Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Effect of Heat Treatment on Microstructure and Magnetic Properties of Ce-Doped NdFeB Ribbons

The substitution for Nd by abundant element cerium (Ce) is a practical way for the comprehensive utilization of rare earth resources in NdFeB permanent magnets. In this letter, we have prepared the Ce-doped NdFeB ribbons and conventional NdFeB ribbons by melt quenching method and investigated the effects of heat treatment on the crystallization behavior, microstructure, and magnetic properties of the alloy. The results show that: (1) The crystallization behavior and the microstructural changes of the (Nd,Ce)FeB magnets are similar to the conventional NdFeB magnet when heat treatment. In addition, the Ce{sub 2}Fe{sub 14}B phase has a significant effect on the properties of the whole magnets. (2)The NdFeB phase and CeFeB phase are relatively close to each other after being precipitated from the amorphous phase. The coupling effect between the two phases is strong enough to weaken the effect of the addition of Ce and making the properties of the NdFeB magnets to not reduce too much after adding Ce.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Microstructure and Magnetic Properties of Exchange-Coupled Co{sub 72}Pt{sub 28}/Pt/Co{sub 81}Ir{sub 19} Composite Media for Perpendicular Magnetic Recording

In this work, we report the investigation of microstructure and magnetic properties of the Co{sub 72}Pt{sub 28}/Pt/Co{sub 81}Ir{sub 19} exchange-coupled composite (ECC) media using soft-layer (SL) of Co{sub 81}Ir{sub 19} with negative magnetocrystalline anisotropy (MA). Our TEM images show that the hard-layer (HL) exhibits a columnar type microstructure with well-isolated grains and the exchange-coupled SL with hcp-structure show the same texture. Strong coupling of the two layers have been evidenced by the magnetic characterization for all the studied films with Pt inter-layer thickness ranging from 0 to 2 nm. Importantly, these ECC media films have much lower coercivities and much higher thermal stabilities in the favor of high-density magnetic recording.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Transient-Liquid-Phase Bonding of H230 Ni-Based Alloy Using Ni-P Interlayer: Microstructure and Mechanical Properties

Transient-liquid-phase bonding using Ni-P as an interlayer has been developed for H230 Ni-Cr-W solid-solution-strengthened Ni-based alloy. Two process parameters—composition of the interlayer and bonding time—have been varied to optimize the mechanical properties. H230 has been bonded into two sets of stacks (set I and II) for 8 and 4 hours using Ni-12P and Ni-6P interlayer, respectively, (wt pct) at 1423 K (1150 °C) and 12.7 MPa. The microstructure of both the stacks has three distinct regions—the joint centerline which showed the presence of pores, an isothermally solidified zone (ISZ) which did not have any carbide precipitates and base H230. Transmission electron microscopy and atom probe tomography showed a uniform microstructure, and an absence of any deleterious phases at the joint and in ISZ. Set I and set II had a yield strength of 76 and 86 pct of that of the H230 sheet, tested at 1023 K (750 °C). Here, the measured elongation at fracture was negligible, but the fracture surfaces revealed a ductile cup-and-cone-type fracture occurring through the ISZ/joint region. Examination of broken tensile samples revealed that the plastic strain was constrained to within one joint region through which fracture occurred.

14 SOLAR ENERGY↗
DOE OSTI2025

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In-Situ Synchrotron X-Ray Diffraction of Ultrasonic Microstructural Refinement During Solidification in a Commercial Al–Si–Mg Alloy

This study reports the first use of in-situ synchrotron X-ray diffraction (SXRD) to study the effects of ultrasonic melt processing (USMP) on phase and grain size evolution during solidification in a commercial Al–Si–Mg casting alloy. USMP is a technique that, when applied to aluminum as it solidifies, can be used to refine the local microstructure of large-scale castings. Analysis of the in-situ SXRD data to estimate the average grain size of primary α-Al grains during USMP demonstrates that USMP slows the growth rate of α-Al grains and reduces grain size by 36 pct. Furthermore, there is also evidence that USMP causes the primary α-Al grains to move relative to the X-ray beam; such motion increases the probability of primary α-Al grains colliding and fragmenting. This movement becomes constrained at the onset of the Al–Si binary eutectic, suggesting that USMP ceases to effectively refine the microstructure once the Al–Si binary eutectic begins to form. Complementary laboratory-scale X-ray diffraction (XRD) data were used to correlate the lattice parameters of the α-Al and Si (D-A4) phases with temperature to estimate cooling rate during solidification. Thus, this study can guide the design of novel castings with spatially distributed fine-grained regions produced using local ultrasonic processing.

Aluminum Alloys↗
DOE OSTI2017

Thermal Simulation Analysis of Microstructure and Hardness for CrMoV with PWHT in Type IV Region

Welded components of CrMoV steam pipe exhibit a pernicious form of type IV cracking after long-term service at elevated temperature. To investigate the cracking mechanism, the type IV microstructure and hardness were characterized after thermal simulation of post-weld heat treatment. Below 1098 K (825 °C), loss of carbon from the pearlite region was apparent, and the work zone exhibited a slightly lower hardness than the parent material because of a minor amount of austenite transformation. In addition, for peak temperatures above 1133 K (860 °C), additional transformation into austenite occurred and was followed by retransformation into ferrite upon further increasing the temperature. The pearlite formed at 1173 K to 1223 K (900 °C to 950 °C) resulted in an increase of the volume fraction of pearlite and microstructural refinement, which yielded a remarkable increase of hardness in the work zone. For the peak temperature of 1573 K (1300 °C), previous austenite grains were coarsened and alloy carbides were dissolved in the austenite, which significantly hardened the work zone.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Investigation of the Influence of Heat Balance Shifts on the Freeze Microstructure and Composition in Aluminum Smelting Bath System: Cryolite-CaF{sub 2}-AlF{sub 3}-Al{sub 2}O{sub 3}

In an aluminum electrolysis cell, the side ledge forms on side walls to protect it from the corrosive cryolitic bath. In this study, a series of laboratory analogue experiments have been carried out to investigate the microstructure and composition of side ledge (freeze linings) at different heat balance steady states. Three distinct layers are found in the freeze linings formed in the designed Cryolite-CaF{sub 2}-AlF{sub 3}-Al{sub 2}O{sub 3} electrolyte system: a closed (columnar) crystalline layer, an open crystalline layer, and a sealing layer. This layered structure changes when the heat balance is shifted between different steady states, by melting or freezing the open crystalline layer. Phase chemistry of the freeze lining is studied in this paper to understand the side ledge formation process upon heat balance shifts. Electron probe X-ray microanalysis (EPMA) is used to characterize the microstructure and compositions of distinct phases existing in the freeze linings, which are identified as cryolite, chiolite, Ca-cryolite, and alumina. A freeze formation mechanism is further developed based on these microstructural/compositional investigations and also thermodynamic calculations through the software—FactSage. It is found that entrapped liquid channels exist in the open crystalline layer, assisting with the mass transfer between solidified crystals and bulk molten bath.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Properties of Fe{sub 3}Al-Fe{sub 3}AlC{sub x} Composite Prepared by Reactive Liquid Processing

A Fe{sub 3}Al-Fe{sub 3}AlC{sub x} composite was prepared using reactive liquid processing (RLP) through controlled mixture of carbon steel and aluminum in the liquid state. The microstructure and phases of the composite were assessed using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, optical microscopy, and differential scanning calorimetry. In addition, the density, hardness, microhardness, and elastic modulus were evaluated. The Fe{sub 3}Al-Fe{sub 3}AlC{sub x} composite consisted of 65 vol pct Fe{sub 3}Al and 35 vol pct Fe{sub 3}AlC{sub x} (κ). The κ phase contained 10.62 at. pct C, resulting in the stoichiometry Fe{sub 3}AlC{sub 0.475}. The elastic modulus of the Fe{sub 3}Al-Fe{sub 3}AlC{sub 0.475} composite followed the rule of mixtures. The RLP technique was shown to be capable of producing Fe{sub 3}Al-Fe{sub 3}AlC{sub 0.475} with a microstructure and properties similar to those achieved using other processing techniques reported in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Mechanical Properties, Microstructural Evolution, and the Effect of Friction on the Plastic Flow of the AISI 321 Austenitic Stainless Steel Tube During Cold Pilgering: An Experimental and Simulation Analysis

The mechanical properties, microstructural evolution, and the effect of friction on the plastic flow of the AISI 321 austenitic stainless steel (ASS) tube were investigated during the cold pilger process. The elastic–plastic behavior of as-received tube was simulated by the Johnson-cook model. The model parameters were obtained by the compression and tensile tests. The mechanical properties of the material were examined by the tensile and microhardness tests. Based on the ring compression test results, three different situations for friction conditions were considered. The stress and strain states at these conditions were examined for the outer and inner surfaces of the tube. Numerical evaluation of plastic shearing due to the cold pilgering of the AISI321 tube was performed. The X-ray diffraction, ferrite scope tests, and optical microscope were also used for the microstructure evaluation and verification of the simulation results, respectively. The Latham-Cockcraft damage was calculated for different conditions by introducing the new subroutine, showing that it was strongly dependent on the friction conditions and the shear strain, ε{sub zr}, respectively. It was shown that the friction coefficient of 0.3 resulted in the minimum damage of the tube and the different friction conditions between the two surfaces of the tube enhanced the damage function. Also, the strain induced ά-martensite increased the work-hardening capacity and affected the ductility of the tube.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High-Temperature Properties and Microstructural Stability of the AISI H13 Hot-Work Tool Steel Processed by Selective Laser Melting

The microstructural stabilities, softening resistance, and high-temperature tensile properties of the H13 hot-work tool steel by selective laser melting (SLM) were systematically studied. A series of tempering procedures were performed on the as-SLMed specimens. Afterwards, the mechanism of softening resistance behavior was discussed based on the XRD, SEM, EBSD observations, hardness measurements, and high-temperature tensile tests. It was found that the as-SLMed H13 consisted of α-iron and γ-iron. The carbide-stabilizing elements aggregated as the cell-like substructures for the rapid solidification of the SLM process. After the softening resistance treatment, the retained austenite transformed to ferrite and carbide mixtures. The cell-like substructures dissolved slowly into the matrix when the temperature was below 550 °C. These factors increased the hardness and retarded the softening of the material. When the temperature was 600 °C, the microstructural constituents transformed to soft ferrite and globular carbides, which lead to a considerable decrease of the hardness. Due to the grain refinement, solid solution strengthening, and residual stress, the as-SLMed H13 exhibited better mechanical properties than that of the wrought counterparts.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Characterization of Solidification Microstructures in Vacuum Arc Remelted Nickel Alloy 718

Digital image analysis techniques were developed to autonomously characterize dendritic solidification features in microstructures of a nickel alloy 718 ingot produced by vacuum arc remelting (VAR). Automated macrophotography was implemented to image microstructures and produce large image montages of etched ingot cross sections. Two image analysis techniques, particle identification and two-point correlation, were applied to autonomously measure primary dendrite arm orientation and secondary dendrite arm spacing from the image montages. Particle identification measured individual dendritic features. The two-point correlation technique measured averaged feature values over defined image areas. These methods are described and compared. Melt pool profile and solidification time histories were reconstructed from primary dendrite arm orientation and secondary dendrite arm spacing measurements, respectively. These characterization techniques provide two new methods of reconstructing melt pool profiles and solidification times in cast ingots. The information produced is expected to be useful in the validation of computational models for solidification during VAR, similar remelting processes, and general casting processes that produce dendritic solidification features.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Modeling of the α + β Phase in Ti-6Al-4V: A Diffusion-Based Approach

Complex heat treatment operations and advanced manufacturing processes such as laser or electron-beam welding will see the metallic workpiece experience a considerable range of temperatures and heating/cooling rates. These intrinsic conditions will have a significant bearing upon the microstructure of the material, and in turn upon the thermo-mechanical properties. In this work, a diffusion-based approach to model the growth and shrinkage of precipitates in the alpha + beta field of the common titanium alloy Ti-6Al-4V is established. Further, the numerical model is extended using a JMA-type approach to explore the dependency of the beta-transus temperature on extremely high heating rates, whereby dissolution alone is too slow to accurately describe the alpha to beta-phase transformation. Experimental heat treatments at rates of 5, 50, and 500 °C/s were performed, and metallographic analysis of the samples was used to validate the numerical modeling framework predictions for lamellar shrinkage, while data from the literature has been used to evaluate the numerical modeling framework for the growth of equiaxed microstructures. The agreement between measurements and numerical predictions was found to be good.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Fabrication of AZ31/MWCNTs Surface Metal Matrix Composites by Friction Stir Processing: Investigation of Microstructure and Mechanical Properties

The surface metal matrix composites of AZ31 Mg alloy reinforced with multiwall carbon nanotubes (MWCNTs) have been fabricated through the friction stir processing by a conventional and two stepped tools. The microstructure and mechanical properties of fabricated composites were studied by optical and electron microscopy, microhardness and tensile tests, respectively. The processing has developed a fine-grain structure along with good distribution of reinforcements. The hardness and tensile strength of fabricated MWCNT/AZ31 composites are generally higher than as-received and FSPed samples. The accumulative effect of grain refinement and reinforcing nanotubes is assumed to be the reason for increasing the ductility after friction stir processing. The hardness is nearly doubled for FSPed samples and some more for nanocomposites compared with the as-received sample. The elongation of nanocomposites is about two times greater than that of the as-rolled sample. The speed ratio, pass number and CNT amount are three important factors influencing the resulting microstructure and mechanical properties. The stepped tools also give a more uniform distribution of reinforcement and higher grain refinement.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Tempering Temperature on the Microstructure and Properties of Fe-2Cr-Mo-0.12C Pressure Vessel Steel

To obtain the high-temperature strength and toughness of the medium–high-temperature–pressure steel, the microstructure evolution and mechanical properties of Fe-2Cr-Mo-0.12C steel subjected to three different tempering temperatures after being normalized were investigated. The results show that the microstructure of the sample, tempered in the range 675-725 °C for 50 min, did not change dramatically, yet the martensite/austenite constituents decomposed, and the bainite lath merged together and transformed into polygonal ferrite. At the same time, the precipitate size increased with an increase in tempering temperature. With the increase in the tempering temperature from 675 to 725 °C, the impact absorbed energy of the Fe-2Cr-Mo-0.12C steel at −40 °C increased from 257 to 325 J, and the high-temperature yield strength decreased; however, the high-temperature ultimate tensile strength tempered at 700 °C was outstanding (422-571 MPa) at different tested temperatures. The variations of the properties were attributed to the decomposition of M/A constituents and the coarsening of the precipitates. Fe-2Cr-Mo-0.12C steel normalized at 930 °C and tempered at 700 °C was found to have the best combination of ductility and strength.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effects of Overlapping Distances on Steel Microstructure and Properties After Multi-track Laser Quenching

In this study, multi-track laser quenching with different overlapping distances was used to assess SM45C microstructure and properties. Two overlapping distance types were evaluated, including overlapping distances in the transition and martensite regions, respectively. After multi-track quenching, hardness showed a threefold increase. With the overlapping distance in the transition region, surface hardness varied from 600 to 700 HV. There was a region of low hardness in each track. Hardness in the low hardness region was from 300 to 400 HV. The average hardness was basically over 500 HV with the overlapping distance in the martensite region, although there was a softening region. The increased hardness was mainly caused by the martensite. Microstructure in the overlapping region was self-tempered martensite, retained austenite and ferrite. Tempered sorbite and lowly tempered martensite were observed in heat-affected zones. Friction coefficients of quenched specimens varied between 0.275 and 0.325, with a 14% reduction relative to the base metal. The wear rate of the quenched specimen was only 40.8% of the base metal. With time, mass reduction in the quenched specimen was much smaller than that of the base metal. For specimens treated with laser quenching, slight fatigue wear was dominating.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructure Evolution During Continuous Cooling in AISI 5140 Steel Processed by Induction Heating Chromizing

In this study, induction heating chromizing (IHC) and box-type furnace heating chromizing (BFHC) were conducted on commercial AISI 5140 steels, respectively. Microstructure, microhardness and wear resistance of the chromized samples were characterized. The results show that the IHC samples have thicker Cr coating layer and stronger interface bond due to pre-compressive stress among the packed powders. Three kinds of microstructures including alloyed cementite (AC-layer), fine pearlite zone (FP-zone) and carbon-poor zone (CP-zone) are formed near the interface in the IHC samples. The main reason given for this is that different contents of Cr and C have different effects on pearlite phase and morphology. The IHC sample shows better wear properties due to its stronger interface bonding strength than that of the BFHC sample. The formation mechanism of CP-zone and its influences on microhardness and wear resistance are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Surface Layers of Zr-18%Nb Alloy Modified by Ultrasonic Impact Treatment: Microstructure, Hardness and Corrosion

Near-surface layers in Zr-18%Nb alloy were modified using ultrasonic impact treatment (UIT). The effects of the UIT processing time on a microstructural formation, omega/alpha precipitations, microhardness and corrosion are analyzed. XRD analysis, TEM and SEM observations and EDX characterization allow establishing the links between the microstructure, microhardness and corrosion behavior of the surface layers formed. At the strain extent up to e ≈ 0.3, structural formation occurs under influence of deformation induced heating, which facilitates omega precipitation in beta phase and mechanically induced oxygen transport and oxide formation. XRD analysis reveals moderate compressive residual stresses (− 160 MPa) and pronounced {110} texture after the UIT process. Generation of dislocations and hindering of their movement by nanoscale omega precipitates manifest themselves as the broadening of diffraction peaks occurred mainly owing to the lattice microstrains, and they provide marked strain hardening. The enhanced anticorrosion properties of Zr-18%Nb alloy in saline solution were concluded to be a result of the formation of a protective oxide film, {110} texture and compressive stresses.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructure and Interfacial Shear Strength in W/(Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5}){sub 100−x}Nb{sub x} Composites

In the present study, (Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5}){sub 100−x}Nb{sub (x=0,1,2,3)} bulk metallic glass matrix/tungsten wire composites were fabricated by a gas pressure infiltration process at temperature 950 °C for 5 min. Microstructural studies and mechanical behaviors of the materials have been investigated by scanning electron microscopy, transmission electron microscopy and pullout tests. The mechanical results showed that the interface shear strength in the composite sample with X = 2 increased more than twice compared to the composite sample with X = 0. Based on the microstructural results, the addition of two atomic percent Nb in the matrix composite causes an increase in the diffusion band thickness during the melt infiltration and change in the interface fracture mode as a result of pullout test.

36 MATERIALS SCIENCE↗