Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Reliability of Materials and Components for Solid Oxide Fuel Cells

Planar stack solid-oxide fuel cells (SOFCs) require seals that must operate reliably under demanding conditions for lifetimes of 40000 hours. This includes temperature fluctuations between 800°C and RT during on and off cycles, thermal stresses, oxidizing environments and chemical degradation to name a few. This comprehensive report provides results from long term testing of two commercially available multicomponent barium alkali silicate glasses: SCN and G6, chosen as sealing candidates. In this scope, the glass seals were deposited on YSZ and Al 2 O 3 substrates simulating electrolytes (Zrbased) and coatings (both zirconia and Al 2 O 3 ). The seal-substrate couples were subjected to 800°C under air and steam+H 2 +N 2 environments up to 40000 hours to test their integrity under real operating conditions. Extensive studies on the effects of exposure have been conducted over the span of testing at various time intervals. Within the context of characterization, mechanical properties such as density, roughness, thermal expansion and glass transition, viscosity and wettability behavior; and microstructural properties such as glass chemistries, defect formation (cracks and pores), phase transformations (devitrification) and glass-interface reactions are investigated. Results and discussions are provided with a focus on the degradation of the properties over long term interrupted testing.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Microstructural Effects of High Dose Helium Implantation in ErD 2

Metal hydrides can store hydrogen isotopes with high volumetric density. In metal tritides, tritium beta decay can result in accumulation of helium within the solid, in some cases exceeding 10 at.% helium after only 4 years of aging. Helium is insoluble in most materials, but often does not readily escape, and instead coalesces to form nanoscale bubbles when helium concentrations are near 1 at.%. Blistering or spallation often occurs at higher concentrations. Radioactive particles shed during this process present a potential safety hazard. This study investigates the effects of high helium concentrations on erbium deuteride (ErD 2 ), a non-radioactive surrogate material for erbium tritide (ErT 2 ). To simulate tritium decay in the surrogate, high doses of 120 keV helium ions were implanted into ErD 2 films at room temperature. Scanning and transmission electron microscopy indicated spherical helium bubble formation at a critical concentration of 1.5 at.% and bubble linkage leading to nanoscale crack formation at a concentration of 7.5 at.%. Additionally, crack propagation occurred through the nanocrack region, resulting in spallation extending from the implantation peak to the surface. Electron energy loss spectroscopy was utilized to confirm the presence of high-pressure helium in the nanocracks, suggesting that helium gas plays a predominant role in deformation. This work improves the overall understanding of helium behavior in ErD 2 by using modern characterization techniques to determine: the critical helium concentration required for bubble formation, the material failure mechanism at high concentration, and the nanoscale mechanisms responsible for material failure in helium implanted ErD 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Adoption of image-driven machine learning for microstructure characterization and materials design: A Perspective

Microstructure characterization enables the development of structure-processing-property relationships critical to several research areas within the broad field of materials science, from alloy design to the assessment of corrosion resistance, and failure analysis. Conventional approaches to material characterization have relied on either qualitative inference by the human ex-pert or software applications that can extract high-level features from images, such as boundary segmentation, average grain diameter, etc. Such approaches rely heavily on subject matter expert user intervention and knowledge of what phases or more generally, what microstructural features, are of interest. The recent surge in the adoption of machine learning techniques to address problems in materials engineering has brought with it an increased interest and application of Image Driven Machine Learning (IDML) approaches. In this work, we review the applications of IDML to the field of materials characterization. A canonical hierarchy of stages is defined, which when put sequentially together completes an IDML study: problem definition, dataset building, model selection and training, model evaluation, and integration with existing instrumentation or simulation workflow. The studies reviewed in this work are analyzed from the perspective of each of these stages. Such a review permits agranular assessment of the field, for example the impact of IDML on materials characterization at the nanoscale, the size of a typical dataset required to train a semantic segmentation model on electron microscopy images, ubiquitousness of transfer learning in the domain, etc. Finally, we discuss the importance of interpretability and explainability in the field of IDML for materials characterization, and provide an overview of two emerging techniques in the field: semantic segmentation and generative adversarial networks.

Baskaran, Arun↗
DOE OSTI2023

Bridging microscale to macroscale mechanical property measurements of FeCrAl alloys by crystal plasticity modeling

FeCrAl alloys are candidates for accident tolerant fuel cladding of light water reactors. In this work, a microstructure- and temperature-dependent crystal plasticity model is employed to bridge microscale to macroscale mechanical property measurements of FeCrAl alloys. With the visco-plastic self-consistent (VPSC) polycrystal plasticity framework, a mechanism-based single crystal plasticity (MSCP) model adopts the Arrhenius type rate equation to describe the dependence of the critical resolved shear stress for dislocation slips on their temperature-dependent intrinsic frictional resistance and the microstructure-dependent irradiation hardening. The intrinsic frictional resistance associated with {110}<111> and {112}<111> slip systems were measured by in-situ micromechanical testing on unirradiated/irradiated samples at 25-500 °C. The irradiation hardening is estimated by the Bacon-Kocks-Scattergood (BKS) model with density and size of radiation-induced defects measured from microstructural characterization. Several features associated with thermo-mechanical behavior of unirradiated/irradiated polycrystalline FeCrAl alloys are captured. High density of deformation-induced dislocations and radiation-induced defects results in obvious hardening at room temperature, which is weakened at high temperature, and facilitates damage evolution during deformation. Moreover, both high temperature and radiation-induced defects, which facilitate dislocation multiplication, trigger large hardening rate. Finally, the proposed method together with application of accelerator-based ion irradiation technique is a surrogate approach to simulate neutron damage, improving the efficiency associated with evaluation of mechanical properties of FeCrAl alloys exposed to temperature, stress and radiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ab initio study of the structure and properties of amorphous silicon hydride from accelerated molecular dynamics simulations

This paper presents a large-scale ab initio simulation study of amorphous silicon hydride (a-Si 1-x H x ) with an emphasis on the structure and properties of the material across a range of hydrogen concentration by combining accelerated molecular dynamics (MD) simulations with first-principles density-functional calculations. The accelerated MD scheme relied on classical metadynamics, which enabled the development of 2600+ high-quality structural models of a-Si 1-x H x , with system sizes ranging from 150 to 6,000 atoms and hydrogen concentrations vary from 6 to 20 at. %. The resulting amorphous networks were found to be completely free from any coordination defects and that they all exhibited a pristine band-gap in their electronic spectrum. The microstructural properties of hydrogen distributions were examined with great emphasis on the presence of isolated and clustered environments of hydrogen atoms. The results were compared with a suite of experimental data obtained from x-ray diffraction, infrared spectroscopy, spectroscopic ellipsometry and nuclear magnetic resonance studies.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Exploiting the Temperature/Concentration Dependence of Magnetic Susceptibility to Control Convection in Fundamental Studies of Solidification Phenomena

The objective of this new research project is to demonstrate by experiment, supplemented by mathematical modeling and physical property measurement, that the effects of buoyancy driven convection can be largely eliminated in ground-based experiments, and further reduced in flight, by applying a new technique. That technique exploits the dependence of magnetic susceptibility on composition or temperature. It is emphasized at the outset that the phenomenon to be exploited is fundamentally and practically different from the magnetic damping of convection in conducting liquids that has been the subject of much prior research. The concept suggesting this research is that all materials, even non-conductors, when placed in a magnetic field gradient, experience a force. Of particular interest here are paramagnetic and diamagnetic materials, classes which embrace the "model alloys", such as succinonitrile-acetone, that have been used by others investigating the fundamentals of solidification. Such alloys will exhibit a dependence of susceptibility on composition. The consequence is that, with a properly oriented field (gradient) a force will arise that can be made to be equal to, but opposite, the buoyancy force arising from concentration (or temperature) gradients. In this way convection can be stilled. The role of convection in determining the microstructure, and thereby properties, of materials is well known. Elimination of that convection has both scientific and technological consequences. Our knowledge of diffusive phenomena in solidification, phenomena normally hidden by the dominance of convection, is enhanced if we can study solidification of quiescent liquids. Furthermore, the microstructure, microchemistry and properties of materials (thereby practical value) are affected by the convection occurring during their solidification. Hitherto the method of choice for elimination of convection has been experimentation in microgravity. However, even in low Earth orbit, residual convection has effects. That residual convection arises from acceleration (drag on the spacecraft), displacement from the center of mass or transients in the gravitational field (g-jitter). There is therefore a need for both further reducing buoyancy driven flow in flight and allowing the simulation of microgravity during ground based experiments. Previous investigations, the research project description, theory behind the study and experimental methods as well as plots of magnetic fields and forces are presented.

Evans, J. W.↗
NASA NTRS1999

Numerical Modeling and In-Situ Observations of the Dynamics of the Solid/Liquid Interface Morphology During Directional Solidification of Alloys

The departure from interface planarity and the subsequent evolution to a periodic array of cells or dendrites is a fundamental process that characterizes most microstructures in solidified alloys. The growing demand for high quality alloys and semiconductor crystals requires a precise methodology to predict and subsequently control both the interface morphology and the distribution of impurities, additives, and phases in the grown crystal. Apart from its practical significance, the study of morphological evolution has also been viewed as a means to unearth a general paradigm for pattern formation in nature. A previously developed 2D numerical model for the solid/liquid interface tracking has been further refined and used to simulate the time-evolution of the perturbations on the interface. The dynamics of the local growth velocity, interface undercooling and solute concentration at the interface has been theoretically predicted by means of the numerical model for Al-Cu and Pb-Sn alloys. The model shows that perturbations with a wavelengths, lambda greater than a critical wavelength lambda(sub c) continue to grow in time whereas perturbations with lambda < lambda(sub c) cease to propagate. The model further predicts that under certain conditions perturbation can also propagate along the interface. Comparison of these predictions with existing theories of pattern formation and experimental results will be discussed.

Catalina, Adrian V.↗
NASA NTRS2014

Coupling Damage-Sensing Particles to the Digitial Twin Concept

The research presented herein is a first step toward integrating two emerging structural health management paradigms: digital twin and sensory materials. Digital twin is an emerging life management and certification paradigm whereby models and simulations consist of as-built vehicle state, as-experienced loads and environments, and other vehicle-specific history to enable high-fidelity modeling of individual aerospace vehicles throughout their service lives. The digital twin concept spans many disciplines, and an extensive study on the full domain is out of the scope of this study. Therefore, as it pertains to the digital twin, this research focused on one major concept: modeling specifically the as-manufactured geometry of a component and its microstructure (to the degree possible). The second aspect of this research was to develop the concept of sensory materials such that they can be employed within the digital twin framework. Sensory materials are shape-memory alloys that undergo an audible phase transformation while experiencing sufficient strain. Upon embedding sensory materials with a structural alloy, this audible transformation helps improve the reliability of crack detection especially at the early stages of crack growth. By combining these two early-stage technologies, an automated approach to evidence-based inspection and maintenance of aerospace vehicles is sought.

Hochhalter, Jacob↗
DOE OSTI2022

Multi-Pass Hybrid Laser Arc Welding of Alloy 740H

The presentation reviews the progress made toward reducing the joining time of an advanced nickel-based alloy, Alloy 740H by a factor of two using a novel two step fusion welding approach. In the first step, a high powered laser is used to rapidly join thick weld groove lands (~10-12 mm thick) during a single pass. Hybrid laser arc welding (HLAW) is then used to fill the remaining weld groove and complete the joint. This sequential process also utilizes laser wobble in both steps to reduce welding defects and refine the weld microstructure to obtain improved properties compared to conventional gas tungsten or gas metal arc welds, GTAW and GMAW, respectively. The creep behavior of laser-only thick weld groove land welds and HLAW welds were found to be the same or slightly improved compared to conventional GMAW or GTAW welds in this alloy. Creep tests have been started to verify the long-term creep behavior (~10,000 hrs) of these welds. Modeling results on deep penetration laser welding are presented and the initial simulations of laser welding with laser wobble are shown. The next phase of the project will combine the two processes to make complete welds - deep penetration laser welds of thick weld groove lands followed by rapid filling of the remaining weld groove by HLAW - in thick plates (32 mm thick) Alloy 740H plate and entails development of narrow weld groove welding to further decrease the joining time of this alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Deep operator network surrogate for phase-field modeling of metal grain growth during solidification

A deep operator network (DeepONet) has been constructed that generates accurate representations of phase-field model simulations for evolving two dimensional metal grain morphology growing from melt. These representations serve as lower resolution, computationally efficient stand-ins for quick parameter space exploration of solutions to the the Allen-Cahn equations that dictate the phase-field model simulations. The experimental target for the phase-field model is a uranium casting system cooling a 434 g uranium charge from a maximum temperature of 1400° C at an average rate of 30° C / min , traversing the crystallographic phases of the pure metal. Experimental parameters inform the phase-field model, whose higher resolution computational model solutions are used to train the DeepONet in a given parameter space with the aim of developing a faster, more efficient method for predicting the solidifying metal's microstructure at different potential experimental values. The final DeepONet generates high accuracy, lower resolution predictions with cumulative relative approximation error over all timesteps of less than 0.5%, while ensuring solutions remain within physically feasible ranges. Further, these relative error values are comparable with other state-of-the-art DeepONet models for microstructure evolution, while significantly reducing the amount of training data required. Training a convolutional neural network simultaneously with the DeepONet, enforcing realistic values at the complex metal grain boundaries, and mathematically encoding boundary conditions into the structure of the DeepONet improved prediction accuracy and computational efficiency over a standard DeepONet model.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Flux Helium Irradiation of Dispersion-Strengthened Tungsten Alloys and Effects of Heavy Metal Impurity Layer Deposition

Tungsten has been chosen as the plasma-facing material (PFM) for the divertor region in ITER and also a candidate PFM for future plasma-burning nuclear fusion reactors. During fusion device operation, PFMs will be exposed to low-energy He irradiation at high temperatures, resulting in sub-surface bubbles and surface morphology changes such as pores and fuzz. Carbide dispersion-strengthened W materials may enhance the ductility of W, but their behavior under high flux He irradiation remains unclear. In this work, the response of dispersion-strengthened tungsten materials to high flux, low energy He irradiation at high temperature is examined. Tungsten alloyed with 1, 5, or 10 wt. % tantalum carbide or titanium carbide exposed to these conditions result in surface pores, coral-like feature growth and sub-surface helium bubbles. Reactor-relevant helium irradiation (5 x 10 26 m -2 fluence) combined with high powered laser pulses to simulate off-normal reactor events does not significantly alter the surface morphology, as the surface nanostructures appear stable and cracks are only observed on a localized region of one sample. However, specimens show the development of an impurity layer on the surface, likely impurity deposition from the sample holder during irradiation, resulting in a mixed material layer on the surface. Helium bubbles exist in this impurity layer, and obscure conclusions about helium interactions with the carbide dispersoids. Nonetheless, it is clear that the dispersoid microstructure limits He bubble formation and subsequent surface nanostructuring, attributed to the dispersoid composition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Kinetic Monte Carlo simulations of structural evolution during anneal of additively manufactured materials

Our experiments indicated that upon a post-processing anneal, an additively manufactured 316L stainless steel exhibits cubic grains rather than the conventional equiaxed grains. In this work, we have used kinetic Monte Carlo simulations to explore the origin of these cubic grains. First, we implemented a new kinetic Monte Carlo model in parallel code SPPARKS to simulate grain growth and recrystallization under a residual energy distribution. Our model incorporates physical properties and real-time, as opposed to generic properties and relative time. We further validated that our SPPARKS simulations reproduced the expected kinetic behavior of single-grain evolution. We then used the validated approach to simulate the anneal of an additively manufactured material under the same conditions used in our experiments. We found that the cubic grains can origin from a periodically varying residual energy that may be present in additively manufactured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High Radiation Resistance in the Binary W‐Ta System Through Small V Additions: A New Paradigm for Nuclear Fusion Materials

Abstract Refractory High‐Entropy Alloys (RHEAs) are promising candidates for structural materials in nuclear fusion reactors, where W‐based alloys are currently leading. Fusion materials must withstand extreme conditions, including i) severe radiation damage from energetic neutrons, ii) embrittlement due to H and He ion implantation, and iii) exposure to high temperatures and thermal gradients. Recent RHEAs, such as WTaCrV and WTaCrVHf, have shown superior radiation tolerance and microstructural stability compared to pure W, but their multi‐element compositions complicate bulk fabrication and limit practical use. In this study, it is demonstrated that reducing alloying elements in RHEAs is feasible without compromising radiation tolerance. Herein, two Highly Concentrated Refractory Alloys (HCRAs) − W 53 Ta 44 V 3 and W 53 Ta 42 V 5 (at.%) − were synthesized and investigated. We found that small V additions significantly influence the radiation response of the binary W–Ta system. Experimental results, supported by ab‐initio Monte Carlo simulations and machine‐learning‐driven molecular dynamics, reveal that minor variations in V content enhance Ta–V chemical short‐range order (CSRO), improving radiation resistance in the W 53 Ta 42 V 5 HCRA. By focusing on reducing chemical complexity and the number of alloying elements, the conventional high‐entropy alloy paradigm is challenged, suggesting a new approach to designing simplified multi‐component alloys with refractory properties for thermonuclear fusion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Visualization and validation of twin nucleation and early-stage growth in magnesium

The abrupt occurrence of twinning when Mg is deformed leads to a highly anisotropic response, making it too unreliable for structural use and too unpredictable for observation. Here, we describe an in-situ transmission electron microscopy experiment on Mg crystals with strategically designed geometries for visualization of a long-proposed but unverified twinning mechanism. Combining with atomistic simulations and topological analysis, we conclude that twin nucleation occurs through a pure-shuffle mechanism that requires prismatic-basal transformations. Also, we verified a crystal geometry dependent twin growth mechanism, that is the early-stage growth associated with instability of plasticity flow, which can be dominated either by slower movement of prismatic-basal boundary steps, or by faster glide-shuffle along the twinning plane. The fundamental understanding of twinning provides a pathway to understand deformation from a scientific standpoint and the microstructure design principles to engineer metals with enhanced behavior from a technological standpoint.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Arc Jet Testing of Hafnium Diboride Based Ultra High Temperature Ceramics

Hafnium Diboride (HFB,) based materials have shown promise for use in a number of high temperature aerospace applications, including rocket nozzles and as leading edges on hypersonic reentry vehicles. The stability of the materials in relevant environments is key to determining their suitability for a particular application. In this program we have been developing HfB2/SiC materials for use as sharp leading edges. The program as a whole included processing and characterization of the HfBJSiC materials. The specific work discussed here will focus on studies of the materials oxidation behavior in simulated reentry environments through arc jet testing. Four flat face models were tested to examine the influence of heat flux and stagnation pressure on the materials oxidation behavior. The results from arc jet testing of two HfB2/SiC cone models will also be discussed. Each cone model was run multiple times with gradually increasing heat fluxes. Total run times on a single cone model exceeded 80 minutes. For both the flat face and cone models surface temperatures well in excess of 2200 C were measured. Post test microstructural examination of the models and correlations with measured temperatures will be discussed.

Ellerby, Don↗
NASA NTRS2010

Microscopic Scale Simulation of the Ablation of Fibrous Materials

This slide presentation reviews the ablation by oxidation of carbon-fiber preforms impregnated in carbonized phenolic-formaldehyde matrix is modeled at microscopic scale. Direct numerical simulations show that the matrix ablates in volume leaving the carbon fibers exposed. This is due to the fact that the reactivity of carbonized phenolics is higher than the reactivity of carbon fibers. After the matrix is depleted, the fibers ablate showing progressive reduction of their diameter. The overall material recession occurs when the fibers are consumed. Two materials with the same carbon-fiber preform, density and chemical composition, but with different matrix distributions are studied. These studies show that at moderate temperatures (< 1000K) the microstructure of the material influences its recession rate; a fact that is not captured by current models that are based on chemical composition only. Surprisingly, the response of these impregnated-fiber materials is weakly dependent on the microstructure at very high temperatures (e.g., Stardust peak heating conditions: 3360K).

Lachaud, Jean↗
DOE OSTI2022

Dendrite-resolved, full-melt-pool phase-field simulations to reveal non-steady-state effects and to test an approximate model

In this report we study the epitaxial, columnar growth of (multiply oriented) dendrites/cells for a spot melt in a polycrystalline Al–Cu substrate using two-dimensional, phase-field, direct numerical simulations (DNS) at the full-melt-pool scale. Our main objective is to compare the expensive DNS model to a much cheaper but approximate “line” model in which a single-crystal phase-field simulation is confined to a narrow rectangular geometry. To perform this comparison, we develop algorithms that automatically extract quantities of interest (QoIs) from both DNS and line models. These QoIs allow us to quantitatively assess the assumptions in the line model and help us analyze its discrepancy with the DNS model. We consider four sets of heat source parameters, mimicking welding and additive manufacturing conditions, that create a combination shallow and deep melt pools. Our largest DNS simulation used 16K x 14K grid points in space. Our main findings can be summarized as follows. Under AM conditions, the QoIs of line models are in excellent agreement with the full DNS results for both shallow and deep melt pools. Under welding conditions, the primary spacing of the DNS model is smaller than the prediction of line model. We identify a geometric crowding effect that accounts for the discrepancies between the DNS and line models. We propose two potential mechanisms that determine the response of the microstructure to geometric crowding.

36 MATERIALS SCIENCE↗
NASA NTRS2021

Evaluation of Stereology for Snow Microstructure Measurement and Microwave Emission Modeling: A Case Study

Reliable microstructure measurement of snow is a requirement for microwave radiative transfer model validation. Snow specific surface area (SSA) can be measured using stereological methods, in which snow samples are cast in the field and photographed in the laboratory. Processing stereology photographs manually by counting intersections of test cycloids with air–ice boundaries reduces the problems in binary segmentation. This paper is a case study to evaluate the repeatability of the manually stereology interpretation by two independent research groups. We further assessed how uncertainty in snow SSA influences simulated brightness temperature(TB) driven by the Microwave Emission Model of Layered Snowpacks (MEMLS), and how stereology compares to Near Infrared (NIR) camera and hand lens. Data was obtained from two alpine snow profiles from Steamboat Springs, Colorado. Results showed that stereological SSA values measured by two groups are highly consistent, and the ground radiometer measured TBat 19 and 37 GHz was successfully predicted (RMSE<3.8 K);simulations using NIR SSA and hand-lens geometric grain size (Dg)measurements have larger errors. This conclusion was not sensitive to uncertainty in the free parameters of TB modeling.

Microwave radiometry↗