Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Sim”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Electrodeposition of ZnO Nanorods in the Presence of Metal Ions

We report on structural and optical changes induced by impurity incorporation in ZnO nanorods grown via electrodeposition. We find the lattice parameters of the hexagonal ZnO rods to be larger than in defect-free single-crystalline ZnO. SIMS measurements indicate impurity incorporation and doping in the bulk of the nanorods. The impurity content correlates with changes in the electroluminescence spectra. The maximum of the defect luminescence band around 600 nm shifts towards longer wavelengths with metal incorporation. Aluminum incorporation leads to a narrow luminescence band close by the bandgap of ZnO around 390 nm.

Environmental Molecular Sciences Laboratory↗

Comparison of Computed Tomography Scout Based Reference Point Localization to Conventional Film and Axial Computed Tomography

Identification of source positions after implantation is an important step in brachytherapy planning. Reconstruction is traditionally performed from films taken by conventional simulators, but these are gradually being replaced in the clinic by computed tomography (CT) simulators. The present study explored the use of a scout image-based reconstruction algorithm that replaces the use of traditional film, while exhibiting low sensitivity to metal-induced artifacts that can appear in 3D CT methods. In addition, the accuracy of an in-house graphical software implementation of scout-based reconstruction was compared with seed location reconstructions for 2 phantoms by conventional simulator and CT measurements. One phantom was constructed using a planar fixed grid of 1.5-mm diameter ball bearings (BBs) with 40-mm spacing. The second was a Fletcher-Suit applicator embedded in Styrofoam (Dow Chemical Co., Midland, MI) with one 3.2-mm-diameter BB inserted into each of 6 surrounding holes. Conventional simulator, kilovoltage CT (kVCT), megavoltage CT, and scout-based methods were evaluated by their ability to calculate the distance between seeds (40 mm for the fixed grid, 30-120 mm in Fletcher-Suit). All methods were able to reconstruct the fixed grid distances with an average deviation of <1%. The worst single deviations (approximately 6%) were exhibited in the 2 volumetric CT methods. In the Fletcher-Suit phantom, the intermodality agreement was within approximately 3%, with the conventional sim measuring marginally larger distances, with kVCT the smallest. All of the established reconstruction methods exhibited similar abilities to detect the distances between BBs. The 3D CT-based methods, with lower axial resolution, showed more variation, particularly with the smaller BBs. With a software implementation, scout-based reconstruction is an appealing approach because it simplifies data acquisition over film-based reconstruction without requiring any specialized equipment and does not carry risk of misreads caused by artifacts.

61 RADIATION PROTECTION AND DOSIMETRY↗

Subsurface Examination of a Foliar Biofilm Using Scanning Electron- and Focused-Ion-Beam Microscopy

The dual beam scanning electron microscope, equipped with both a focused ion- and scanning electron- beam (FIB SEM) is a novel tool for the exploration of the subsurface structure of biological tissues. The FIB can remove a predetermined amount of material from a selected site to allow for subsurface exploration and when coupled with SEM or scanning ion- beam microscopy (SIM) could be suitable to examine the subsurface structure of bacterial biofilms on the leaf surface. The suitability of chemical and cryofixation was examined for use with the FIB SEM to examine bacterial biofilms on leaf surfaces. The biological control agent, Burkholderia pyroccinia FP62, that rapidly colonizes the leaf surface and forms biofilms, was inoculated onto geranium leaves and incubated in a greenhouse for 7 or 14 days. Cryofixation was not suitable for examination of leaf biofilms because it created a frozen layer over the leaf surface that cracked when exposed to the electron beam and the protective cap required for FIB milling could not be accurately deposited. With chemically fixed samples, it was possible to precisely FIB mill a single cross section (5 µm) or sequential cross sections from a single site without any damage to the surrounding surface. Biofilms, 7 days post-inoculation (DPI), were composed of 2 to 5 bacterial cell layers while biofilms 14 DPI ranged from 5 to greater than 30 cell layers. Empty spaces between bacteria cells in the subsurface structure were observed in biofilms 7- and 14-DPI. Sequential cross sections inferred that the empty spaces were often continuous between FP62 cells and could possibly make up a network of channels throughout the biofilm. FIB SEM was a useful tool to observe the subsurface composition of a foliar biofilm.

54 ENVIRONMENTAL SCIENCES↗

The lead-glass electromagnetic calorimeters for the magnetic spectrometers in Hall C at Jefferson Lab

The electromagnetic calorimeters of the various magnetic spectrometers in Hall C at Jefferson Lab are presented. For the existing HMS and SOS spectrometers design considerations, relevant construction information, and comparisons of simulated and experimental results are included. The energy resolution of the HMS and SOS calorimeters is better than $\sigma/E \sim 6%/\sqrt E $, and pion/electron ($\pi/e$) separation of about 100:1 has been achieved in energy range 1 -- 5 GeV. Good agreement has been observed between the experimental and simulated energy resolutions, but simulations systematically exceed experimentally determined $\pi^-$ suppression factors by close to a factor of two. For the SHMS spectrometer presently under construction details on the design and accompanying GEANT4 simulation efforts are given. The anticipated performance of the new calorimeter is predicted over the full momentum range of the SHMS. Good electron/hadron separation is anticipated by combining the energy deposited in an initial (preshower) calorimeter layer with the total energy deposited in the calorimeter.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The CLAS12 Micromegas Vertex Tracker

The Micromegas Vertex Tracker was designed to improve upon the tracking capabilities of the baseline design of the CLAS12 spectrometer in Hall~B at Jefferson Laboratory. A Barrel Micromegas Tracker made with six concentric cylinders, each made of three 120$^\circ$-sector tiles, surrounds the Silicon Vertex Tracker, and a Forward Micromegas Tracker composed of 6 disks is placed 30~cm downstream of the liquid-hydrogen target. Both trackers sit in a 5~T solenoid magnetic field. All Micromegas elements are based on resistive technology to withstand luminosities up to $10^{35}$~cm$^{-2}$s$^{-1}$, as well as on bulk technology to enforce gain uniformity and mechanical robustness. Due to the high magnetic field, dedicated electronics have been designed and displaced $\sim$2~m away from the detectors. The electronics readout is based on the DREAM ASICs that allow sustained operation up to 20~kHz trigger rate at the maximum luminosity.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Single electron–hole pair sensitive silicon detector with surface event discrimination

Here, we demonstrate single electron-hole pair resolution in a single-sided, contact-free 1 cm$^2$ by 1 mm thick Si crystal operated at 48 mK, with a baseline energy resolution of 3 eV. This crystal can be operated at voltages in excess of $\pm50$ V, resulting in a measured charge resolution of 0.06 electron-hole pairs. The high aluminum coverage ($\sim$70%) of this device allows for the discrimination of surface events and separation of events occurring near the center of the detector from those near the edge. We use this discrimination ability to show that dark events seen in previous detectors of a similar design are likely dominated by charge leakage along the side wall of the device. We saw only a small reduction in dark event rate with this biasing scheme, further suggesting that sidewall and edge-dominated processes are responsible for the majority of these events.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Plasma exposures of a high-conductivity graphitic foam for plasma facing components

The plasma-surface interactions from samples of high-conductivity graphitic foam biased to 120 V and placed in 6–8 eV deuterium plasmas with densities as high as 10 19 m -3 were investigated at the PSI-2 linear plasma device in Jülich. Graphitic foam-plasma interactions were also studied at the Wendelstein 7-X (W7-X) stellarator in Greifswald by exposure to hydrogen and helium plasmas using the Jülich multi-purpose manipulator. The purpose was to explore the possibility of using the material in a plasma facing component, and initial results were encouraging. In W7-X, no measurable erosion or cracking was observed. The PSI-2 samples received a deuterium fluence of 5 × 10 25 m -2 resulting in an average erosion of 43 µm or about 5 mg per sample. Residual gas analysis (RGA) data were acquired to monitor sample outgassing. Laser-induced Breakdown Spectroscopy (LIBS) was used to measure deuterium retention in the porous foam. After exposure, the surfaces were characterized with scanning electron microscopy, energy dispersive x-ray analysis and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The graphitic foam has a thermal conductivity as high as 287 W/mK and is considered as a replacement to more exotic carbon fiber composites such as SepCarb NB31 or isotropic graphites like ATJ that are no longer produced but used in present-day tokamak experiments. Actively cooled monoblocks were made from the foam and underwent extensive materials characterization including infrared response studies at Oak Ridge National Laboratory. This material is under consideration for the proposed actively-cooled W7-X divertor scraper element.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Exploration of Sn 70 Li 30 alloy as possible material for flowing liquid metal plasma facing components

As an advanced alternative to solid materials, Liquid Metals (LM) may offer more resilient and feasible Plasma Facing Components (PFCs). Particularly, regarding the unavoidable material erosion/degradation produced by particle/heat fluxes in future fusion devices where much longer duty cycles are expected. Furthermore, configurations that propose a flowing LM surface can add the advantage of a continuously fresh and clean layer facing the plasma. Although lithium is the most widely tested option, tin-lithium (SnLi) alloys have been proposed to attempt to combine the positive characteristics of both pure elements and ameliorate the specific issues of lithium. In this work, the potential use of Sn70Li30 alloy in such flowing concepts has been explored by addressing several preliminary and mandatory aspects for its utilization. Key issues such as wettability and compatibility of the alloy with relevant substrates have been studied in a multidisciplinary approach. The data obtained from deposited liquid tin-lithium droplets indicates approximate wetting temperatures of 360 °C, 390 °C and 405 °C for the fresh alloy on 316 stainless steel, molybdenum, and tungsten, respectively. However, the alloy contamination appeared to strongly affect the wetting characteristics of materials, increasing their wetting temperature by ~130 °C in the worst observed cases. Interestingly, in some instances, the instability of the liquid alloy surface was observed in the form of sudden gaseous ejection. The deposited droplets were posteriorly characterized in terms of absolute composition and depth profile by Inductively Coupled PlasmaOptical Emission Spectroscopy (ICP-OES) and Secondary Ion Mass Spectrometry (SIMS-ToF). Additionally, the nature and composition of the boundaries between the substrates and alloy microparticles was investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), and 3D Laser microscopy. The overall results of this post-mortem characterization revealed that first signs of corrosion induced by both alloy elements (lithium-chromium association and iron-tin intermetallic mixing) were present on 316 stainless steel after short exposures (≤3 h) at temperatures lower than 550 °C. Conversely, molybdenum and tungsten showed good compatibility with the alloy in equivalent conditions. The global implications of these results are finally addressed, focusing on the future perspectives and the more viable scenarios for the eventual utilization of these alloys in flowing liquid metal configurations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Testing of spark plasma sintered porous tungsten under neon glow discharge cleaning conditions in LTX-β

This paper demonstrates that tungsten (W) based powder reconstituted Plasma Facing Components (PFCs) can be treated in situ in a fusion reactor to remove W oxide and carbon (C) contamination. Doing so should ease the challenge of using these materials in a Capillary Porous System (CPS) with lithium (Li) by enabling better wetting and less contamination of the Li by the underlying CPS. Most powder reconstituted materials including 3D printed and sintered PFCs suffer from a high surface contamination from oxides and surface C, which complicates their use with liquid Li, a primary PFC candidate. Spark plasma sintered porous W samples were fabricated to be used as a CPS with liquid Li. The samples were characterized in terms of morphology and surface chemistry. Analysis confirms a high C and oxygen (O) contamination. We present the results of exposing this type of CPS to Glow Discharge Cleaning (GDC) cycles in the Lithium Tokamak Experiment-β (LTX-β). The sample was exposed to neon (Ne) GDC in the midplane of the low-field side of LTX-β and analyzed in vacuo with Temperature Programmed Desorption (TPD) and Secondary Ion Mass Spectrometry (SIMS) to investigate the effects the Ne GDC had on the chemical composition of the sample. The combination of Ne GDC with rapid heating as done in TPD was successful in reducing the W oxides and removing the C contamination.

Capillary porous system↗

Effects of Phosphorous-doping and High Temperature Annealing on CVD grown 3C-SiC

The integrity and property behavior of the SiC layer of the Tri-isotropic (TRISO) coated particle (CP) for high temperature reactors (HTR) are very important as the SiC layer is the main barrier for gaseous and metallic fission product release. This study describes the work done on un-irradiated SiC samples prepared with varying phosphorus levels to simulate the presence of phosphorus due to transmutation. 30Si transmutes to phosphorous (31P) and other transmutation products during irradiation, which may affect the integrity of the SiC layer. The P-doping levels of the SiC samples used in this study cover the range from 1.1x1015 to 1.2x1019 at/cm3 and are therefore relevant to the PBMR operating conditions. Annealing from 1000 C to 2100 C was performed to study the possible changes in nanostructures and various properties due to temperature. Characterization results by X-ray diffraction (XRD), secondary ion mass spectrometry (SIMS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM), are reported in this article. As grain boundary diffusion is identified as a possible mechanism by which 110mAg, one of the fission activation products, might be released through intact SiC layer, grain size measurements is also included in this study. Temperature is evidently one of the factors/parameters amongst others known to influence the grain size of SiC and therefore it is important to investigate the effect of high temperature annealing on the SiC grain size. The ASTM E112 method as well as electron back scatter diffraction (EBSD) was used to determine the grain size of various commercial SiC samples and the SiC layer in experimental PBMR Coated Particles (CPs) after annealing at temperatures ranging from 1600 C to 2100 C. The HRTEM micrograph of the decomposition of SiC at 2100 C are shown and discussed. Nanotubes were not identified during the TEM and HRTEM analysis although graphitic structures were identified. The preliminary conclusion reached is that the P-content at these experimental levels (1.1x1015 - 1.2x1019 atom/cm3) does not have a significant influence on the nanostructure of SiC at high temperatures without irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Natural top quark condensation (a redux)

The Nambu--Jona-Lasinio (NJL) model involves a pointlike 4-fermion interaction. While it gives a useful description of chiral dynamics (mainly in QCD), it nonetheless omits the crucially important internal wave-function of a two-body bound state, $\phi(r)$. This becomes significant near critical coupling where $\phi(r)$ extends to large distance, leading to dilution and suppression of induced couplings $\propto \phi(0)$, such as the Yukawa and quartic couplings, as well as reduced fine-tuning of a hierarchy. In top quark condensation, where the BEH boson is a $\bar{t}t$ bound state and we have a UV completion such as topcolor, we must go beyond the NJL model and include effects of $\phi(r)$. We provide a formulation of this for the Brout-Englert-Higgs boson, and find that it leads to an extended $\phi(r)$, a significantly reduced and natural composite scale of $M_0 \sim 6$ TeV, a successful prediction for the quartic coupling, $\lambda$, and fine tuning that is reduced to a few percent, providing a compelling candidate solution to the naturalness problem of the BEH boson. The theory is testable and new physics should begin to emerge on the multi-TeV mass scales and possibly accessible to the LHC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Assessing the fidelity of marine vertebrate microfossil δ18O signatures and their potential for palaeo-ecological and -climatic reconstructions

Conodont biogenic apatite has become a preferred analytical target for oxygen isotope studies investigating ocean temperature and palaeoclimate change in the Palaeozoic. Despite the growing application in geochemical based palaeoenvironmental reconstructions, the paucity or absence of conodont fossils in certain facies necessitates greater flexibility in selection of robust oxygen bearing compounds for analysis. Microvertebrates offer a potential substitute for conodonts from the middle Palaeozoic. Microvertebrate bioapatite is particularly advantageous given a fossil record extending to the present with representatives across freshwater to fully marine environments, thus widening the scope of oxygen isotope studies on bioapatite. However, significant tissue heterogeneity within vertebrates and differential susceptibility of these tissues to diagenetic alteration have been raised as potential problems affecting the reliability of the oxygen isotope ratios as palaeoclimate proxies. Pristine microvertebrate and co-occurring conodont fossils from the Late Devonian and Early Carboniferous of the Lennard Shelf, Canning Basin, Western Australia, were analysed using bulk (gas isotope ratio mass spectrometry) and in-situ (secondary ion mass spectrometry) methodologies, with the latter technique allowing investigation of specific tissues within vertebrate elements. The δ18Oconodont results may be interpreted in terms of palaeolatitudinally and environmentally sensible palaeotemperatures and provide a baseline standard for comparison against δ18Omicrovertebrate values. Despite an absence of obvious diagenetic influences, GIRMS of microvertebrate denticles yielded δ18O values depleted by 2-4 ‰ relative to co-occurring conodonts. SIMS analysis of hypermineralised tissues in both scales and teeth produced δ18O values comparable with those of associated conodonts. The susceptibility of porous phosphatic fossil tissues to microbial activity, fluid interaction and introduction of mineral precipitates post-formation is demonstrated in microvertebrate dentine, which showed significant heterogeneity and consistent depletion in 18O. The hypermineralised tissues present in both teeth and scales appear resistant to many diagenetic processes and indicate potential for palaeoclimatic reconstructions and palaeoecological investigations.

conodont↗

Medium modifications of the bound nucleon GPDs and incoherent DVCS on nuclear targets

We study incoherent DVCS on $^4$He in the $^4{\rm He}(e,e^{\prime}\gamma p)X$ reaction, which probes medium-modifications of the bound nucleon GPDs and elastic form factors. Assuming that the bound nucleon GPDs are modified in proportion to the corresponding bound nucleon elastic form factors, as predicted in the Quark-Meson Coupling model, we develop an approach to calculate various incoherent nuclear DVCS observables. As an example, we compute the beam-spin DVCS asymmetry, and predict the $x_B$- and $t$-dependence of the ratio of the bound to free proton asymmetries, $A_{\rm LU}^{p^{\ast}}(\phi)/A_{\rm LU}^{p}(\phi)$. We find that the deviation of $A_{\rm LU}^{p^{\ast}}(\phi)/A_{\rm LU}^{p}(\phi)$ from unity is as much as $\sim$ 8\%.

Guzey, Vadim↗

Unitary constraints on neutral pion electroproduction

At large virtuality $Q^2$, the coupling to the vector meson production channels provides us with a natural explanation of the surprisingly large cross section of the neutral pion electroproduction recently measured at Jefferson Laboratory, without destroying the good agreement between the Regge pole model and the data at the real photon point. Lastly, elastic rescattering of the $\pi^0$ provides us with a way to explain why the node, that appears at $t\sim -0.5$~GeV$^2$ at the real photon point, disappears as soon as $Q^2$ differs from zero.

43 PARTICLE ACCELERATORS↗

Hydrodynamics and Load Shedding Behavior of a Variable-Geometry Oscillating Surge Wave Energy Converter (OSWEC)

In order to improve their long-term viability, wave energy converters (WECs) need to be able to shed loads when a threshold wave condition is exceeded. As shown by Tom et al. (2016) [1], provision of adjustable flaps within the body of an oscillating surge wave energy converter (OSWEC) allows wave energy to pass through the device. A control system may then be able to open and close the flaps when waves approaching the device exceed preset thresholds. The variable-geometry OSWEC (VG-OSWEC) concept studied in this paper is a bottom-hinged, rectangular wave paddle with five flaps of elliptical cross-section embedded into the face of the paddle. System ID tests were conducted on this VG-OSWEC device at a 1:14 scale in a wave basin. Free decay tests showed that the damping was distinctly nonlinear when the flaps were fully open, and the natural frequency increased by 40% when compared with the flaps in a fully closed configuration. Tests with regular wave conditions were used to develop the response amplitude operator for the rotational motion about the hinge. These response amplitude operator results when compared with numerical simulations run using WEC-Sim/WAMIT and ANSYS AQWA, show strong agreement with the flap open and closed conditions. The regular-wave condition measurements also show that the wave excitation moment about the hinge was reduced by up to 60% when the flaps were fully open. The experiments serve to demonstrate the potential of the variable geometry design to shed loads and survive harsh ocean environments.

load shedding↗

On the optimal sizing of power take-off systems for wave energy converters

The power take-off (PTO) system in a wave energy converter (WEC) is the means by which the energy in an ocean wave is converted into useful energy. There has been a general lack of technology convergence in the wave energy industry and PTO design has been largely device-specific with the design process determined by the WEC developer. An optimized PTO design can significantly affect the efficiency, reliability, performance, and overall cost and viability of a device. There remains a need in the marine energy industry for best practices and efficient design processes to be identified as it could greatly benefit developers and researchers in designing an optimal WEC PTO. This research utilizes the open-source Matlab-Simulink based software, WEC-Sim, which was developed by the National Renewable Energy Laboratory, and the Eagle, a high-performance computing system, to model and optimize two WECs of different archetypes and then investigates if any trends exist that can be exploited for greater efficiency in optimal PTO design. The results from this research indicate that there may be an optimal sizing for WEC PTOs for both power and PTO force rating and that substantial reductions can be made in the cost of a device without significant loss in the energy produced. Furthermore this optimal sizing may be independent of WEC type and deployment location. With an optimal, or near optimal, approach to WEC PTO sizing demonstrated, a methodology is proposed to address the challenge of nameplate ratings in the wave energy industry.

13 HYDRO ENERGY↗

Low-cost plasma immersion ion implantation doping for Interdigitated back passivated contact (IBPC) solar cells

Here, we present progress to develop low-cost interdigitated back contact solar cells with pc-Si/SiO 2 /c-Si passivated contacts formed by plasma immersion ion implantation (PIII). PIII is a lower-cost implantation technique than traditional beam line implantation due to its simpler design, lower operating costs, and ability to run high doses (1E14-1E18 cm -2 ) at low ion energies (20 eV-10 keV). These benefits make PIII ideal for high throughput production of patterned passivated contacts, where high-dose, low-energy implantations are made into thin (20-200 nm) a-Si layers instead of into the wafer itself. For this work symmetric passivated contact test structures (~100 nm thick) grown on n-Cz wafers with pH3 PIII doping gave implied open circuit voltage (iV oc ) values of 730 mV with J o values of 2 fA/cm 2 . Samples doped with B 2 H 6 gave iV oc values of 690 mV and J o values of 24 fA/cm 2 , outperforming BF 3 doping, which gave iV oc values in the 660-680 mV range. Samples were further characterized by SIMS, photoluminescence, TEM, EELS, and post-metallization TLM to reveal micro- and macro-scopic structural, chemical and electrical information.

14 SOLAR ENERGY↗

Screen printable copper pastes for silicon solar cells

The current work demonstrates the successful metallization of a PERC silicon solar cell with screen-printable copper (Cu) paste that is sintered at elevated temperature in air atmosphere. The existing state of the art in Silicon (Si) solar cell metallization is silver (Ag) paste; Cu cost is 1/100th the cost of Ag and has a comparable conductivity. However, Cu undergoes rapid oxidation at elevated temperatures and the high diffusion of Cu into Si restricts its usage in the metallization of silicon solar cells. In this paper, a Cu paste containing a proprietary mixture of antioxidant additives and diffusion inhibitors was used to make front gridlines on PERC cells. The Cu-printed cells were fired in an IR belt furnace with a peak temperature of 576°C in air atmosphere. The solar cells discussed here reached an efficiency of 19%, which is 88% of the efficiency measured for a commercial Ag-printed cell. The working devices were further characterized using STEM, EDX, ToF-SIMS and long-term suns-V oc studies demonstrating an absence of Cu diffusion. Furthermore, thermally stressing the Cu-printed solar cells yielded a reduction of less than 1.9% of the initial pseudo fill factor (pFF) after 1000 hours at 200°C. Here, the shunt resistance of cells monitored over 3 years remained within 2.5% of its initial value, which demonstrates the effectiveness of the Cu diffusion barrier.

14 SOLAR ENERGY↗