Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MOLDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Static and Dynamic Mechanical Properties of Graphene Oxide-Incorporated Woven Carbon Fiber/Epoxy Composite

This study investigates the synergistic effects of graphene oxide (GO) on the woven carbon fiber (CF)-reinforced epoxy composites. The GO nanofiller was incorporated into the epoxy resin with variations in the content, and the CF/epoxy composites were manufactured using a vacuum-assisted resin transfer molding process and then cured at 70 and 120 °C. An analysis of the mechanical properties of the GO (0.2 wt.%)/CF/epoxy composites showed an improvement in the tensile strength, Young’s modulus, toughness, flexural strength and flexural modulus by ~ 34, 20, 83, 55 and 31%, respectively, when compared to the CF/epoxy composite. The dynamic mechanical analysis of the composites exhibited an enhancement of ~ 56, 114 and 22% in the storage modulus, loss modulus and damping capacity (tanδ), respectively, at its glass transition temperature. The fiber–matrix interaction was studied using a Cole–Cole plot analysis.

36 MATERIALS SCIENCE↗

Fracture Strength and Surface Magnetic Flux Uniformity in an Isotropic Polymer-Bonded Ring-Shaped Nd-Fe-B Magnet

Ring-shaped (RS) polymer-bonded magnets were produced from a mixture of an isotropic nanocrystalline Nd-Fe-B powder with a nominal composition of 59.8 wt.% Fe, 29 wt.% Nd, 5 wt.% Zr, 4.8 wt.% Co and 1.4 wt.% B and a variety of epoxy resins as binders, using a compaction-molding technique. The morphology and average particle size of the powders are determined by an SEM. The magnetic properties of the magnets were measured using a permeameter. Magnetic flux on the surface of the magnets was determined by a Gauss meter. The mechanical properties of the RS specimens were determined using a tensile fracture strength (FS) test. The effects of polymer type and amount, hardener amount, applied pressing pressure and curing temperature and time on FS were investigated. The experimental results showed that at optimal conditions of 8 wt.% solid epoxy, 3.5 wt.% solid hardener, a pressing pressure of 900 MPa and a curing time of 8 h at 170 °C, a maximum tensile strength of ~ 36 MPa was achieved. Surface magnetic flux uniformity in optimal mechanical conditions was also found to be optimum at around ± 40 G, which is one of the best flux uniformities in bonded magnets.

36 MATERIALS SCIENCE↗

Change in Porosity of A356 by Holding Time and Its Effect on Mechanical Properties

In most of the practical casting operations, it is important to be able to cast large number of part with one single melt. Therefore, when quantity of the charge and melting crucible is increased, during casting process, the liquid is led to settle for a long period of time. In this work, 10 kg charge of A356 was melted at 750 °C and held for 240 min. A sand mold with different thickness was cast at 30, 60, 120, and 240 min of holding time of the liquid, before and after degassing conditions. Melt quality was measured by reduced pressure test, and pore size and number were measured at each cast part. A correlation between bifilm index and tensile properties was established. It was found that melt quality was decreased with increased holding time and pore formation was enhanced linearly. Additionally, mechanical properties of the alloy were decreased with decreased melt quality and increased pore formation due to holding time of the liquid.

36 MATERIALS SCIENCE↗

A Low-Cost Lightweight Entropic Alloy with High Strength

In this study, a series of lightweight Al–Mg system entropic alloys containing Zn, Cu, and Si were designed based on the order/disorder or entropy, and eutectic concepts. The alloys of Al{sub 58.5}Mg{sub 31.5}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 63}Mg{sub 27}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 66.7}Mg{sub 23.3}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 80}Mg{sub 14}Zn{sub 2.7}Cu{sub 2.7}Si{sub 0.6}; Al{sub 85}Mg{sub 10.5}Zn{sub 2.025}Cu{sub 2.025}Si{sub 0.45}; and Al{sub 90}Mg{sub 7}Zn{sub 1.35}Cu{sub 1.35}Si{sub 0.3} were prepared by induction melting under a high-purity argon atmosphere and then casted into stainless steel molds. The microstructures which were tested in the as-cast state exhibited multiphases and contained apparent volume fractions of intermetallic compounds and solid solutions. Then, the compressive mechanical properties of the alloys were measured, and high fracture strengths of 577, 677, 590, 498, 814, and 794 MPa, respectively, were determined. Strong hardening phenomena were observed in the Al{sub 80}Mg{sub 14}Zn{sub 2.7}Cu{sub 2.7}Si{sub 0.6}, Al{sub 85}Mg{sub 10.5}Zn{sub 2.025}Cu{sub 2.025}Si{sub 0.45}, and Al{sub 90}Mg{sub 7}Zn{sub 1.35}Cu{sub 1.35}Si{sub 0.3} alloys at room temperature, with amazing plasticity percentages of 13.8, 24.8, and 32.7%, respectively. The property differences in the lightweight alloys were analyzed using the following parameters: the critical values of the enthalpy of mixing; atomic size differences; ratio of entropy to enthalpy; valence electron concentration (VEC); and Pauling electronegativity difference. Finally, three of the aforementioned parameters (atomic size difference, enthalpy of mixing, and Pauling electronegativity difference) were regarded in this study as the crucial rules for the lightweight multicomponent alloys.

36 MATERIALS SCIENCE↗

Impact Behavior of Polyester GFRP for Naval Applications: Influence of the Clamping Device and Fluid–Material Interaction

The low-velocity impact behavior of polyester glass fiber composite laminates has been investigated under different clamping conditions, by wetting the specimens surface with fluids having different densities. Unidirectional composite laminates, based on polymer resin and fibers of naval interest, with different thicknesses have been manufactured by resin transfer molding process in order to have a high control of the final properties and a high fiber volume fraction. Impact tests in air have been, first, performed up to penetration on all manufactured composites having four different thicknesses to get information on the material impact behavior. The effect of the clamping conditions and the interaction of the laminates with two fluids different in density, i.e., water and paraffin oil, have been investigated, then, only on the thickest laminates that showed a lower tendency to impact damage. In particular, the impact tests have been performed by impacting the front surface of the sample and by wetting the back surface of the composite samples under unclamped and clamped conditions, replicating the boundary constraints suggested by ASTM D7136 Standard for the conventional impact tests. Experimental results showed a lower initial rigidity, higher absorbed energy and deflection for specimens exposed to liquids with respect to those exposed to air, confirming the need of taking into account the fluid interaction in the case of marine composite applications.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of As-Cast γ-TiAl Alloys with Different Cooling Rates

γ-TiAl alloys composed of Ti-45Al-5Nb-1W-1B (at.%) solidified at three different cooling rates by vacuum electromagnetic induction melting under a controlled degree of vacuum of under 2 Pa. The influence of the cooling rate on the microstructure and mechanical properties of the γ-TiAl alloy samples was investigated. A relatively large temperature gradient at the beginning of solidification led to a thin fine-grained layer around the graphite mold, and undercooling had two main effects: (a) promoting nucleation in the grain-refining surface layer and (b) promoting the growth of columnar crystals beneath the surface. Moreover, all prepared ingots of this alloy could be clearly divided into Regions S, M and C from the surface to the core. The colony size of Region M was larger than those of the other two regions due to composition segregation and the growth of columnar grains. The existence of tungsten led to micro-inhomogeneity, and the mechanical properties of the alloy changed according to concentration fluctuations. The degrees of homogeneity were expressed as H{sub 0.1} and H{sub 0.2}. The alloy with the highest values, which possesses the best mechanical properties, solidified at a relatively low cooling rate. The deformation mechanism is also discussed.

36 MATERIALS SCIENCE↗

Modeling and Computation of Casting Process by Particle Method

Since particle-based computational methods, such as smoothed particle hydrodynamics (SPH) method, are suitable to treat free surfaces and moving boundaries, it is expected that the simulation with particle methods can represent more accurate molten metal flow. Hence, we apply the SPH method to some casting processes and validate the numerical results by comparing with experiments. While fluid behaviors of the transportation and the mold filling processes are expressed sufficiently, ladle pouring process of aluminum alloy is not reproduced by the existing scheme. So we developed a new numerical model of surface oxide film, and our numerical results show good agreement with the experimental data.

36 MATERIALS SCIENCE↗

Role of Titanium, Carbon, Boron, and Zirconium in Carbide and Porosity Formation during Equiaxed Solidification of Nickel-Based Superalloys

This work analyses the effect of Ti in the MC carbide formation and also in the γ/γ´ eutectic promotion in two nickel-based alloys melted under vacuum conditions and solidified into ceramic molds. The role of boron, carbon and zirconium on the porosity level after solidification of both alloys was also investigated; since the alloys were vacuum melted, it is assumed that the observed porosity is due to micro-shrinkage. The chemical compositions for two alloys were: 20.2Cr-13.7Co-4.78Mo-1.19Al-0.69Ti-0.08C-2.34Fe for Alloy 1, and 20.5Cr-15.6Co5.03Mo-1.57Al-3.42Ti-0.15C-1.64Fe-0.076Zr-0.01%B for Alloy 2. Results showed a higher volume fraction of MC carbides and the γ/γ´ eutectic for the Alloy 2 with higher titanium content since this element is a carbide and γ/γ´ eutectic promoter. The porosity level in the Alloy 2, with higher amounts of carbon, boron and zirconium was considerably lower than that for the Alloy 1. These results are discussed in terms of different phenomena caused by the segregating effects of boron, carbon and zirconium towards the interdendritic regions and the formation of zirconium carbides that produce an expansion in volume when they are formed at the end of the solidification process.

36 MATERIALS SCIENCE↗

High-Resolution Electron Microscopy and Kinetic Studies of Precipitation Hardening Reactions in Cast Al-5.8Zn-2.2Mg-2.5Cu

Precipitation age hardening (T6) response of Al-5.8Zn-2.2Mg-2.5Cu alloy in near-net-shaped cast condition was investigated. Cast samples were manufactured using the controlled diffusion solidification (CDS) technology combined with a metallic mold tilt pour gravity casting process. This study was conducted using (1) non-isothermal aging during differential scanning calorimetry (DSC) experiments and (2) isothermal aging during which transient bulk and micro-hardness measurements taken at four aging temperatures of 343, 393, 433 and 473 K. A detailed microstructural investigation combined with a quantitative image analysis was carried out on both DSC and hardness specimens using high-resolution electron microscopy (HREM) and energy-dispersive spectroscopy (EDS) elemental mappings. Hardness measurements were analyzed using a kinetic modeling approach (single state variable combined with a kinetic equation that is valid for the Al-Zn-Mg-Cu alloys). The results confirm the formation of hardening phases of GP zone, intermediate hardening metastable phase η′ and equilibrium phase η. The results of calorimetric measurements, electron microscopy and selected area diffraction patterns are in good agreement and confirm transient precipitation/dissolution sequences. A mean value of activation energy Q{sub A} of 75 kJ/mol was evaluated for combined bulk diffusion rate of alloying elements during precipitation of strengthening phases within Al matrix.

36 MATERIALS SCIENCE↗

Aqueous Corrosion Behavior of Cast CoCrFeMnNi Alloy

CoCrFeMnNi high-entropy alloy demonstrates good mechanical properties and can be further strengthened by thermomechanical processes. A sample alloy prepared by vacuum casting in a graphite mold was further investigated for its corrosion resistance. One-millimeter thin strips of cast alloy were used to investigate its corrosion behavior at room temperature. Linear potentiodynamic tests of the alloy in sodium chloride solution confirmed uniform corrosion property comparable to stainless steel AISI 304. However, a positive cyclic hysteresis loop indicated susceptibility to pitting corrosion. In sodium hydroxide solution, metastable pit formation was observed, while sulfuric acid solution passivated the alloy. In both cases, the alloy did not show any spontaneous pitting tendency.

36 MATERIALS SCIENCE↗

Characteristics and Tribological Behaviors of TiAlN/Cr-Ni Composite Coatings at Elevated Temperatures

A TiAlN/Cr-Ni composite coating was fabricated on H13 hot work mold steel using a cathode ion arc plating and laser cladding. The surface and cross-sectional morphologies, chemical compositions, phases and surface roughness of obtained coating were analyzed using a scanning electron microscope, energy disperse spectroscopy, x-ray diffraction and atomic force microscope, respectively, and the bonding strength was measured using a scratch test. The friction-wear properties of TiAlN/Cr-Ni coating at 400, 500 and 600 °C were investigated using a ball-on-disc wear test. The results show that the TiAlN coating is primarily composed of c-TiN and c-AlN hard phases, and the bonding strength of TiAlN coating with the Cr-Ni coating is 22.15 N. The average coefficients of friction of TiAlN/Cr-Ni coating at 400, 500 and 600 °C are 0.458, 0.318 and 0.449, respectively, and the corresponding wear rates are 0.329 × 10{sup −3}, 0.384 × 10{sup −3} and 0.205 × 10{sup −3} mm{sup 3} N{sup −1} s{sup −1}, respectively, and the wear mechanism includes adhesive wear and oxidation wear.

36 MATERIALS SCIENCE↗

Binder Jetting: A Novel NdFeB Bonded Magnet Fabrication Process

Our goal of this research is to fabricate near-net-shape isotropic (Nd) 2 Fe 14 B-based (NdFeB) bonded magnets using a three dimensional printing process to compete with conventional injection molding techniques used for bonded magnets. Additive manufacturing minimizes the waste of critical materials and allows for the creation of complex shapes and sizes. The binder jetting process works similarly to an inkjet printer. A print-head passes over a bed of NdFeB powder and deposits a polymer binding agent to bind the layer of particles together. The bound powder is then coated with another layer of powder, building the desired shape in successive layers of bonded powder. Upon completion, the green part and surrounding powders are placed in an oven at temperatures between 100°C and 150°C for 4–6 h to cure the binder. After curing, the excess powder can be brushed away to reveal the completed “green” part. Green magnet parts were then infiltrated with a clear urethane resin to achieve the measured density of the magnet of 3.47 g/cm 3 close to 46% relative to the NdFeB single crystal density of 7.6 g/cm 3 . Magnetic measurements indicate that there is no degradation in the magnetic properties. In conclusion, this study provides a new pathway for preparing near-net-shape bonded magnets for various magnetic applications.

36 MATERIALS SCIENCE↗

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. Furthermore, this work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

36 MATERIALS SCIENCE↗

Methodology for Thermodynamic Analysis Coupled with Computational Fluid Dynamics Modeling for Casting a Novel Aluminum–Cerium Alloy

In this paper, we present the results of computational fluid dynamics (CFD) analysis to assess castability, porosity, molten metal fluidity and other technological properties of a new Al-Ce alloy. A thermodynamic analysis of a new Al-Ce alloy is done to obtain the physical properties as a function of temperature across both solid and liquid phases. These properties are then used to build the CFD of model the full casting process from initial pouring through to final solidification of the part, here an example of a heavy duty mor mount is used. While several excellent commercial CFD codes exists this process shows that CFD can be used to assess the capability of the alloy to properly fill the mold, as well as give predictions where scattered porosity or large-scale defects may occur in the casting. Further, unlike the commercially available software (e.g., ProCAST, SOLIDCast , MAGMASOFT®) the complex 3D-analysis of the stress / strain fields in cast parts is not performed at this time. However, the availability of free software for assessing the required thermodynamic / thermo-physical properties of new alloys (OpenCALPHAD) and CFD codes such as OpenFOAM® makes the developed option attractive and economical, especially for the analysis of new Al-Ce alloys, for which the available data does not exist.

36 MATERIALS SCIENCE↗

High Speed In-situ X-ray Imaging of 3D Freeze Printing of Aerogels

3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.

36 MATERIALS SCIENCE↗

Fused filament fabrication of novel phase-change material functional composites

Additively manufactured polymer heat exchangers are of recent interest in the thermal sciences due to their lightweight and intricate heat-transfer-enhancing geometrical features. The goal of the present research is to directly encapsulate phase-change material (PCM) into polymer filament for the purpose of 3D printing polymer heat exchangers capable of latent heat thermal energy storage and management. PCMs have the ability to absorb large amounts of latent heat while undergoing a solid-to-liquid phase change at a nearly constant temperature. Encapsulation or containment of PCMs is necessary to prevent leaking since the material continuously cycles between a liquid and a solid state. An organic-based PCM and high-density polyethylene (HDPE) were combined and extruded into a functional composite filament. For the first time, with the aid of a heated enclosure and HDPE build plates, it was demonstrated that these functional composite materials can be printed using fused filament fabrication (FFF). Printing HDPE is known to be difficult; however, based on what was observed in the current study, the PCM and HDPE composite was easier to print than pure HDPE. Thermal properties, such as latent heat of fusion, phase-change temperature, and thermal conductivity, of the composite filament and 3D printed samples were investigated and compared with compression-molded bulk material. Finally, the microstructures of the composite filament and 3D printed samples were visualized, and the basic structures of the HDPE and PCM within both the filament and 3D printed parts were clearly delineated.

36 MATERIALS SCIENCE↗

Influence of fluorescent dopants on the vat photopolymerization of acrylate-based plastic scintillators for application in neutron/gamma pulse shape discrimination

Plastic scintillators, a class of solid-state materials used for radiation detection, were additively manufactured with vat photopolymerization. The photopolymer resins consisted of a primary dopant and a secondary dopant dissolved in a bisphenol A ethoxylate diacrylate-based matrix. The absorptive dopants significantly influence important print parameters, for example, secondary dopants decrease the light penetration depth by a factor > 12×. The primary dopant 2,5-diphenyloxazole had minimal impact on the printing process even when loaded at 25 % by mass of the resin. Working curve measurements, which relate energy dose to cure depth, were performed as a function of feature size to further assess the influence of dopants. Photopatterns smaller than 150 µm width had apparent increases in critical energy dose compared to larger photopatterns, while all resins maintained printed features in line gratings with 50 µm of separation. Printed scintillator monoliths were compared to scintillators cast by traditional molding, demonstrating that the layer-by-layer printing process does not decrease scintillation response. In conclusion, a maximum light output of 31 % of a benchmark plastic scintillator (EJ-200) and successful pulse shape discrimination were achieved with 20 % by mass 2,5-diphenyloxazole as the primary dopant and 0.1 % by mass 9,9-dimethyl-2,7-distyrylfluorene as the secondary dopant in printed scintillator samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fully printed and integrated electrolyzer cells with additive manufacturing for high-efficiency water splitting

Using additive manufacturing (AM) technology, a fundamental material and structure innovation was proposed to significantly increase the energy efficiency, and to reduce the weight, volume and component quantity of proton exchange membrane electrolyzer cells (PEMECs). Four conventional parts (liquid/gas diffusion layer, bipolar plate, gasket, and current distributor) in a PEMEC were integrated into one multifunctional AM plate without committing to tools or molds for the first time. In addition, since the interfacial contact resistances between those parts were eliminated, the comprehensive in-situ characterizations of AM cells showed that an excellent energy efficiency of up to 86.48% was achieved at 2 A/cm2 and 80 degrees C, and the hydrogen generation rate was increased by 61.81% compared to the conventional cell. More importantly, the highly complex inner structures of the AM integrated multifunctional plates also exhibit the potential to break limitations of conventional manufacture methods for hydrogen generation and to open a door for the development of other energy conversion devices, including fuel cells, solar cells and batteries.

36 MATERIALS SCIENCE↗