Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

The Effect of Valve Cooling upon Maximum Permissible Engine Output as Limited by Knock

A Wright GR-1820-G200 cylinder was tested over a wide range of fuel-air ratios at maximum permissible power output as limited by knock with three different degrees of valve cooling. The valves used were stock valves (solid inlet valve and hollow sodium-cooled exhaust valve), hollow valves with no coolant, and hollow valves with flowing water as a coolant. Curves showing the variation in maximum permissible values of inlet-air pressure, indicated mean effective pressure, cylinder charge, and indicated specific fuel consumption with change in fuel-air ratio and valve cooling are shown. The use of valves cooled by a stream of water passing through their hollow interiors permitted indicated mean effective pressures 10 percent higher than the mean effective pressures permissible with stock valves when the engine was operated with fuel-air ratios from 0.055 to 0.065. Operation of the engine with lean mixtures with uncooled hollow valves resulted in power output below the output obtained with the stock valves. The data show an increase in maximum permissible indicated mean effective pressure due to cooling the valves, which averages only 2.1 percent with fuel-air ratios from 0.075 to 0.105.

Munger, Maurice↗

2D photofragmentation LIF imaging of H 2 O 2 and HO 2 in the effluent of an atmospheric-pressure plasma jet: effects of solid and liquid interfaces

Two-dimensional (2D) absolute measurements of hydrogen peroxide (H 2 O 2 ) and approximations of the hydroperoxyl radical (HO 2 ) in the effluent of a COST Reference Microplasma Jet operated with a He/H 2 O feed gas are presented. Gas-phase densities are mapped using photofragmentation laser-induced fluorescence (PF-LIF) under three boundary conditions: open effluent, a solid target, and a liquid target. A novel method is presented for separating PF-LIF signals from H 2 O 2 and HO 2 using comparative measurements in oxygen-rich and oxygen-free environments to exploit the preferential formation of HO 2 in the presence of molecular oxygen. This separation strategy is supported by results from a plug-flow plasma chemistry model. Measured densities agree closely with model predictions in both magnitude and trend, while the 2D experimental distributions provide additional insight into the spatial dependencies of these species. In particular, the results show distinct differences in species transport depending on the target type: solid surfaces induce lateral deflection and reduced centerline densities, whereas liquid interfaces promote axial accumulation and higher near-axis concentrations.

atmospheric-pressure plasma jet (APPJ)↗

Effects of Forming Pressure on Physicochemical Properties of YBCO Ceramics

This article details the solid-state synthesis of high-temperature superconducting YBa{sub 2}Cu{sub 3}O{sub 7−x}. Tests were carried out on samples formed at different pressures (200, 400, 600 and 800 MPa) before being annealed under pure oxygen. The X-ray diffraction method showed that, regardless of the forming pressure, the samples contain about 97 wt.% of Y-123 phase. SEM images showed a polycrystalline structure of samples of similar grain size and number of pores (intergranular spaces). The values of critical temperatures (T{sub c0}), determined from magnetoresistance measurements, are about 91.5 K for all samples, and the T{sub c0} temperatures do not depend on sample-forming pressure. Magnetoresistance measurements have shown that samples formed with higher pressures exhibit smaller changes in T{sub c0} and superconducting transition width ΔT due to the influence of the H{sub DC} magnetic field, than the samples formed with lower pressures. Values of specific resistance determined by the use of van der Pauw method at 300 K is about 2 mΩcm for all samples. The critical temperatures (T cintra) of grains and critical current densities at 77 K were determined from AC magnetic susceptibility measurements, and they are about 91.6 K and 400 A cm{sup −2}, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Oxygen Pressure on Thermoelectric Properties of p-Type CuAlO{sub 2} Films Fabricated by Pulsed Laser Deposition

We focus on the growth of p-type CuAlO{sub 2} thin films and its thermoelectric properties. Thin films are deposited by pulsed laser deposition technique on single-crystal sapphire substrates varying the oxygen partial pressure. Thin film deposited at oxygen partial pressure of 200 mTorr presents bigger grains (about 10 μm in size) and shows Seebeck coefficient as high as 270 µV/K with a conductivity of about 0.8 S/cm so that its power factor is about 5.7 µW/mK{sup 2} at 800 K, twice than observed in the film deposited at 60 mTorr of oxygen.

36 MATERIALS SCIENCE↗

Enhanced Mechanical, Tribological, and Thermal Properties of Fe{sub 3}Al Composites with Carbon Nanotubes

In this work, Fe{sub 3}Al-based composites reinforced with carbon nanotubes were fabricated by a hot-press sintering process under various sintering pressures. The effects of sintering pressure and additives (alumina and lanthanum) on both the physical and the mechanical properties were systematically investigated. Results showed that with the sintering pressure of 15 MPa and incorporation of carbon nanotubes (CNTs), the microhardness of Fe{sub 3}Al composite exhibited a peak value at 1038.1 HV, which was ~ 60% higher than those without the addition of carbon nanotubes (644.9 HV). Also, both the compressive yield strength and the thermal conductivity of Fe{sub 3}Al composite were also significantly improved. Results of wear test showed the Fe{sub 3}Al composite exhibited a low wearing rate (10{sup −6}-10{sup −5} order of magnitude) and a friction coefficient (0.53-0.67).

36 MATERIALS SCIENCE↗

Effect on blood pressure and eye health symptoms in a climate-financed randomized cookstove intervention study in rural India

Highlights: • Health benefits from a climate-financed cookstove intervention were limited. • Blood pressure changes were not significant in homes using intervention stoves. • Eye-irritation generally improved, suggesting unmeasured exposures or reporting bias. • Stove adoption and use behavior, in addition to stove technology, can complicate attainment of health benefits. Air pollution from cooking with solid fuels is a potentially modifiable risk factor for increased blood pressure and may lead to eye irritation.

54 ENVIRONMENTAL SCIENCES↗

Effects of operating pressure on flame oscillation and emission characteristics in a partially premixed swirl combustor

The influence of varying combustor pressure on flame oscillation and emission characteristics in the partially premixed turbulent flame were investigated. In order to investigate combustion characteristics in the partially premixed turbulent flame, the combustor pressure was controlled in the range of -30 to 30 kPa for each equivalence ratio ({phi} = 0.8-1.2). The r.m.s. of the pressure fluctuations increased with decreasing combustor pressure for the lean condition. The combustor pressure had a sizeable influence on combustion oscillation, whose dominant frequency varied with the combustor pressure. Combustion instabilities could be controlled by increasing the turbulent intensity of the unburned mixture under the lean condition. An unstable flame was caused by incomplete combustion; hence, EICO greatly increased. Furthermore, EINO{sub x} simply reduced with decreasing combustor pressure at a rate of 0.035 g/10 kPa. The possibility of combustion control on the combusting mode and exhaust gas emission was demonstrated. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗