Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “actuation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

High-Speed Experiments on Combustion-Powered Actuation for Dynamic Stall Suppression

This work documents high-speed wind tunnel experiments conducted on a pitching airfoil equipped with an array of combustion-powered actuators (COMPACT). The main objective of these experiments was to demonstrate the stall-suppression capability of COMPACT on a high-lift rotorcraft airfoil, the VR-12, at relevant Mach numbers. Through dynamic pressure measurements at the airfoil surface it was shown that COMPACT can positively affect the stall behavior of the VR-12 at Mach numbers up to 0.4. Static airfoil results demonstrated 25% and 50% increases in post-stall lift at Mach numbers of 0.4 and 0.3, respectively. Deep dynamic stall results showed cycle-averaged lift coefficient increases up to 11% at Mach 0.4. Furthermore, it was shown that these benefits could be achieved with relatively few pulses during down-stroke and with no need to pre-anticipate the stall event. The flow mechanisms responsible for stall suppression were investigated using particle image velocimetry.

Matalanis, Claude↗
NASA NTRS2016

Femtosecond Laser Tagging Characterization of a Sweeping Jet Actuator Operating in the Compressible Regime

A sweeping jet (SWJ) actuator operating over a range of nozzle pressure ratios (NPRs) was characterized with femtosecond laser electronic excitation tagging (FLEET), single hot-wire anemometry (HWA) and high-speed/phase-averaged schlieren. FLEET velocimetry was successfully demonstrated in a highly unsteady, oscillatory flow containing subsonic through supersonic velocities. Qualitative comparisons between FLEET and HWA (which measured mass flux since the flow was compressible) showed relatively good agreement in the external flow profiles. The spreading rate was found to vary from 0.5 to 1.2 depending on the pressure ratio. The precision of FLEET velocity measurements in the external flow field was poorer (is approximately equal to 25 m/s) than reported in a previous study due to the use of relatively low laser fluences, impacting the velocity fluctuation measurements. FLEET enabled velocity measurements inside the device and showed that choking likely occurred for NPR ≥ 2.0, and no internal shockwaves were present. Qualitative oxygen concentration measurements using FLEET were explored in an effort to gauge the jet's mixing with the ambient. The jet was shown to mix well within roughly four throat diameters and mix fully within roughly eight throat diameters. Schlieren provided visualization of the internal and external flow fields and showed that the qualitative structure of the internal flow does not vary with pressure ratio and the sweeping mechanism observed for incompressible NPRs also probably holds for compressible NPRs.

Peters, Christopher J.↗
NASA NTRS2016

Dynamic Stall Suppression Using Combustion-Powered Actuation (COMPACT)

Retreating blade stall is a well-known phenomenon that limits rotorcraft speed, maneuverability, and efficiency. Airfoil dynamic stall is a simpler problem, which demonstrates many of the same flow phenomena. Combustion Powered Actuation (COMPACT) is an active flow control technology, which at the outset of this work, had been shown to mitigate static and dynamic stall at low Mach numbers. The attributes of this technology suggested strong potential for success at higher Mach numbers, but such experiments had never been conducted. The work detailed in this report documents a 3-year effort focused on assessing the effectiveness of COMPACT for dynamic stall suppression at freestream conditions up to Mach 0.5. The work done has focused on implementing COMPACT on a high-lift rotorcraft airfoil: the VR-12. This selection was made in order to ensure that any measured benefits are over and above the capabilities of state-of-the-art high-lift rotorcraft airfoils. The detailed Computational Fluid Dynamics (CFD) simulations, wind-tunnel experiments, and system-level modeling conducted have shown the following: (1) COMPACT, in its current state of development, is capable of reducing the adverse effects of deep dynamic stall at Mach numbers up to 0.4; (2) The two-dimensional (2D) CFD results trend well compared to the experiments; and (3) Implementation of the CFD results into a system-level model suggest that significant rotor-level benefits are possible.

Matalanis, Claude G.↗
NASA NTRS2017

Linear Actuator System for the NASA Docking System

The Linear Actuator System (LAS) is a major sub-system within the NASA Docking System (NDS). The NDS Block 1 will be used on the Boeing Crew Space Transportation (CST-100) system to achieve docking with the International Space Station. Critical functions in the Soft Capture aspect of docking are performed by the LAS, which implements the Soft Impact Mating and Attenuation Concept (SIMAC). This paper describes the general function of the LAS, the system's key requirements and technical challenges, and the development and qualification approach for the system.

Dick, Brandon↗
NASA NTRS2017

Ball Screw Actuator Including a Compliant Ball Screw Stop

An actuator includes a ball nut, a ball screw, and a ball screw stop. The ball nut is adapted to receive an input torque and in response rotates and supplies a drive force. The ball screw extends through the ball nut and has a first end and a second end. The ball screw receives the drive force from the ball nut and in response selectively translates between a retract position and a extend position. The ball screw stop is mounted on the ball screw proximate the first end to translate therewith. The ball screw stop engages the ball nut when the ball screw is in the extend position, translates, with compliance, a predetermined distance toward the first end upon engaging the ball nut, and prevents further rotation of the ball screw upon translating the predetermined distance.

Wingett, Paul T.↗
NASA NTRS2017

Normally-Closed Zero-Leak Valve with Magnetostrictive Actuator

A non-pyrotechnic, normally-closed, zero-leak valve is a replacement for the pyrovalve used for both in-space and launch vehicle applications. The valve utilizes a magnetostrictive alloy for actuation, rather than pyrotechnic charges. The alloy, such as Terfenol-D, experiences magnetostriction, i.e. a gross elongation, when exposed to a magnetic field. This elongation fractures a parent metal seal, allowing fluid flow through the valve. The required magnetic field is generated by redundant coils that are isolated from the working fluid.

Ramspacher, Daniel J.↗
NASA NTRS2017

Linear Actuator System for the NASA Docking System

The Linear Actuator System (LAS) is a major sub-system within the NASA Docking System (NDS). The NDS Block 1 will be used on the Boeing Crew Space Transportation (CST-100) system to achieve docking with the International Space Station. Critical functions in the Soft Capture aspect of docking are performed by the LAS. This paper describes the general function of the LAS, the system's key requirements and technical challenges, and the development and qualification approach for the system.

Dick, Brandon N.↗
NASA NTRS2018

Propellant Flow Actuated Piezoelectric Igniter for Combustion Engines

A propellant flow actuated piezoelectric igniter device using one or more hammer balls retained by one or more magnets, or other retaining method, until sufficient fluid pressure is achieved in one or more charging chambers to release and accelerate the hammer ball, such that it impacts a piezoelectric crystal to produce an ignition spark. Certain preferred embodiments provide a means for repetitively capturing and releasing the hammer ball after it impacts one or more piezoelectric crystals, thereby oscillating and producing multiple, repetitive ignition sparks. Furthermore, an embodiment is presented for which oscillation of the hammer ball and repetitive impact to the piezoelectric crystal is maintained without the need for a magnet or other retaining mechanism to achieve this oscillating impact process.

Wollen, Mark A.↗
NASA NTRS2016

Preface of the 18th Electroactive Polymers Actuators and Devices

This SPIE’s Electroactive Polymers Actuators and Devices (EAPAD) Conference is the leading international forum for presenting the latest progress and holding discussions among the attendees regarding the capabilities, challenges and potential future directions. The conference this year was Chaired by Yoseph Bar-Cohen, JPL/Caltech, and Co-Chaired by Frédéric Vidal, University de Cergy-Pontoise (France) and it included 128 presentations.

Bar-Cohen, Yoseph↗
NASA NTRS2020

Subscale Indoor Trajectory Testing via Six DOF Tendon-Actuated Robot

The NASA Johnson Space Center (JSC) Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project is developing a large-scale six degree of freedom tendon-actuated robot (STAR). STAR is intended to reproduce lunar approach trajectories across subscale terrain in order to rapidly develop and test terrain relative and hazard relative navigation algorithms at low cost. NASA is interested in hosting external partners at the facility to enable them to advance their own algorithm development and testing and intends to activate the facility in Fall 2020. Contact us for more information.

Pedrotty, Samuel M.↗
NASA NTRS2001

Piezoelectrically actuated miniature peristaltic pump.

There is a range of NASA experiments, instruments and applications where miniature pumps are needed. To address such needs, a piezoelectrically actuated miniature pump is being developed. This pump employs a novel volume displacing mechanism using flexural traveling waves that acts peristaltically and eliminates the need for valves or physically moving parts. This pump is being developed for planetary instruments and space applications. Finite element model was developed using ANSYS for the purpose of prediction of the resonance frequency of the vibrating mode for the piezo-pump driving stator. The model allows determining simultaneously the mode shapes that are associated with the various resonance frequencies. This capability is essential for designing the pump size and geometry. To predict and optimize the pump efficiency that is determined by the volume of pumping chambers the model was modified to perform harmonic analysis.

Chang, Zensheu↗
NASA NTRS1997

Rotary Ultrasonic Motors Actuated by Traveling Flexural Waves

Ultrasonic rotary motors are being developed as acutators for miniature spacecraft insturments and subsystems. The technology that has emerged in commercial products requires rigorous analytical tools for effective design of such motors. An analytical model was developed to examine the excitation of flexural plate wave traveling in rotary piezoelectrically actuated motor.

Piezoelectric↗
NASA NTRSDate not supplied

Subscale Indoor Trajectory Testing Via Six DOF Tendon-Actuated Robot

The NASA Johnson Space Center (JSC) Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project has developed a large-scale six degree of freedom tendon-actuated robot (STAR). STAR is intended to reproduce lunar approach trajectories across subscale terrain in order to rapidly develop and test terrain relative and hazard relative navigation/detection algorithms at low cost. NASA is interested in hosting external partners at the facility to enable them to advance their own algorithm development and testing. Contact us for more information.

Samuel Mark Pedrotty↗
NASA NTRSDate not supplied

Spacecraft Operation Emulation Via Six DOF Tendon-Actuated Robot

NASA Johnson Space Center’s (JSC) Simulation, Emulation, Navigation, Sensors and STAR (SENSS) Laboratory has developed a large-scale six degree of freedom tendon-actuated robot (STAR) for emulation of spacecraft proximity operations and Entry, Descent, and Landing approach trajectories to aid in the rapid development and testing of a wide range of guidance, navigation, and control algorithms at low cost.

navigation↗