Passivation Properties and Formation Mechanism of Amorphous Halide Perovskite Thin Films
Explore the source record for details and available documents.
Rigter, Susan A.↗
SEARCH · Engineering Papers
Results for “crystalline”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Multimodal Characterization of Crystal Structure and Formation in Rubrene Thin Films Reveals Erasure of Orientational Discontinuities
Abstract Multimodal multiscale characterization provide opportunities to study organic semiconducting thin films with multiple length scales, across multiple platforms, to elucidate crystallization mechanisms of the various microstructures that impact functionality. With polarized scanning transmission X‐ray and 4D‐scanning transmission electron microscopy, hybrid crystalline structures in rubrene thin films in which large crystalline domains surround a common nucleus and transition to a spherulite morphology at larger radii is observed. These high‐resolution techniques reveal how azimuthal orientational discontinuities at smaller radii are erased as spherulite morphology takes hold. In situ crystallization in the films with optical microscopy is also captured, discovering the importance of considering the initial temperature increase of a film during thermal annealing over the crystallization timescale. This kinetic information of the radial crystallization rate and of corresponding film heating kinetics is used to estimate the temperature at which the larger crystalline regions transition into a spherulite. By combining the results obtained from the different characterization modes, it is learned that thermal conditions can sensitively affect the crystallization of rubrene and other organic thin films. The observations suggest opportunities for more complex temperature‐dependent processing to maximize hybrid structures’ functionality in organic thin films and demonstrate that multimodal studies deepen the understanding of structure‐function dynamics.
Tan, Jenna A.↗
Stereochemically‐Controlled Fluorinated Copolymers for Selectively Permeable Barrier Applications
Selective oxygen permeability coupled with low water vapor transmission is essential for biomedical and packaging applications requiring controlled oxygen flux under humid conditions. However, most high‐performance barrier polymers depend on perfluoroalkyl substances (PFAS), whose persistence and regulatory restrictions limit their long‐term applicability. We designed a series of stereocontrolled thiol‐yne‐based polyesters, including both fluorinated and non‐fluorinated variants, for selective oxygen permeability with considerable water barrier performance. Tailoring polymer crystallinity and morphology tuned both oxygen transport and mechanical properties. Fluorinated polymers demonstrated enhanced hydrophobicity and water resistance while maintaining oxygen diffusivity within a range relevant to oxygen‐sensing applications. Structure–property relationships were elucidated through small‐ and wide‐angle X‐ray scattering, revealing semi‐crystalline domains influenced by fluorine content and dithiol chain length. Barrier performance was rigorously evaluated via water vapor transmission rate and dynamic vapor sorption, showing reduced water uptake with increasing dithiol monomer length and crystallinity. In conclusion, this work introduces a PFAS‐free alternative to conventional barrier materials and establishes a tunable materials platform with potential relevance for biomedical devices and packaging systems requiring controlled oxygen permeability.
36 MATERIALS SCIENCE↗
Machine Learning Guided Synthesis of Flash Graphene
Advances in nanoscience have enabled the synthesis of nanomaterials, such as graphene, from low-value or waste materials through flash Joule heating. Though this capability is promising, the complex and entangled variables that govern nanocrystal formation in the Joule heating process remain poorly understood. In this work, machine learning (ML) models are constructed to explore the factors that drive the transformation of amorphous carbon into graphene nanocrystals during flash Joule heating. An XGBoost regression model of crystallinity achieves an r 2 score of 0.8051 ± 0.054. Feature importance assays and decision trees extracted from these models reveal key considerations in the selection of starting materials and the role of stochastic current fluctuations in flash Joule heating synthesis. Furthermore, partial dependence analyses demonstrate the importance of charge and current density as predictors of crystallinity, implying a progression from reaction-limited to diffusion-limited kinetics as flash Joule heating parameters change. Finally, a practical application of the ML models is shown by using Bayesian meta-learning algorithms to automatically improve bulk crystallinity over many Joule heating reactions. Furthermore, these results illustrate the power of ML as a tool to analyze complex nanomanufacturing processes and enable the synthesis of 2D crystals with desirable properties by flash Joule heating.
01 COAL, LIGNITE, AND PEAT↗
Enhancement of the Magnetoresistance in the Mobility‐Engineered Compensated Metal Pt 5 P 2
Abstract The magnetoresistance (MR) in nonmagnetic materials continues to be a fertile research area in materials science. The search for giant, positive MR has been limited to a rather small window of materials such as high‐mobility semimetals in single‐crystalline form. Here, the observation of a very large positive MR in metallic Pt 5 P 2 in polycrystalline form is reported. The observations reveal that improvement of the crystallinity results in a significant enhancement of the positive MR, exceeding 10 000% at 9 T, comparable to high‐mobility semimetals. Based on first‐principles calculations combined with magnetotransport and thermoelectric measurements, the Fermi surface of Pt 5 P 2 is found to consist of a collection of multiple electron and hole pockets compensating one another, along with a characteristic pocket continuously connected to the adjacent Brillouin zone, together with possible topologically protected band crossings. This work extends the landscape of high MR candidate materials to polycrystalline metals, which demonstrates the importance of crystallinity and purity of the samples for the optimization of the MR.
36 MATERIALS SCIENCE↗
Mesocrystallizing Nanograins for Enhanced Li + Storage
Morphology and crystallinity of electrode materials have a major effect on their charge carrier storage properties when applied in rechargeable batteries. While nanosizing electrode particles (with larger surface area) and maintaining electrode integrity are both good for performance enhancement, they seem to contradict each other and can be hardly well-balanced. Herein, we designed electrode particles consisting of numerous nanograins with uniform crystalline orientation to guarantee both high surface area and high structural integrity, allowing the significant improvement of Li + storage kinetics and performance. Applying this “mesocrystallizing” strategy to a NiCo 2 O 4 -based anode, resulting in various degrees of pseudocapacitance response, the long-term cyclability and rate performance of this material have been largely enhanced. Impressively, the mesocrystalline NiCo 2 O 4 electrode exhibits a high reversible capacity of 1403 mAh g -1 after 200 cycles at 1.6 A g -1 (a rate of 1.8 C). The growth mechanism of mesocrystalline materials with different morphologies is identified to be a topotactic strctural transition process featuring a gradual edge-to-core corrasion process. This work presents an important synthetic clue to balance the morpholgy and crystallinity of battery electrode materials for their perforamnce optimization and is expected to inspire future structural design for battery materials beyond the one prototyped here.
25 ENERGY STORAGE↗
Few‐Unit‐Cell MFI Zeolite Synthesized using a Simple Di‐quaternary Ammonium Structure‐Directing Agent
Abstract Synthesis of a pentasil‐type zeolite with ultra‐small few‐unit‐cell crystalline domains, which we call FDP (few‐unit‐cell crystalline domain pentasil), is reported. FDP is made using bis‐1,5(tributyl ammonium) pentamethylene cations as structure directing agent (SDA). This di‐quaternary ammonium SDA combines butyl ammonium, in place of the one commonly used for MFI synthesis, propyl ammonium, and a five‐carbon nitrogen‐connecting chain, in place of the six‐carbon connecting chain SDAs that are known to fit well within the MFI pores. X‐ray diffraction analysis and electron microscopy imaging of FDP indicate ca. 10 nm crystalline domains organized in hierarchical micro‐/meso‐porous aggregates exhibiting mesoscopic order with an aggregate particle size up to ca. 5 μm. Al and Sn can be incorporated into the FDP zeolite framework to produce active and selective methanol‐to‐hydrocarbon and glucose isomerization catalysts, respectively.
Lu, Peng↗
Few‐Unit‐Cell MFI Zeolite Synthesized using a Simple Di‐quaternary Ammonium Structure‐Directing Agent
Abstract Synthesis of a pentasil‐type zeolite with ultra‐small few‐unit‐cell crystalline domains, which we call FDP (few‐unit‐cell crystalline domain pentasil), is reported. FDP is made using bis‐1,5(tributyl ammonium) pentamethylene cations as structure directing agent (SDA). This di‐quaternary ammonium SDA combines butyl ammonium, in place of the one commonly used for MFI synthesis, propyl ammonium, and a five‐carbon nitrogen‐connecting chain, in place of the six‐carbon connecting chain SDAs that are known to fit well within the MFI pores. X‐ray diffraction analysis and electron microscopy imaging of FDP indicate ca. 10 nm crystalline domains organized in hierarchical micro‐/meso‐porous aggregates exhibiting mesoscopic order with an aggregate particle size up to ca. 5 μm. Al and Sn can be incorporated into the FDP zeolite framework to produce active and selective methanol‐to‐hydrocarbon and glucose isomerization catalysts, respectively.
36 MATERIALS SCIENCE↗
Blocky Selective Postpolymerization C–H Functionalization of Polyolefins
C–H functionalization of commodity polyolefins affords functional materials derived from a high-volume, low-cost resource. However, current postpolymerization modification strategies result in randomly distributed functionalization along the length of the polymer backbone, which has a negative impact on the crystallinity of the resultant polymers, and thus the thermomechanical properties. Here, we demonstrate an amidyl radical mediated C–H functionalization of polyolefins to access blocky microstructures, which exhibit a higher crystalline fraction, larger crystallite size, and improved mechanical properties compared to their randomly functionalized analogues. Taking inspiration from the site-selective C–H functionalization of small molecules, we leverage the steric protection provided by crystallites and target polymer functionalization to amorphous domains in a semicrystalline polyolefin gel. The beneficial outcomes of blocky functionalization are independent of the identity of the pendant functional group that is installed through functionalization. Here, the decoupling of functional group incorporation and crystallinity highlights the promise in accessing nonrandom microstructures through selective functionalization to circumvent traditional tradeoffs in postpolymerization modification, with potential impact in advanced materials and upcycling plastic waste.
Neidhart, Eliza K. [The University of North Caroli↗
In Situ 4D‐STEM Imaging of the Orientation of Lamellar Clusters in Polymer Crystallization
In semi‐crystalline polymeric materials, the initial stages of nucleation and the growth path of crystalline domains can determine the final performance. Here, in this work, we used four‐dimensional scanning transmission electron microscopy (4D‐STEM) imaging to analyze the changes in lamellar orientation in high‐density polyethylene (HDPE) during heating and cooling. This method allowed us to quantitatively detect the formation of lamellae clusters with different in‐plane orientations, which are not visible with traditional methods. Our analysis provided detailed insights into the orientation and size changes of crystalline domains. Additionally, this technique enabled direct observation of lattice structures in hierarchical lamellae and the growth of crystals, confirming the local variability in lamellar orientation. This innovative approach significantly improves our understanding of polymer crystallization, linking changes in morphology and lattice structures at different length scales.
4D-STEM↗
Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)
A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Morphology, microstructure, and doping behaviour: A comparison between different deposition methods for poly-Si/SiO x passivating contacts
In this work, we study how crystallographic structures, optoelectronic properties, and nanoscale surface morphologies of ex situ phosphorus-doped polycrystalline silicon (poly-Si)/SiO x passivating contacts, formed by different deposition methods (sputtering, plasma-enhanced chemical vapour deposition [PECVD], and low-pressure chemical vapour deposition [LPCVD]), are investigated and compared. Across all these deposition technologies, we noted the same trend: higher diffusion temperatures yield films that are more crystalline but that have rougher surface morphologies due to bigger surface crystal grains. Also, the recrystallization process of the as-deposited Si films starts from the SiO x interface, rather than from the film surface and bulk. However, there are some distinct differences among these technologies. First, the LPCVD method yields the lowest deposition rate, roughest surfaces, and smallest degree of crystallinity on finished poly-Si films. In contrast, the PECVD method has the highest deposition rate and smoothest surfaces for both as-deposited Si and annealed poly-Si films. Second, as-deposited sputtered and PECVD Si films contain only an amorphous phase, whereas as-deposited LPCVD films already has some crystalline phase. Third, the LPCVD phosphorus in-diffusion into the substrate depends strongly on the initial film thickness, whereas for the other two methods, it is weakly dependent on thickness. Finally, the passivation quality of every poly-Si film type has different responses to the film thickness and diffusion temperature, suggesting that the ex situ doping optimization should be performed independently.
14 SOLAR ENERGY↗
Life cycle energy demand and carbon emissions of scalable single-junction and tandem perovskite PV
Perovskite photovoltaics reached record efficiencies in the laboratory and, if sustainably commercialized, they would accelerate a green energy transition. Here, this article presents the development of life-cycle inventory material and energy databases of most promising four single-junction and three tandem scalable perovskite systems with assumptions regarding scalable production validated by industry experts. We conducted comprehensive “ex ante” Life Cycle Analysis (LCA) and Net Energy Analysis, analyzing their cumulative energy demand, global warming potential profiles, energy payback times and energy return on investment (EROI). LCA contribution analysis elucidates the most impactful material and process choices. It shows that solution-based perovskite manufacturing would have lower environmental impact than vapor-based methods, and that roll-to-roll (RtR) printing offers the lowest impact. Among material choices, MoOx/Al has lower impact than Ag, and fluorine-tin-oxide lower than indium-tin-oxide. Furthermore, we compare perovskites with commercial crystalline-silicon and thin-film PV, accounting for the most recent developments in crystalline-Si wafer production and differences in life expectancies and efficiencies. It is shown that perovskite systems produced with RtR manufacturing could reach in only 12 years of life the same EROI as that of single-crystalline-Si PV lasting 30-years. This work lays a foundation for sustainability investigations of perovskite large-scale deployment.
14 SOLAR ENERGY↗
Elucidating the Role of Hydrogen at c‐In 2 O 3 /a‐In 2 O 3− x Interface
Ab initio molecular dynamics simulations and hybrid functional electronic structure calculations are employed to determine the formation, the structural and electronic properties, and the dynamics of covalent (In—OH) and ionic (In—H—In) hydrogen defects at crystalline-In 2 O 3 /amorphous-In 2 O 3−x interface. This comprehensive computational study considers (i) various interstitial and substitutional hydrogen site locations within the crystalline, amorphous, and interfacial regions; (ii) several oxygen-to-hydrogen ratios; and (iii) possible defect charged states. The results reveal hydrogen's inability to fully passivate the undercoordinated under-shared in atoms in amorphous highly substoichiometric oxide, giving rise to the formation of deep electron traps even in net-charge neutral structures. These trap defects are found to be sensitive to photoexcitation, in contrast to In—OH with H's electronic states located below the valence band and to In—H—In, where H is found to maintain its charge state upon illumination. Nevertheless, H plays a critical role in photoinduced conductivity and its relaxation by promoting In—O coordination transformations at the interfacial region, including deterioration of the crystalline layer. Finally, the results help identify mobile H species and metastable H defect complexes (such as In—H—H—In, In—OH–H—In, and In—OH–O—In) that are responsible for long relaxation times of the conductivity decay.
H defects↗
Reconfiguration of Amorphous Complex Oxides: A Route to a Broad Range of Assembly Phenomena, Hybrid Materials, and Novel Functionalities
This work demonstrate that reconfiguration of amorphous oxide layers drives the assembly of oxide-based and freestanding nanomembranes into 3D structures with a radius of a few hundred nanometers. Reconfiguration-driven assembly is a versatile approach to impart large strains and strain gradients in a broad palette of complex oxides. This capability allows for manipulating and enhancing ferroelectricity, flexoelectricity, piezoelectricity, superconductivity, and ferromagnetism in complex oxides. Moreover, by the approach presented in this work, strain-engineered oxides are obtained in the form of 3D structures that can be fabricated in parallel on any substrate, including large-area and single crystalline semiconductor substrates. This approach will create a vast expanse of possibilities to investigate and leverage strain-tunable effects in amorphous, poly-crystalline, and single-crystalline complex oxides. Reconfiguration-driven assembly of NMs also allows combining different materials in a radial geometry and through scalable processes. For example, radial superlattices of Si (or GaAs) and various complex oxides or alternating layers of different complex oxides (e.g., SrTiO 3 and LaAlO 3 ) could be fabricated by release and heating of bilayer NMs. Here, a broad palette of electronic band structures and spin–orbit interactions could then be obtained by tailoring the curvature of the self-assembled NMs and the materials that the heterostructure comprises.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Elucidating Structural Disorder in Ultra‐Thin Bi‐Rich Bismuth Oxyhalide Photocatalysts
Abstract Advancing the field of photocatalysis requires the elucidation of structural properties that underpin the photocatalytic properties of promising materials. The focus of the present study is layered, Bi‐rich bismuth oxyhalides, which are widely studied for photocatalytic applications yet poorly structurally understood, due to high levels of disorder, nano‐sized domains, and the large number of structurally similar compounds. By connecting insights from multiple scattering techniques, utilizing electron‐, X‐ray‐ and neutron probes, the crystal phase of the synthesized materials is allocated as layered Bi 24 O 31 X 10 (X = Cl, Br), albeit with significant deviation from the reported 3D crystalline model. The materials comprise anisotropic platelet‐shaped crystalline domains, exhibiting significant in‐plane ordering in two dimensions but disorder and an ultra‐thin morphology in the layer stacking direction. Increased synthesis pH tailored larger, more ordered crystalline domains, leading to longer excited state lifetimes determined via femtosecond transient absorption spectroscopy (fs‐TAS). Although this likely contributes to improved photocatalytic properties, assessed via the photooxidation of benzylamine, increasing the overall surface area facilitated the most significant improvement in photocatalytic performance. This study, therefore, enabled both phase allocation and a nuanced discussion of the structure‐property relationship for complicated, ultra‐thin photocatalysts.
Chemistry↗
Growth of Crystallographically Aligned PbSe Films of Controlled Thickness on Amorphous Substrates
Lead selenide (PbSe) has extensively been investigated due to its thermoelectric and photoconductive properties. More recently, predictions of emergent properties have focused synthetic efforts on preparing ultra-smooth layers of crystallographically aligned PbSe layers with a thickness equal to an integer number of monolayers. While rough films are typically formed through Volmer-Weber growth on heated substrates, we report the data presented herein indicates that a crystallographically aligned, ultrathin layer with a defined number of PbSe layers forms on mostly amorphous Mo-Se and V-Se coated Si substrates during nominally room temperature deposition. Since the films are uniform in thickness, the number of PbSe bilayers formed depends on the amount of Pb (or Se) deposited. If the amount of Pb deposited is close to that required for an integral number of unit cells and there is sufficient Se, Laue oscillations are present in the as-deposited samples. The Laue oscillations reflect the quality and uniformity of the crystalline PbSe domains. This study demonstrates that the substrate does not need to be crystalline to form uniform, crystallographically aligned, integer monolayer thick PbSe films. These results suggest that tuning the strength of interactions be-tween substrate and growing film is necessary to form smooth, crystallographically aligned layers. The substrate does not need to be crystalline for these interactions to be strong enough to enable growth of crystallographically aligned films.
36 MATERIALS SCIENCE↗
The preparation and characterization of chemically deuterium incorporated cotton fibers
Preparation of deuterium incorporated cellulose is a vital tool to investigate cellulose internal structure and to expand the application fields of cellulose materials. In this study, cellulosic cotton fibers with anti-rehydration (exchange-resistant) deuterium incorporated in cellulose were prepared by chemical hydrogen–deuterium exchange treatment. The chemical hydrogen–deuterium exchange process, along with exchange time, were characterized by nuclear magnetic resonance hydrogen spectroscopy (1H-NMR). The anti-rehydration deuterium incorporation was determined by Fourier Transform infrared spectroscopy (FTIR) and Stable Isotope Ratio Mass Spectrometer (IRSM). Here, the effect of the deuterium hydroxyl substitution on cotton fiber’s spectral data, microstructure, crystalline information, degree of polymerization, as well as it’s thermogravimetric analysis (charcoalization and combustion) are explored. Analysis of the chemical exchange process indicated that the hydrogen–deuterium exchange occurred preferentially in the amorphous cellulose component over the first several minutes. Deuterium exchange in the anti-rehydration crystalline phase took several hours. Increasing the treatment time, enhanced exchange-resistant deuterium incorporation to as high as about 60% of the cotton fibers’ cellulose hydroxyl groups was achieved. The characterization of FTIR, Fourier transform Raman (FT-Raman), and near-infrared spectra (NIR) all exhibited the deuterium spectral isotope effect on cellulose hydroxl groups. While, apart from the effect of reaction temperature, deuterium incorporation isotope effect did not affect the cellulose microstructure, crystalline index and the degree of polymerization properties. Furthermore, the thermogravimetric analysis of deuterated cotton fibers under N 2 and air atmosphere were both altered due to the thermodynamic isotope effect. These observations revealed the hydrogen–deuterium exchange treatment process and impacts on cellulose fiber properties, which helped us to better understand the cellulose internal structure and may facilitate the potential utilization of deuterated cellulosic materials.
59 BASIC BIOLOGICAL SCIENCES↗