Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEST PROGRAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Catalytic Site Requirements for N2O Decomposition on Cu-, Co-, and Fe-SSZ-13 Zeolites

N2O decomposition is investigated on Cu, Co and Fe-exchanged SSZ-13 zeolite catalysts at relatively low metal loadings. The catalysts are synthesized by solution ion exchange, and subjected to X-ray diffraction (XRD), temperature-programed-reduction by H2 (H2-TPR), temperature-programed-reaction of N2O (N2O-TPR) coupled with in-situ transmission FTIR, and finally steady-state flow reaction tests. At low N2O pressures (< 0.05 kPa), all catalysts display pseudo first-order kinetics. From Arrhenius analysis, Cu and Fe-SSZ-13 display very different apparent activation energies but similar pre-exponential factors, suggesting their similar reaction mechanisms. N2O decomposition follows a dual-site mechanism, occurring on dimeric M-O-M sites in these catalysts, and O2 is formed by the combination of two O ad-atoms from two vicinal metal sites. Under low N2O pressure (0.05 kPa) and first-order kinetic regime, the reaction is limited by N-O cleavage on bare metal active sites. In comparison to Cu-SSZ-13, the much higher N2O decomposition rate over Fe-SSZ-13 is attributed to the much lower activation barriers for the N-O cleavage step. N2O decomposition occurs on isolated Co2+ ions in Co-SSZ-13. The rate-limiting step is N-O cleavage on an O-occupied Co site in the low-pressure first order kinetic regime. This single-site mechanism leads to much higher pre-exponential factors as compared to the dual-site mechanism. This beneficial factor for reaction rate enhancement, however, is compromised by the much higher activation barriers over this catalyst.

Lin, Fan↗
DOE OSTI2021

A two-stage service restoration method for electric power distribution systems

Improving the reliability of power distribution systems is critically important for both utilities and customers. This calls for an efficient service restoration module within a distribution management system to support the implementation of self-healing smart grid networks. Although the emerging smart grid technologies, including distributed generators (DGs) and remote-controlled switches, enhance the self-healing capability and allow faster recovery, they still pose additional complexity to the service restoration problem, especially under cold load pickup (CLPU) conditions. Herein, a novel two-stage restoration framework is proposed to generate a restoration solutions with a sequence of control actions. The first stage generates a restoration plan that supports both the traditional service restoration using feeder reconfiguration and the grid-forming DG-assisted intentional islanding methods. The second stage generates an optimal sequence of switching operations to bring the outaged system quickly to the final restored configuration. The problem is formulated as a mixed-integer linear program that incorporates system connectivity, operating constraints, and the CLPU models. It is demonstrated that on using a multi-feeder test case, the proposed framework is effective in utilizing all available resources to quickly restore the service and generate an optimal sequence of switching actions to be used by the operator to reach the desired optimal configuration.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Document-Based Nuclear Archaeology

Deeper reductions in the nuclear arsenals will require better understanding of historic fissile material management and production. The concept of “nuclear archaeology” has been considered since the 1990s to provide the tools and methods to develop independent production estimates, primarily based on nuclear forensic techniques. Here, we propose to add a framework for reconstructing the history of a nuclear program that complements traditional nuclear archaeology techniques by examining the role of operating records to support such an effort. As a test case, we use the JEEP II reactor, a 2 MW civilian research reactor at Norway’s Institute for Energy Technology (IFE), in operation for more than fifty years, however, recently shut down permanently. We have collected, analyzed, and started to preserve the reactor’s operating records, which exist on both analog and digital media, and to simulate parts of its history using OpenMC/ONIX neutronics calculations. Here, a particular focus of this project has been on digital data curation and preservation to confirm and maintain the integrity, authenticity, and provenance of these records. In developing guidelines for best practices that conform to existing standards for long-term digital preservation and curation, we hope this project can help lay the basis for future nuclear archaeology efforts to support nuclear arms control and disarmament.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Liquid Argon Time Projection Chamber Trigger Development with MicroBooNE

The Micro Booster Neutrino Experiment (MicroBooNE) is a Liquid Argon Time Projection Chamber (LArTPC) neutrino detector at Fermilab that has been operating since 2015. It aims to perform v-Ar cross-section measurements, explore the low-energy excess reported by the MiniBooNE experiment and perform a combined search for sterile neutrino oscillations as part of three LArTPCs that make up the Short Baseline Neutrino (SBN) Program at Fermilab. Since MicroBooNE is currently in an R&D phase, it offers a unique opportunity for the implementation and testing of TPC-based triggers as R&D towards the Deep Underground Neutrino Experiment (DUNE). One of the technical challenges of DUNE that we aim to address with this study is that of efficient self-triggering of a LArTPC utilizing TPC signal information. This capability will enable searches for rare processes in DUNE, such as neutrino interactions from a potential galactic supernova burst. This talk will describe the MicroBooNE TPC readout system and ongoing R&D efforts to develop and demonstrate TPC-based triggering.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

LANL Contributions to pyiron: An integrated development environment for computational materials science

To support and accelerate the development of simulation protocols in atomistic modelling, we introduce an integrated development environment (IDE) for computational materials science called pyiron (http://pyiron.org). The pyiron IDE combines a web based source code editor, a job management system for build automation, and a hierarchical data management solution. The core components of the pyiron IDE are pyiron objects based on an abstract class, which links application structures such as atomistic structures, projects, jobs, simulation protocols and computing resources with persistent storage and an interactive user environment. The simulation protocols within the pyiron IDE are constructed using the Python programming language. To highlight key concepts of this tool as well as to demonstrate its ability to simplify the implementation and testing of simulation protocols we discuss two applications. In these examples we show how pyiron supports the whole life cycle of a typical simulation, seamlessly combines ab initio with empirical potential calculations, and how complex feedback loops can be implemented. While originally developed with focus on ab initio thermodynamics simulations, the concepts and implementation of pyiron are general thus allowing to employ it for a wide range of simulation topics.

Janssen, Jan↗
DOE OSTI2022

A tailored fast thioacidolysis method incorporating multi-reaction monitoring mode of GC-MS for higher sensitivity on lignin monomer quantification

Abstract Thioacidolysis is widely used for lignin structural characterization by cleaving β-aryl ethers to release syringyl (S), guaiacyl (G), and p -hydroxyphenyl (H) monomers followed by GC analysis. However, the traditional thioacidolysis method requires tedious extraction steps with chlorinated solvent underlying harmful to health, limiting its efficiency and application. Herein, an improved thioacidolysis method with high sensitivity for the quantitation of lignin-derived monomers was developed. The improved protocol used a quick, streamlined procedure to recover the monomeric products using ethyl acetate as extracting solvent and MS detector in multi-reaction monitoring mode to enhance its ability to detect extremely low concentration (0.1 ppb with signal-to-noise higher than 2) of monomeric products. Additionally, a fast GC program was established to speed up the GC quantitation. Several representative lignocellulose samples, including gymnosperm, angiosperm, and poaceae, were used to test this tailored method. The results demonstrated that the ratios of lignin monomer compositions determined by this method were consistent with that of traditional procedure despite the slightly higher monomer yields measured. More importantly, this method uses non-chlorinated solvent for microscale extraction and requires no evaporation step for workup, which is a green and efficient way for the quantification of lignin monomer compositions.

Forestry↗
DOE OSTI2021

Microseismic at HFTS2: A Story of Three Stimulated Wells

A microseismic data set was acquired at Hydraulic Fracturing Test Site 2 (HFTS2) in the Delaware Basin (Texas, USA) by the HFTS2 consortium as a part of data-collection program designed to help maximize the efficiency of hydraulic fracturing, understand the impacts of nearby depleted zones, and increase the production of hydrocarbons. Advanced methods of microseismic monitoring applied at HFTS2 include 1) native synchronization of five monitor arrays, 2) real-time location of microseismic events, 3) joint event hypocenter/ velocity-model inversion that locates microseismic events simultaneously with constructing azimuthally anisotropic velocity models, 4) high-resolution reservoir imaging, utilizing microseismic events as downhole sources. HFTS2 microseismic data set illustrated the influence of geologic complexity, variations in treatment designs, and the presence of parent wells on the efficiency of hydraulic fracturing. Three Wolfcamp wells, Boxwood 1H, 2H, and 4H, were stimulated sequentially, exhibiting very different patterns of microseismicity. When the Boxwood 1H well is stimulated, its toe stages quickly reacted to the presence of depleted Bitterroot section to the east of the Boxwood pad, extending microseismic events over 3,000 ft to the east. This behavior changes dramatically after the treatment passes the Bitterroot section at the toe, and the heel stages in 1H showed tight microseismic grouping around the stimulated well, indicative of treatment of virgin reservoir rock. The Boxwood 2H demonstrates this same pattern of behavior between the toe and heel stages of the well, suggesting that the depleted Bitterroot section remains easier to refracture than adjacent non-depleted rock. Microseismic activity associated with Boxwood 4H treatment is distinctly different from those in Boxwood wells 1H and 2H. The events generated during stimulation of 4H are hardly influenced by the depleted Bitterroot section and fill the space between the previously stimulated 1H and 2H wells. Altogether, microseismic patterns suggest that treatment fluids tend to find the weakest passages through geologic formations, and the relative well positions and treatment sequence have a significant impact on fracture geometry, as indicated by microseismic event locations.

58 GEOSCIENCES↗
DOE OSTI2025

Unified differentiable digital twin for the IOTA/FAST facility

As the design complexity of modern accelerators grows, there is more interest in using advanced simulations that have fast execution time or produce insights about accelerator state. One notable example of additional information are gradients of physical observables with respect to design parameters produced by differentiable simulations. The IOTA/FAST facility has recently begun a program to implement and experimentally validate a unified start-to-end differentiable digital twin to serve as a virtual accelerator test stand, allowing for rapid prototyping of new software and experiments with minimal beam time costs. In this contribution we will discuss our plans and progress. Specifically, we will cover the selection and benchmarking of both physics and ML codes, the development of generic interfaces between device models and surrogate or physics-based sections, and the export of the parameters through either a deterministic event loop or a fully asynchronous EPICS soft input/output controller. We will also discuss challenges in model calibration and uncertainty quantification, as well as future plans to support larger proton accelerators like PIPII and Booster.

Kuklev, Nikita [Fermilab]↗
DOE OSTI2021

NDT System for Metal Components in Concrete Structures

The goal of this SBIR program is to develop new NDT technology based on the innovative use of magnetic sensors designed specifically for ECT (Eddy Current Testing) of steel reinforcements in concrete structures. The Phase IIA goal is to expand the R&D accomplished in Phase II, such that the probe system is more capable, and the inspection system is more flexible.

42 ENGINEERING↗
DOE OSTI2021

Retrospective Analysis of Backwater Habitat Availability Using Remote Sensing

Low-velocity channel-margin habitats serve as important nursery habitats for the endangered Colorado pikeminnow (Ptychocheilus lucius) in the middle Green River between Jensen and Ouray, Utah. These habitats, known as backwaters, are associated with emergent sandbars, and are shaped and reformed annually by peak flows. Our recent knowledge about backwater characteristics and dynamics that is summarized in the synthesis report (Grippo et al. 2015) was based on detailed annual survey data from a relatively small sample of backwaters that were collected from 2003 to 2014 and reach-wide evaluations of backwater surface area based on manual interpretation of aerial and satellite imagery. Methods that bridge the gap between the detailed surveys from a small number of backwaters and the reach-wide assessment of their surface area would enable an assessment of the availability of backwater habitats that meet the minimum depth requirements for suitable habitat for Colorado pikeminnow. In 2015 Argonne National Laboratory (Argonne) tested three regression models—linear, multiple, and partial least square (PLS) regression models—for estimating backwater depth using National Agriculture Imagery Program (NAIP) imagery collected in July 2006 that covered the Jensen-Ouray reach of the Green River (Hamada and LaGory 2016). The results suggested that a PLS regression model showed high correlation with the reference depth (R 2 = 0.69) and had the most unbiased and consistent estimate of backwater depth. The results also indicated that the PLS model would provide reasonable estimates of the amount of habitat providing a minimum suitable depth of 30 cm for young-of-the-year Colorado pikeminnow, even though absolute depth estimates may be uncertain for backwater areas deeper than approximately 40 cm. The study also provided insights regarding the amount and the selection of calibration and validation (cal-val) data needed for improving the accuracy of depth prediction.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Closure Monitoring Report for Corrective Action Unit 97: Yucca Flat/Climax Mine, Underground Test Area, Nevada National Security Site, Nevada (Rev.1)

This report presents the results of monitoring conducted for water quality, water levels, and institutional controls in FY 2020 by DOE/EM Nevada Program UGTA Activity at CAU 97, Yucca Flat/Climax Mine at the Nevada National Security Site. This report also presents analytical laboratory results (including results of quality assurance/quality control samples, such as field duplicates); and verification of use restrictions, institutional controls, and water use.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Experimental Capabilities to Support Design, Development and Demonstration of Microreactors

This work provides a summary of selected experimental capabilities being developed to support non-nuclear demonstration of microreactors under the U.S. Department of Energy’s (DOE’s) Microreactor Program. Major capabilities include the single primary heat extraction and removal emulator (SPHERE) and the microreactor agile non-nuclear experimental test bed (MAGNET). The SPHERE facility allows for controlled testing of the steady-state and transient heat rejection capabilities of a single heat pipe using electrical heaters that simulate nuclear heating. The facility is capable of monitoring axial temperature profiles along the heat pipe and surrounding test articles during startup, steady-state operation, and transients. Instrumentation includes non-contact infrared thermal imaging, surface thermocouples, spatially distributed fiber-optic temperature and strain sensors, electrical power meters, and a water-cooled, gas gap calorimeter for quantifying heat rejection from the heat pipe. The facility can be operated under both vacuum and inert-gas conditions.

42 ENGINEERING↗
DOE OSTI2025

Tantalum Experiments in Fully-Reflected Water-Moderated Triangular-Pitched U(6.90)O 2 Fuel Rod Lattices (1.02 cm Pitch)

The United States (US) Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories (SNL). The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5 % 235 U. The 7uPCX assembly is a water moderated and — reflected array of aluminum-clad U(6.90 %)O 2 fuel rods. Other critical experiments performed in the 7uPCX assembly are documented in LEU-COMP-THERM-078, LEU-COMP-THERM-080, LEU-COMP-THERM 096, LEU- COMP-THERM-097, LEU-COMP-THERM-101, LEU-COMP-THERM-102, and LEU-COMP-THERM-111. Applied interests in neutron-absorbing elements at epithermal and intermediate neutron energy ranges at DOE’s Hanford Site and Savannah River Site were identified through DOE Office of Environmental Management (EM) workshops and needs surveys performed in conjunction with the National Nuclear Security Administration/Nuclear Criticality Safety Program. In response, a team lead by Oak Ridge National Laboratory (ORNL) performed a study evaluating the use of 7uPCX for testing the epithermal cross sections of materials at SNL. This marked the inception of the set of experiments described here. The purpose of these experiments was to measure the effects of tantalum in nearly-critical systems. The tantalum was introduced into the fuel arrays as experiment rods within a central test region. The central test region was designed to target the epithermal neutron energy range by providing a dry cylindrical cavity constructed of aluminum and lined with 0.04 in (0.1016 cm) thick cadmium sheet. The central test region has an outer diameter of 3.75 in (9.525 cm) length of 31 in (78.74 cm) and can hold 85 tantalum rods nominally 0.25 in (0.635 cm) outside diameter and 31.25 in (79.375 cm) long. The critical experiments were done using a set of triangular-pitched grid plates fabricated for these experiments. The grid plate set accommodated a fuel array of a total of 2016 fuel rod positions on a pitch of 0.4 in (1.016 cm) in a series of 21 hexagonal rings positioned around the central test region. The fuel used in these experiments was fabricated using unirradiated 6.90 % enriched UO 2 fuel pellets from fuel elements designed to be used in the internal nuclear superheater section of the Pathfinder boiling water reactor operated in South Dakota by the Northern States Power Company in the 1960s. The fuel elements were obtained from The Pennsylvania State University where they had been stored for many years. The fuel pellets in those fuel elements were removed from the original Incoloy cladding and reclad in 3003 aluminum tubes and end caps for use in the experiments reported here. The eight cases in this experiment series were performed in 2024 in the Sandia Critical Experiments (SCX) at the Sandia Pulsed Reactor Facility by varying the number of fuel rods in the critical assembly. The personnel involved in conducting these experiments included David Ames, Elijah Lutz, Beth Hanson, Patrick Ward, Jason Soares, and Augie Chapa from SNL, as well as Mathieu Dupont and B.J. Marshall from ORNL. Case 1 had no tantalum experiment rods. Case 2 had seven tantalum rods in the center of the central test region. Case 3 had 18 tantalum rods in the third hexagonal ring of the central test region. Case 4 had 19 tantalum rods in the center of the central test region. Case 5 had 30 tantalum rods in the outer most positions of the central test region. Case 6 had 37 tantalum rods in the center of the central test region. Case 7 had 61 tantalum rods in the center of the central test region. Case 8 had 85 tantalum rods filling all positions in the central test region. All eight critical experiments are judged to be acceptable as benchmark experiments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Ring Pull Strain Analysis Version 1.1

This report details an analysis package, Ring Pull Strain Analysis (RPSA), that can be used to present and quantify digital image correlation (DIC) data as it relates to a gaugeless ring pull test. Gaugeless ring pull is a testing technique for mechanical testing of small annular samples, usually cut from a thin-walled tube. DIC data is often necessary for this kind of test because bending moments present on the ring cause a non-uniform strain distribution and localized measurements are necessary. In addition, the annular geometry of a ring lends itself to a polar representation, which is not present with typical DIC analysis methods. RPSA was made to calculate and plot the polar representation of strain from standard pre-processed DIC data of a gaugeless ring pull test. Further analysis can be done on ring pull including a quasi-uniaxial tensile analysis and coating analysis, which are also performed by RPSA. In addition, due to the universality of DIC plotting and ring pull test analysis, RPSA can accommodate a wide variety of tests, though it is tailored for ring pull testing. This report details how RPSA works, including the theory, assumptions, and logic behind the calculations and the structure of the program.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi-Site Observational Study to Assess Biomarkers for Susceptibility or Resilience to Chronic Pain: The Acute to Chronic Pain Signatures (A2CPS) Study Protocol

Chronic pain has become a global health problem contributing to years lived with disability and reduced quality of life. Advances in the clinical management of chronic pain have been limited due to incomplete understanding of the multiple risk factors and molecular mechanisms that contribute to the development of chronic pain. The Acute to Chronic Pain Signatures (A2CPS) Program aims to characterize the predictive nature of biomarkers (brain imaging, high-throughput molecular screening techniques, or “omics,” quantitative sensory testing, patient-reported outcome assessments and functional assessments) to identify individuals who will develop chronic pain following surgical intervention. The A2CPS is a multisite observational study investigating biomarkers and collective biosignatures (a combination of several individual biomarkers) that predict susceptibility or resilience to the development of chronic pain following knee arthroplasty and thoracic surgery. This manuscript provides an overview of data collection methods and procedures designed to standardize data collection across multiple clinical sites and institutions. Pain-related biomarkers are evaluated before surgery and up to 3 months after surgery for use as predictors of patient reported outcomes 6 months after surgery. The dataset from this prospective observational study will be available for researchers internal and external to the A2CPS Consortium to advance understanding of the transition from acute to chronic postsurgical pain.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Comparing the Performance of Julia on CPUs versus GPUs and Julia-MPI versus Fortran-MPI: a case study with MPAS-Ocean (Version 7.1)

Abstract. Some programming languages are easy to develop at the cost of slow execution, while others are fast at runtime but much more difficult to write. Julia is a programming language that aims to be the best of both worlds – a development and production language at the same time. To test Julia's utility in scientific high-performance computing (HPC), we built an unstructured-mesh shallow water model in Julia and compared it against an established Fortran-MPI ocean model, the Model for Prediction Across Scales–Ocean (MPAS-Ocean), as well as a Python shallow water code. Three versions of the Julia shallow water code were created: for single-core CPU, graphics processing unit (GPU), and Message Passing Interface (MPI) CPU clusters. Comparing identical simulations revealed that our first version of the Julia model was 13 times faster than Python using NumPy, where both used an unthreaded single-core CPU. Further Julia optimizations, including static typing and removing implicit memory allocations, provided an additional 10–20× speed-up of the single-core CPU Julia model. The GPU-accelerated Julia code was almost identical in terms of performance to the MPI parallelized code on 64 processes, an unexpected result for such different architectures. Parallelized Julia-MPI performance was identical to Fortran-MPI MPAS-Ocean for low processor counts and ranges from 2× faster to 2× slower for higher processor counts. Our experience is that Julia development is fast and convenient for prototyping but that Julia requires further investment and expertise to be competitive with compiled codes. We provide advice on Julia code optimization for HPC systems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Advanced control sequences and FDD technology. Just shiny objects, or ready for scale?

Innovations in commercial building control sequences (ASHRAE guideline 36) and fault detection and diagnostics (FDD) technology have the potential to transform existing building operational efficiency by realizing whole-building level savings on the order of 15% and higher. However, several technical and market barriers related to up-front estimation of achievable savings, verifying implementation, and ensuring persistence are slowing down their adoption as a core offering through diverse owner-funded initiatives and rate-payer funded programs. This paper describes a suite of solutions to overcome these barriers to program delivery of advanced HVAC controls integrated with FDD energy management and information system (EMIS) technology. First, the Guideline 36 conformance test offers an automated method to confirm correct sequence implementation by the manufacturer, before field deployment. A successful test of a controller was conducted using a new manufacturer-independent hardware-in-the-loop testbed demonstrating the viability and scalability of this approach. Second, the Guideline 36 energy savings calculator uses modeling paired with high-level user inputs to estimate building-specific savings potential, target cost effective implementation and minimize uncertainty. Initial results indicate the baseline control sequences significantly impact energy savings, however, as much as 50% savings may be possible for the worst-case baseline scenario. Third, a functional specification provides minimum recommended EMIS-FDD capabilities, and best practices to integrate the technology into organizational practice and ensure that advanced control sequences provide persistent savings.

Pritoni, Marco↗