 2D phase restricts the growth kinetics of 3D-like phases—α-FAPbI 3 MHPs with spacer-coordinated surface—across the MHP compositions. Thermal annealing is a critical step for proper phase growth, although it can lead to the emergence of unwanted local PbI 2 crystallites. Additionally, fundamental insights into the precursor chemistry associated with spacer-solvent interaction determining the quasi-2D MHP morphologies and microstructures are demonstrated. The high-throughput study provides comprehensive insights into the fundamental principles in quasi-2D MHP phase control, enabling new control of the functionalities in complex materials systems for sustainable device applications.

2D perovskites↗
DOE OSTI2023

Phase field modeling of shearing processes of a dual-lobed γ"|γ'|γ" coprecipitate

The Ni-based superalloy IN718 is one of the most widely used commercial alloy in the aerospace industry since its development in 1960s. The excellent mechanical properties have been attributed in a great deal to strengthening by coherent γ' and γ" precipitates. The deformation mechanisms of these two phases have been well studied individually. Recent experimental characterization has shown coprecipitates of these two phases in a variety of morphologies and it was argued that these coprecipitates may lead to improved strengthening as compared to their monolithic counterparts. However, the deformation mechanisms of these coprecipitates are still not well understood. In this study, we performed microscopic phase field simulations, with generalized-stacking-fault (GSF) energy surfaces from ab initio calculations as inputs, to systematically study the shearing processes of a periodical array of dual-lobed coprecipitates as well as monolithic precipitates. We found that the coupling between the γ' and γ" phases in the coprecipitates forces dislocations to take high energy shearing pathways in both phases that would not occur if they were in monolithic forms. The coupling also creates stacking fault configurations in the coprecipitates that require high stress to form. Thus, the presence of coprecipitates in general should increase the resistance to dislocation shearing and lead to higher strength levels. Various fault configurations observed during the shearing process are documented as a reference for future comparison with experimental observations. The link between stacking fault shearing and microtwinning is also discussed. Here, the mechanisms analyzed in this study deepens our understanding of coprecipitation effects on alloy strength and may form a cornerstone for multi-precipitate strengthened alloy design strategies.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Geometric control of magnetic domain morphology in electrodeposited Ni rich NiPt mesoscopic wires

In this paper, we study the electrodeposited Ni—Pt magnetic wires, exploring the mechanisms by which changes in geometry and composition influence the local magnetic structure. The samples were prepared by electrodeposition, their elemental composition was analyzed by energy dispersive X-ray spectroscopy, and phase analysis was carried out by an X-ray diffraction measurement. Magnetic force microscopy measurements, and magnetic force microscopy measurements in magnetic field were carried out to study the domain morphology of the prepared samples. Magnetization characteristics were measured via vibrating sample magnetometry mode of a superconducting quantum interference device. Here, the results were analyzed and compared with micromagnetic simulations. It is shown that a strong perpendicular magnetic anisotropy is responsible for the characteristic checkerboard-like surface magnetization patterns, which can be tuned by geometrical constriction and Ni content. Understanding these relationships provides insights into the design of magnetic materials with tailored properties for advanced applications, like magnetic sensors.

Binary alloy↗
DOE OSTI2021

Li + Diffusion in Amorphous and Crystalline Al 2 O 3 for Battery Electrode Coatings

Al 2 O 3 is often applied protectively to lithium-ion battery anode and cathode materials to inhibit surface degradation, suppress dendrite formation, and relieve mechanical stresses. Given the very high intrinsic band gap and diffusion barrier of the material, the mechanism that allows Li diffusion through these coatings is not well understood, and widely varying laboratory results indicate that there may be dependencies on morphology and stoichiometry. Using nudged elastic band calculations and ab initio molecular dynamics, we perform a systematic investigation across Al 2 O 3 structures, both crystalline and amorphous, and at various concentrations of Li + to uncover the optimal parameters for maximally diffusive coatings. We find a correlation between the low proximity of Li + to Al 3+ and the low Li + migration barrier. Although barriers are the lowest in the highly diffusive one-dimensional channels of crystalline θ-Al 2 O 3 , the system is structurally delicate and subject to detrimental distortion as the Li + content is increased. The α-Al 2 O 3 lattice is, conversely, highly stable against distortion at all Li + concentrations but disadvantageous for Li + migration. In amorphous systems, unscreened Li + –Li + Coulomb repulsion and pre-emptive occupation of “trapping sites” combine to lower the energy barriers as a function of increasing concentration. One of our most important findings is that Al-deficient materials can sharply increase Li + movement, and we predict that an amorphous material with a combination of high Li + concentration and Al deficiency would enable highly Li + -conductive protective coatings for electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Failure Process During Fast Charging of Lithium Metal Batteries with Weakly Solvating Fluoroether Electrolytes

While improving the lithium metal (Li) Coulombic efficiency has been a focus for electrolyte design, the performance under high current densities is less studied yet highly relevant for practical applications. Here, we evaluate the charge-rate-dependent cycling stability using three types of weakly solvating fluoroether electrolytes. Although good cycle life was achieved in all three electrolytes under low current densities, they all exhibited a soft shorting behavior above various threshold current densities (between 2 and 5.2 mA cm –2 ). In this study, we attributed the current-dependent electrode morphology to both Li growth and residual solid electrolyte interface (rSEI) growth processes. In early cycles, Li morphology guided the formation of rSEI structures. In later cycles, the rSEI structure partially impacted Li growth. Under low current densities, the rSEI was inhomogeneous with large voids for subsequent bulky lithium growth. Under high current densities, the rSEI became more dense, which aggravated the high-surface/volume-ratio Li growth through and on the top of the rSEI. Among the three weakly solvating fluoroether electrolytes, the ones with lower ionic conductivity were observed to short within fewer cycles and at lower charge current densities. Our work suggests that fast ion transport in electrolytes may be a desirable feature for the stable operation at >1C charging in high-energy-density lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Modification of cell wall polysaccharide guides cell division in Streptococcus mutans

In ovoid-shaped, Gram-positive bacteria, MapZ guides FtsZ-ring positioning at cell equators. The cell wall of the ovococcus Streptococcus mutans contains peptidoglycan decorated with serotype c carbohydrates (SCCs). In the present study, we identify the major cell separation autolysin AtlA as an SCC-binding protein. AtlA binding to SCC is attenuated by the glycerol phosphate (GroP) modification. Using fluorescently labeled AtlA constructs, we mapped SCC distribution on the streptococcal surface, revealing enrichment of GroP-deficient immature SCCs at the cell poles and equators. The immature SCCs co-localize with MapZ at the equatorial rings throughout the cell cycle. In GroP-deficient mutants, AtlA is mislocalized, resulting in dysregulated cellular autolysis. These mutants display morphological abnormalities associated with MapZ mislocalization, leading to FtsZ-ring misplacement. Altogether, our data support a model in which maturation of a cell wall polysaccharide provides the molecular cues for the recruitment of cell division machinery, ensuring proper daughter cell separation and FtsZ-ring positioning.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Particle emission with identification from an atmospheric pressure plasma liquid interface

A conspicuous emission phenomenon of luminous particles from the liquid anode surface of an atmospheric pressure DC glow discharge is reported. The emission has been shown to occur when the plasma forms a pattern on the surface of the liquid electrolyte. Here, the spatial-temporal evolutions of the trajectories of emitted particles were studied using a high-speed imaging system. Particles were sampled in flight using a witness plate for analysis. Critical particle characteristics were examined using electron microscope technologies. The morphology of the resulting splats and compositions suggest that they are molten droplets with a great deal of structure, including evidence of nanoprecipitation. A theoretical model was employed to estimate the particle size from the measured splats, which provides a radius range within a hundred micrometers. This experiment leads to the postulation of a mechanism in which particle emission at the plasma liquid interface is likely driven by the Taylor cone effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Crystal structure engineering in multimetallic high-index facet nanocatalysts

Significance Crystal structure engineering in nanoparticles represents an important strategy in catalyst design, as catalytic performance is highly dependent on atomic arrangement. However, realizing crystal structure engineering in high-index facet nanocatalysts has been a synthetic challenge for decades. Here, we first employed density functional theory calculations to determine whether surface modifications can stabilize high-index facets during crystal structure transformations and then synthesized a library of multimetallic high-index facet tetrahexahedral (THH) nanoparticles with controllable crystal structures. Importantly, the crystal structural transition between the intermetallic and chemically disordered states is reversable, and the THH morphology of nanocatalysts is maintained during this transformation. This approach broadens the synthetic scope of nanocatalysts available for use in diverse chemical processes.

Shen, Bo↗
DOE OSTI2024

Facet-dependent dispersion and aggregation of aqueous hematite nanoparticles

Nanoparticle aggregates in solution controls surface reactivity and function. Complete dispersion often requires additive sorbents to impart a net repulsive interaction between particles. Facet engineering of nanocrystals offers an alternative approach to produce monodisperse suspensions simply based on facet-specific interaction with solvent molecules. Here, we measure the dispersion/aggregation of three morphologies of hematite (α-Fe 2 O 3 ) nanoparticles in varied aqueous solutions using ex situ electron microscopy and in situ small-angle x-ray scattering. We demonstrate a unique tendency of (104) hematite nanoparticles to maintain a monodisperse state across a wide range of solution conditions not observed with (001)- and (116)-dominated particles. Density functional theory calculations reveal an inert, densely hydrogen-bonded first water layer on the (104) facet that favors interparticle dispersion. Results validate the notion that nanoparticle dispersions can be controlled through morphology for specific solvents, which may help in the development of various nanoparticle applications that rely on their interfacial area to be highly accessible in stable suspensions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Controlled Fabrication of Quality ZnO NWs/CNTs and ZnO NWs/Gr Heterostructures via Direct Two-Step CVD Method

A novel and advanced approach of growing zinc oxide nanowires (ZnO NWs) directly on single-walled carbon nanotubes (SWCNTs) and graphene (Gr) surfaces has been demonstrated through the successful formation of 1D–1D and 1D–2D heterostructure interfaces. The direct two-step chemical vapor deposition (CVD) method was utilized to ensure high-quality materials’ synthesis and scalable production of different architectures. Iron-based universal compound molecular ink was used as a catalyst in both processes (a) to form a monolayer of horizontally defined networks of SWCNTs interfaced with vertically oriented ZnO NWs and (b) to grow densely packed ZnO NWs directly on a graphene surface. We show here that our universal compound molecular ink is efficient and selective in the direct synthesis of ZnO NWs/CNTs and ZnO NWs/Gr heterostructures. Heterostructures were also selectively patterned through different fabrication techniques and grown in predefined locations, demonstrating an ability to control materials’ placement and morphology. Several characterization tools were employed to interrogate the prepared heterostructures. ZnO NWs were shown to grow uniformly over the network of SWCNTs, and much denser packed vertically oriented ZnO NWs were produced on graphene thin films. Such heterostructures can be used widely in many potential applications, such as photocatalysts, supercapacitors, solar cells, piezoelectric or thermal actuators, as well as chemical or biological sensors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Tribological Behavior of Structural Materials in High Temperature Helium Gas-Cooled Reactor Environments

The High-Temperature Gas-cooled Reactor (HTGR) is a Generation IV concept designed to produce electricity and hydrogen at high efficiencies via high operating temperatures (700 °C or higher). Helium, the primary coolant for HTGRs, contains impurities (e.g., CO, H2O and CH4) that can induce corrosion reactions at high temperatures such as oxidation and (de)carburization, which in turn can affect the tribological behavior of components. Incoloy® 800HT (Ni-Fe-Cr austenitic solid-solution alloy) and Inconel® 617 (Ni-Cr-Co-Mo solid-solution alloy) are two high-temperature superalloys currently selected as candidate structural materials for the HTGR. The objective of this study is to evaluate the high-temperature tribological performance of these two candidate alloys after conditioning them in HTGR environments. Four regimes of corrosion were considered: a non-conditioned regime (Regime I), an oxidizing regime (Regime II), a carburizing and oxidizing regime (Regime III), and a carburizing regime (Regime IV). To simulate oxidation in HTGR, samples were conditioned for 22 days at elevated temperatures in a once-through helium loop with 4 ppmv H2O. Carburization of the samples was achieved by the commercial process, Kolsterising®. In addition, two surface treatments – shot peening and aluminization – were considered as potential routes of improving the alloys’ wear resistance. Surface-treated samples were tested both before and after conditioning in Regime II. Tribological testing of the samples was performed via a pin-on-disk tribometer at elevated temperatures in ambient environment – 650 and 750°C for 800HT; 850 and 900°C for 617 – with applied loads of 1N, 2N and 5N. The wear behavior of the alloys was assessed via wear volume and friction coefficient measurements, supported by morphological, structural and compositional analyses of the wear tracks. Conditioning the samples in Regime II led to the formation of a chromium oxide on both alloys. This protective scale increased the wear resistance compared to that of as-received samples (Regime I) due to the formation of a compacted ‘glaze’ oxide layer during sliding, rendering the wear track nearly undistinguishable from the unworn background and resulting in wear volumes below the detection limits of the measurement technique. The variability of the friction coefficients of the conditioned samples was also considerably reduced compared to that of the as-received samples due to the glaze layer. Additionally, the initial friction coefficients of the samples conditioned in Regime II were reduced by 45% and 54% compared to those of as-received samples for alloys 800HT and 617, respectively. Carburizing the samples (Regime IV) hardened the surfaces of both alloys and promoted the formation of an iron oxide on 800HT during tribological testing, thereby increasing the wear resistance and decreasing the initial friction coefficient by a factor of two compared to those of as-received 800HT. Alloy 617 exhibited an enhanced wear resistance but similar initial friction coefficient compared to those of as-received samples due to the increased surface hardness. The Mn-Cr oxide developed during Regime III conditioning of 800HT did not develop a glaze layer during tribotesting, even at lower loads. Thus, it was not as protective as the oxide produced during conditioning of Regime II samples, leading to lower wear resistance of 800HT in Regime III compared to that measured in the Regime II condition. 800HT benefited from the aluminization surface treatment, particularly before conditioning in Regime II, due to the promotion of a wear-resistant aluminum oxide layer during testing and the increase in surface hardness due to the presence of a FeAl intermetallic phase. The presence of this phase caused an order-of-magnitude reduction in wear volumes compared to those of as-received 800HT. Aluminization of 617 decreased its wear resistance, particularly after conditioning in Regime II, due to significant wear of the aluminum oxide via a ceramic wear mechanism. This aluminum oxide was removed during sliding, causing the wear volumes to increase by a factor of five compared to those of 617 conditioned in Regime II. Shot-peened 800HT exhibited a tribological behavior similar to that of as-received 800HT, despite an enhancement in the rate of chromium oxide formation. Shot-peened 800HT conditioned in Regime II showed lower wear resistance compared to that of 800HT conditioned in Regime II due to the poor adhesion between the oxide and the underlying metal, preventing the formation of the glaze layer during sliding. Shot peening of 617 increased its wear resistance at higher load, reducing worn volumes by 60% compared to that measured with as-received 617. Tribotesting of shot-peened 617 in Regime II revealed that the glaze-oxide layer was formed at every load, resulting in negligible wear, similar to what was observed from testing 617 after conditioning in Regime II. Overall, alloy 617 exhibited tribologically superior behavior compared to that of alloy 800HT, as demonstrated by its lower friction coefficients and its order-of-magnitude lower wear volumes when measurable.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Arctic Soil Patterns Analogous to Fluid Instabilities: Supporting Data

This dataset characterizes solifluction lobe morphology and spatial patterns using pre-existing LiDAR-derived digital elevation models of 25 sites across Norway with accompanying long term climate data for each site. Data were collected as part of an effort to better understand controls on the formation of solifluction patterns and to test the idea that they are analogous to fluid instabilities. We also provide soil velocity profiles and estimates of effective viscosity from across the world, drawn from literature. They were collected to improve our understanding of the rheology of soliflucting soil. See this article for more information on the theoretical motivation behind this dataset see "Arctic soil patterns analogous to fluid instabilities" (Glade et al., 2021). Data files arranged in a hierarchy and include image files *.tif and *.png, GIS shapefiles and geopackages (*.gpkg), *.csv (with same file as *.xlsx), and *.py (Python scripts readable with a text editor). Files also bundled into *.zip files. Note (2021-10-20): unit corrections made on two files: RR.csv and snowfall.csv. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Heterogeneous Morphologies and Hardness of Co-Sputtered Thin Films of Concentrated Cu-Mo-W Alloys

Heterogeneous microstructures in Cu-Mo-W alloy thin films formed by magnetron co-sputtering immiscible elements with concentrated compositions are characterized using scanning transmission electron microscopy (STEM) and nanoindentation. In this work, we modified the phase separated structure of a Cu-Mo immiscible system by adding W, which impedes surface diffusion during film growth. The heterogeneous microstructures in the Cu-Mo-W ternary system exhibited bicontinuous matrices and agglomerates composed of Mo(W)-rich phase. This is unique, as these are the slower-diffusing species, contrasting past reports of binary Cu-Mo thin films that exhibited Cu-rich agglomerates. The bicontinuous matrices comprised of Cu-rich and Mo(W)-rich phases exhibited bilayer thicknesses of less than 5 nm. The hardness of these thin films measured using nanoindentation is reported and compared to similar multilayers and nanocomposites in binary systems.

36 MATERIALS SCIENCE↗