Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reactor experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Irradiation-induced swelling of pure chromium with 5 MeV Fe ions in the temperature range 450–650 °C

A surface coating using pure chromium has been proposed to increase the accident tolerance of Zircaloy cladding in pressurized water reactors. However, there is not much irradiation experience with Cr alloys and especially pure Cr. In the present study, pure chromium was irradiated with 5 MeV Fe ions to 50 peak dpa (displacements per atom) at temperatures of 450, 500, 550, 600 and 650 °C. Then irradiation at the peak swelling temperature of 550 °C was conducted to 50, 100, 150 peak dpa. Swelling at 50 dpa was observed over the entire temperature range studied, 450–650 °C, but appeared to be decreasing strongly at the temperature boundaries of the experiment. After an initial transient of rapid swelling, chromium was observed to swell at a rate of ~0.03–0.04%/dpa (up to 120 local dpa), which is much lower than pure Fe at 0.2%/dpa. This low swelling rate was found to be relatively insensitive to dpa rate, which varied by a factor of ~2 over the depth of data collection. Here, swelling was observed to begin quickly with an incubation period less than 10 dpa. Self-organization in the form of void ordering was observed to be developing at 50 dpa, becoming better defined with increasing dose. The void alignment direction is determined to be the $\langle$111$\rangle$ axial direction.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantitative Detection of Products and Radical Intermediates in Low-Temperature Oxidation of Cyclopentane

We present a combined experimental and theoretical investigation of the autoignition chemistry of a prototypical cyclic hydrocarbon, cyclopentane. Experiments using a high-pressure photolysis reactor coupled to time-resolved synchrotron VUV photoionization mass spectrometry directly probe the short-lived radical intermediates and products in cyclopentane oxidation reactions. We detect key peroxy radical intermediates ROO and OOQOOH, as well as several hydroperoxides, formed by second O 2 addition. Automated quantum chemical calculations map out the R + O 2 + O 2 reaction channels and demonstrate that the detected intermediates belong to the dominant radical chain-branching pathway: ROO (+ O 2 ) → γ-QOOH + O 2 → γ-OOQOOH → products. ROO, OOQOOH, and hydroperoxide products of second-O 2 addition undergo extensive dissociative ionization, making their experimental assignment challenging. We use photoionization dynamics calculations to aid in their characterization and report the absolute photoionization spectra of isomerically pure ROO and γ-OOQOOH. Here, a global statistical fit of the observed kinetics enables reliable quantification of the time-resolved concentrations of these elusive, yet critical species, paving the way for detailed comparisons with theoretical predictions from master-equation-based models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Predicted Heat Flux Performance of Actively Cooled Tungsten-Armored Graphitic Foam Monoblocks

Tungsten (W)–armored graphitic foam monoblocks were developed for applications requiring high-Z plasma-facing material in long-pulse fusion experiments and ultimately deuterium-tritium fusion reactors. The monoblocks are an integrated material system combining the advantages of a chemical vapor deposited (CVD) W coating with a high-conductivity graphitic foam. The W is a high-melting-point, high-Z material with low tritium retention. The graphitic foam coupled to a swirl tube serves as a high-thermal-conductivity heat sink that cannot melt, although it can sublime at much higher temperatures than copper melts. Together, they comprise a robust plasma-facing component (PFC) weighing roughly 5% of an all-W component or 17% of a traditional W-coated copper heat sink.A single-channel mock-up consisting of four graphitic foam monoblocks equipped with a water-cooled swirl tube was fabricated for eventual testing in the 60-kW, EB-60, rastered electron beam at the Applied Research Laboratory of The Pennsylvania State University. Two monoblocks have a thin 50-μm-thick coating of pure W chemically vapor deposited over NbC and pure Nb interlayers. Two others have a 2-mm-thick pure W coating CVD on graphitic monoblocks using the same interlayers. The mock-up will be cooled with available 10 m/s, 0.7 MPa water with a 22°C inlet temperature and subjected to varying uniform heat loads up to 20 MW/m 2 . It is equipped with type-K thermocouples at various depths, and calibrated infrared thermography and spot pyrometry will be used to characterize the heated surface. Real-time water calorimetry will be used to ascertain the absorbed steady-state power and infer the heat flux during testing. Since testing cannot be done under prototypic divertor flow conditions, it is necessary to predict the thermal response of this novel PFC system and investigate the power sharing between radiation and convection at divertor heat flux levels and its inherent ability to avoid critical heat flux. Results are reported for predictions obtained from computational fluid dynamics models up to 30 MW/m 2 of steady-state uniform heat flux. Leading-edge heat loads of 30 MW/m 2 on a 2-mm-wide side strip were also investigated to ascertain if coating delamination is likely.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Kinetics of Hydrogen Generation from In-Situ Methane Pyrolysis: Enhanced by Electromagnetic Heating and Natural Catalysts of Reservoir Rocks

Catalytic pyrolysis of methane (CH4) is a promising approach to generate hydrogen (H2). The apparent activation energy of this process has a significant influence on the efficiency and required temperature for H2 generation. Preliminary experiments indicate that minerals present in shales have catalytic effects during in-situ H2 generation from shale reservoirs under electromagnetic (EM) heating. However, the quantitative role of such natural catalysts on apparent activation energy is not explored yet. This research evaluated the role of reservoir rock (shale) in EM heating and on the apparent activation energy of methane pyrolysis (MP) for in-situ H2 generation. Experiments are conducted in a customized EM reactor with frequency 2.45 GHz, and reaction temperature and generated gases are measured by a real-time IR pyrometer and gas analyzer, respectively. It is found that shale samples experienced thermal runway (TR) at 420 ºC under 0.15 kW EM power without any artificial heating promoter. In the presence of spent shale, CH4 conversion started approximately at 600 ºC with negligible amount of carbon dioxide (CO2) generated during this process. We further calculated apparent reaction order and apparent activation energy for MP process in the presence of shale under EM heating, which are 0.4357 and 98.12 kJ/mol, respectively. This research paves a way for leveraging the role of minerals as natural catalysts for enhancing H2 generation under EM heating in petroleum reservoirs.

02 PETROLEUM↗
DOE OSTI2020

Terry Turbopump Expanded Operating Band Modeling and Simulation Efforts in Fiscal Year 2020 - Progress Report

The Terry Turbine Expanded Operating Band Project is currently conducting testing at Texas A&M University as part of a revised experimental program meant to supplant previous full-scale testing plans under the headings of Milestone 5 and Milestone 6. In consultation with Sandia National Laboratories technical staff and with modeling and simulation support from the same, the hybrid Milestone 5&6 plan is moving forward with experiments aimed at addressing knowledge gaps regarding scale, working fluid, and turbopump self-regulation. Modeling and simulation efforts at Sandia National Laboratories in FY20 fell under the broad umbrella of Milestone 7 and consisted exclusively of MELCOR-related tasks aimed at: 1) Constructing/improving input models of Texas A&M University experiments, 2) Constructing a generic boiling water reactor input model according to best practices with systems-level Teny turbine capabilities, and 3) Adding code capability in order to leverage experimental data/findings, address bugs, and improve general code robustness Project impacts of the Covid-19 pandemic have fortunately been minimal thus far but are mentioned as necessary when discussing the hybrid Milestone 5&6 progress as well as the corresponding Milestone 7 modeling and simulation progress.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Engineering Assessment of UO 2 and Cladding Behavior under High Burnup LOCA Conditions

To maximize the data extracted from a limited number of high-burnup fuel rod samples, several modeling efforts were performed to elucidate the fuel and the cladding responses of these fuels under transient conditions. These objectives were (1) to determine the role of the fuel stress state in fuel pulverization, (2) to ascertain the differences between conditions of cladding burst during experiments and those expected during a commercial reactor transient, and (3) to develop a method to conservatively calculate the geometry of the cladding rupture’s opening to inform fuel dispersal susceptibility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Quick Look Report of Godiva U233 shot March 2022 Data Collection Activities

This report discussing the March 2022 irradiation of U233 on the Godiva critical assembly using burst mode and subsequent analysis of the fission products starting at 65 minutes post irradiation, and ending 12 days later. The Short-Lived Fission Product Yield (SLFPY) project is one of many efforts under the Nuclear Physics Multi-Lab and related Venture Project. The objective of the SLFPY project is to provide improved measurements of fission product yields for select nuclides. The SLFPY project consists of measurement and analysis campaigns. To produce fission data, samples of actinide material are irradiated in a high-flux neutron environment. These samples are quickly placed in front of a detection system where both gamma singles and coincidence spectra are collected as a function of time. Gamma spectroscopy is performed on the irradiated material on site near the irradiation facility, starting as soon as feasible after the irradiation and continuing for 7 days or longer. Following the data collection, time-dependent fission yield analyses are performed using gamma-ray spectroscopy. This document summarizes the measurement campaign performed March 21 - April 4, 2022 where sub-gram quantities of 233 U nitrate (UO 2 (NO 3 ) 2 ) were irradiated in the Godiva reactor. The Godiva burst #2076 conducted under experiment IER 504 had a temperature change of +156 degrees Celsius, lasted 13.32 microseconds, and had a reactivity of $\$$1.089. The targets consisted of uranium oxide solution deposited in a quartz tube and packed with quartz wool. The flame-sealed quartz ampoules were used to contain the uranium samples for the irradiation and count activities. On March 22, 2022, at 10:27:00 a.m. the three uranium ampoules, along with a witness foil pack, were irradiated in the Godiva critical assembly using burst mode operations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

FY21 Progress Report for Advanced Re fabrication/Re-instrumentation Capability Development

In support of performing follow on irradiation experiments with previously irradiated materials, the Halden Reactor Project developed unique and state of the art capabilities to refabricate and re-instrument previously irradiated materials. Such materials were used in in-pile tests at the Halden reactor, and out-of-pile tests for example using furnaces as a heat source. The decision to close the Halden Reactor Project results in the loss of this refabrication and reinstrumentation capability. As a result, the United States Department of Energy has determined to develop refabrication and re-instrumentation capability at the unique shielded facilities at Idaho National Laboratory. The development of refabrication capability has been completed and demonstrated. This report focuses on the complementary aspects of re-instrumentation and the progress to date. Halden spent nearly 30 years developing both refabrication and reinstrumentation. Collaboration with Halden is allowing INL to develop this capability much more rapidly. The results include development of the capability to drill annular center holes in ceramic UO2 fuel pellets, development of fuel rod end caps with feedthroughs for centerline instrumentation inside the rodlet, The procurement of both fuel drilling and welding demonstration equipment from Halden, evaluation of surface thermocouple attachments to support better understanding of temperature measurement uncertainties, and finally, the conceptual design of a new shielded enclosure where advanced refabrication and re-instrumentation equipment can be housed. The authors would like to thank the numerous colleagues at INL and Halden who provided support in accomplishing this work. Their support both material and intellectual is invaluable in advancing the state of the art and establishing the capabilities for refabrication and re-instrumentation at INL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Material Test Reactors; Annular Core Research Reactor Testing

The Material Test Reactors Fifth Workshop reviews the successes and failures of material test protocols and lessons learned. This presentation introduces the Annular Core Research Reactor (ACRR), the history of nuclear reactors at Sandia National Labs and the experiment review process. Included are actual examples of experimental activities at ACRR.

Martin, Lonnie E. [Sandia National Laboratories (S↗
NASA NTRS1972

NASA-Lewis experiences with multigroup cross sections and shielding calculations

The nuclear reactor shield analysis procedures employed at NASA-Lewis are described. Emphasis is placed on the generation, use, and testing of multigroup cross section data. Although coupled neutron and gamma ray cross section sets are useful in two dimensional Sn transport calculations, much insight has been gained from examination of uncoupled calculations. These have led to experimental and analytic studies of areas deemed to be of first order importance to reactor shield calculations. A discussion is given of problems encountered in using multigroup cross sections in the resolved resonance energy range. The addition to ENDF files of calculated and/or measured neutron-energy-dependent capture gamma ray spectra for shielding calculations is questioned for the resonance region. Anomalies inherent in two dimensional Sn transport calculations which may overwhelm any cross section discrepancies are illustrated.

Lahti, G. P.↗
NASA NTRS1979

University of Illinois nuclear pumped laser program

The development of nuclear pumped lasers with improved efficiency, energy storage capability, and UF6 volume pumping is reviewed. Results of nuclear pumped laser experiments using a TRIGA-type pulsed reactor are outlined.

Miley, G. H.↗
DOE OSTI2022

Intrinsic Junction Thermocouples For Surface Temperature Measurement

The material selection, attachment, and calibration of intrinsic junction thermocouples is discussed. Intrinsic junction thermocouples are utilized for their fast response times in surface measurements during high thermal transients. The as-is measurement and calibrated corrections are presented for both the out-of-pile pulse power system and the critical heat flux experiments in the Idaho National Laboratory Transient Reactor Test facility. The fin effect from temperature measurements on the surface of fuel cladding is corrected using a linear coefficient, m, and temperature corrections are sometimes 100 °C or more—representing 18% of the original temperature measurement.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Pulse Radiolysis Study of Radiation Effect on Molten Salt

The molten salt reactor concept, where nuclear fuel is dissolved in a molten salt that also serves as the heat transfer fluid, is a leading candidate for next generation nuclear reactors. This necessitates a thorough understanding of radiation effects on molten salt media to support the design, development, and deployment of such reactors. Early, pioneering pulse radiolysis molten salt experiments observed key primary radiolysis products such as the solvated electron (esolv?) and dichloride radical anion (Cl2??), but left many fundamental mechanistic and reactivity questions unanswered. Here we report on the reaction kinetics of esolv? and Cl2?? in molten LiCl-KCl eutectic salt doped with Zn2+ ion, using electron pulse radiolysis to observe the transient behavior from nanosecond to microsecond time scales. Experiments were performed at the BNL Laser-Electron Accelerator Facility using a recently-developed high-temperature sample holder. Prompt formation of esolv? and Cl2?? are observed; esolv? decays within hundreds of nanoseconds while Cl2?? decays more slowly by second-order kinetics, more likely by cross-recombination rather than disproportionation. This work was supported as part of the Molten Salts in Extreme Environments Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗
DOE OSTI2026

Beyond $Δm^2$: Absolute Mass Sensitivity in Neutrino Oscillations

Conventional wisdom says that neutrino oscillations measure only mass-squared differences and not the absolute neutrino mass scale. This is true, however, only at leading order in the expansion parameters $m_i/E$, the ratios of the neutrino masses $m_i$ ($i=1,2,3$) to the neutrino energy $E$. At next-to-leading order, the oscillation phase includes terms proportional to $m_i^4-m_j^4 = Δm^2_{ij}(m_i^2+m_j^2)$, and is therefore sensitive to the absolute mass scale. In this paper, we derive the next-to-leading-order corrections using a wave-packet treatment and taking into account the neutrino-production kinematics. We then apply this result to reactor antineutrinos and find that the JUNO experiment is sensitive to neutrino masses of a few hundred keV. While not competitive with existing bounds from beta decay, electron capture, and cosmology, neutrino oscillations provide a novel, complementary probe of the neutrino mass scale, with sensitivity to a different combination of neutrino masses.

Alves, Gustavo F.S. [Fermilab; Argonne; Northweste↗
DOE OSTI2020

Foreword Special issue on the Kilopower Project, Kilowatt Reactor Using Stirling TechnologY (KRUSTY) Test

This special issue of Nuclear Technology contains full-length, peer-reviewed papers describing the design work leading up to and the results of the Kilowatt Reactor Using Stirling TechnologY (KRUSTY) test. KRUSTY was the centerpiece of the National Aeronautics and Space Administration (NASA) Kilopower Project to design, build, and test a space nuclear reactor. This test was the first such test since the end of the Space Nuclear Auxiliary Power (SNAP) project at the end of the 1960s. In this issue, the introduction paper presents the goals of the Kilopower Project and the potential missions this reactor concept could serve in NASA. Kilopower was intended to serve both human exploration needs on planetary surfaces as well as science needs for deep-space exploration. The design work for the experiment by Poston and the power conversion development by Gibson present the pre-work required to perform the eventual KRUSTY test. A paper on regulatory analysis follows, to show the path used to gain approval of the proposed experiment. Then, the early zero-power critical experiments are presented by Sanchez and Grove. These experiments were essential data used to enhance model predictions prior to the high-temperature test. Next, Poston presents the three experiments (warm criticals) that increase the temperature in an incremental fashion prior to the final experiment. These experiments were used to achieve final regulatory approval of the final high-temperature experiment. The last paper by Poston presents the results of the steady-state and transient testing of the reactor at full power and at the design temperature. These results show that the reactor design and as-built experiment met all of the requirements that NASA had developed for the system. Any experiment of this magnitude was accomplished only because of the hard work and dedication of a large number of people at multiple institutions, including the NASA Glenn Research Center, NASA Marshall Space Flight Center, Y-12 National Security Site, Los Alamos National Laboratory, and the Nevada National Security Site prime contractor (formerly National Security Technologies and now the Mission Support and Test Services). The project was jointly funded by the Space Technology Mission Directorate at NASA and the Criticality Safety Program at the National Nuclear Security Administration (NNSA). A special thanks to Jerry McKamy and Angela Chambers at the NNSA and Lee Mason and Don Palac at NASA for their support and guidance. For the authors and multitude of staff that performed this work, the passion for space nuclear reactors was the key to making this experiment a reality.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Preliminary MITR Design-Demonstration Element Thermal-Hydraulics and Structural Analyses

The United State High Performance Research Reactor (USHPRR) program aims to eliminate more than 200kg of High Enriched Uranium (HEU) from commerce annually by converting five U.S. high-performance research reactors and one associated critical assembly to Low Enriched Uranium (LEU) fuel using a high-density alloy of uranium-10 wt% molybdenum (U-10Mo). Massachusetts Institute of Technology Reactor (MITR) is one of five research reactors selected for this program. The objective of this report is to provide preliminary thermal-hydraulic and mechanical analyses of the hydrodynamic effects in the MITR Design Demonstration Element (DDE) under conservative approximations for the plate power distribution. This report provides details on the modeling approach and the simulation results obtained, including pressure, flow velocity, temperature, and oxide layer over the design demonstration experiment for the irradiation cycles in the Belgian Reactor (BR)-2.

42 ENGINEERING↗
DOE OSTI2023

Preliminary NBSR Design-Demonstration Element Thermal-Hydraulics and Structural Analyses

1.1 OBJECTIVE The United State High Performance Research Reactor (USHPRR) program aims to eliminate more than 200kg of High Enriched Uranium (HEU) from commerce annually by converting five U.S. high-performance research reactors and one associated critical assembly to Low Enriched Uranium (LEU) fuel using a high-density alloy of uranium-10 wt% molybdenum (U-10Mo). The National Bureau of Standards Reactor (NBSR) is one of five research reactors selected for this program. The objective of this report is to provide preliminary thermal-hydraulic and mechanical analyses of the hydrodynamic effects in the NBSR Design Demonstration Element (DDE) under conservative approximations for the plate power distribution. This report provides details on the modeling approach and the simulation results obtained, including pressure, flow velocity, temperature, and oxide layer over the design demonstration experiment for the irradiation cycles in the Belgian Reactor (BR)-2.

42 ENGINEERING↗