Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “powder diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Compositional screening of Ce-doped (Gd,Lu,Y) 3 (Al,Ga) 5 O 12 ceramics prepared by quenching from melt and their luminescence properties

Quenching from the melt using an Optical Floating Zone furnace was investigated as a possible high-throughput preparation method in order to screen novel scintillating materials. To validate this method, polycrystalline rare-earth aluminum garnets and yttrium gallium aluminum garnets were synthesized and characterized by X-ray diffraction, photoluminescence and radioluminescence emission spectra as well as radioluminescence imaging and compared to the previously reported properties of those materials. In order to achieve rapid, but quantitative comparison of the materials, pellets fabricated from the synthesized powders were sintered; two different sintering conditions were investigated and compared. Therefore, a simplistic energy deposition and light absorption model for brightness of opaque samples under X-ray irradiation was developed to estimate the relative scintillation efficiency of the materials. Based on the results, Y 3 Al 5 O 12 , LuY 2 Al 5 O 12 and GdY 2 Al 5 O 12 seem to have the highest scintillation efficiency among the prepared samples.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Neutron scattering study of tantalum monohydride and monodeuteride

Powder samples of TaH 0.89 and TaD0.96 are synthesized under a hydrogen (deuterium) pressure of 2.8 GPa and a temperature of 250 °C, then quenched to the liquid nitrogen temperature, recovered to ambient pressure and studied by neutron diffraction (ND) and inelastic neutron scattering (INS). The ND study shows that both hydrogen and deuterium atoms occupy tetrahedral interstitial sites in a distorted body centered cubic (bcc) crystal structure of metal atoms, while the ordering scenarios in TaH 0.89 and TaD 0.96 are different. Hydrogen and deuterium atoms are ordered in a layered fashion, forming long period superstructures with space groups P$\bar{4}$ and P222, respectively, so that the unit cells of the crystal structures of TaH 0.89 and TaD 0.96 are $\sqrt{2}$ × $\sqrt{2}$ × 7 and $\sqrt{2}$ × $\sqrt{2}$ × 8 supercells of the initial cubic unit cell. The INS study demonstrates a pronounced “soft” (trumpet-like) anharmonicity of the potential well for H and D atoms.

08 HYDROGEN↗
NASA NTRS1982

Effect of reduced cobalt contents on hot isostatically pressed powder metallurgy U-700 alloys

The effect of reducing the cobalt content of prealloyed powders of UDIMET 700 (U-700) alloys to 12.7, 8.6, 4.3, and 0% was examined. The powders were hot isostatically pressed into billets, which were given heat treatments appropriate for turbine disks, namely partial solutioning at temperatures below the gamma prime solvus and four step aging treatments. Chemical analyses, metallographic examinations, and X-ray diffraction measurements were performed on the materials. Minor effects on gamma prime content and on room temperature and 650 C tensile properties were observed. Creep rupture lives at 650 C reached a maximum at the 8.4% concentration, while at 760 C a maximum in life was reached at the 4.3% cobalt level. Minimum creep rates increased with decreasing cobalt content at both test temperatures. Extended exposures at 760 and 815 C resulted in decreased tensile strengths and rupture lives for all alloys. Evidence of sigma phase formation was also found.

Harf, F. H.↗
NASA NTRS1988

Field-induced orientation of nonlevitated microcrystals of superconducting YBa2Cu3O(7-x)

X-ray diffraction patterns of superconducting YBa2Cu3O(7-x) particles which have typical dimensions D of less than 5 microns and do not levitate in an inhomogeneous magnetic field at T less than Tc show marked evidence of particle alignment when powder specimens are subjected to a 0.5-T field at T less than Tc, but reveal random orientation for T greater than Tc. A majority of the particles align preferentially with their antiphase twin boundary planes and a-b planes along the applied field, but a minority align with their b axes along the field.

Solin, S. A.↗
NASA NTRS2017

Surveying Clay Mineral Diversity in the Murray Formation, Gale Crater, Mars

One of the primary science goals of Mars Science Laboratory (MSL) is to investigate layered clay mineral-bearing deposits outcropping in the lower NW slopes of Aeolis Mons (Mt. Sharp) detected from orbit. Martian clay mineral-bearing layered rocks are of particular interest because they are potential markers of sedimentary deposits formed in habitable aqueous environments. The CheMin X-ray diffraction (XRD) instrument aboard MSL has documented clay minerals in various drill samples during its traverse of Gale Crater's floor and ascent of Mt. Sharp. Previously, the high concentrations of clay minerals (approximately 20 wt.%) detected in drill powders of mudstone (Sheepbed member) at Yellowknife Bay (YKB) allowed their detailed characterization. Drill powders recovered from lacustrine mudstones of the Sheepbed member at YKB contain smectite clay minerals. Based on the position of 02l reflections in XRD patterns, which serve as an indicator of octahedral occupancy, the smectites are Fe-bearing, trioctahedral species analogous to ferrian saponites from terrestrial deposits. The smectites are thought to have been formed through a process of isochemical aqueous alteration of detrital olivine close to the time of sediment deposition under anoxic to poorly oxidizing conditions. The clay minerals are key indicators that the lake waters were benign and habitable at the time. Clay minerals were detected at other locations during MSL's traverse, including samples from the Pahrump Hills, but lower abundances and overlapping peaks from crystalline phases in XRD patterns hamper in-depth analysis.

Bristow, T. F.↗
DOE OSTI2024

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

316L stainless steel↗
DOE OSTI2022

Spall damage mechanisms in laser powder bed fabricated stainless steel 316L

This paper reports on spall damage mechanisms in laser powder bed fusion (LPBF) fabricated stainless steel 316L (SS316L) subjected to uniaxial, strain plate-impact loading and explores failure evolution with increasing impact velocity and peak pressure. Analysis of velocimetry profiles reveals a heterogeneous failure response with several different failure mechanisms activated during impact and resulting spall. The analysis is supported by optical microscopy and electron backscattered diffraction (EBSD) observation of soft recovered impacted samples, which show evidence of localized nano-twinning, twin growth, severe grain rotation, and grain refinement along the spall plane, in addition to pore nucleation, coalescence, and growth. Furthermore, the observed failure mechanisms, including crack formation and propagation along high angle grain boundaries (HAGBs), are not consistently indicative of ductile fracture typical of wrought stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stirring and peristaltic pumping alter flow electrode particle size and morphology

Flowable carbon-based electrodes are widely studied in electrochemical systems for energy storage and water treatment. Most laboratory- and pilot-scale studies employ active mixing for slurry preparation and handling and use peristaltic pumps for slurry circulation. Magnetic stirring is the most prevalent mixing method at the laboratory scale, and the combination of magnetic mixing and peristaltic pumping is favored for convenience and compatibility with particulate suspensions. However, these methods can strongly affect particle size and morphology (and therefore cell performance). In this study, we evaluate how mixing and pumping influence particle degradation in two commonly used carbon materials: spherical carbon black (CB) beads and powdered activated carbon (AC). We performed 24 h stirring-only experiments using magnetic, orbital, and overhead stirring. Separately, we conducted 32 h circulation experiments using a commercial peristaltic pump. Particle morphology and size were analyzed using optical microscopy and laser diffraction. The initially spherical CB beads (~580 μm, 1.5 wt%) exhibit rapid and extensive breakdown under both peristaltic pumping and magnetic stirring. By comparison, AC particles (initially ~31 μm) tested at 1.5 and 15 wt% showed measurable size reductions of up to ~25 % under either stirring or pumping. In conclusion, these findings highlight the need to account for and quantify morphological changes caused by both stirring and pumping in the design and associated evaluation of flowable electrode systems.

Chemistry↗
DOE OSTI2022

Interplay of strain and phase evolution of laser powder bed fusion Ti–6Al–4V

While additive manufacturing (AM) provides a method of producing geometrically complex and highly detailed structures, the generation of residual strain in AM processes like laser powder bed fusion (L-PBF) can negatively impact performance-enabling properties. In applications such as orthopedic implants, specific performance windows require optimized microstructures in order to obtain desirable properties from multi-phase alloys like Ti–6Al–4V. This research aims to quantify the microscale origins of strain in L-PBF manufactured Ti–6Al–4V by understanding how strain is distributed at the grain and sub-grain scale, the interplay between phase evolution and strain, and examining post-processing strain relief strategies to control these features. Model spinal cage implants were manufactured from Ti–6Al–4V powder via L-PBF and then subjected to strain relieving heat treatment cycles above and below the Ti–6Al–4V β transus as a function of time and cooling rate. Residual strain was then studied via high resolution electron backscatter diffraction (HR-EBSD), and 2D strain maps with sub-micron resolution were generated for each post-processing state. It was found that macroscale thermal strains decreased with heat treatment time, but additional contributions from phase stabilizing residual strains retained primarily in the α' grains as lattice distortive strain remained. Additionally, the retention of β phase significantly changed the strain and dislocation distribution while reducing overall residual strain. In conclusion, these results were validated and reinforced with 3D mesoscopic micromechanical modeling of strain behavior across simulated microstructures, confirming that the local lattice dilation of α’ martensite is a primary contributor of microscale strain generation and retention in L-PBF Ti–6Al–4V.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Synthesis of Lanthanide-Based Intermetallic Silicides

Lanthanide-containing materials are of interest because of their useful magnetic and electronic behavior. To study this intrinsic behavior, researchers need high-quality single crystals to avoid interference from grain boundaries or defects commonly found in polycrystalline samples. One method for growing single crystals is metal-flux synthesis, an approach that promotes crystal growth at lower reaction temperatures thus providing access to complex intermetallic phases. My project focuses on synthesizing novel lanthanide-containing intermetallic silicides related to previously reported f-element compounds with the Gd1??Fe4Si10?? structure type. I investigated reactions targeting lanthanum, praseodymium, neodymium, samarium, europium, and gadolinium-containing products, and used scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) to identify promising lanthanide-containing phases. I prepared reactions by loading lanthanide oxides, Co, Si, Al, and Ga into alumina crucibles in a 0.2:1:1:10:10 Ln2O3/Co/Si/Al/Ga mmol ratio, where Ln = La, Nd, Pr, Sm, Eu, or Gd. The reactions were sealed in quartz tubes, heated in a furnace, and centrifuged to separate crystals from excess flux. Afterwards, I mechanically isolated single crystals and prepared them for characterization. Pr-, Nd-, and Sm-containing reactions were confirmed through SEM-EDS to have formed the targeted quaternary phase. Single crystal X-ray diffraction (SC-XRD) data showed the Nd-containing crystals exhibited a hexagonal unit cell associated with the Gd1??Fe4Si10?? structure type. La- and Eu-containing reactions instead formed competing Co(Al/Ga/Si)3 phase crystals. Single-crystal XRD, powder XRD, and magnetic susceptibility and heat-capacity measurements will be collected for the remaining lanthanide-containing crystals. This data will help determine the complete crystal structure of the lanthanide analogues, their phase purity and whether they exhibit localized magnetic behavior, magnetic ordering, or other electronic signatures that can be compared with the previously reported actinide analogues. The disordered structure of this intermetallic family is associated with unusual magnetic and electronic behavior meaning lanthanide analogues may show potential as thermoelectric materials. Developing new thermoelectric candidate materials is relevant to energy efficiency and waste-heat recovery, which supports DOE’s broader goal of advancing science and technology solutions for America’s energy needs.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
NASA NTRS1979

X-ray diffraction studies of shocked lunar analogs

The X-ray diffraction experiments on shocked rock and mineral analogs of particular significance to lunar geology are described. Materials naturally shocked by meteorite impact, nuclear-shocked, or artificially shocked in a flat plate accelerator were utilized. Four areas were outlined for investigation: powder diffractometer studies of shocked single crystal silicate minerals (quartz, orthoclase, oligoclase, pyroxene), powder diffractometer studies of shocked polycrystalline monomineralic samples (dunite), Debye-Scherrer studies of single grains of shocked granodiorite, and powder diffractometer studies of shocked whole rock samples. Quantitative interpretation of peak shock pressures experienced by materials found in lunar or terrestrial impact structures is presented.

Hanss, R. E.↗
NASA NTRS2006

Powder Handling Device for Analytical Instruments

Method and system for causing a powder sample in a sample holder to undergo at least one of three motions (vibration, rotation and translation) at a selected motion frequency in order to present several views of an individual grain of the sample. One or more measurements of diffraction, fluorescence, spectroscopic interaction, transmission, absorption and/or reflection can be made on the sample, using light in a selected wavelength region.

Sarrazin, Philippe C.↗
DOE OSTI2023

XFEL Microcrystallography of Self-Assembling Silver n -Alkanethiolates

New synthetic hybrid materials and their increasing complexity have placed growing demands on crystal growth for single-crystal X-ray diffraction analysis. Unfortunately, not all chemical systems are conducive to the isolation of single crystals for traditional characterization. Here, small-molecule serial femtosecond crystallography (smSFX) at atomic resolution (0.833 Å) is employed to characterize microcrystalline silver n-alkanethiolates with various alkyl chain lengths at X-ray free electron laser facilities, resolving long-standing controversies regarding the atomic connectivity and odd–even effects of layer stacking. smSFX provides high-quality crystal structures directly from the powder of the true unknowns, a capability that is particularly useful for systems having notoriously small or defective crystals. We present crystal structures of silver n-butanethiolate (C4), silver n-hexanethiolate (C6), and silver n-nonanethiolate (C9). We show that an odd–even effect originates from the orientation of the terminal methyl group and its role in packing efficiency. We also propose a secondary odd–even effect involving multiple mosaic blocks in the crystals containing even-numbered chains, identified by selected-area electron diffraction measurements. Finally, we conclude with a discussion of the merits of the synthetic preparation for the preparation of microdiffraction specimens and compare the long-range order in these crystals to that of self-assembled monolayers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2012

Effects of Kapton Sample Cell Windows on the Detection Limit of Smectite: Implications for CheMin on the Mars Science Laboratory Mission

The CheMin instrument on the Mars Science Laboratory (MSL) rover Curiosity is an X-ray diffraction (XRD) and X-ray fluorescence (XRF) instrument capable of providing the mineralogical and chemical compositions of rocks and soils on the surface of Mars. CheMin uses a microfocus X-ray tube with a Co target, transmission geometry, and an energy-discriminating X-ray sensitive CCD to produce simultaneous 2-D XRD patterns and energy-dispersive X-ray histograms from powdered samples. CheMin has two different window materials used for sample cells -- Mylar and Kapton. Instrument details are provided elsewhere. Fe/Mg-smectite (e.g., nontronite) has been identified in Gale Crater, the MSL future landing site, by CRISM spectra. While large quantities of phyllosilicate minerals will be easily detected by CheMin, it is important to establish detection limits of such phases to understand capabilities and limitations of the instrument. A previous study indicated that the (001) peak of smectite at 15 Ang was detectable in a mixture of 1 wt.% smectite with olivine when Mylar is the window material for the sample cell. Complications arise when Kapton is the window material because Kapton itself also has a diffraction peak near 15 Ang (6.8 deg 2 Theta). This study presents results of mineral mixtures of smectite and olivine to determine smectite detection limits for Kapton sample cells. Because the intensity and position of the smectite (001) peak depends on the hydration state, we also analyzed mixtures with "hydrated" and "dehydrated"h smectite to examine the effects of hydration state on detection limits.

Achilles, C. N.↗
DOE OSTI2026

Shock-induced phase transitions and stacking fault formation in additively manufactured eutectic high-entropy alloy Ni 40 Co 20 Fe 10 Cr 10 Al 18 W 2

Ni 40 Co 20 Fe 10 Cr 10 Al 18 W 2 additively manufactured using laser powder bed fusion (LPBF) is among the toughest as-built alloys reported and is a promising candidate for use in extreme environments. However, its behavior under multi-megabar pressure regimes remains unexplored. We used femtosecond in situ X-ray diffraction to investigate the shock response of LPBF Ni40Co20Fe10Cr10Al18W2 under laser-driven shock compression and release. Our results reveal that the initial dual-phase face-centered + body-centered structure transforms to a single face-centered phase over a wide pressure range of 84±10 to 277±55 GPa, followed by a transition to a single body-centered phase at 431±48 GPa. We establish the Hugoniot equation-of-state of LPBF Ni 40 Co 20 Fe 10 Cr 10 Al 18 W 2 and compare it to the benchmark alloy AlCoCrFeNi 2.1 , demonstrating the effects of W-doping and increased Al content. High stacking fault probabilities, close to those measured in Au and Ag, are observed upon compression. A portion of the stacking faults are annihilated upon release to ambient pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

FeSi 4 P 4 and CoSi 3 P 3 : Hidden Gems of Ternary Tetrel Pnictides with Outstanding Nonlinear Optical Properties

Metal silicon phosphides have shown promise as nonlinear optical materials. To be practically useful and cheap, earth-abundant 3d transition metals are preferred over their scarcer and more expensive 4d and 5d counterparts. Here, we developed a synthetic method to produce polycrystalline bulk powders and millimeter-sized single crystals of ternary compounds FeSi 4 P 4 and CoSi 3 P 3 . Both studied compounds have noncentrosymmetric and chiral crystal structures with ordered Si/P arrangements as was confirmed by single-crystal X-ray diffraction and solid-state NMR. Despite the presence of the transition metal, FeSi 4 P 4 and CoSi 3 P 3 are semiconductors with direct band gaps of 1.3 and 1.6 eV, respectively, indicating low-spin d 6 electronic configuration for octahedral Fe 2+ and Co 3+ . Relative to reported sulfide materials, FeSi 4 P 4 and CoSi 3 P 3 small band gap semiconductors demonstrate an outstanding combination of second-harmonic generation (SHG) activity and laser damage threshold (LDT). Both studied materials are phase-matchable with a 2.09 μm laser and not only exhibit 2.5–3.0 times stronger SHG signal than that of the state-of-the-art AgGaS 2 standard but also demonstrate an LDT response of 2.3–2.5 times higher than that of AgGaS 2 (at 1.09 μm laser with a pulse width of 10 ns)-which is unprecedented for small band gap semiconductors.

36 MATERIALS SCIENCE↗
NASA NTRS1996

Synthesis, Structure, and Characterization of Cu4S10(4-methylpyridine)4

The title compound, Cu4S10(4-methylpyridine)(sub 4) (dot) 4-methylpyridine was prepared by three different reactions: the oxidation of copper powder by sulfur and the reaction of copper (I) sulfide (or CuBr (dot) SMe2) with excess sulfur, both in the coordinating solvent, 4-methylpyridine. Red crystals of the compound obtained by layering with hexanes were subjected to single crystal X-ray diffraction. The structure was refined to R = 0.026 and R(sub w) = 0.036 in a space group P1bar (No. 2), with Z = 2, a = 13.983 (2) A, b = 15.384 (2) A, c = 9.660 (1) A, alpha = 93.87 (1)deg., beta = 93.38 (1)deg., gamma = 99.78 (1)deg., V = 2037.9 (9) A(exp 3). The compound has approximate S(sub 4) symmetry and consists of two pentasulfide chains linking four Cu(I) ions, each with a corrdinating 2-methylpyridine. The infrared spectrum was dominated by absorption due to coordinated 4-methylpyridine with several low-energy peaks attributable to S-S stretches, which were also observed by Raman spectroscopy. A featureless electronic absorption spectrum yielded a single peak in the near ultraviolet upon computer enhancement (lambda = 334 nm, epsilon = 10,000), most likely an intraligand transition. Cyclic voltammetry indicates that the polysulfide complex undergoes irrversible oxidation and reduction at +0.04 and -0.34 V vs. SCE, respectively, at 298 K in 4-methylpyridine when swept at 20 mV/sec. The electrochemical behavior was unvaried even at sweep rates as high as 100 V/sec.

Hepp, Aloysius F.↗