Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Carbon, Nitrogen, and Sulfur Analysis of the Cetama Viognier Standard Reference Material

The Viognier sample was analyzed for C, N, and S concentrations and stable isotope compositions using an Elementar Vario Isotope Cube Elemental Analyzer (EA) that is coupled to an IsoPrime PrecisION IRMS. Powder samples were placed in tin capsules and then loaded onto a rotary autosampler. The autosampler dropped samples into the EA, and samples were combusted at 1175 °C over tungsten oxide in a continuous stream of helium carrier gas. A pulse of oxygen is added to the gas stream resulting in flash combustion of the tin capsule containing the sample, which raises the reaction temperature to approximately 1800 °C for a few seconds. The combustion reaction produces SO 2 , N 2 and CO 2 from any sulfur, nitrogen and carbon present in the sample. The resulting gases were then passed through a reduced copper reactor that was heated to 850 °C, to reduce NO x to N 2 , reduce SO 3 to SO 2 , and trap any volatile halogen compounds on silver wool. Following water removal using an adsorption tube, the N 2 , CO 2 , and SO 2 analyte gases were separated and purified using purge-trap columns. The purified gases were then carried through a thermal conductivity detector. The detector signal was passed to software that calculated elemental abundances based on integrated peak areas. The sample gases were then passed to the IRMS and stable isotope ratios were measured. Raw sample peak areas were corrected by subtracting the average peak area from blanks consisting of empty tin capsules run using the same EA analysis method. Blanks were also run following each replicate to verify that all the material was combusted. The Viognier sample was analyzed in triplicate on two days (target sample masses: 30, 60 and 90 mg). The following standards were analyzed to calibrate EA-IRMS measurements: IAEA-C6, USGS-40, USGS-41, IAEA-S1, and IAEA-S2.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Gas-Phase Composition as a Predictive Metric for Calendar Life Behavior of Next-Generation Silicon Anodes

The expansion of renewable technologies and electrification of the transportation sector is driving increased demand for next-generation battery materials that provide higher power and energy density with superior cycling and calendar life stability. Silicon (Si) has a theoretical capacity nearly 10x that of graphite, and is therefore a promising anode material candidate to meet these rigorous performance demands. While leading Si anode battery demonstrations are approaching target metrics for cycle life, a series of complex and interrelated modes of reactivity lead to reduced calendar life and therefore challenge practical adoption of these materials. Deconvoluting the degradation processes that impact Si calendar life is critical to informing the rational and accelerated design of improved Si materials. In the present work, we employ novel sampling techniques and GC-MS-FID characterization to measure gas-phase composition during initial Si cycling, which we tie to selective mechanisms of Si passivation. We utilize a tiered analysis approach to identify and quantify the gas-phase reaction products associated with three advanced Si material candidates under practical operating conditions. Ex situ analysis of Si powders (pure chemical reactivity) is coupled with nondestructive in situ sampling of Si electrodes in a practical pouch-cell format (coupled chemical and electrochemical reactivity). We link the observed gas-phase species evolution to electrochemical behavior and measured calendar life of the three Si materials. Further, we evaluate the voltage-resolved evolution of gas-phase species for one such Si nanomaterial, where nonmonotonic gas generation implies competition between passivating reaction pathways. The measured gas-phase compositional data serves as a critical input for our advanced electrochemical SEI models to identify favorable vs unfavorable reaction pathways to stabilize Si. In addition to bolstering a fundamental understanding of Si reactivity, the present approach informs specific and quantifiable gas-phase metrics tied to calendar life improvements in Si, which can streamline and accelerate the process of next-generation material development.

DIRECT ENERGY CONVERSION,ENERGY STORAGE↗
DOE OSTI2025

Short-range order and longer-range disorder revealed in germanium–tin alloy thin films by extended x-ray absorption fine structure analysis

Short-range order (SRO) in semiconductor alloys, a relatively under-studied structural phenomenon in which local atomic arrangements differ from those of a random solid solution, is investigated in molecular beam epitaxy (MBE)-grown GeSn thin films. A novel preparation technique is used to pattern these films into microscale ribbons that are released from the substrate for extended x-ray absorption fine structure (EXAFS) analysis. The results indicate a strong SRO in which the first shell around Sn atoms is greatly denuded of Sn atoms relative to the nominal atomic composition of the alloy. This effect is more pronounced than that observed recently in GeSn nanowires grown by chemical vapor deposition. Additionally, the presence of a longer-range disorder detected by EXAFS analysis in the shells of atoms more distant from the absorbers is indicative of the defects and inhomogeneous strain present in the MBE-grown films. The evident existence of the SRO in GeSn alloys deposited by different growth methods and in different strain states suggests that SRO is a general phenomenon in the thin films of this metastable solid solution.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Thermal Properties of Sodium Borosilicate Glasses as a Function of Sulfur Content

SO3 additions, up to 3.0 wt%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO2-10Al2O3-12B2O3-21Na2O-7CaO (wt%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.5 wt% SO3. It was found that sulfur (here as sulfate) in this glass increased the glass transition temperature, thermal diffusivity, heat capacity, and thermal conductivity, and decreased the mass density. Structural analysis, performed with Raman spectroscopy, indicated that the borosilicate network polymerized with sulfur additions, presumably due to Na2O being required to charge compensate the ionic SO42- additions, thus becoming unavailable to form non-bridging oxygen in the silicate network. It is postulated that this increased crosslinking of the borosilicate backbone lead to a structure with higher dimensionality and average bond energy. This increased the mean free paths and vibration frequency of the phonons, which resulted in the observed increase in thermal properties.

Thermal properties, Borosilicate glass, Sulfur sol↗
DOE OSTI2023

Data-driven analysis and prediction of stable phases for high-entropy alloy design

High-entropy alloys (HEAs) represent a promising class of materials with exceptional structural and functional properties. However, their design and optimization pose challenges due to the large composition-phase space coupled with the complex and diverse nature of the phase formation dynamics. In this study, a data-driven approach that utilizes machine learning (ML) techniques to predict HEA phases and their composition-dependent phases is proposed. By employing a comprehensive dataset comprising 5692 experimental records encompassing 50 elements and 11 phase categories, we compare the performance of various ML models. Our analysis identifies the most influential features for accurate phase prediction. Furthermore, the class imbalance is addressed by employing data augmentation methods, raising the number of records to 1500 in each category, and ensuring a balanced representation of phase categories. The results show that XGBoost and Random Forest consistently outperform the other models, achieving 86% accuracy in predicting all phases. Additionally, this work provides an extensive analysis of HEA phase formers, showing the contributions of elements and features to the presence of specific phases. We also examine the impact of including different phases on ML model accuracy and feature significance. Notably, the findings underscore the need for ML model selection based on specific applications and desired predictions, as feature importance varies across models and phases. This study significantly advances the understanding of HEA phase formation, enabling targeted alloy design and fostering progress in the field of materials science.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In–Depth Analysis of the Degradation Mechanisms of High–Nickel, Low/No–Cobalt Layered Oxide Cathodes for Lithium–Ion Batteries

A rational compositional design of high-nickel, cobalt-free layered oxide materials for high-energy and low-cost lithium-ion batteries would be expected to further propel the widespread adoption of electric vehicles (EVs), yet a composition with satisfactory electrochemical properties has yet to emerge. The previous work has demonstrated a promising LiNi 0.883 Mn 0.056 Al 0.061 O 2 (NMA-89) composition that outperformed high-nickel, cobalt-containing analogs in cycling stability and maintained a comparable rate performance and thermal stability. Herein, the capacity fading mechanism of NMA-89 in a pouch full cell with a 4.2 V cutoff is compared to that of its cobalt-containing analogs. The results reveal that particle cracking in LiNi 0.89 Mn 0.055 Co 0.055 O 2 (NMC-89) and LiNi 0.883 Co 0.053 Al 0.064 O 2 (NCA-89) leads to a loss of active material and an increase in surface area, thereby exacerbating structural and surface instabilities, accelerating impedance and polarization growth, and ultimately reducing their capacity retentions. LiNi 0.89 Mn 0.044 Co 0.042 Al 0.013 Mg 0.011 O 2 (NMCAM-89) and NMA-89 experience subdued surface reactions and maintain spherical particle structures, both of which are conducive to their capacity retentions during long-term cycling. Furthermore, this investigation offers insights into how specific transition-metal ions dictate the electrochemical stability of high-Ni layered oxide cathode materials, highlights the benefit of Mn-Al combination in NMA-89, and presents potential strategies to further enhance the performance of this novel class of cathode materials.

degradation mechanisms↗
DOE OSTI2021

Estimating Internal Stress of an Alteration Layer Formed on Corroded Boroaluminosilicate Glass through Spectroscopic Ellipsometry Analysis

Aqueous corrosion of glass may result in the formation of an alteration layer in the glass surface of which chemical composition and network structure are different from those of the bulk glass. Since corrosion occurs far below the glass-transition temperature, the alteration layer cannot fully relax to the new structure with the lowest possible energy. Molecular dynamics simulations suggested that such a network will contain highly strained chemical bonds, which can be manifested as a stress in the alteration layer. Common techniques to measure stress in thin films or surface layers were found inadequate for thick monolithic glass samples corroded in water. Here, we explored the use of spectroscopic ellipsometry to test the presence of internal stress in the alteration layer formed by aqueous corrosion of glass. Furthermore, a procedure for analyses of spectroscopic ellipsometry data to determine birefringence in the alteration layer was developed. Findings with the established fitting procedure suggested that a stress builds up in the corroded surface layer of a boroaluminosilicate glass if there is a change in relative humidity, pH, or electrolyte concentration of the environment to which the glass surface is exposed. A similar process may occur in other types of glass, and it may affect the surface properties of corroded glass objects.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

A Life Cycle Analysis Framework for Point Source Capture Systems

NETL studies the costs and benefits of PSC for electricity, industry, and mobile applications. Mobile point source capture (MPSC) and storage applied to freight modes captures emissions directly from exhaust. This poster presents a framework for conducting LCA of PSC systems applied to heavy-duty trucks, freight trains, and marine vessels. The framework defines a wheels-to-storage (gate-to-grave) boundary, including energy demands (electricity, heat, and cooling requirements), solvent use and cycling, onboard system components, carbon storage in a saline aquifer, and upstream manufacturing impacts for equipment, with a suggested functional unit of 1 tonne-km. Potential data sources for analysis include material, energy, and operational data from Oak Ridge National Laboratory, GREET (Greenhouse gases, Regulated Emissions, and Energy use in Technologies) model, and scientific literature. The suggested analytical approach includes comparison to publicly available business-as-usual systems without capture across all modes of transportation, sensitivity to composition of the capture solvent, and sensitivity to capture rate variation, all of which would support a wholistic PSC business case analysis. For future consideration, analysis can be augmented with consideration of different sources of electricity (e.g., nuclear), fuel substitution, deploying supportive infrastructure such as pipeline offloading points, and downstream applications like enhanced oil recovery (EOR).

life cycle analysis (LCA)↗
DOE OSTI2021

Experimental Evaluation of Deformation and Fracture Mechanisms in Highly Irradiated Austenitic Steels

The present report documents recent experimental results of analysis using scanning electron microscopy/electron backscatter diffraction (SEM-EBSD) of plastic deformation mechanisms and strain localization phenomena in austenitic steels irradiated by neutrons. Experiments were performed with specimens irradiated to 125 dpa and, additionally, with specimens that experienced radiation-induced swelling up to 3%. Section 1 briefly analyzes the deformation localization in irradiated steels and its consequences on the material performance. The section describes the advantages and importance of the SEM-EBSD approach combined with in situ mechanical testing capability. Section 2 briefly introduces the experimental tools and methods (i.e., SEM/EBSD in situ tensile frame, electric discharge machine to manufacture irradiated specimens) and describes the investigated materials (i.e., element composition, irradiation conditions, and general microstructure). Section 3 describes the key experimental results and provides a brief analysis and comparison with the datasets obtained earlier within the same task (i.e., low-dose specimens). The discussion focuses on EBSD microstructure maps with strain localization features, misorientation evolution as a function of strain, and observed deformation mechanisms. Section 4 evaluates data collected in recent years on highly irradiated steel and estimates the possible misorientation evolution under irradiation. The section introduces and discusses the concept of in-service-induced damage as an irradiation-assisted stress-corrosion cracking precursor. Section 5 summarizes the work performed. As expected, the present work results are beneficial for exploring and understanding degradation mechanisms in highly irradiated in-core materials found in light water reactors after long-term in-service life.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Evolved Gas Analysis–Mass Spectrometry Exposes Polymer Network Structures

Polymer network structures in epoxy thermosets play an important role in the final thermoset material properties. However, analytical characterization of these network structures is difficult due to their amorphous nature. In this work, the application of evolved gas analysis–mass spectrometry (EGA-MS) to characterize the polymer network structures of bisphenol A (BPA)-based thermosets is demonstrated. Analytical characterization of the polymer network structures is accomplished by monitoring the Product-Specific Kinetics (PSK) of BPA monomer formation during thermal degradation investigations. We relate observed differences in the activation energy (E a ) of BPA monomer formation to the local packing environment around the BPA monomer units within the polymer network. Variations in the local environment related to the polymer networks manifest qualitatively as broadening in the thermal profile of the BPA monomer evolution and quantitatively as changes in the activation energy (E a ). Three BPA thermoset formulations were investigated; two amine-cured thermoset with 4,4′-diaminodiphenylmethane (DDM) or poly(propylene glycol) bis(2-amino-propyl ether) (PPG400) and a homopolymerized thermoset via curing with Epikure 3253 catalyst (3253). Results revealed that the 3253 thermoset contained two distinct packing densities in the polymer network, while DDM and PPG400 thermosets had uniform distributions of packing densities. Results from the DDM thermoset revealed a gradually decreasing E a , while the apparent E a of PPG400 was consistent over the entire degradation. Furthermore, these differences in E a were concluded to stem from the flexibility of the corresponding polymer networks and the ability of the network components to rearrange and occupy formed voids. Due to the minimal sample required for analysis (100–200 μg), this EGA-MS technique has great potential for postproduction evaluation of composite parts to identify changes in the polymer networks from use and aging, which could signal compromised performance.

Degradation↗
DOE OSTI2025

Extreme Thermal Stabilization of Carborane–Cyanate Composites via B–N Dative-Bonded Boroxine Barriers

Enhancing the thermal stability of cyanate ester (CE) resins is crucial for high-temperature aerospace applications. This study elucidates the degradation mechanisms of CE composites reinforced with carborane additives, focusing on the formation of boron–nitrogen (B–N) dative bonds and their role in improving thermal resistance. Using thermogravimetric analysis, we examined char formation and evolved gases at multiple degradation stages. Reaction sequences and char products were characterized via Fourier transform infrared spectroscopy (FTIR), solid-state 13C and 11B NMR, and evolved gas analysis using mass spectrometry and FTIR. The solid-state 11B NMR was instrumental in detecting various boron oxidation states and the formation of B–N dative bonds during decomposition. These bonds facilitate cross-linking in the char phase, enhancing material integrity at elevated temperatures. However, in inert environments, the volatility of boron additives like carborane limits their effectiveness. These findings advance the understanding of CE composite degradation mechanisms and offer critical insights for developing high-temperature-resistant materials for aerospace applications.

Fourier transform infrared spectroscopy↗
DOE OSTI2020

Dynamic Life-Cycle Analysis of Fast Pyrolysis Biorefineries: Impacts of Feedstock Moisture Content and Particle Size

The commercialization of biorefineries has been met with significant obstacles due to the technical difficulties of handling solid biomass feedstocks, which are highly variable in physical properties and chemical compositions. An understanding of the principles of unit operations along the supply chain is key to the success of the biofuel industry. This study applies a dynamic life-cycle analysis (DLCA) methodology by developing quantitative relationships between the inputs and outputs for each unit operation based on scientific understanding of the causal effects. Using the DLCA, we assessed system sustainability of drop-in fuel production from fast pyrolysis of pine residues followed by hydro-processing. Life-cycle greenhouse gas (GHG) emissions were calculated for 4641 runs involving two key feedstock parameters: moisture content after field drying and particle size of the feed to pyrolyzer. Moisture contents varied between 25% and 35%, while particle sizes varied between 0.5 and 5 mm in these runs. The life-cycle GHG emissions of these cases vary from 22 to 40 g/MJ. Close examination of each unit operation's contribution to the total GHG emissions reveals that low moisture content after field drying produces savings in energy consumption during feedstock transportation and on-site drying. However, although small particle size leads to overall higher fuel yield, it also requires a significant amount of energy for feedstock size reduction and fuel production. The energy penalty outweighs the benefit of increased fuel yields, especially when fine particles (<1 mm) are used for pyrolysis; thus, small particle size leads to increased GHG emissions overall. The results highlight the trade-offs between the energy demand for preprocessing and the conversion yields, which can be addressed with DLCA.

09 BIOMASS FUELS↗
DOE OSTI2025

Demographic drivers of gut microbiome diversity

Abstract The gut microbiome plays a central role in orchestrating metabolic, immune, and neurological functions essential for human health. While extensive research has explored the effects of diseases and pathological conditions on gut microbiome composition, the influence of demographic factors remains underexplored, limiting our understanding of microbiome variations in disease states. This study addresses this gap by investigating the impact of demographic variables, including age, sex, and geography, on gut microbiome diversity in healthy individuals. Using the American Gut Project’s extensive dataset and the QIIME2 bioinformatics pipeline, we conducted a comprehensive analysis of microbial profiles across diverse demographic groups. Our results revealed significant age-related shifts in microbial richness and composition, and geographic location strongly influenced phylogenetic diversity. In contrast, sex exhibited limited impact on microbial diversity within healthy BMI ranges. These findings highlight the critical role of demographic factors in shaping gut microbiome diversity, providing a foundational framework to better contextualize disease-related microbiome variations and advance personalized healthcare approaches.

Biotechnology & Applied Microbiology↗
DOE OSTI2020

Analysis of the sludge batch 9 (Macrobatch 10) DWPF pour stream glass sample

A pour stream (PS) sample taken during processing of Sludge Batch 8 (SB8, Macrobatch 10) was analyzed by Savannah River National Laboratory (SRNL) to verify compliance with the Defense Waste Processing Facility (DWPF) Glass Product Control Program. The following conclusions were drawn from these analyses; The sum of oxides for the SB8 PS glass (97.41 wt%) is within the Product Composition Control System (PCCS) limits (100 ± 5 wt%); The average Waste Dilution Factor (WDF) calculated from the Tank 40 dried sludge analysis results for SB8 is 1.9 ± 0.1. In general, the radionuclide concentration of the SB8 PS glass sample calculated using this WDF is in good agreement with the measured radionuclide content; The Product Consistency Test (PCT) results indicate that the SB8 PS glass meets the Waste Acceptance Product Specifications (WAPS) for durability, with normalized release rates for boron, lithium and sodium all at least two standard deviations lower than those of the Environmental Assessment (EA) glass; The average measured density of the SB8 PS glass is 2.72 g/cm 3 , consistent with previous PS samples; and, The average measured Fe 2+ /ΣFe ratio of the SB8 PS glass is 0.15, within the target range of 0.09- 0.33, and closely resembling the predicted REDOX value of 0.15.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Design of a Stable Heusler Alloy with Switchable Metal-to-Half-Metal Transition at Finite Temperature

We report the electronic structure and metallicity of Si-doped Mn2VGe Heusler alloys within the first-principles density-functional theory framework are discussed. Mn2VGe is found to assume two stable structures at (cubic) lattice constants of 5.7 and 6.05 Å, which are well-separated in energy and correspond to half-metallic (low-spin) and metallic (high-spin) phases, respectively. Substitution of Ge by Si reduces the energy difference between these two phases, which become nearly degenerate at an Si concentration of ≈3.125 at% at zero temperature. The analysis shows that the switching between the high- and low-spin phases for this composition can be triggered via a pressure of 2.8 GPa at 300 K. Si-doped Mn 2 VGe can thus provide an ultrafast, low power, cost-effective materials platform for spintronics applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing the meta-stability of oxide core/shell nanoparticle systems at atomic resolution

Hybrid nanoparticles allow exploiting the interplay of confinement, proximity between different materials and interfacial effects. However, to harness their properties an in-depth understanding of their (meta)stability and interfacial characteristics is crucial. This is especially the case of nanosystems based on functional oxides working under reducing conditions, which may severely impact their properties. Here, the in-situ electron-induced selective reduction of Mn 3 O 4 to MnO is studied in magnetic Fe 3 O 4 /Mn 3 O 4 and Mn 3 O 4 /Fe 3 O 4 core/shell nanoparticles by means of high-resolution scanning transmission electron microscopy combined with electron energy-loss spectroscopy. Such in-situ transformation allows mimicking the actual processes in operando environments. A multi-stage image analysis using geometric phase analysis combined with particle image velocity enables direct monitoring of the relationship between structure, chemical composition and strain relaxation during the Mn 3 O 4 reduction. In the case of Fe 3 O 4 /Mn 3 O 4 core/shell the transformation occurs smoothly without the formation of defects. However, for the inverse Mn 3 O 4 /Fe 3 O 4 core/shell configuration the electron beam-induced transformation occurs in different stages that include redox reactions and void formation followed by strain field relaxation via formation of defects. This study highlights the relevance of understanding the local dynamics responsible for changes in the particle composition in order to control stability and, ultimately, macroscopic functionality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗
DOE OSTI2022

An analysis of fluff formation in metallic fuel via data analyzes from EBR-II experiments and BISON fuel code modeling

During the operation of EBR-II, it was found that a highly porous structure (over 40% area fraction) formed at the top of several fuel columns. Previous work has shown that this structure, designated fluff in this paper, contains a significant fraction of fuel elements (e.g., U and Pu) which could potentially impact neutronics. This work aims in analyzing the formation mechanism of this microstructure so its impact can be incorporated into future metallic fuel modeling codes and algorithms. This paper details a preliminary examination into the formation mechanisms of fluff by performing qualitative and statistical analysis of EBR-II experimental data. Additionally, the operating conditions that have the greatest impact on fluff formation were determined based on this data set. Also, BISON fuel code simulations were used to help postulate potential fluff formation mechanisms. From this analysis it was found that the largest contributors to fluff formation were fuel burnup and composition, with fluff formation exhibiting a roughly linear positive correlation with increasing burnup and a negative correlation with increasing Pu content. It was also found that higher pin operating temperatures decreased fluff formation but only for U-10Zr fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗