Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

The design, testing and evaluation of the MIT individual-blade-control system as applied to gust alleviation for helicopters

A type of active control for helicopters was designed and tested on a four foot diameter model rotor. A single blade was individually controlled in pitch in the rotating frame over a wide range of frequencies by electromechanical means. By utilizing a tip mounted accelerometer as a sensor in the feedback path, significant reductions in blade flapping response to gust were achieved at the gust excitation frequency as well as at super and subharmonics of rotor speed.

Mckillip, R. M., Jr.↗
NASA NTRS1989

Miniature multiple-function probe for OTV turbopump health monitoring

A miniature multifunction rotating machinery shaft displacement sensor designed for a turbopump health monitoring system is described. The sensor probe tip has three independent sensing electrodes running in a groove made in the shaft of the machine. One of these electrodes, situated at the tip of the sensor, measures the radial displacement of the shaft, while the two side electrodes measure the axial displacements of the sides of the groove. The displacement sensor is also used to measure speed, by providing a notch in the side of the groove facing one sensor electrode. Results obtained with experimental sensors demonstrated that multifunction capacitive sensing is practical and reduces instrumentation penetration into rotating machinery housings.

Bickford, R. L.↗
NASA NTRS1989

The design of a low Reynolds number RPV

This paper covers the ongoing design process for a long endurance Remotely Piloted Vehicle (RPV). The 45-pound RPV must operate in the 25-50 knot speed range at low altitudes. Specially designed low-Reynolds number airfoils were used for efficient aerodynamics. A wing of AR = 23 was selected which will give an estimated L/D(max) of 27. Wing tip feathers will be used to reduce the induced drag. A comparison between the computed aerodynamic predictions and wind tunnel results is given. The predicted handling quality and performance results are given.

Siddiqi, S.↗
NASA NTRS1991

Numerical, experimental, and theoretical study of convective instability of flows over pointed bodies at incidence

A study is conducted to investigate whether the behavior of the asymmetric mean flow observed on pointed bodies of revolution at incidence remains consistent with the presence of a convective instability of an original symmetric flow, even in the incidence range where virtually bistable behavior of the asymmetric flow is observed. By means of a retractable wire located near the tip, it is determined experimentally that for all angles of attack tested (30 to 60 degs), changing the size or location of the controlled disturbance results in a finite change in the asymmetric flow field, even to the extent of reversing the sign of the side force or becoming almost symmetric. The process is reversible; returning the wire to an original position likewise restores the corresponding flow field and mean side force. The effect of wire location (roll angle and distance from the tip) as well as angle of attack and flow conditions are evaluated experimentally by means of flow visualization and side-force measurements for a generic ogive-cylinder model in a low-speed wind tunnel. Evaluation of the results in the light of computational observations and theoretical considerations yields an affirmative answer to the question posed.

Degani, David↗
NASA NTRS2000

Method of Forming Micro-Sensor Thin-Film Anemometer

A device for measuring turbulence in high-speed flows is provided which includes a micro- sensor thin-film probe. The probe is formed from a single crystal of aluminum oxide having a 14 deg half-wedge shaped portion. The tip of the half-wedge is rounded and has a thin-film sensor attached along the stagnation line. The bottom surface of the half-wedge is tilted upward to relieve shock induced disturbances created by the curved tip of the half-wedge. The sensor is applied using a microphotolithography technique.

Sheplak, Mark↗
NASA NTRS1996

Micro-sensor thin-film anemometer

A device for measuring turbulence in high-speed flows is provided which includes a micro-sensor thin-film probe. The probe is formed from a single crystal of aluminum oxide having a 14.degree. half-wedge shaped portion. The tip of the half-wedge is rounded and has a thin-film sensor attached along the stagnation line. The bottom surface of the half-wedge is tilted upward to relieve shock induced disturbances created by the curved tip of the half-wedge. The sensor is applied using a microphotolithography technique.

Sheplak, Mark↗
NASA NTRS1995

Coupled Aerodynamic-Thermal-Structural (CATS) Analysis

Coupled Aerodynamic-Thermal-Structural (CATS) Analysis is a focused effort within the Numerical Propulsion System Simulation (NPSS) program to streamline multidisciplinary analysis of aeropropulsion components and assemblies. Multidisciplinary analysis of axial-flow compressor performance has been selected for the initial focus of this project. CATS will permit more accurate compressor system analysis by enabling users to include thermal and mechanical effects as an integral part of the aerodynamic analysis of the compressor primary flowpath. Thus, critical details, such as the variation of blade tip clearances and the deformation of the flowpath geometry, can be more accurately modeled and included in the aerodynamic analyses. The benefits of this coupled analysis capability are (1) performance and stall line predictions are improved by the inclusion of tip clearances and hot geometries, (2) design alternatives can be readily analyzed, and (3) higher fidelity analysis by researchers in various disciplines is possible. The goals for this project are a 10-percent improvement in stall margin predictions and a 2:1 speed-up in multidisciplinary analysis times. Working cooperatively with Pratt & Whitney, the Lewis CATS team defined the engineering processes and identified the software products necessary for streamlining these processes. The basic approach is to integrate the aerodynamic, thermal, and structural computational analyses by using data management and Non-Uniform Rational B-Splines (NURBS) based data mapping. Five software products have been defined for this task: (1) a primary flowpath data mapper, (2) a two-dimensional data mapper, (3) a database interface, (4) a blade structural pre- and post-processor, and (5) a computational fluid dynamics code for aerothermal analysis of the drum rotor. Thus far (1) a cooperative agreement has been established with Pratt & Whitney, (2) a Primary Flowpath Data Mapper has been prototyped and delivered to General Electric Aircraft Engines and Pratt & Whitney for evaluation, (3) a collaborative effort has been initiated with the National Institute of Standards and Testing to develop a Standard Data Access Interface, and (4) a blade tip clearance capability has been implemented into the Structural Airfoil Blade Engineering Routine (SABER) program. We plan to continue to develop the data mappers and data management tools. As progress is made, additional efforts will be made to apply these tools to propulsion system applications.

Source record↗
NASA NTRS1981

Hover tests of a model H-force rotor

The potential of using tip vanes at the ends of helicopter rotor blades to obtain a controllable H-force is considered. The addition of vanes placed perpendicular to the blade tips can be used to obtain an inplane force. By varying the angle of the vanes, a radial force can be created which can be controllable in azimuth position. Such a force could be used to provide translational motion of the rotor and aircraft without the requirement for rotor tilting. In addition, an H-force generated at high flight speed could be used as a propulsive force in a matter similar to a propeller. The force generated by the vanes could also affect the aircraft's stability characteristics. The H-force could also modify rotor performance in hovering since they could be thought to act as a virtual shroud. Tests were run with a model rotor which has a 6 foot diameter with a 3 inch chord blade. Test data are presented on the effects of various tip-vane configurations on the hovering figure of merit. The extreme sensitivity of the performance to vane arrangement is shown.

Velkoff, H. R.↗
NASA NTRS1983

An aeroacoustic model for high-speed, unsteady blade-vortex interaction

A three-dimensional aeroacoustic model is developed to predict the sound pulse radiated by the passage of a helicopter blade over a potential vortex. The linearized analysis assumes that either the blade-vortex separation is small or that the blade-tip Mach number is close to 1, or both, so that an acoustically noncompact situation exists. The three-dimensional blade loading due to blade-vortex interaction is constructed through a spanwise superposition of two-dimensional solutions with strength linearly increasing from hub to tip. Such a loading overestimates somewhat the strength of tip region dipoles in the acoustic calculation that follows. The final expression for the predicted far-field signature is obtained in closed form, and thus permits a relatively inexpensive calculation of the directivity of peak acoustic pressures in three dimensions.

Martinez, R.↗
NASA NTRS1974

An experimental investigation of leading-edge vortex augmentation by blowing

A wind tunnel test was conducted to determine the effects of over-the-wing blowing as a means of augmenting the leading-edge vortex flow of several pointed-tip, sharp-edged planforms. Arrow, delta, and diamond wings with leading-edge sweeps of 30 and 45 degrees were mounted on a body-of-revolution fuselage and tested in a low-speed wind tunnel at a Mach number of 0.2. Nozzle location data, pitch data, and flow-visualization pictures were obtained for a range of blowing rates. Results show pronounced increases in vortex lift due to the blowing.

Bradley, R. G.↗
NASA NTRS1978

Cold-air performance of a tip turbine designed to drive a lift fan. 3: Effect of simulated fan leakage on turbine performance

Performance data were obtained experimentally for a 0.4 linear scale version of the LF460 lift fan turbine for a range of scroll inlet total to diffuser exit static pressure ratios at design equivalent speed with simulated fan leakage air. Tests were conducted for full and partial admission operation with three separate combinations of rotor inlet and rotor exit leakage air. Data were compared to the results obtained from previous investigations in which no leakage air was present. Results are presented in terms of mass flow, torque, and efficiency.

Haas, J. E.↗
NASA NTRS1957

Experimental investigation of an axial-flow-compressor inlet stage operating at transonic relative inlet Mach numbers V : rotor blade-element performance at a reduced blade angle

At a corrected speed of 1100 feet per second, the low-blade-angle rotor operated with a relative inlet Mach number of 1.2, a diffusion factor of 0.65, and an axial velocity ratio of 0.71 in the tip region (11 percent of passage height away from the outer wall). The measured minimum-loss coefficient was 0.35, and this value falls above a previous correlation of rotor losses with diffusion factor. Through a comparison with data for three other rotors, the occurrence of high losses was related to a high suction-surface Mach number. These comparisons also indicated that axial velocity ratios between 0.73 and 1.10 have no independent effect on losses.

Schwenk, Francis C↗
NASA NTRS1994

Micro-sensor thin-film anemometer

A device for measuring turbulence in high-speed flows is provided which includes a micro-sensor thin-film probe. The probe is formed from a single crystal of aluminum oxide having a 14 deg half-wedge shaped portion. The tip of the half-wedge is rounded and has a thin-film sensor attached along the stagnation line. The bottom surface of the half-wedge is tilted upward to relieve shock induced disturbances created by the curved tip of the half-wedge. The sensor is applied using a microphotolithography technique.

Sheplak, Mark↗
NASA NTRS1961

Wind-Tunnel Investigation of the Effects of Wing Bodies, Fences, Flaps, and a Fuselage Addition on the Wing Buffet Response of a Transonic-Transport Model

The experimental wing buffet response of a transport-type airplane model with and without wing bodies, fences, flaps, and a fuselage addition has been investigated at Mach numbers from 0.20 to 1.03. The wing had NACA 64A-series airfoil sections inclined 5 degrees to the free-stream direction. The quarter-chord line of the wing was swept back 45 degrees, the aspect ratio was 7, the taper ratio was 0.3, and the thickness ratio varied from 0.115 at the root to 0.074 at the midsemispan and was constant from that station to the tip. The wing was twisted and cambered for a design lift coefficient of 0.3. The results of the investigation indicated that a marked reduction of buffet intensity and a delay of buffet onset at transonic speeds were achieved by the addition to the wing of special bodies designed to reduce shock-induced separation. The further addition of wing fences and wing trailing-edge flaps deflected 30 degrees increased the lift coefficients at which low-speed stall buffeting occurred. An addition to the fuselage near the upper forward portion produced no consistent change in the buffet characteristics.

Cornette, Elden S.↗
NASA NTRS2004

Assessment of Comprehensive Analysis Calculation of Airloads on Helicopter Rotors

Blade section normal force and pitching moment were investigated for six rotors operating at transition and high speeds: H-34 in flight and wind tunnel, SA 330 (research Puma), SA 349/2, UH-60A full-scale and BO-105 model (HART-I). The measured data from flight and wind tunnel tests were compared with calculations obtained using the comprehensive analysis CAMRAD II. The calculations were made using two free wake models: rolled-up and multiple-trailer with consolidation models. At transition speed, there is fair to good agreement for the blade section normal force between the test data and analysis for the H-34, research Puma, and SA 349/2 with the rolled-up wake. The calculated airloads differ significantly from the measurements for the UH-60A and BO-105. Better correlation is obtained for the UH-60A and BO-105 by using the multiple-trailer with consolidation wake model. In the high speed condition, the analysis shows generally good agreement with the research Puma flight data in both magnitude and phase. However, poor agreement is obtained for the other rotors examined. The analysis shows that the aerodynamic tip design (chord length and quarter chord location) of the Puma has an important influence on the phase correlation.

Yeo, Hyeonsoo↗
NASA NTRS2015

Novel Control Effectors for Truss Braced Wing

At cruise flight conditions very high aspect ratio/low sweep truss braced wings (TBW) may be subject to design requirements that distinguish them from more highly swept cantilevered wings. High aspect ratio, short chord length and relative thinness of the airfoil sections all contribute to relatively low wing torsional stiffness. This may lead to aeroelastic issues such as aileron reversal and low flutter margins. In order to counteract these issues, high aspect ratio/low sweep wings may need to carry additional high speed control effectors to operate when outboard ailerons are in reversal and/or must carry additional structural weight to enhance torsional stiffness. The novel control effector evaluated in this study is a variable sweep raked wing tip with an aileron control surface. Forward sweep of the tip allows the aileron to align closely with the torsional axis of the wing and operate in a conventional fashion. Aft sweep of the tip creates a large moment arm from the aileron to the wing torsional axis greatly enhancing aileron reversal. The novelty comes from using this enhanced and controllable aileron reversal effect to provide roll control authority by acting as a servo tab and providing roll control through intentional twist of the wing. In this case the reduced torsional stiffness of the wing becomes an advantage to be exploited. The study results show that the novel control effector concept does provide roll control as described, but only for a restricted class of TBW aircraft configurations. For the configuration studied (long range, dual aisle, Mach 0.85 cruise) the novel control effector provides significant benefits including up to 12% reduction in fuel burn.

White, Edward V.↗
NASA NTRS1977

Wind tunnel and ground static tests of a .094 scale powered model of a modified T-39 lift/cruise fan V/STOL research airplane

Ground static and wind tunnel test of a scale model modified T-39 airplane are reported. The configuration in the nose and replacement of the existing nacelles with tilting lift/cruise fans. The model was powered with three 14 cm diameter tip driven turbopowered simulators. Forces and moments were measured by an internal strain guage balance. Engine simulator thrust and mass flow were measured by calibrated pressure and temperature instrumentation mounted downstream of the fans. The low speed handling qualities and general aerodynamic characteristics of the modified T-39 were defined. Test variables include thrust level and thrust balance, forward speed, model pitch and sideslip angle at forward speeds, model pitch, roll, and ground height during static tests, lift/cruise fan tilt angle, flap and aileron deflection angle, and horizonal stabilizer angle. The effects of removing the landing gear, the lift/cruise fans, and the tail surfaces were also investigated.

Hunt, D.↗