SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Si reduction, purification and sheet generation work has been concentrated on gaining information about a reduction process combined with purification (higher purity arc furnace with gas blowing and gradient freezing), transport process with purification and polycrystal sheet growth potential (SiF2), plastic deformation for sheet generation, and float zone sheet recrystallization.
An analysis was made to determine the potential benefits of using a ceramic thermal insulation coating of calcia-stabilized zirconia on cooled engine parts. The analysis was applied to turbine vanes of a high temperature and high pressure core engine and a moderate temperature and low pressure research engine. Measurements made during engine operation showed that the coating substantially reduced vane metal wall temperatures. Evaluation of the durability of the coating on turbine vanes and blades in a furnace and engine were encouraging.
Ten advanced energy conversion systems for central-station, based-load electric power generation using coal and coal-derived fuels which were studied by NASA are presented. Various contractors were selected by competitive bidding to study these systems. A comparative evaluation is provided of the contractor results on both a system-by-system and an overall basis. Ground rules specified by NASA, such as coal specifications, fuel costs, labor costs, method of cost comparison, escalation and interest during construction, fixed charges, emission standards, and environmental conditions, are presented. Each system discussion includes the potential advantages of the system, the scope of each contractor's analysis, typical schematics of systems, comparison of cost of electricity and efficiency for each contractor, identification and reconciliation of differences, identification of future improvements, and discussion of outside comments. Considerations common to all systems, such as materials and furnaces, are also discussed. Results of selected in-house analyses are presented, in addition to contractor data. The results for all systems are then compared.
The following six highly energy intensive industries were studied as targets of energy conservation opportunity: food and kindred products, paper and allied products, chemicals and allied products, petroleum and coal products, stone, glass and clay products, and primary manufacturing. After studying conservation actions within each industry the actions were grouped under three broad categories: increased combustion efficiency, process improvement, and good housekeeping. Some of the results were: (1) approximately 2.18 quads could be saved in 1980 and 2.57 quads in 1985 by installing cogenerative facilities in 50% of the industries, (2) regenerative air-preheaters could result in a 10-15% increase in furnace efficiency representing a 15-25% fuel savings (2.3 to 3.9 quads in 1980 and 2.7 to 4.5 quads in 1985), (3) several major industries have potential for energy savings by recycling-aluminum (0.2 quads), steel (1 quad), glass (0.006 quads), paper and cement (0.08 quads).
The flight test furnace run of the monotectic and syntectic alloys experiment was successfully performed during the Apollo Soyuz Test Project mission. All three experiment cartridges were returned intact. A second ground based test was conducted after the mission to provide one g samples with an equivalent thermal history. The examinations of all flight and ground based cartridges and ampoules have been completed. Encouraging results have been obtained in the preliminary analysis of one flight aluminum antimonide sample as compared to ground based and prototype test counterparts. In terms of reduction of the unwanted second phase, the low g sample shows a homogeneity improvement by a factor of 5 to 20. Preliminary examination of one lead zinc flight sample shows a dispersion of lead in the zinc matrix. However, complete homogenization of the material did not occur. A thermal analysis of flight data shows that the average soak temperature for the head zinc ampoules was 20 C lower than planned but 35 C above the published consolute temperature..
Three vapor transport experiments on multicomponent systems were performed during the Apollo Soyuz mission to determine the effects of microgravity forces on crystal morphology and mass transport rates. The mixed systems used germanium selenide, tellurium, germanium tetraiodide (transport agent), germanium monosulfide, germanium tetrachloride (transport agent), and argon (inert atmosphere). The materials were enclosed in evacuated sealed ampoules of fused silica and were transported in a temperature gradient of the multipurpose electric furnace onboard the Apollo Soyuz spacecraft. Preliminary evaluation of 2 systems shows improved quality of space grown crystals in terms of growth morphology and bulk perfection. This conclusion is based on a direct comparison of space grown and ground based crystals by means of X-ray diffraction, microscopic, and chemical etching techniques. The observation of greater mass transport rates than predicted for a microgravity environment by existing vapor transport models indicates the existence of nongravity caused transport effects in a reactive solid/gas phase system.
An apertured casting is made by first forming a duplicate in the shape of the finished casting, positioning refractory metal bodies such as wires in the duplicate at points corresponding to apertures or passageways in finished products, forming a ceramic coating on the duplicate, removing the duplicate material, firing the ceramic in a vacuum or inert atmosphere, vacuum casting the metal in the ceramic form, removing the ceramic form, heating the cast object in an atmospheric furnace to oxidize the refractory metal bodies and then leaching the oxidized refractory bodies from the casting with a molten caustic agent or acid solution.
A data base for the comparison of advanced energy conversion systems for utility applications using coal or coal-derived fuels was developed. Estimates of power plant performance (efficiency), capital cost, cost of electricity, natural resource requirements, and environmental intrusion characteristics were made for ten advanced conversion systems. Emphasis was on the energy conversion system in the context of a base loaded utility power plant. All power plant concepts were premised on meeting emission standard requirements. A steam power plant (3500 psig, 1000 F) with a conventional coal-burning furnace-boiler was analyzed as a basis for comparison. Combined cycle gas/steam turbine system results indicated competitive efficiency and a lower cost of electricity compared to the reference steam plant. The Open-Cycle MHD system results indicated the potential for significantly higher efficiency than the reference steam plant but with a higher cost of electricity.
Both recuperated and bottomed closed cycle gas turbine systems in electric power plants were studied. All systems used a pressurizing gas turbine coupled with a pressurized furnace to heat the helium for the closed cycle gas turbine. Steam and organic vapors are used as Rankine bottoming fluids. Although plant efficiencies of over 40% are calculated for some plants, the resultant cost of electricity was found to be 8.75 mills/MJ (31.5 mills/kWh). These plants do not appear practical for coal or oil fired plants.
Specimens of gas saturated carbon tetrabromide were directionally solidified in a transparent furnace using a gradient freeze technique. The original temperature gradient was 5 C/cm and the cooling rate was 40 C/h. Progress of the experiment was monitored photographically. Gas bubbles were generated at the advancing solidification front in each of the three specimens. The gas bubbles were observed to increase in size, coalesce, and eventually be grown into the solid specimen under low gravity conditions. No bubble detachment from the interface was observed. Identical specimens processed in the laboratory showed bubble nucleation, bubble growth, and eventual bubble detachment due to buoyancy forces. Examination of the specimens showed a significantly greater void content in the low gravity processed samples. The grain size was observed to be finer in the low gravity processed samples.
Using a recently developed furnace, ferromagnetic resonance (FMR) thermomagnetic studies up to 900 C were employed to measure the Curie points of the superparamagnetic (SP) and single domain (SD) particles in lunar soils and potential magnetic analogue materials. Based on measured Curie points of 775 C, the SP and SD particles in lunar soils 10084-853, 12070-29, 14161-46, and 67010-4 are essentially pure metallic Fe. Synthetic and terrestrial samples containing magnetite, titanomaghemites, and magnetite-like particles have measured Curie points below 600 C are thus not magnetic analogues of lunar soils.
By adding an extra layer to multilayer beams or plates of different isotropic materials, it is possible to prevent the thermal bending of these materials. With the proper selection of thermoelastic properties the curvature produced prior to this addition would be eliminated. Several numerical examples are presented for various temperature distributions. A simple experiment was conducted, involving the addition of a brass strip to a bimetallic strip made of aluminum and steel at room temperature. The trimetal strip was placed in a furnace and remained straight for varying temperatures.
Results are presented for a study to determine the mechanisms involved in a high-temperature pack cementation process which provides a silicon carbide coating on a carbon-carbon composite. The process and materials used are physically and chemically analyzed. Possible reactions are evaluated using the results of these analytical data. The coating is believed to develop in two stages. The first is a liquid controlled phase process in which silicon carbide is formed due to reactions between molten silicon metal and the carbon. The second stage is a vapor transport controlled reaction in which silicon vapors react with the carbon. There is very little volume change associated with the coating process. The original thickness changes by less than 0.7%. This indicates that the coating process is one of reactive penetration. The coating thickness can be increased or decreased by varying the furnace cycle process time and/or temperature to provide a wide range of coating thicknesses.
The article deals with the thermal protection system (TPS) designed to keep Space Shuttle structures at 350 F ratings over a wide range of temperatures encountered in orbit, but also during prelaunch, launch, deorbit and re-entry, landing and turnaround. The structure, function, fabrication, and bonding of various types of reusable surface insulation and composite materials are described. Test programs are developed for insulation, seals, and adhesion bonds; leak tests and acoustic fatigue tests are mentioned. Test facilities include arc jets, radiant heaters, furnaces, and heated tunnels. The certification tests to demonstrate TPS reusability, structural integrity, thermal performance, and endurance will include full-scale assembly tests and initial orbital flight tests.
The absorption spectrum of Si I in the wavelength region between 1500 and 1900 A has been photographed at high resolution. The silicon vapor was produced in a 122-cm-long King furnace at 1800 to 2300 C. Forty-two Rydberg series have been observed from the ground state terms 3p(2)3P and 1D to terms associated with the 3pns and 3pnd configurations. All of the series from these configurations with J less than 4 have been extended with the 3pnd 3D(3) levels reaching n = 56. Numerous perturbations have been observed. This laboratory work has provided the basis for extending the identification of silicon lines in the solar spectrum. Nearly all lines found in the laboratory spectrum are also found in rocket spectrograms of the solar chromosphere. More than 300 lines have been attributed to Si I. The excellent correlation between laboratory and solar Si I lines is illustrated.
An experimental study was carried out to evaluate the effect of cyclic thermal exposures on the mechanical properties of a gamma/gamma prime-delta eutectic alloy parallel to the growth direction. The alloy had a nominal composition by weight of Ni-20 Nb-6 Cr-2.5 Al and was directionally solidified at 3 cm/hr in a furnace with a thermal gradient of at least 200 C/cm. Bars of the alloy were exposed in a Mach 0.3 burner rig and cycled 300 times between 1100 and 425 C. Oxidation-erosion characteristics of the alloy were determined by weight loss measurements at 300-cycle intervals. After cyclic exposure, stress rupture and tensile tests were performed at both 760 and 1040 C. Microstructural changes from cyclic exposure were determined. Thermal cycling resulted in gamma prime coarsening and Widmanstaetten delta precipitation in the gamma phase. An unidentified precipitate, presumably gamma prime, was observed within the delta phase. These microstructural changes did not affect the mechanical properties of the eutectic. High oxidation-erosion weight loss rate was observed.
Simple inexpensive thermometer, insolated from surroundings by transparent glass or plastic encasement, measures intensities of solar radiation, or radiation from other sources such as furnaces or ovens. Unit can be further modified to accomplish readings from remote locations.
The successful application of high creep strength, directionally solidified gamma/gamma prime-delta (Ni-19.7Cb-6Cr-2.5Al) eutectic superalloy turbine blades requires the development of suitable coatings for airfoil, root and internal blade surfaces. In order to improve coatings for the gamma/gamma prime-delta alloy, the current investigation had the goals of (1) refining promising coating compositions for directionally solidified eutectics, (2) evaluating the effects of coating/ substrate interactions on the mechanical properties of the alloy, and (3) evaluating diffusion aluminide coatings for internal surfaces. Burner rig cyclic oxidation, furnace cyclic hot corrosion, ductility, and thermal fatigue tests indicated that NiCrAlY+Pt(63 to 127 micron Ni-18Cr-12Al-0.3Y + 6 micron Pt) and NiCrAlY(63 to 127 micron Ni-18Cr-12Al-0.3Y) coatings are capable of protecting high temperature gas path surfaces of eutectic alloy airfoils. Burner rig (Mach 0.37) testing indicated that the useful coating life of the 127 micron thick coatings exceeded 1000 hours at 1366 K (2000 deg F). Isothermal fatigue and furnance hot corrosion tests indicated that 63 micron NiCrAlY, NiCrAlY + Pt and platinum modified diffusion aluminide (Pt + Al) coating systems are capable of protecting the relatively cooler surfaces of the blade root. Finally, a gas phase coating process was evaluated for diffusion aluminizing internal surfaces and cooling holes of air-cooled gamma/gamma prime-delta turbine blades.