Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conformance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Actuated forebody strake controls for the F-18 high alpha research vehicle

A series of ground-based studies have been conducted to develop actuated forebody strake controls for flight test evaluations using the NASA F-18 High-Alpha Research Vehicle. The actuated forebody strake concept has been designed to provide increased levels of yaw control at high angles of attack where conventional rudders become ineffective. Results are presented from tests conducted with the flight-test strake design, including static and dynamic wind-tunnel tests, transonic wind-tunnel tests, full-scale wind-tunnel tests, pressure surveys, and flow visualization tests. Results from these studies show that a pair of conformal actuated forebody strakes applied to the F-18 HARV can provide a powerful and precise yaw control device at high angles of attack. The preparations for flight testing are described, including the fabrication of flight hardware and the development of aircraft flight control laws. The primary objectives of the flight tests are to provide flight validation of the groundbased studies and to evaluate the use of this type of control to enhance fighter aircraft maneuverability.

Murri, Daniel G.↗
NASA NTRS1993

Structure and energetics of model amphiphilic molecules at the water liquid-vapor interface - A molecular dynamics study

A molecular dynamics study of adsorption of p-n-pentylphenol at infinite dilution at the water liquid-vapor interface is reported. The calculated free energy of adsorption is -8.8 +/- 0.7 kcal/mol, in good agreement with the experimental value of -7.3 kcal/mol. The transition between the interfacial region and the bulk solution is sharp and well-defined by energetic, conformational, and orientational criteria. At the water surface, the phenol head group is mostly immersed in aqueous solvent. The most frequent orientation of the hydrocarbon tail is parallel to the interface, due to dispersion interactions with the water surface. This arrangement of the phenol ring and the alkyl chain requires that the chain exhibits a kink. As the polar head group is being moved into the solvent, the chain length increases and the tail becomes increasingly aligned toward the surface normal, such that the nonpolar part of the molecule exposed to water is minimized. The same effect was achieved when phenol was replaced by a more polar head group, phenolate.

Pohorille, Andrew↗
NASA NTRS1993

On the aerodynamics and performance of active vortex generators

As a building block in the development of smart lift-enhancement devices, a new concept for flow control using active vortex generators (AVGs) is presented. Ramp, wedge, and doublet wedge (Wheeler) VG configurations are investigated. The AVGs are designed to conform to the surface of the wing section at low alpha. As the section approaches the stall, they are deployed and accordingly, alpha(stall) and C(lmax) are increased. A qualitative analysis of the flow around the various VG configurations was conducted in a low speed wind tunnel at 1.6 ft/s and a Reynolds number of approximately 3400. The results demonstrate that ramp VGs produce vortices that have the longest distance at breakdown. The VGs were also applied to a 25-in. span, 8-in. chord NACA 4415 wing section. Optimization studies were conducted on the spanwise spacing, chordwise position, and size of statically deployed VGs. The test results demonstrate a 14-percent increase in C(lmax) while increasing alpha (stall) by up to 3.

Barrett, Ron↗
NASA NTRS1991

Electromagnetic compatibility characterization of a BAe Stirling-cycle cryocooler for space application

This paper describes the electromagnetic compatibility (EMC) measurements of an 80-K Stirling-cycle cooler. The measurements, performed in the JPL EMC test facility, include dc magnetic field characterization, radiated magnetic and electric field emissions, and conducted emissions on the internal lines between the cooler electronics and the cooler. The measurements conform to both the MILSTD-461C specifications as well as to the specifications for the NASA Earth Observing System.

Johnson, Dean L.↗
NASA NTRS1993

Multi-scale roughness spectra of Mount St. Helens debris flows

A roughness spectrum allows surface structure to be interpreted as a sum of sinusoidal components with differing wavelengths. Knowledge of the roughness spectrum gives insight into the mechanisms responsible for electromagnetic scattering at a given wavelength. Measured spectra from 10-year-old primary debris flow surfaces at Mount St. Helens conform to a power-law spectral model, suggesting that these surfaces are scaling over the measured range of spatial frequencies. Measured spectra from water-deposited surfaces deviate from this model.

Austin, Richard T.↗
NASA NTRS1941

The calculation of span LCAD distributions of swept-back wings

Span load distributions of swept-back wings have been calculated. The method used was to replace the wing with a bound vortex at the quarter-chord line and to calculate the downwash due to the system of bound and trailing vortices to conform at the three-quarter-chord line to the slope of the flat-plate wing surface. Results are given for constant-chord and 5:1 tapered plan forms, for sweep-back angles of 0 degrees, 30 degrees, and 45 degrees, and for aspect ratios of 3, 6, and 9. Some comments on the stalling of swept-back wings are included.

Mutterperl, William↗
NASA NTRS1947

Experimental and calculated characteristics of three wings of NACA 64-210 and 65-210 airfoil sections with and without 2 degree washout

Report presents the results of an investigation conducted to determine some of the effects of airfoil section and washout on the experimental and calculated characteristics of 10-percent-thick wings. Three wings of aspect ratio 9 and ratio of root chord to tip chord 2.5 were tested. One wing had NACA 64-210 sections and 2 degree washout, the second had NACA 65-210 sections and 2 degree washout, and the third had NACA 65-210 sections and 0 degree washout. It was found that the experimental characteristics of the wings could be satisfactorily predicted from calculations based upon two-dimensional data when the airfoil contours of the wings conformed to the true airfoil sections with the same high degree of accuracy as the two-dimensional models.

AIRFOILS - NACA 65-210 - CHAR & MOMENTS LOW-DRAG↗
NASA NTRS1922

Lessons of the glider meets

While light loading was assumed to be the optimal conformation from previous meets, subsequent meets have shown that heavier loading produced better results.

Warner, Edward P↗
NASA NTRS1953

The Aerodynamic Design and Calibration of an Asymmetric Variable Mach Number Nozzle with a Sliding Block for the Mach Number Range 1.27 to 2.75

A method of designing as asymmetric, fixed geometry, variable Mach number nozzle has been developed by using the method of characteristics. A small nozzle conforming to the analytically determined ordinates was constructed and calibrated over a range of Mach numbers extending from 1.27 to 2.75. The results show the variation in Mach number to be plus or minus 0.01 or less and in the flow direction to be plus or minus 0.2 degrees within the test section. The range of Mach numbers from 1.27 to 2.75 was obtained by translating the lower block in a straight line parallel to the test-section center line for a distance of 2.17 test-section heights.

NOZZLES↗
NASA NTRS1946

Numerical procedures for the calculation of the stresses in monocoques III : calculation of the bending moments in fuselage frames

This report deals with the calculation of the bending moments in and the distortions of fuselage rings upon which known concentrated and distributed loads are acting. In the procedure suggested, the ring is divided into a number of beams each having a constant radius of curvature. The forces and moments caused in the end sections of the beams by individual unit displacements of the end sections are listed in a table designated as the operations table in conformity with Southwell's nomenclature. The operations table and the external loads are equivalent to a set of linear equations. For their solution the following three procedures are presented: 1) Southwell's method of systematic relaxations. This is a step-by-step approximation procedure guided by the physical interpretation of the changes in the values of the unknown. 2) The growing unit procedure in which the individual beams are combined successively into beams of increasing length until finally the entire ring becomes a single beam. In each step of the procedure a set of not more than three simultaneous linear equations is solved. 3) Solution of the entire set of simultaneous equations by the methods of the matrix calculus. In order to demonstrate the manner in which the calculations may be carried out, the following numerical examples are worked out: 1) Curved beam with both its end sections rigidly fixed. The load is a concentrated force. 2) Egg-shape ring with symmetric concentrated loads. 3) Circular ring with antisymmetric concentrated loads and shear flow (torsion of the fuselage). 4) Same with V-braces incorporated in the ring. 5) Egg-shape ring with antisymmetric concentrated loads and shear flow (torsion of the fuselage). 6) Same with V-braces incorporated in the ring. The results of these calculations are checked, whenever possible, by calculations carried out according to known methods of analysis. The agreement is found to be good. The amount of work necessary for the solution of ring problems by the methods described in the present report is practically independent of the degree of redundancy of the structure. For this reason the methods are recommended for use particularly in problems of rings having one or more internal bracing elements.

LOADS - FUSELAGES↗
NASA NTRS1949

Altitude performance of AN-F-58 fuels in J35-C-3 single combustor

Three fuel blends conforming to AN-F-58 specifications were tested in order to determine the influence of boiling temperatures and aromatic content on altitude performance in single combustor of 4000-pound-thrust turbojet engine. At simulated engine conditions from an altitude of 30,000 to an altitude of 60,000 feet and 85-percent rated engine speed, the three AN-F-58 fuels showed little difference in performance.

COMBUSTION - EFFECT OF ENGINE OPERATING CONDITIONS↗
NASA NTRS1949

Altitude performance of AN-F-58 fuels in J33-A-21 single combustor

Three fuels conforming to AN-F-58 specification were investigated in order to determine the influence of boiling temperatures and aromatic content on altitude performance in single combustor of a 4600-pound-thrust turbojet engine. Combustion efficiencies of the three AN-F-58 fuels were approximately equal at each simulated engine condition for altitudes from 5,000 to 50,000 feet, 90-percent normal rated engine speed, and flight Mach numbers of 0.0 and 0.6.

FUELS - PHYSICAL PROPERTIES↗
NASA NTRS1951

Flow through cascades in tandem

An exact treatment of the problem of finding the incompressible, inviscid two-dimensional flow around two cascades in tandem is presented. The analysis includes solutions of both the direct and the inverse problems. These problems are solved by conformally mapping the tandem cascade onto the region between two concentric circles in which region there are suitably placed flow singularities. Formulas for the velocity and the potential in the annular region are presented in a closed form by means of elliptic functions. The equations are presented in a form suitable for computation.

Spraglin, William E↗
NASA NTRS1927

Drag measurements on a Junkers wing section : application of the Betz Method to the results of comparative tests made on a model and on an airplane in flight

The comparison of model tests in flight can be based on the result of such measurements. They are very important from the aerodynamical point of view, as they lead to useful conclusions regarding the behavior of the wing, its best shape and the conformity of theoretical and actual flow. Although there still remains a certain prejudice against such measurements, I have still attempted to make these comparative tests in order to inspire confidence in their reliability.

WINGS - JUNKERS A 20↗
NASA NTRS1952

Theoretical damping in roll and rolling moment due to differential wing incidence for slender cruciform wings and wing-body combinations

A method of analysis based on slender-wing theory is developed to investigate the characteristics in roll of slender cruciform wings and wing-body combinations. The method makes use of the conformal mapping processes of classical hydrodynamics which transform the region outside a circle and the region outside an arbitrary arrangement of line segments intersecting at the origin. The method of analysis may be utilized to solve other slender cruciform wing-body problems involving arbitrarily assigned boundary conditions. (author)

Adams, Gaynor J↗
NASA NTRS1924

The Aerodynamic Plane Table

This report gives the description and the use of a specially designed aerodynamic plane table. For the accurate and expeditious geometrical measurement of models in an aerodynamic laboratory, and for miscellaneous truing operations, there is frequent need for a specially equipped plan table. For example, one may have to measure truly to 0.001 inch the offsets of an airfoil at many parts of its surface. Or the offsets of a strut, airship hull, or other carefully formed figure may require exact calipering. Again, a complete airplane model may have to be adjusted for correct incidence at all parts of its surfaces or verified in those parts for conformance to specifications. Such work, if but occasional, may be done on a planing or milling machine; but if frequent, justifies the provision of a special table. For this reason it was found desirable in 1918 to make the table described in this report and to equip it with such gauges and measures as the work should require.

Zahm, A F↗