Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface complexation modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

HST observations of the inner coma of Comet Levy 1990c

Data reduction procedures which will make it possible to model the nucleus of future targets of cometary space missions were tested on the basis of observations of Comet Levy 1990c by the HST on September 27, 1990. Faint hemispherical shells expanding in the coma, which is structured as a sunward fan deflected by solar radiation pressure, were observed. The Eddington fountain model makes it possible to infer the ejection times of the expanding shells and the initial velocity of the dust. Three shells ejected at time intervals of 11.5 and 12.5 h with an initial velocity of 0.35 km/s were observed for dust grains of 3-micron size. The lag angle of the fan is between 10 and 15 deg, thus suggesting a time delay of the most active sublimation of 1 h after midday. The observed time periodicities suggest a nucleus rotating in 24 h with a surface characterized by two active areas placed almost exactly in opposite hemispheres, even if a longer rotation period and a more complex nucleus topography can be excluded.

Fulle, M.↗
NASA NTRS1993

Installed F/A-18 inlet flow calculations at 60 deg angle-of-attack and 10 deg side slip

This paper presents the results of PARC3D numerical calculations on a 19.78 percent scale forebody/inlet model of the F/A-18 at a Mach number of 0.20, an angle-of-attack of 60 deg, and a side-slip angle of 10 deg. The main purpose of these calculations is to support an upcoming wind-tunnel test program in the prediction of engine inlet compressor face total pressure recovery and flow distortion. The GRIDGEN system was used to generate a grid which includes the inlet and lip, and other aircraft components which are considered to be important to inlet performance, such as the ramp/splitter plate, the diverter and slot, and the deflected leading edge flap. PARC3D shows complex flow patterns on the fuselage surfaces below the leading edge extensions, on the ramp/splitter plate, inlet lip, and inside the inlet. PARC3D tends to underpredict total pressure recovery and overpredict the flow distortion at the inlet compressor face.

Podleski, S. D.↗
NASA NTRS1999

Combustion of Metals in Reduced-Gravity and Extra Terrestrial Environments

The combustion of metals is a field with important practical applications in rocket propellants, high-temperature flames, and material synthesis. Also, the safe operation of metal containers in high-pressure oxygen systems and with cryogenic fuels and oxidizers remains an important concern in industry. The increasing use of metallic components in spacecraft and space structures has also raised concerns about their flammability properties and fire suppression mechanisms. In addition, recent efforts to embark on unmanned and manned planetary exploration, such as on Mars, have also renewed the interest in metal/carbon-dioxide combustion as an effective in situ resource utilization technology. In spite of these practical applications, the understanding of the combustion properties of metals remains far behind that of the most commonly used fuels such as hydrocarbons. The lack of understanding is due to the many problems unique to metal- oxidizer reactions such as: low-temperature surface oxidation prior to ignition, heterogeneous reactions, very high combustion temperatures, product condensation, high emissivity of products, and multi-phase interactions. Very few analytical models (all neglecting the influence of gravity) have been developed to predict the burning characteristics and the flame structure details. Several experimental studies attempting to validate these models have used small metal particles to recreate gravity-free conditions. The high emissivity of the flames, rapid reaction, and intermittent explosions experienced by these particles have made the gathering of any useful information on burning rates and flame structure very difficult. The use of a reduced gravity environment is needed to clarify some of the complex interactions among the phenomena described above. First, the elimination of the intrusive buoyant flows that plague all combustion phenomena is of paramount importance in metal reactions due to the much higher temperatures reached during combustion. Second, a low-gravity environment is absolutely essential to remove the destructive effect of gravity on the shape of a molten metal droplet in order to study a spherically symmetric condition with large bulk samples. The larger size of the spherical metal droplet and the longer burning times available in reduced gravity extend the spatial and temporal dimensions to permit careful probing of the flame structure and dynamics. Third, the influence of the radiative heat transfer from the solid oxides can be studied more carefully by generating a stagnant spherical shell of condensed products undisturbed by buoyancy.

Branch, M.C.↗
NASA NTRS2000

Case Studies of the Vertical Structure of the Direct Shortwave Aerosol Radiative Forcing During TARFOX

The vertical structure of aerosol-induced radiative flux changes in the Earth's troposphere affects local heating rates and thereby convective processes, the formation and lifetime of clouds, and hence the distribution of chemical constituents. We present observationally-based estimates of the vertical structure of direct shortwave aerosol radiative forcing for two case studies from the Tropospheric Aerosol Radiative Forcing Observational Experiment (TARFOX) which took place on the US East coast in July 1996. The aerosol radiative forcings are computed using the Fu-Liou broadband radiative transfer model. The aerosol optical properties used in the radiative transfer simulations are calculated from independent vertically-resolved estimates of the complex aerosol indices of refraction in two to three distinct vertical layers, using profiles of in situ particle size distributions measured aboard the University of Washington research aircraft. Aerosol single-scattering albedos at 450 nm thus determined range from 0.9 to 0.985, while the asymmetry factor varies from 0.6 to 0.8. The instantaneous shortwave aerosol radiative forcings derived from the optical profiles of the aerosols are of the order of -36 W/sq m at the top of the atmosphere and about -56 W/sq m at the surface for both case studies.

Redemann, J.↗
NASA NTRS2003

Jell-Molds and Cookie-cutters: Shrinkwrap Isn't Just for Leftovers Anymore

So what is Shrinkwrap all about? For those of you who may not know about it, Shrinkwrap is a type of data structure that can manifest itself as a feature or model. It is cleverly covered up, almost hidden, and doesn't get the press or widespread use of a solid or surface. The shrinkwrap feature is located under the data sharing submenu of the feature menu. The shrinkwrap feature, as described by PTC, is a collection of surfaces and datum features of a model that represents the exterior of the model . The advantages and applications of the shrinkwrap feature are in the creation of minimal memory guzzling representations of assemblies. These can be used to represent subassemblies in parent assemblies, and can handle control of dependency issues, geometry represented, and additional references through the use of the shrinkwrap feature options. The shrinkwrap model is an option available under the save as umbrella. Its function, as described by PTC, is to share data with internal and external design groups and improve performance in large assembly design . Some of the benefits of the shrinkwrap model include being able to represent complex assemblies with a single, lightweight part that protects design intent and parametric data, and the ability to improve performance of large assembly modeling in the area of less load time. The proper-scale models can be saved as IGES, STEP, and VRML (for fly-throughs).

Randazzo, John↗
NASA NTRS2018

Simulation of Sound Absorption by Scattering Bodies Treated with Acoustic Liners Using a Time-Domain Boundary Element Method

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for aircraft noise reduction, and are characterized by a complex valued frequency-dependent impedance, Z(w). Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering of geometric bodies treated with acoustic liners. This work uses an admittance boundary condition where the admittance, Y(w), is defined to be the inverse of impedance, i.e., Y(w) = 1/Z(w). An admittance boundary condition will be derived and coupled with a time domain boundary integral equation. The solution will be obtained iteratively using spatial and temporal basis functions and will allow for acoustic scattering problems to be modeled with geometries consisting of both unlined and soft surfaces. Stability will be demonstrated through eigenvalue analysis.

Pizzo, Michelle E.↗
NASA NTRS2019

Stellar Activity Effects on Moist Habitable Terrestrial Atmospheres Around M Dwarfs

Transit spectroscopy of terrestrial planets around nearby M dwarfs is a primary goal of space missions in coming decades. 3-D climate modeling has shown that slow-synchronous rotating terrestrial planets may develop thick clouds at the substellar point, increasing the albedo. For M dwarfs with T(eff) > 3000 K, such planets at the inner habitable zone (IHZ) have been shown to retain moist greenhouse conditions, with enhanced stratospheric water vapor (fH2O > 10(exp -3)) and low Earth-like surface temperatures. However, M dwarfs also possess strong UV activity, which may effectively photolyze stratospheric H2O. Prior modeling efforts have not included the impact of high stellar UV activity on the H2O. Here, we employ a 1-D photochemical model with varied stellar UV, to assess whether H2O destruction driven by high stellar UV would affect its detectability in transmission spectroscopy. Temperature and water vapor profiles are taken from published 3-D climate model simulations for an IHZ Earth-sized planet around a 3300 K M dwarf with an N2-H2O atmosphere; they serve as self-consistent input profiles for the 1-D model. We explore additional chemical complexity within the 1-D model by introducing other species into the atmosphere. We find that as long as the atmosphere is well-mixed up to 1 mbar, UV activity appears to not impact detectability of H2O in the transmission spectrum. The strongest H2O features occur in the JWST MIRI instrument wavelength range and are comparable to the estimated systematic noise floor of ~50 ppm.

Mahmuda Afrin Badhan↗
NASA NTRS1984

Structure and evolution of the large scale solar and heliospheric magnetic fields

Structure and evolution of large scale photospheric and coronal magnetic fields in the interval 1976-1983 were studied using observations from the Stanford Solar Observatory and a potential field model. The solar wind in the heliosphere is organized into large regions in which the magnetic field has a componenet either toward or away from the sun. The model predicts the location of the current sheet separating these regions. Near solar minimum, in 1976, the current sheet lay within a few degrees of the solar equator having two extensions north and south of the equator. Soon after minimum the latitudinal extent began to increase. The sheet reached to at least 50 deg from 1978 through 1983. The complex structure near maximum occasionally included multiple current sheets. Large scale structures persist for up to two years during the entire interval. To minimize errors in determining the structure of the heliospheric field particular attention was paid to decreasing the distorting effects of rapid field evolution, finding the optimum source surface radius, determining the correction to the sun's polar field, and handling missing data. The predicted structure agrees with direct interplanetary field measurements taken near the ecliptic and with coronameter and interplanetary scintillation measurements which infer the three dimensional interplanetary magnetic structure. During most of the solar cycle the heliospheric field cannot be adequately described as a dipole.

Hoeksema, J. T.↗
NASA NTRS2000

Case Studies of the Vertical Structure of the Direct Shortwave Aerosol Radiative Forcing During TARFOX

The vertical structure of aerosol-induced radiative flux changes in the Earth's troposphere affects local heating rates and thereby convective processes, the formation and lifetime of clouds, and hence the distribution of chemical constituents. We present observationally based estimates of the vertical structure of direct shortwave aerosol radiative forcing for two case studies from the Tropospheric Aerosol Radiative Forcing Observational Experiment (TARFOX) which took place on the U.S. east coast in July 1996. The aerosol radiative forcings are computed using the Fu-Liou broadband radiative transfer model. The aerosol optical properties used in the radiative transfer simulations are calculated from independent vertically resolved estimates of the complex aerosol indices of refraction in two to three distinct vertical layers, using profiles of in situ particle size distributions measured aboard the University of Washington research aircraft. Aerosol single-scattering albedos at 450 nm thus determined range from 0.9 to 0.985, while the asymmetry factor varies from 0.6 to 0.8. The instantaneous shortwave aerosol radiative forcings derived from the optical properties of the aerosols are of the order of -36 Wm(exp -2) at the top of the atmosphere and about -56 Wm(exp -2) at the surface for both case studies.

Redemann, J.↗
NASA NTRS2007

A Time-Accurate Upwind Unstructured Finite Volume Method for Compressible Flow with Cure of Pathological Behaviors

A time-accurate, upwind, finite volume method for computing compressible flows on unstructured grids is presented. The method is second order accurate in space and time and yields high resolution in the presence of discontinuities. For efficiency, the Roe approximate Riemann solver with an entropy correction is employed. In the basic Euler/Navier-Stokes scheme, many concepts of high order upwind schemes are adopted: the surface flux integrals are carefully treated, a Cauchy-Kowalewski time-stepping scheme is used in the time-marching stage, and a multidimensional limiter is applied in the reconstruction stage. However even with these up-to-date improvements, the basic upwind scheme is still plagued by the so-called "pathological behaviors," e.g., the carbuncle phenomenon, the expansion shock, etc. A solution to these limitations is presented which uses a very simple dissipation model while still preserving second order accuracy. This scheme is referred to as the enhanced time-accurate upwind (ETAU) scheme in this paper. The unstructured grid capability renders flexibility for use in complex geometry; and the present ETAU Euler/Navier-Stokes scheme is capable of handling a broad spectrum of flow regimes from high supersonic to subsonic at very low Mach number, appropriate for both CFD (computational fluid dynamics) and CAA (computational aeroacoustics). Numerous examples are included to demonstrate the robustness of the methods.

Loh, Ching Y.↗
NASA NTRS1981

An experimental and computational investigation of the transport of Reynolds stress in an axisymmetric swirling boundary layer

A coordinated experimental and computational investigation of the transport and interaction of the individual Reynolds stresses within a turbulent axisymmetric swirling boundary layer flowing over a stationary cylinder is described. The cylinder is instrumented with new directional surface fence skin-friction gages developed for the experiment. The longitudinal and transverse mean velocity profiles are measured with a miniature directional pressure probe. These data provided a standard on which to compare computed results employing a variety of turbulence models. The turbulence models tested range from a simple mixing length model, through a two-equation model, on to the Reynolds stress equation models. The full Reynolds stress equation models are tested with various sets of modeling coefficients for the pressure rate-of-strain correlation. It is shown that while even the simplest model shows the general features of the data, agreement with the experimental data is enhanced through the use of the more complex models. For a better prediction of the data, however, further model improvement is still required.

Higuchi, H.↗
NASA NTRS1991

Light scattering by lunar-like particle size distributions

A fundamental input to models of light scattering from planetary regoliths is the mean phase function of the regolith particles. Using the known size distribution for typical lunar soils, the mean phase function and mean linear polarization for a regolith volume element of spherical particles of any composition were calculated from Mie theory. The two contour plots given here summarize the changes in the mean phase function and linear polarization with changes in the real part of the complex index of refraction, n - ik, for k equals 0.01, the visible wavelength 0.55 micrometers, and the particle size distribution of the typical mature lunar soil 72141. A second figure is a similar index-phase surface, except with k equals 0.1. The index-phase surfaces from this survey are a first order description of scattering by lunar-like regoliths of spherical particles of arbitrary composition. They form the basis of functions that span a large range of parameter-space.

Goguen, Jay D.↗
NASA NTRS1997

Hierarchical Modeling and Robust Synthesis for the Preliminary Design of Large Scale Complex Systems

Large-scale complex systems are characterized by multiple interacting subsystems and the analysis of multiple disciplines. The design and development of such systems inevitably requires the resolution of multiple conflicting objectives. The size of complex systems, however, prohibits the development of comprehensive system models, and thus these systems must be partitioned into their constituent parts. Because simultaneous solution of individual subsystem models is often not manageable iteration is inevitable and often excessive. In this dissertation these issues are addressed through the development of a method for hierarchical robust preliminary design exploration to facilitate concurrent system and subsystem design exploration, for the concurrent generation of robust system and subsystem specifications for the preliminary design of multi-level, multi-objective, large-scale complex systems. This method is developed through the integration and expansion of current design techniques: Hierarchical partitioning and modeling techniques for partitioning large-scale complex systems into more tractable parts, and allowing integration of subproblems for system synthesis; Statistical experimentation and approximation techniques for increasing both the efficiency and the comprehensiveness of preliminary design exploration; and Noise modeling techniques for implementing robust preliminary design when approximate models are employed. Hierarchical partitioning and modeling techniques including intermediate responses, linking variables, and compatibility constraints are incorporated within a hierarchical compromise decision support problem formulation for synthesizing subproblem solutions for a partitioned system. Experimentation and approximation techniques are employed for concurrent investigations and modeling of partitioned subproblems. A modified composite experiment is introduced for fitting better predictive models across the ranges of the factors, and an approach for constructing partitioned response surfaces is developed to reduce the computational expense of experimentation for fitting models in a large number of factors. Noise modeling techniques are compared and recommendations are offered for the implementation of robust design when approximate models are sought. These techniques, approaches, and recommendations are incorporated within the method developed for hierarchical robust preliminary design exploration. This method as well as the associated approaches are illustrated through their application to the preliminary design of a commercial turbofan turbine propulsion system. The case study is developed in collaboration with Allison Engine Company, Rolls Royce Aerospace, and is based on the Allison AE3007 existing engine designed for midsize commercial, regional business jets. For this case study, the turbofan system-level problem is partitioned into engine cycle design and configuration design and a compressor modules integrated for more detailed subsystem-level design exploration, improving system evaluation. The fan and low pressure turbine subsystems are also modeled, but in less detail. Given the defined partitioning, these subproblems are investigated independently and concurrently, and response surface models are constructed to approximate the responses of each. These response models are then incorporated within a commercial turbofan hierarchical compromise decision support problem formulation. Five design scenarios are investigated, and robust solutions are identified. The method and solutions identified are verified by comparison with the AE3007 engine. The solutions obtained are similar to the AE3007 cycle and configuration, but are better with respect to many of the requirements.

Koch, Patrick N.↗
NASA NTRS2004

Exposure and Terrestrial Histories of New Lunar and Martian Meteorites

Cosmogenic nuclide studies of lunar and Martian meteorites have contributed significantly to our understanding of these objects. By measuring a combination of cosmogenic stable- and radionuclides, we can determine a number of important properties of those meteorites. Most lunar meteorites have complex cosmic ray exposure histories, having been exposed both at some depth on the lunar surface (2 irradiation) before their ejection and as small bodies in space (4 irradiation) during transport from the Moon to the Earth. On the other hand, we have not observed evidence of complex exposure history for any Martian meteorites, so far. These exposures were then followed by residence on Earth s surface, a time commonly referred to as the terrestrial age. In addition to their complement of galactic cosmic ray (GCR) produced nuclides some lunar and Martian meteorites contain nuclides produced by solar cosmic rays (SCR). Unraveling the complex history of these objects requires the measurement of at least four cosmogenic nuclides. The specific goals of these measurements are to constrain or set limits on the following shielding or exposure parameters: (1) the depth of the sample at the time of ejection from the Moon or Mars; (2) the transit time (4 exposure age) from ejection off the lunar or Martian surface to the time of capture by the Earth and (3) the terrestrial residence time. The sum of the transit time and residence time yield an ejection age. The ejection age, in conjunction with the sample depth on the Moon or Mars, can then be used to model impact and ejection mechanisms.

Nishiizumi, K.↗
NASA NTRS2003

Light Scattering by Gaussian Particles: A Solution with Finite-Difference Time Domain Technique

The understanding of single-scattering properties of complex ice crystals has significance in atmospheric radiative transfer and remote-sensing applications. In this work, light scattering by irregularly shaped Gaussian ice crystals is studied with the finite-difference time-domain (FDTD) technique. For given sample particle shapes and size parameters in the resonance region, the scattering phase matrices and asymmetry factors are calculated. It is found that the deformation of the particle surface can significantly smooth the scattering phase functions and slightly reduce the asymmetry factors. The polarization properties of irregular ice crystals are also significantly different from those of spherical cloud particles. These FDTD results could provide a reference for approximate light-scattering models developed for irregular particle shapes and can have potential applications in developing a much simpler practical light scattering model for ice clouds angular-distribution models and for remote sensing of ice clouds and aerosols using polarized light. (copyright) 2003 Elsevier Science Ltd. All rights reserved.

Sun, W.↗
NASA NTRS2013

Sample Analysis at Mars Instrument Simulator

The Sample Analysis at Mars Instrument Simulator (SAMSIM) is a numerical model dedicated to plan and validate operations of the Sample Analysis at Mars (SAM) instrument on the surface of Mars. The SAM instrument suite, currently operating on the Mars Science Laboratory (MSL), is an analytical laboratory designed to investigate the chemical and isotopic composition of the atmosphere and volatiles extracted from solid samples. SAMSIM was developed using Matlab and Simulink libraries of MathWorks Inc. to provide MSL mission planners with accurate predictions of the instrument electrical, thermal, mechanical, and fluid responses to scripted commands. This tool is a first example of a multi-purpose, full-scale numerical modeling of a flight instrument with the purpose of supplementing or even eliminating entirely the need for a hardware engineer model during instrument development and operation. SAMSIM simulates the complex interactions that occur between the instrument Command and Data Handling unit (C&DH) and all subsystems during the execution of experiment sequences. A typical SAM experiment takes many hours to complete and involves hundreds of components. During the simulation, the electrical, mechanical, thermal, and gas dynamics states of each hardware component are accurately modeled and propagated within the simulation environment at faster than real time. This allows the simulation, in just a few minutes, of experiment sequences that takes many hours to execute on the real instrument. The SAMSIM model is divided into five distinct but interacting modules: software, mechanical, thermal, gas flow, and electrical modules. The software module simulates the instrument C&DH by executing a customized version of the instrument flight software in a Matlab environment. The inputs and outputs to this synthetic C&DH are mapped to virtual sensors and command lines that mimic in their structure and connectivity the layout of the instrument harnesses. This module executes, and thus validates, complex command scripts prior to their up-linking to the SAM instrument. As an output, this module generates synthetic data and message logs at a rate that is similar to the actual instrument.

Benna, Mehdi↗
NASA NTRS2020

Charged Particle Dynamics in the Lunar Environment

As the Artemis Program streams forward, organizations of scientists and engineers across the country have been coming together to solve the complex network of problems to once again achieve the milestone of successfully touching down on the moon. This project is no exception, and it has been an honor to work with the Electrostatics and Surface Physics Laboratory (ESPL), a lab within the Exploration Research and Technology Programs’ Spaceport Technologies Office (UB-G) located at the National Aeronautics and Space Administration at Kennedy Space Center (NASA KSC). The authors and their mentor James R. Phillips III3, in tandem with researchers from the Astrodynamics and Space Robotics Laboratory (ASRL) at the University of Central Florida (UCF), have been working on creating a state-of-the-art (SOA) granular gas dynamics model for particulate contamination prevention and mitigation purposes. In essence, the underlying objective for this project is to more accurately model the resulting electrodynamic interactions between lunar regolith grains with applications to dust mitigation and rocket engine plume surface interactions. To achieve this goal, the team has been expanding upon existing open source classical molecular dynamics code developed by Sandia National Laboratories (SNL). The following reports on the details of the problem at hand as well as the contributions that the authors have made towards resolution, including but not limited to the encoding of physical attributes and interactions for non-spherical polydisperse particle distributions within various bed geometries and preemptive data analysis implementations. Significant data analysis processes were utilized, and several original algorithms were created to perform critical evaluations, resulting in only a 0.006% error in discrepancy.

Annelisa B Esparza↗
NASA NTRSDate not supplied

The Porous Microstructure Analysis (PuMA) software

The open-source Porous Microstructure Analysis (PuMA) software was created to offer an efficient framework for determining material properties from 3D microstructures. Its development was inspired by progress in X-ray microtomography, an imaging technology that captures the internal structure of materials in 3D, and even in a 4D temporal context. Over recent years, this method has transformed the domain of materials science due to its capability to non-destructively examine material microstructures while presenting digital data about their geometrical details. It has provided insights into materials relevant to several NASA missions, including heatshields, parachute fabrics, meteorites, and other advanced composites. PuMA, in its current version 3, delivers an array of features, spanning from basic geometric insights of a microstructure to intricate anisotropic thermo-elastic and chemical behavior. Specifically, the software evaluates morphological attributes (specific surface area, volume fractions, mean intercept lengths, orientation) and physical characteristics (conductivity, elasticity, permeability, and tortuosity). Additionally, it can model material degradation processes, such as oxidation and surface chemistry interactions. The software can generate synthetic microstructures, from straightforward geometrical designs to intricate woven and non-woven geometries. Coupling material generation and characterization enables parametric studies and sensitivity analysis to optimize the microstructural performance and inform design decisions and reliability assessment based on uncertainty quantification. A recent addition to PuMA includes the TomoSAM plugin, devised to incorporate the cutting-edge Segment Anything Model (SAM) into our image segmentation workflow. SAM is a promptable deep learning model that can identify objects and create image masks in a zero-shot manner, based only on a few user clicks. The synergy between these tools aids in the segmentation of complex 3D datasets from tomography and other imaging techniques, which would otherwise require a laborious manual segmentation process.

Tomography↗