Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Multiscale, mechanistic modeling of irradiation-enhanced silver diffusion in TRISO particles

Tristructural isotropic (TRISO) particles are under consideration for use in several proposed advanced nuclear reactor concepts. The silicon carbide (SiC) layer in TRISO acts as a barrier to prevent the release of the fission products. However, despite remarkable retention, silver (Ag) release has been observed from intact particles, which requires investigation since the Ag isotope ( 110m Ag) has a long half-life. Previous work focused on developing a multiscale, mechanistic model for Ag diffusion accounting for temperature and microstructure effect and has been successfully validated. In this work, we expand the previous model to account for irradiation-enhanced Ag diffusivity in SiC and improve its accuracy over a wider grain size and temperature ranges relevant for advanced reactor conditions. A temperature, grain size, and flux dependent diffusivity is therefore derived using the mesoscale code MARMOT and implemented in the fuel performance code BISON. The irradiation-enhanced Ag diffusivity in SiC is compared against experimental data and validated using BISON against Ag release measurements from the Advanced Gas Reactor Fuel Development and Qualification Program (AGR-1 and AGR-2). Herein, we quantify the impact of SiC grain size, irradiation, and temperature on Ag release. In agreement with previous studies, we find accounting for SiC grain size improves agreement between BISON predictions and experimental observations for most cases. In conclusion, we also find that accounting for irradiation improves agreement for cases where Ag release was underestimated, but the impact was less significant than accounting for microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Matrix Microstructures in UHTC Composites

One of the major issues hindering the use of ultra high temperature ceramics for aerospace applications is low fracture toughness. There is considerable interest in developing fiber-reinforced composites to improve fracture toughness. Considerable knowledge has been gained in controlling and improving the microstructure of monolithic UHTCs, and this paper addresses the question of transferring that knowledge to composites. Some model composites have been made and the microstructures of the matrix developed has been explored and compared to the microstructure of monolithic materials in the hafnium diboride/silicon carbide family. Both 2D and 3D weaves have been impregnated and processed.

Johnson, Sylvia↗

Modeling of the Kinetics of Carbonitride Precipitation Process in High-Strength Low-Alloy Steels Using Cellular Automata Method

Proposition of a cellular automata (CA) model of carbonitride precipitation to simulate image of microstructure in HSLA steels and to predict the mechanical properties is presented in the paper. CA model proved to be very efficient in modeling various phenomena in material science. Numerical modeling played an important role in development of new processing technologies taking advantage of precipitation. By modeling, we mean a mathematical description of the relation between the main process variables and the resulting material properties, based on sound physical principles. In microalloyed steels, the microalloying elements Ti, Nb and V are added in order to control their microstructure and mechanical properties. High chemical affinity of these elements for interstitials (C, N) results in precipitation of binary compound, nitrides and carbides and products of their mutual solubility—carbonitrides. The model accounts for an increase in dislocation density due to plastic deformation and predicts kinetics of precipitation as well as shape of precipitates.

36 MATERIALS SCIENCE↗

Deep operator network surrogate for phase-field modeling of metal grain growth during solidification

A deep operator network (DeepONet) has been constructed that generates accurate representations of phase-field model simulations for evolving two dimensional metal grain morphology growing from melt. These representations serve as lower resolution, computationally efficient stand-ins for quick parameter space exploration of solutions to the the Allen-Cahn equations that dictate the phase-field model simulations. The experimental target for the phase-field model is a uranium casting system cooling a 434 g uranium charge from a maximum temperature of 1400° C at an average rate of 30° C / min , traversing the crystallographic phases of the pure metal. Experimental parameters inform the phase-field model, whose higher resolution computational model solutions are used to train the DeepONet in a given parameter space with the aim of developing a faster, more efficient method for predicting the solidifying metal's microstructure at different potential experimental values. The final DeepONet generates high accuracy, lower resolution predictions with cumulative relative approximation error over all timesteps of less than 0.5%, while ensuring solutions remain within physically feasible ranges. Further, these relative error values are comparable with other state-of-the-art DeepONet models for microstructure evolution, while significantly reducing the amount of training data required. Training a convolutional neural network simultaneously with the DeepONet, enforcing realistic values at the complex metal grain boundaries, and mathematically encoding boundary conditions into the structure of the DeepONet improved prediction accuracy and computational efficiency over a standard DeepONet model.

36 MATERIALS SCIENCE↗

Patch-Based Convolutional Neural Networks for Multiple Microstructural Features Detection in FIB-SEM Micrographs of Irradiated Nuclear Fuel

Focused ion beam scanning electron microscopy (FIB-SEM) tomography has increasingly been utilized for acquiring three-dimensional (3D) microstructure features at the sub-micron scale in irradiated nuclear materials. This technique involves sequential ion beam slicing followed by electron beam imaging and compositional mapping using energy dispersive spectroscopy (EDS). Despite its growing use, several challenges persist. These include the time-intensive nature of data collection of EDS data, difficulties in distinguishing between various microstructures, and issues with image alignment. These challenges currently limit the broader application of FIB-SEM tomography in the field. To overcome these limitations, we propose using convolutional neural networks (CNNs) to automate microstructure identification in SEM images. Our study introduces a new framework for identifying microstructures in irradiated U-10Zr (wt. %) metallic fuel with limited annotated data. The framework includes the creation of a reliable annotated dataset with paired SEM and ground truth data from EDS maps, the applications of CNNs for microstructure identification, and the validation of model performance. Specifically, we employed the Segment Anything Model (SAM) to align SEM images with corresponding EDS maps and focused ion beam (FIB) tomography SEM data. We evaluate several models, including Patch-based U-Net, Attention U-Net, and Residual U-Net, finding that patch-based U-Net exhibits superior segmentation performance and consistency. This approach reduces reliance on EDS detectors and aids in accelerating nuclear material analysis process, highlighting the potential of advanced deep learning techniques to improve microstructural understanding in nuclear material. This is the first framework to integrate SAM and Patch-based CNN models for semantic segmentation of irradiated nuclear materials, with potential applicability to other tomography datasets.

36 - MATERIALS SCIENCE↗

Effect of pore pressure buildup on slowness of rupture propagation

Pore fluid pressure is known to play an important role in brittle fracture initiation and propagation, yet the underlying mechanisms remain unclear. We conducted triaxial experiments on saturated porous sandstones to investigate effects of pore pressure buildup on the slowness of shear rupture propagation at different confining pressures. At low to intermediate confinements, rocks fail by brittle faulting, and pore pressure buildup causes a reduction in rock’s shear strength but does not induce measurable differences in slip behavior. When the confinement is high enough to prohibit dynamic faulting, rocks fail in the brittle-ductile transitional regime. In the transitional regime, pore pressure buildup promotes slip instability on an otherwise stably sliding fracture. Compared to those observed in the brittle regime, the slip rate, stress drop, and energy dissipated during rupture propagation with concurrent pore pressure buildup in the transitional regime are distinctively different. When decreasing confining pressure instead, the slip behavior resembles the ones of the brittle regime, emphasizing h ow the observed slowness is related to excess pore pressure beyond the effective pressure phenomenon. Analysis of the mechanical data using existing theoretical models confirms these observations. Quantitative microstructural analyses reveal that increasing pore pressure lessens the dilatancy hardening during failure, thus enhances slip along the localized zone in the transitional regime. Lastly, our experimental results suggest that pore pressure buildup induces slow slip in the transitional regime, and slip rates along a shear fracture may vary considerably depending on effective stress states.

58 GEOSCIENCES↗

Hot Deformation Behavior and Processing Map of a Fe-11Mn-10Al-0.9C Duplex Low-Density Steel Susceptible to κ-Carbides

The hot deformation behavior of a Fe-11Mn-10Al-0.9C duplex low-density steel has been investigated, based on a series of isothermal compression tests at temperatures of 800-1100 °C and strain rates of 0.001-10 s{sup −1}. At relatively lower temperatures, with austenite decomposing, continuous dynamic recrystallization of ferrite and the formation of inter-granular κ-carbide were responsible for significant softening. At high deformation temperature where austenite was a dominant phase, dynamic recrystallization (DRX) is the restoration mechanism. Processing maps were developed at different plastic strains employing dynamic materials model and further verified through microstructural characterization. The optimal hot deformation condition at a large strain (0.7) was identified as deformation temperature of 950-1100 °C and strain rate of 0.01-1.0 s{sup −1}. In this domain, the original coarse grains could be replaced by the fine and uniform recrystallized grains, indicating that the high efficiency was dissipated by DRX. Meanwhile, two instable regions resulted from the formation of inter-granular κ-carbides and necklace structure should be avoided during hot processing.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior and Processing Maps of As-Cast Hypoeutectic Al-Si-Mg Alloy

The hot deformation behavior of as-cast hypoeutectic Al-Si-Mg alloy has been investigated through hot compression tests at temperatures between 573 and 773 K and the strain rate of 0.001-1 s{sup −1}. A modified Hansel-Spittel constitutive model is proposed, which takes the effect of strain rate on strain hardening into account. The processing maps are established based on the dynamic material model and the Murty criterion. Microstructure observations show that dynamic recovery dominates the dynamic softening behavior, and recrystallized grains are found in the sample tested at 773 K with strain rate of 0.01 and 0.001 s{sup −1}. The size of Si particles decreases by about 64.73% with the effective strain increasing from 0 to 1.2. The optimal hot processing parameters of as-cast hypoeutectic Al-Si-Mg alloy are established based on the processing maps.

36 MATERIALS SCIENCE↗

Slip localization behavior at triple junctions in nickel-base superalloys

Incipient slip localization in the vicinity of hundreds of grain boundary triple junctions (TJs) in a lightly deformed nickel-base superalloy IN718 is studied using a combination of three-dimensional (3D) crystal plasticity finite element (CPFE) modeling, high resolution digital image correlation (HR-DIC) and 3D electron back-scatter diffraction tomography (3D EBSD). A 3D reconstruction method enables identification of thousands of TJs and correspondence of any observed slip bands with their originating TJ lines below the specimen surface. Here, we present a large-scale CPFE model of the experimental 3D microstructure composed of high-fidelity representation of the TJ lines and the boundaries and interiors of the parent grains and use it to calculate the local micromechanical response and slip activity of all TJs at the onset of macroscopic yielding. Statistical analysis of the calculated quantities reveal TJs develop larger stress concentration and grain-average re-orientation than grain interiors and grain boundaries, however no substantial differences in cumulative slip were found among these microstructural regions. We find that TJs with observed slip bands generate lower grain-average re-orientation, fewer active slip systems, and more localized slip on a single system than those without. The distinctions in the reorientation and slip activity are stronger in TJs that experience more intense slip.

36 MATERIALS SCIENCE↗

Influence of fine-scale B2 precipitation on dynamic compression and wear properties in hypo-eutectic Al0.5CoCrFeNi high-entropy alloy

The near equiatomic high-entropy alloys based on Al, Co, Cr, Fe, Ni have provided a novel microstructural template for alloy design. The face-centered cubic (FCC) matrix strengthened by body-centered cubic (BCC) based ordered B2 precipitates can be used to develop a new generation of precipitation strengthened alloys. The present study focuses on an Al0.5CoCrFeNi hypo-eutectic alloy consisting of an as-solidified FCC+B2 microstructure. Guided by solution thermodynamic modeling, this alloy has been isothermally aged for solid-state precipitation of a high fraction of fine-scale intragranular B2 particles. The dynamic compressive strength, hardness, and sliding wear response of the alloy as a function of B2 phase fraction is examined. The flow stress at 0.02% true strain increased from ~ 670 MPa to ~1350 (102%) MPa, the ultimate compressive strength increased from ~1160 MPa to 1500 MPa (20%), and the wear resistance increased more than 5 times with progressively increasing phase fraction of B2 precipitates.

Gwalani, Bharat↗

Analysis of radially resolved thermal conductivity in high burnup mixed oxide fuel and comparison to thermal conductivity correlations implemented in fuel performance codes

The thermal diffusivity and thermal conductivity of high burnup (19 % FIMA) mixed oxide (U, Pu)O 2 nuclear fuel has been measured along the radial direction using a thermoreflectance-based method. Measured thermal conductivity exhibits a notable radial variation consistent with the expectations that a large temperature gradient across the annular fuel pellet leads to a heterogeneous microstructure. A common fuel performance model of thermal conductivity, the Lucuta-Inoue model, is used to analyze the measured thermal conductivity profile. Further, this model adequately captures the radial dependence of thermal conductivity except in the periphery. The analysis suggests that the characteristic radial shape of the thermal conductivity profile follows the burnup profile within the fuel pin. In the periphery, the high burnup structure is formed and the conductivity model, not capturing this effect, likely overestimates the thermal conductivity.

36 MATERIALS SCIENCE↗

Enhanced strength and electrical conductivity of ultrafine-grained Al-Mg-Si alloy processed by hydrostatic extrusion

Highlights: • Al-Mg-Si alloy was subjected to hydrostatic extrusion combined with aging treatment. • UFG Al-Mg-Si alloy with UTS of 332 MPa and conductivity of 58% IACS was obtained. • Precipitation process depended on applied strains and crystallographic texture. • Strengthening effect was achieved by UFG structure and needle-like β″ precipitates. • Precipitation of β″ and spherical β′/β particles at GB provided high conductivity. - Abstract: The effect of hydrostatic extrusion combined with an artificial aging on microstructure, mechanical and electrical properties of 6101 Al-Mg-Si alloy was investigated. It has been shown that such thermo-mechanical treatment is an effective method for producing of long wires with an ultrafine-grained microstructure (grain size of 300–400 nm) and enhanced ultimate tensile strength (> 330 MPa) and electrical conductivity (up to 58% IACS). The mechanical behavior of 6101 Al-Mg-Si alloy depended strongly on applied strains by hydrostatic extrusion and crystallographic texture. Higher accumulative strain accelerated the precipitation kinetics but decreased the age hardening response. The double fiber <100> and <111> texture was observed for hydrostatically extruded samples. The <001> grains with homogenously distributed needle-like β″ precipitates provided precipitation strengthening of material while <111> grains resulted in more efficient grain boundary strengthening. Quantitative microstructure characterization allowed adjusting physical model to estimate the electrical conductivity and compare it with experimental data. The high conductivity was provided mainly by decomposition of solid solution due to precipitation of needle-like β″ precipitates in the grain interior and spherical β′ or β particles located at grain boundaries.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of Ti–6Al–4V: Mill-annealed versus direct metal laser melted alloys

Additive manufacturing processes such as direct metal laser melting (DMLM) are known to produce highly anisotropic microstructures. The present work compares the microstructure and mechanical properties of DMLM Ti–6Al–4V with that of mill-annealed alloys. Results show that the yield and hardening response of DMLM Ti–6Al–4V does not depend on the testing direction relative to the build direction, while the response of mill-annealed Ti–6Al–4V strongly depends on the testing direction. In conclusion, these results are discussed in light of the microstructure, texture, and polycrystal plasticity modeling.

36 MATERIALS SCIENCE↗

From classical thermodynamics to phase-field method

Phase-field method is a density-based computational method at the mesoscale for modeling and predicting the temporal microstructure and property evolution during materials processes. The focus of this article is on connecting the most common phase-field equations to the very basic first and second laws of classical thermodynamics through rudimentary irreversible thermodynamics. It briefly discusses the relations of the continuum phase-field equations to their counter parts at the microscopic and atomic levels. It attempts to clarify the contributions of long-range elastic, electrostatic, and magnetic interactions to domain structure evolution during structural, ferroelectric, and ferromagnetic phase transformations by separating order parameter changes due to the presence of quasi-static fields and those arising from phase transformations. A few examples are presented to demonstrate the possibility of employing the phase-field method to provide guidance to designing materials for optimum properties or discovering novel mesoscale phenomena or new materials functionalities. Here, the article ends with a brief perspective on a number of potential future directions on the development and applications of phase-field method beyond its traditional applications to structural alloys.

36 MATERIALS SCIENCE↗

Synchrotron Imaging of Pore Formation in Li Metal Solid-State Batteries Aided by Machine Learning

High-rate capable, reversible lithium metal anodes are necessary for next generation energy storage systems. In situ tomography of Li/LLZO/Li cells is carried out to track morphological transformations in Li metal electrodes. Machine learning enables tracking the lithium metal morphology during galvanostatic cycling. Nonuniform lithium electrode kinetics are observed at both electrodes during cycling. Hot spots in lithium metal are correlated with microstructural anisotropy in LLZO. Mesoscale modeling reveals that regions with lower effective properties (transport and mechanical) are nuclei for failure. Advanced visualization combined with electrochemistry represents an important pathway toward resolving non-equilibrium effects that limit rate capabilities of solid-state batteries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal conductivity of silicon nanowire arrays with controlled roughness

A two-step metal assisted chemical etching technique is used to systematically vary the sidewall roughness of Si nanowires in vertically aligned arrays. The thermal conductivities of nanowire arrays are studied using time domain thermoreflectance and compared to their high-resolution transmission electron microscopy determined roughness. The thermal conductivity of nanowires with small roughness is close to a theoretical prediction based on an upper limit of the mean-free-paths of phonons given by the nanowire diameter. The thermal conductivity of nanowires with large roughness is found to be significantly below this prediction. Raman spectroscopy reveals that nanowires with large roughness also display significant broadening of the one-phonon peak; the broadening correlates well with the reduction in thermal conductivity. The origin of this broadening is not yet understood, as it is inconsistent with phonon confinement models, but could derive from microstructural changes that affect both the optical phonons observed in Raman scattering and the acoustic phonons that are important for heat conduction. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4767456]

Feser, JP↗

Formation kinetics and thermodynamic stability of the Aurivillius compounds in Bi 4 Ti 3 O 12 –BiFeO 3 system

Abstract The Aurivillius compounds in the Bi 2 O 3 –Fe 2 O 3 –TiO 2 system, combining ferroelectric, semiconducting, and ferromagnetic properties, have attracted particular interest. Formation kinetics and thermodynamic stability are the fundamental knowledge needed for modeling and predicting the temporal microstructure and property evolution during materials processing but have not yet been addressed by quantitative experimental measurement. This article focuses on the Bi n +1 Fe n –3 Ti 3 O 3 n +3 Aurivillius compounds on the Bi 4 Ti 3 O 12 –BiFeO 3 tie‐line to elucidate the mechanisms and thermodynamic controls responsible for phase formation of compounds with various perovskite‐like layers. Five high‐purity Aurivillius compounds Bi 4 Ti 3 O 12 , Bi 5 FeTi 3 O 15 , Bi 6 Fe 2 Ti 3 O 18 , Bi 7 Fe 3 Ti 3 O 21 , and Bi 8 Fe 4 Ti 3 O 24 with integer n = 3–7 values were synthesized and their phase transformation properties and enthalpies of formation were studied by X‐ray diffraction in situ, high temperature differential scanning calorimetry, and high temperature oxide melt solution calorimetry. Thermodynamic stability of the compounds decreases with increasing n , and formation kinetics gradually slow down, demonstrating the inherent difficulty to synthesize pure Aurivillius compounds with n larger than 8. This difficulty was confirmed by an impurity phase coexisting with Bi 9 Fe 5 Ti 3 O 27 .

Gong, Weiping↗